Home

Tenda W150M+

Contents

1. gt Wireless Router Always blue indicates the device in Wireless Router mode gt WPS Blinking means the device is negotiating with the client in WPS mode gt LAN WAN Always blue indicates the Ethernet cable is well connected and blinking indicates it is transmitting data packets Back and Rear panel and LED Indicators show 7 IN p O Oo WPSRESET MODE 2 iit WIN WIN LAN WAN LED indicators description of the back and side panel From L to R gt WPS RESET Wi Fi Protection Setup button and system reset button Press it for I second the WPS feature will be enabled and WPS indicator will be shown blinking Press this button for 7 seconds the settings configured in this device will be Tenda W150M 150Mbps Wireless AP gt deleted and it will restore the settings to the default one Power The port is for USB line connection Please use the included USB line connected with the power adapter or the USB port of computer LAN WAN The 100Mbps Ethernet port in Wireless Router mode it is a WAN access port to connect the DSL MODEM generally While in AP WISP mode Client AP mode WDS AP mode WISP Router mode it is a LAN port to connect the PC Router and Ethernet Switch Tenda W150M 150Mbps Wireless AP Chapter 2 Hardware Installation 2 1 How to Install the Router After you unpack the box please follow the steps below to connect the device For better wireless performance ple
2. AppendixIV Troubleshooting In this part some questions and problems shown during the Router s usage and installation will be given suggesting answers If your problems are not in the list please log into our website www tenda cn or send an E mail to support tenda cn and we will reply you in the earliest time 1 Enter the IP address but can not visit the WEB management interface What can I do Please make sure the cable is well connected and the corresponding indicator is light Make sure the device is not in Wireless Router mode In this mode you can visit the WEB interface only by Wireless network In the wireless access point AP mode your computer must specify an IP 192 168 2 2 192 168 2 254 to access the device Please click Start Run to enter ping 192 168 2 1 to diagnose whether the device is connected If it can ping pass then check whether your browser enable a proxy server If enabled please disable it If you can not ping pass you can hold down the RESET button for 7 seconds to restore the factory settings and ping192 168 2 1 again 2 Forget the login password and can not enter the setting page What can I do Press the RESET button for 7 seconds to restore the Router to default settings 3 The computer connected with the Router shows IP address 89 Tenda W150M 150Mbps Wireless AP conflict What can I do Check if there are other DHCP servers in the LAN If there have disable
3. Tip Routers in hotels support DHCP function which can assign IP 22 Tenda W150M 150Mbps Wireless AP addresses automatically You only need to configure you computer to obtain IP address and DNS sever automatically to access the internet Setting ways refer to 4 1 5 2 Client AP Log on the web based interface as chapter 4 and then configure the mode as below 5 2 1Select Client AP click Setup Wizard and Next button 5 2 2 Configure the parameters sD Tenda 00 10 18 01 02 24 WPA2 PSK v Om ars 12345678 SSID SSID Service Set Identifier is the unique name of the wireless network Input the SSID of the AP you want to 23 Tenda W150M 150Mbps Wireless AP connect lt MAC Address The Router s physical MAC address as seen on your local network is unchangeable Input the MAC address of the AP you want to connect Sometimes MAC address is also named BSSID BSSID Basic Service Set Identifier of wireless network In IEEE802 11 BSSID is the MAC address of wireless access point lt Channel Specify the effective channel from I to 13 Auto of the wireless network The channel you select must be correspondence with the AP lt Security Mode The security mode you set should be the same as the AP More details please refer to the Wireless Security Settings chapter We recommend you Scan the access points and then select the SSID in your scanned SSID
4. 28 Tenda W150M 150Mbps Wireless AP with the AP at the maximum speed of 54Mbps 11b g mode Allow the 11b g compliant client device to connect with the AP with auto negotiation speed and lln wireless client to connect the device with 11g speed 11b g n mode Allow 11b g n compliant client device to connect gt with the AP with auto negotiation speed SSID SSID Service Set Identifier is the unique name of the wireless network Wireless client must input the same SSID as the device to access Channel Specify the effective channel from 1 to 13VAuto of the wireless network Broadcast SSID Select Disable to disable the device s SSID to be invisible by the wireless client If you disable it client must input the same SSID as the device to access BSSID Basic Service Set Identifier of wireless network In IEEE802 11 BSSID is the MAC address of wireless access point Extend Channel To increase data throughput of wireless network the extension channel range is used in 11n mode Channel Bandwidth Select the channel bandwidth to improve the wireless performance When the network has 11b g and 11n clients you can select the 40M when it is an 11n network select 20 40M to improve its throughput Click Next to save configurations Note We suggest you do not change the channel in this mode or else you can not access the device which you want to connect For wireless network encryption please refer t
5. Auto Mcs Auto Reverse Direction gt Gran RDG O Disable Enable Extension Channel Aggregation MSDU gt amp MSDU Dissble O Enable Enable Wireless Check to enable the Router s wireless features uncheck to disable it Network Mode Select one mode from the following The default is 11b g n mode lib mode Allow the wireless client to connect with the device in 11b mode at the maximum speed of 1 1Mbps lig mode Allow the 11g lln compliant client device to connect with the AP at the maximum speed of 47 Tenda W150M 150Mbps Wireless AP 54Mbps 11b g mode Allow the 11b g compliant client device to connect with the AP with auto negotiation speed and lIn wireless client to connect the device with 11g speed 11b g n mode Allow the 11b g n compliant client device to connect with the AP with auto negotiation speed lt V SSID SSID Service Set Identifier is the unique name of the wireless network This device has two SSID and the main SSID is necessary lt Broadcast SSID Select Enable to enable the device s SSID to be visible by wireless clients The default is enabled If you disable it the clients must know the SSID to communicate BSSID Basic Service Set Identifier of wireless network In IEEE802 11 BSSID is the MAC address of wireless access point lt Standard Channel Specify the effective channel from I to 13 Auto of the wireless network lt Extension Channel
6. 86 755 25312445 25312442 83737333 extension no 8310 or 8318 Fax 86 755 27057244 E mail sales tendabx com USA Branch Add 6955 N Durango Dr Suite 1115 10 Las Vegas NV 89149 U S A Tel 1 702 483 5366 Email biz tendausa com Technical Support Tel 1 800 570 5892 1 800 207 3434 Technical Support Email support tendausa com Russia Branch Anpec r Mockpa y11 Moc unbMoBckaa 1 76 Te 7 495 1478274 M06 79261309686 Email 2576 tenda com cn SKYPE waluojia88 Pycckuii s3bIk India Branch Email sales tenda com cn Singapore Branch Email sales tenda com cn Viet Nam Branch Add No 19 6th Lane Doan Ke Thien Street Cau Giay 94 Tenda W150M 150Mbps Wireless AP District Ha Noi Viet Nam Tel 0084 097 9955 122 Email sales tenda com cn SHENZHEN TENDA TECHNOLOGY CO LTD www tenda cn 95 Tenda W150M 150Mbps Wireless AP Appendix V Regulatory Information EU Declaration or Declaration of Conformity Hereby SHENZHEN TENDA TECHNOLOGY CO LTD declares that this Wireless Broadband Router is in compliance with the essential requirements and other relevant provisions of Directive 1999 5 EC FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radia
7. ASCII characters Key Renewal Interval Set the key s renewal period 7 2 3 Mixed WEP WEP Wired Equivalent Privacy a basic encryption method usually encrypts wireless data using a series of digital keys 64 bits or 128 bits in length By using the same keys on each of your wireless network devices you can prevent unauthorized wireless devices from monitoring your transmissions or using your wireless resources Select Mixed WEP to enter the following window 51 Tenda W150M 150Mbps Wireless AP Security Settings SSID Tenda Security Mode Mixed WEP v Default Key Key 1 v WEP Key 1 333333 Hex m WEP Key 2 Hex x WEP Key3 Hex WEP Key 4 Hex x Notice Wireless Security Settings 802 1 In only defines three standard encryption methods Open None Disable WPA Personal AES WPA2 Personal AES Other encryption methods are nonstandard There may be compatibility problems among different manufacturers Apply Cancel lt SSID Select the SSID main SSID or minor SSID to configure security setting from the drop down menu lt Security Mode From the drop down menu select the corresponding security encryption modes WEP Key Set the WEP key with the format of ASCII or Hex lt Key Explanation You can enter ASCII code 5 or 13 ASCII characters Illegal character as is not allowed Or 10 26 hex characters lt Default Key Select one key from th
8. Apply to activate it 7 How to share my computer s source with other users in Internet If you want Internet users to access the internal server via the Router such as e mail server Web FTP you can configure the Virtual Server to come true Step 1 create your internal server make sure the LAN users can access these servers and know related service port For example Web server s port is 80 FTP is 21 SMTP is 25 and POP3 is 110 Step 2 in the Router s web click Virtual Server and select Single Port Forwarding Step 3 input the external service port given by the Router for example 80 Step 4 input the internal Web service port for example 80 Step 5 Input the internal server s IP address If your Web server s IP address is 192 168 2 10 please input it Step 6 select the communication protocol used by your internal host TCP UDP and ICMP Step 7 click Apply to activate the settings The following table has listed the well known application and service port 91 Tenda W150M 150Mbps Wireless AP o0 O Kj FR OE File Send 6891 6900 TCP MSN TCP UDP Voice 1863 6901 TCP Messenger Voice 1863 5190 UDP Why can t I use wireless WAN function to access the Internet Please make sure that the wireless adapter can access the Internet when connected to the computer wireless signals scanned by the adapter are strong enough and quality of signals is good en
9. Assigned by DHCP Ta IP Address 192 168 0 100 Subnet Mask 255 255 255 0 Default Gateway 192 168 0 1 Windows did not detect problems with this connection If you cannot connect click Repair Close 84 Tenda W150M 150Mbps Wireless AP Appendix II How to set the network card after device encrypted When the device is encrypted you need to enter password to connect to the wireless device to access the internet Set up a wireless network adapter as follows 1 On your computer desktop right click My Network Places and select Properties LAN or High Speed Internet ral Local Area Connectiorf3 ad ee OE ices ell F Wireless Network Connection 2 Ne nec 2 Select View Available Wireless Network The entire wireless signal will be shown in the interface Please select Tenda If you don t find it please click Refresh Network List hier null Choose wireless network CO av bm tb car to a v re eter ange aa got more mr EN MOINE enn revet PA will Te rede Dm hay ya mae 1 annet ta oe eter dd oet Dink 85 Tenda W150M 150Mbps Wireless AP 3 Select Tenda and click Connect or double click Tenda input the Network key and Confirm network key to connect the Router a 4 ee Choma a wireless network Bie Bo ha tm nro o wo re OD pp Stent ed Mamie Va men em ba sed Eh ov a Sr TT VEE eneren eten
10. H 192 168 2 TCP w 9 H 192 168 2 TCP w 10 H 192 188 2 TCP w Veko DNS 53 Add 1D mo Service Port lt Start End Port Enter the start end port number which ranges the External ports used to set the server or Internet applications lt IP Address Enter the IP address of the PC where you want to 62 Tenda W150M 150Mbps Wireless AP set the applications lt Protocol Select the protocol TCP UDP Both for the application lt Enable Click to check it for corresponding operation gt Delete Click to clear the parameters lt Well Known Service Port Select the well known services as DNS FTP from the drop down menu to add to the configured one above For the port not in the list you can input manually lt Add Add the selected well known port to the policy ID The server at the IP address of 192 168 2 10 in LAN provides WEB service at the port of 80 and Telnet service at the port of 23 If you want the clients on the Internet to visit this server please set the device as the diagram above NOTE If you set the virtual server of the service port as 80 you must set the Web management port on Remote Web Management page to be any value except 80 such as 8080 Otherwise there will be a conflict to disable the virtual server 9 2 DMZ Settings In some special cases we need to completely expose a computer in LAN to the WAN to achieve intercommunication This computer
11. MAC address as seen on your local network is unchangeable lt IP Mode There are two modes Static IP and Dynamic IP If you select Static IP you need to input the parameters provided by your ISP If you choose Dynamic IP you should adjust the connection properties to obtain an IP address and DNS sever automatically in Internet protocol lt IP Address The device s LAN IP addresses 192 168 2 1 is the default value If you change it you need to use the new IP to login to the Web interface lt Subnet Mask It s shown the device s subnet mask for measurement of the network size 255 255 255 0 is the default value lt Default Gateway Input the Gateway provided by your ISP If you are not sure please consult your ISP lt Primary DNS Sever Input the primary DNS sever provided by your ISP lt Secondary DNS Sever you can input it or empty it The 41 Tenda W150M 150Mbps Wireless AP parameters are also provided by your ISP lt Host Name The device s wins name which you can use it to visit the device Notice Once you changed the IP address of the LAN port you should use the new IP to enter into the Web interface 6 2 WAN Settings WAN setting is only for WISP mode and Wireless Router mode 6 2 1 ADSL Virtual Dial up via PPPoE WAN Setting WAN connection mode PPPoE pppoe user 1460 WAN Co
12. Tenda W150M 150Mbps Wireless AP Connection Method O Dynamic IP via DHCP Static IP ADSL Virtual Dial up via PPPoE GLT OrPTP User Name pppoe user Password pppoe passwd Back Next You can view the status by click Status Information after the device rebooted If there shows IP address of WAN port you can access to the internet For further settings please refer to the following chapters 5 5 3 Wireless Basic Setting Wireless Basic Setting Network Mode 11b g n mixed mode v SSD Tenda Broadcast SSID BSSID MCS Auto v s t Disable Enable 2417MHz Channel 2 v Disable Enable Back Next Network Mode Select one mode from the following The default is 11b g n mode 36 Tenda W150M 150Mbps Wireless AP 11b mode Allow the wireless client to connect with the device in 11b mode at the maximum speed of 11Mbps lig mode Allow the Ilg IIn compliant client device to connect with the AP at the maximum speed of 54Mbps 11b g mode Allow the 11b g compliant client device to connect with the AP with auto negotiation speed and 11n wireless client to connect the device with 11g speed 11b g n mode Allow 11b g n compliant client device to connect with the AP with auto negotiation speed lt SSID SSID Service Set Identifier is the unique name of the wireless network Wireless client must input the same SSID to access lt Channel Specify the effec
13. To increase data throughput of wireless network the extension channel range is used in I In mode lt Channel Bandwidth Select the channel bandwidth to improve the wireless performance When the network has 11b g and 11n clients you can select the 40M when it is an I In network select 20 40M to improve its throughput 48 Tenda W150M 150Mbps Wireless AP 7 2 Wireless Security Setting It is used to configure the AP network s security setting Here presents the common encryption methods including WPA personal WPA2 personal WAP WAP2 Personla Mixed WEP Open Shared It is suggested you choose WPA personal for Security Mode and AES for WPA Algorithms Please note that all connecting wireless devices will need to match these security settings in their connection settings In this section three common encryption methods are introduced 7 2 1 WPA personal WPA Wi Fi Protected Access a Wi Fi standard is a more recent wireless encryption scheme designed to improve the security features of WEP It applies more powerful encryption types such as TKIP Temporal Key Integrity Protocol or AES Advanced Encryption Standard and can change the keys dynamically on every authorized wireless device 49 Tenda W150M 150Mbps Wireless AP Security Settings SSID Tenda Security Mode WPA Personal h WPA Algorithms aks OTKIP TKIP amp AES Pass Phrase 12345678 Key Renewal Interval 3600 second Notic
14. can be set to the DMZ host 63 Tenda W150M 150Mbps Wireless AP DMZ Settings IMPORTANT When enabled the DMZ host the firewall settings of the computer will not function DMZ host IP 192 168 2 100 Enable Apply Cancel DMZ Host IP Address The IP address of the computer you want to expose lt Enable Click it to enable the DMZ host For example Set the computer at the IP address of 192 168 2 100 in LAN as a DMZ Host to intercommunicate with another host on the Internet IMPORTANT When the DMZ host is enabled the firewall settings of the DMZ host will no longer works 9 3 UPnP Settings It supports latest Universal Plug and Play This function goes into effect on Windows XP or Windows ME or this function would go into effect if you have installed software that supports UPnP With the UPnP function host in LAN can request the router to process some special port switching so as to enable host outside to visit the resources in the internal host 64 Tenda W150M 150Mbps Wireless AP UPnP Settings Enable UPnP v Apply Cancel Enable UPnP Click the checkbox to enable the UPnP 65 Tenda W150M 150Mbps Wireless AP Chapter 10 Security Settings The security settings are for WISP mode and Wireless Router mode 10 1 Client Filter Settings To facilitate your further management to online b
15. is the MAC address of wireless access point Extend Channel To increase data throughput of wireless network the extension channel range is used in 11n mode Channel Bandwidth Select the channel bandwidth to improve the wireless performance When the network has 11b g and 11n clients you can select the 40M when it is an 25 Tenda W150M 150Mbps Wireless AP I In network select 20 40M to improve its throughput Click Next to save configurations Note We suggest you do not change the channel in this mode or else you can not access the device which you want to connect 5 2 4 Wireless Security Settings It is suggested that you choose WPA personal for Security Mode and AES for WPA Algorithms Input 8 63 numbers letters and symbols for pass phrase Click Next to save the configuration More details please refer to the following chapter Click Apply to save the configurations and the router will be rebooted automatically Setup Wizard The configuration is completed Click Apply to activate your settings or press Back to change your settings 26 Tenda W150M 150Mbps Wireless AP Note Make sure the device have the same Channel Security mode and Extend channel as the access point 5 3 WDS AP Mode Setup Wizard Log on the web based interface as chapter 4 and then configure the mode as below 5 3 1 Select WDS AP click Setup Wizard and Next button Tenda Wirel
16. key generated by AP automatically APPIN KEY The PIN code used by default Reset OOB When this button is pressed the WPS client will be idle state and WPS indicator will be turned off AP will not respond the WPS client s requests 7 5 Wireless Access Control To secure your wireless LAN the wireless access control is actually based on the MAC address management to allow or block the specific clients to access the wireless network Select WLAN Setting gt Access Control to display the following screen 56 Tenda W150M 150Mbps Wireless AP Wireless Access Control MAC Address Filter Allow MAC Address Management MAC Address Action 00 11 22 33 44 55 Add 00 11 22 33 44 55 Delete Apply Cancel lt MAC Address Filter Allow Block MAC address filter Select off to mal function MAC address Block to prevent the MAC addresses in the list from accessing the wireless network Allow to allow the MAC address in the list to access the wireless network MAC Address Management Input the MAC address to implement the filter policy Click Add to finish the MAC add operation lt MAC Address list Show the added MAC addresses You can add or delete them 7 6 Connection Status This page shows wireless client s connection status including MAC address Channel bandwidth Select WLAN Sett
17. need to be apart by a comma 10 3 MAC Address Filter In order to manage the computers in LAN better you could control the computer s access to Internet by MAC Address Filter MAC Filter MAC Filtering Settings V Enable Access Policy 10 Enable V Delete the Policy Clear Disable Filtering Mode access the Internet Enable Policy Name alice MAC Address 00 co OF FLAD LFF EF LCS Times 8 mlio y 18 0 v Date V Everyday Sun Mon Tue Wen Thr _ Fri Sat Cancel MAC address filter Enable it to filter MAC address Access Policy Select one number from the drop down menu Enable Click this to enable the policy o gt Filter Mode Click one radio button to enable or disable to access the Internet in specific time Every rule is applicable 69 Tenda W150M 150Mbps Wireless AP only to the corresponding MAC address lt Policy Name Enter a name for the access policy selected lt MAC Address Enter the MAC address of the computer you want to run the access policy lt Times Select the time range of client filter lt Date Select the day s to run the access policy lt Apply Select Apply to enable the settings For example If you want to configure the host with MAC address 00 22 15 55 2A 15 not to access the Internet at 9 00 18 00 from Monday to Friday y
18. the GMT time again once it has access to the Internet Time Settings Time Zone GMT 08 00 Bejing China Hong Kong Singapore Taipei v Notice GMT time can be obtained only after accessing to the Internet Customized time Apply Cancel lt Time Zone Select your time zone from the drop down menu lt Customized time Enter the time you customize Note When the Router is powered off the time setting will be lost Before the Router will obtain GMT time automatically you need connect with the Internet and obtain the GMT time or set the time on this page first Then the time in other features e g firewall can be activated 12 2 DDNS 74 Tenda W150M 150Mbps Wireless AP The DDNS Dynamic Domain Name System is supported in WISP mode and Wireless Router mode It is to assign a fixed host and domain name to a dynamic Internet IP address which is used to monitor hosting website FTP server and so on behind the Router If you want to activate this function please select Enable and a DDNS service provider to sign up 3322 org Sign up tenda seecccee Domain Name tenda 3322 0rg Apply Cancel gt Main Features 1 Owing to ISP most times provides dynamic IP address DDNS is used to capture the changeable IP address and match the fixed domain Then users can have access
19. the internet with your neighbor you can choose this mode to get a stable signal In addition it can access to the IPTV set top box broadband satellite receiver and such devices This mode is very simple avoiding the cumbersome cables The topology is as follows More details please refer to 5 2 Tenda W150M 150Mbps Wireless AP Internet Coz Aq A 3 3 WDS AP Mode In this mode the device can enhance the signal and extend the wireless coverage It can bridge two local area networks or two computers and meanwhile amplify and transfer the signals The WDS AP mode is similar as WDS mode Besides many wireless clients can access when the device works as a bridge The topology is as follows A l PA D CCC Sy Internet VG ye Tenda W150M 150Mbps Wireless AP LAN1 LAN2 vl Ta More details please refer to 5 3 3 4 WISP Mode In this mode you do not need to configure the signal transmitter but only to simply configure the W150M to amplify the wireless signal and multi computers can share the internet The device supports DHCP function to assign IP addresses automatically and NAT function If you enable the WISP outside the house but the inside WISP AP signal is poor the device can enhance the signal and improve the speed If more than one wired computer access you can connect the LAN port of the device to the switch and the switch to the computer The network topology is as follows Tenda W150M 150Mbps Wire
20. them The default IP address of the Router is 192 168 2 1 and please maker sure the address is not occupied by other devices If there are two computers with the same IP addresses please modify one 4 My computer can not log in equipment can not access the internet and a yellow triangle with exclamation point symbols shows how to deal with This problem is due to your network card is not assigned the IP address If set your computer to automatically obtain IP please ensure that the source of the router s DHCP is turned on DHCP can automatically assign an IP address to your computer If there is no DHCP please set a static IP address and fill in gateways and DNS otherwise you can not access Internet 5 I can not use E mail and access the Internet What can I do It happens in ADSL connection and Dynamic IP users And you need modify the default MTU value 1492 Please in the WAN Setting modify the MTU value with the recommended value as 1450 or 1400 6 How can I configure and access the Internet via Dynamic IP In Setup Wizard of the Web utility interface select Dynamic IP connection type and click Save to activate it As some ISPs bind the user computer s MAC address you need to clone the Router s 90 Tenda W150M 150Mbps Wireless AP WAN MAC address to the bind2ling PC s MAC address Select MAC Address Clone in Advanced Setting to input your computer s MAC address and click
21. to the Internet to communicate with others 2 DDNS can help you establish virtual host in your home and company lt Service Provider Select one from the drop down menu and press Sign up for registration lt User Name Enter the user name the same as the registration name lt Password Enter the password you set 75 Tenda W150M 150Mbps Wireless AP lt Domain Name Enter the domain name which is optional User name tenda Password 123456 Domain name tenda 3322 org After mapping the port in the virtual server setting account information in DDNS server and in the address field entering http tenda 3322 org you can access the Web page 12 3 Backup Restore Settings The device provides backup restore settings so you need set a directory to keep these parameters Backup Restore Please choose restore file The device provides backup restore settings so you need set a directory to keep these parameters Backup Browse Restore gt Backup Setting Click Backup button to back up the Router s settings and select the path for save 76 Tenda File Download W150M 150Mbps Wireless AP Do you want to open or save this file Oa Name RouterCfm cfg Da Type Microsoft Office Outlook 6 10 KB From 192 168 2 1 v Always ask before opening this type of file While files from the Intern
22. your PC s MAC address lt Restore Default MAC Address Restore to the default hardware MAC address 6 4 DNS Settings DNS is short for Domain Name System or Service an Internet service that translate domain names into IP addresses which are provided by your Internet Service Provider Please consult your Internet Service Provider for details if you do not have them 45 Tenda W150M 150Mbps Wireless AP DNS Settings DNS Settings v Primary DNS Address 202 968 134 133 Secondary DNS Address 202 96 128 68 optional Apply DNS Settings Click the checkbox to enable the DNS server The Router s DHCP sever will answer the client s requests and distribute DNS address Primary DNS Address Enter the necessary address provided by your ISP Secondary DNS Address Enter the second address if your ISP provides which is optional Notice After the settings are completed reboot the device to activate the modified settings 46 Tenda W150M 150Mbps Wireless AP Chapter 7 Wireless Setting 7 1 Basic Settings Basic Settings Z Enable Wireless 1 Network Mode 11b g n mixed mode Main SSID Tenda Minor SSID Broadeast SSID Enble O Disable MBSSID AP Isolation O Enable Disable AP Isolation O Enbe Disable BSSID 00 B0 2C 01 02 10 Channel AutoSelect v Operating Mode Mixed Mode O Green Field Channel BandWidth 020 20 40 Guard Interval Olong
23. 100Mbps Auto Negotiation Ethernet port for LAN WAN Support xDSL Cable Modem static and dynamic IP in community network Support remote WEB management Support wireless roaming technology for high efficient wireless connection Support SSID stealth mode and access control based on MAC address up to 30 groups Provide sys log to record the status of Router Support auto negotiation or manual mode for IEEE802 11b IEEE802 11g IEEE802 11n Support UPnP and DDNS Support LAN access control over internet connection Support virtual Sever and DMZ host Built in firewall for hacker s attack prevention 1 3 Package contents VV v Y Please unpack the box and check the following items One W150M 150Mbps wireless AP One power adapter One quick installation guide One CD Tenda W150M 150Mbps Wireless AP gt One Ethernet cable gt One USB line If any of the items do not match are missing or damaged please contact the store you purchased this device from for immediate replacement 1 4 LED Indicator and Port Description Front Panel and LED Indicator Show LED indicators description on front panel From L to R gt AP Always blue indicates the device in AP working mode gt Clientt tAP Always blue indicates the device in Client AP working mode gt WDS AP Always blue indicates the device in WDS AP Tenda W150M 150Mbps Wireless AP mode gt WISP Router Always blue indicates the device in WISP Router mode
24. AP More details please refer to the Wireless Security Settings chapter We recommend you Scan the access points and then select the SSID in your scanned SSID list for convenience Click Next to the following interface 5 4 3 Wireless Basic Setting Wireless Basic Setting 11b g n mixed mode v Tenda Disable GI Enable 2452MHz Channel 9 Disable O Enable Back Next 31 Tenda W150M 150Mbps Wireless AP Network Mode Select one mode from the following The default is 11b g n mode 11b mode Allow the wireless client to connect with the device in 11b mode at the maximum speed of 11 Mbps lig mode Allow the 11g l1n compliant client device to connect with the AP at the maximum speed of 54Mbps 11b g mode Allow the 11b g compliant client device to connect with the AP with auto negotiation speed and lin wireless client to connect the device with 11g speed 11b g n mode Allow 11b g n compliant client device to connect with the AP with auto negotiation speed lt SSID SSID Service Set Identifier is the unique name of the wireless network Wireless client must input the same SSID as the device to access lt Channel Specify the effective channel from I to 13 Auto of the wireless network lt Broadcast SSID Select Disable to disable the device s SSID to be invisible by the wireless client If you disable it client must input the same SSID as th
25. Click Add to add the entry in the list lt Hostname The name of the computer which is added a new IP address lt Lease Time The left time length of the corresponding IP address lease 61 Tenda W150M 150Mbps Wireless AP Chapter 9 Virtual Server Virtual Server feature is only for wireless signal amplification mode and the wireless Router mode 9 1 Port Range Forwarding This section deals with the port range forwarding mainly The Port Range Forwarding allows you to set up a range of public services such as web servers ftp e mail and other specialized Internet applications to an assigned IP address on your LAN Port Range Forwarding The Router can be configured as a virtual server on behalf of local services behind the LAN port The given remote requests will be re directed to the local servers via the virtual server This section deals with the port range forwarding mainly The Port Range Forwarding allows you to set up kinds of public services such as web servers ftp e mail and other specialized Intemet applications on your network NO Start Port End Port To IP Address Protocol Enable Delete 1 He 192 168 2 10 TCP w 2 H 192 168 2 TCP 3 H 192 168 2 TCP v 4 H 192 168 2 TCP v 5 H 192 168 2 TCP w 8 H 192 168 2 TCP w 7 H 192 168 2 TCP w 8
26. Mbps Wireless AP parameter controls what size data packet the frequency protocol issues to RTS packet The default value of the attribute is 2346 It is recommended not to modify this value in SOHO environment lt TX Power Set the output power of wireless radio The default value is 100 lt WMM Capable It will enhance the data transfer performance of multimedia data when they re being transferred over wireless network It is recommended to enable this option lt APSD Capable It is used for auto power saved service The default is disabled 7 4 WPS Settings WPS Wi Fi Protected Setting can be easy and quick to establish the connection between the wireless network clients and the device through encrypted contents The users only enter PIN code or press WPS button on the panel to configure it without selecting encryption method and secret keys by manual In the WLAN settings menu click WPS settings to enter the next screen 54 Tenda W150M 150Mbps Wireless AP WPS Config You could setup security easily by choosing PIN or PBC method to do Wi Fi Protected Setup WPS Settings O Disable Enable WPS mode pec OPIN WPS Summary WPS Cunent Status Idle WPS Configured Yo WPS SSID Tenda WPS Auth Mode WPA2 PSK WPS Encryp Type AES WPS Default Key Index 2 WPS Key ASCII 88888888 AP PIN 01090727 Save Reset 00B WPS settings To enable or disable WPS function The d
27. Tenda User Guide www tenda cn 150Mbps Wireless AP Tenda W150M 150Mbps Wireless AP Tenda is the registered trademark of Shenzhen Tenda Technology Co Ltd All the products and product names mentioned herein are the trademarks or registered trademarks of their respective holders Copyright of the whole product as integration including its accessories and software belongs to Shenzhen Tenda Technology Co Ltd Without the permission of Shenzhen Tenda Technology Co Ltd any individual or party is not allowed to copy plagiarize imitate or translate it into other languages All the photos and product specifications mentioned in this manual are for references only As the upgrade of software and hardware there will be changes And if there are changes Tenda is not responsible for informing in advance If you want to know more about our product information please visit our website at www tenda cn Tenda W150M 150Mbps Wireless AP Content CHAPTER 1 PRODUCT OVERVIEW esovesseessersneesnvsnnrsnnesnnsenesene 4 1 1 Production introduction rrvvrsvverrovrrenvvrrsrrrrnverrsrrrevvvnssrresnveernrr 4 1 2 Products Features rrarvranvrnrvrrrsnverrsvrrenvvnssrrssnvenssvrrenvvassrvssnvessnrr 5 1 3 Package contents ariii eea a a a 6 1 4 LED Indicator and Port Description msarnrsnernrrnrrnrrnrrnrrnnrerenn 7 CHAPTER 2 HARDWARE INSTALLATION cccsccceseseees 10 2 1 How to Install the Router srarsnr
28. ansmission WEP adds data encryption to every single packet transmitted in the wireless network The 40bit and 64bit encryption are the same because of out 64 bits 40 bits are private Conversely 104 and 128 bit are the same WEP uses a common KEY to encode the data Therefore all devices on a wireless network must use the same key and same type of 87 Tenda W150M 150Mbps Wireless AP encryption There are 2 methods for entering the KEY one is to enter a 16 bit HEX digit Using this method users must enter a 10 digit number for 64 bit or 26 digit number for 128 bit in the KEY field Users must select the same key number for all devices The other method is to enter a text and let the computer generate the WEP key for you However since each product use different method for key generation it might not work for different products Therefore it is NOT recommended using WPA WPA2 A security protocol for wireless networks that builds on the basic foundations of WEP It secures wireless data transmission by using a key similar to WEP but the added strength of WPA is that the key changes dynamically The changing key makes it much more difficult for a hacker to learn the key and gain access to the network WPA2 is the second generation of WPA security and provides a stronger encryption mechanism through Advanced Encryption Standard AES which is a requirement for some government users 88 Tenda W150M 150Mbps Wireless AP
29. arameters This device supports three kinds of access ways ADSL virtual dial up dynamic IP static IP please select the ways according to the actual situation If you are not sure you can consult local Internet service providers to get the relevant parameters gt Dynamic IP DHCP The default access method is Dynamic IP If your ISP provides you the Dynamic IP you can choose Dynamic IP access way Every time you access the internet you will get different IP Differ from the other two ways you don t need to input the parameters Click Next button directly Connection Method Dynamic IP via DHCP Static IP O ADSL Virtual Dial up via PPPoE 121P O PPTP Back 34 Tenda W150M 150Mbps Wireless AP gt Static IP If your ISP provides you the Static IP please select Static IP access way You should input the IP address Subnet Mask Gateway DNS sever and the secondary DNS sever provided by your ISP then click Next Back Next gt ADSL Virtual Dial up via PPPoE If your ISP provides you the ADSL Virtual Dial up via PPPoE please select ADSL Virtual Dial up via PPPoE access way Enter the Account and Password provided by your ISP and click Next If you are not clear please consult your ISP If the Account is pppoe_user and Password is pppoe_passwd you need to enter the information as the diagram below Please enter the Account and Password provided by your ISP 35
30. ase put the device in the middle of wireless coverage area 1 Power Supply Please use the included power adapter to power on the Router IMPORTANT Use of a different power adapter could cause damage and void the warranty for this product 1 Network Configuration A Connect the LAN port of the Router to the computer with an Ethernet cable as below Tenda W150M 150Mbps Wireless AP B If you use wireless network adapter to access the internet the topology diagram is as below D YY T NR Wireless network connection a On your computer desktop right click My Network Places and select Properties LAN or High Speed Internet oa Local Area Connection 3 Px wireless Network Connection 2 Connected Not connected g P care Connec Tafa Intel R PRO 100 VE Netwo L_ 8 802 11n USB Wireless LAN b Right click Wireless Network Connection and select View Available Wireless Network The entire wireless signal will be shown in the interface Please select Tenda If you don t find it please click Refresh Network List 11 OF neds Metweed Cotten bon I Tenda W150M 150Mbps Wireless AP g ene Choose a wireless network One koord en tenk oT nga w tpt ox al tadaa n i x ve etset vill p Tesda Pete C Click Connect button 12 Tenda W150M 150Mbps Wireless AP Chapter 3 Working Mod
31. c IP WAN Settings WAN connection mode Static IP IP Address 192 168 1 2 Netmask 255 255 255 0 Gateway 192 168 1 1 DNS 202 986 134 133 Server Secondary DNS 202 90 120 68 optional Server MTU 1500 Do NOT Modify Unless Necessary If your connection mode is static IP you can modify the following addressing information lt IP Address Here enter the WAN IP address provided by your ISP If you are not clear consult you ISP please lt Subnet Mask Enter the subnet mask provided by your ISP Generally it is 255 255 255 0 lt Gateway Enter the WAN Gateway here If you are not certain please consult your local ISP lt Primary DNS Server Enter the Primary DNS server provided by your ISP lt Secondary DNS Server Enter the secondary DNS 6 3 MAC Address Clone This page is for the Router s MAC address to WAN Only in WISP mode and Wireless Router mode 44 Tenda W150M 150Mbps Wireless AP MAC Address Clone WAN MAC Address Clone MAC Address 00 80 2C 01 02 15 Restore Default MAC Clone MAC Address Apply Cancel Some ISPs require end user s MAC address binding to access their network ISP will provide a valid MAC address and you should input MAC address and save the configuration lt MAC Address The MAC address to be registered with your Internet service provider lt Clone MAC Address Register
32. e Wireless Security Settings 802 11n only defines three standard encryption methods Open None Disable WPA Personal AES WPA2 Personal AES Other encryption methods are nonstandard There may be compatibility problems among different manufacturers Apply Cancel gt WPA Algorithms Provides TKIP Temporal Key Integrity Protocol or AES Advanced Encryption Standard gt Pass Phrase Enter the encrypted characters with 8 63 ASCII characters gt Key Renewal Interval Set the key s renewal period 7 2 2 WPA2 personal WPA2 Wi Fi Protected Access version 2 provides higher security than WEP Wireless Equivalent Privacy or WPA Wi Fi Protected Access Besides TKIP encryption new AES encryption mode is provided 50 Tenda W150M 150Mbps Wireless AP Security Settings SSID Tenda Security Mode WPA Algorithms Pass Phrase Key Renewal Interval Notice Wireless Security Settings 802 11n only defines three standard encryption methods Open None Disable WPA Personal AES WPA2 Personal AES Other encryption methods are nonstandard There may be compatibility problems among different manufacturers Apply Cancel WPA2 Personal x AES OTKIP OTKIP amp AES 12345678 3600 second lt WPA Algorithms Provides TKIP Temporal Key Integrity Protocol or AES Advanced Encryption Standard lt Pass Phrase Enter the encrypted characters with 8 63
33. e device to access BSSID Basic Service Set Identifier of wireless network In 32 Tenda W150M 150Mbps Wireless AP IEEE802 11 BSSID is the MAC address of wireless access point lt Extend Channel To increase data throughput of wireless network the extension channel range is used in 11n mode lt V Channel Bandwidth Select the channel bandwidth to improve the wireless performance When the network has 11b g and 11n clients you can select the 40M when it is an 11n network select 20 40M to improve its throughput Click Next to save configurations Note We suggest you do not change the channel in this mode or else you can not access the device which you want to connect For wireless network encryption please refer to 7 2 Set the computer to Obtain IP address automatically to access the internet More details refer to Appendix I 5 5 Wireless Router Mode In this mode the device can connect to the DSL modem Cable modem such broadband devices or the broadband cable directly Note In this mode the LAN WAN port is worked as the WAN port After it takes effect only the computers with wireless network adapter can access the web based interface of the router Log on the web based interface as chapter 4 and then configure the mode as below 33 Tenda W150M 150Mbps Wireless AP 5 5 1 Select Wireless Router click Setup Wizard and Next button 5 5 2 Configure the p
34. e four configured keys as the current available 7 3 Advanced Settings This section is to configure the advanced wireless setting of the Router including the BG Protection Mode Basic Data Rates Fragmentation Threshold RTS Threshold and WMM etc 52 Tenda W150M 150Mbps Wireless AP Advanced Settings BG Protection Mode Auto Basic Data Rates Default 1 2 5 5 11 Mbps v Beacon Interval 100 ms range 20 999 default 100 Fragment Threshold 2346 RTS Threshold 2347 TX Power 100 range 1 100 default 100 WMM Capable Enbke O Disable APSD Capable OEnble Disable Apply Cancel lt BG protection Mode Auto by default It is for 11b g wireless client to connect lln wireless network smoothly in a complicated wireless area lt Basic Data Rates For different requirement you can select one of the suitable Basic Data Rates Here default value is 1 2 5 5 11Mbps It is recommended not to modify this value lt Beacon Interval Set the beacon interval of wireless radio Default value is 100 It is recommended not to modify this value Fragment Threshold The fragmentation threshold defines the maximum transmission packet size in bytes The packet will be fragmented if the arrival is bigger than the threshold setting The default size is 2346 bytes It is recommended not to modify this value lt RTS Threshold RTS stands for Request to send This 53 Tenda W150M 150
35. efault is disable WPS mode PBC Push Button Configuration and PIN code PBC Select the PBC or press the WPS button on the back panel of the device for about one second Press the button for about one second and WPS indicator will be blinking for 2 minutes which means the WPS is enabled Two minutes later the WPS indicator will be off which means the WPS connection is completed If more clients are added repeat the above steps At present the WPS supports up to 32 clients access PIN If this option is enabled you need to enter a wireless client s PIN code in the field and keep the same code in the WPS client WPS Summary Show the current state of Wi Fi protected setting including authorized mode encryption type default 55 Tenda W150M 150Mbps Wireless AP lt gt key and other information WPS Current Status Idle means WPS in idle state Start MSC process means the process has been started and waits for being connected Configured means the negotiation is successful between server and clients WPS Configured yes means WPS feature is enabled and goes into effect Not used means it is not used Usually the AP security has been enabled here will displayed not used WPS SSID Show the main SSID set by WPS WPS Auth Mode The authorization mode deployed by WPS generally WPA WPA2 personal mode WPS Encrypt Type The encryption type used by WPS generally AES TKIP WPS key The effective
36. ehavior of the computers in LAN you can enable client filter to control some ports access to Internet Client Filter Client Filtering Settings VI Access Policy 10 M Enable V Delete the Policy Clear C Disable Filtering Mode access the Internet Enable Policy Name 100 Start IP 192 168 2 100 End IP 192 168 2 100 Port 80 Mao Type TCP v Times 9 mlio y 18 0 v Date Everyday Sun Mon Tue Wen Thr Fri Sat Apply Cancel Client filter Select it to enable client filter Access Policy Select one number from the drop down menu Enable Check to enable the access policy gt gt Filter Mode Click one radio button to enable or disable to access the Internet Every rule is applicable only to the corresponding MAC address 66 Tenda W150M 150Mbps Wireless AP Policy Name Enter a name for the access policy selected lt v IP Start End Enter the starting ending IP address lt Port Enter the port range based over the protocol for access policy lt Type Select one protocol TCP UDP Both from the drop down menu lt Times Select the time range of client filter lt Date Select the day s to run the access policy lt If you don t want the computer at the IP address of 192 168 2 100 to access the Internet from 9 00 to 18 00 eve
37. es Introduction This device has five working modes You can change the modes depending on the applications This chapter will introduce every mode in details The default mode is AP access point mode 3 1 AP mode In this default mode the device worked as a converter between the wired and wireless signal is in default settings If you already have a wired router in use you can choose wireless AP mode Connect LAN port of the device to the router in use with an Ethernet cable refer to 5 1 for detail setup Then many wireless clients generally the wireless network adapter can access at the same time For example in a big hotel connect the Router to the broadband access port with the Ethernet cable and you can share the internet with others Of course your wireless network adapter must have the same SSID Channel with the Router If the Router enables Wi Fi protection the wireless network adapter also must have the same security mode and key to access the router Common network connection topology is as follows Tenda W150M 150Mbps Wireless AP Internet 2 amp i 3 2 Client AP Mode In this mode the device can receive the wireless signal meanwhile amplify the signal and extend the wireless signal coverage The wired device can receive the signal via the Ethernet cable This mode is called the wireless signal universal repeater mode which can amplify the source signal to enhance the signal When you share
38. ess AP T a moser mr j WDHAP dose Piane ick Narr wed covfigary the device step by step 5 3 2 Configure the parameters WDS Setting APMAC 00 80 2c 01 89 00 APMAC 00 80 0 03 c4 02 AP MAC 00 Oc 43 30 52 88 AP MAC Channel 6 Eeceypt Type NONE r Disable Scan Steveity Signal NONE X 1 WPAIPSKWPAIPSKTRIPAES 5 NONE v NONE WPAPSK TRIP 5 nmin are AP MAC Address Input the MAC address of the terminal wireless device Wireless MAC address also can be named 27 Tenda W150M 150Mbps Wireless AP as BSSID The terminal wireless device can be an AP with WDS function or a wireless router lt Channel Specify the effective channel from I to 13 Auto of the wireless network The channel you set must be the same as the terminal device lt Encrypt Type The encrypt type security mode you set should be the same as the terminal device More details please refer to the Wireless Security Settings chapter We recommend you Scan the access points and then select the SSID in your scanned SSID list for convenience Click Next to the following interface 5 3 3 Wireless Basic Setting SSD Tenda ant Disable Enable Back Next Network Mode Select one mode from the following The default is 11b g n mode 11b mode Allow the wireless client to connect with the device in 11b mode at the maximum speed of 11 Mbps 11g mode Allow the 11g 11n compliant client device to connect
39. ess as 218 88 93 33 218 88 93 35 then only the IP addresses as 218 88 93 33 218 88 93 34 and 218 88 93 35 can access the Router 71 Tenda W150M 150Mbps Wireless AP For example If you want to configure the IP address 218 88 93 33 to access the device s web interface please set it as above 10 6 WAN Ping The ping test is to check the status of your internet connection When disabling the test the system will ignore the ping test from WAN WAN Ping Ignore the Ping from WAN v lt Ignore the Ping from WAN Check to ignore the ping request and give no reply 72 Tenda W150M 150Mbps Wireless AP Chapter 11 Routing setting 11 1 Routing Table This page shows the primary routing table Destination IP Subnet Mask Gateway Metric Interface bro bro bro Refresh The main duty for a router is to look for a best path for every data frame and transfer this data frame to the destination So it s essential for the router to choose the best path i e routing arithmetic In order to finish this function many transferring paths i e routing table are saved in the router for choosing when needed 73 Tenda W150M 150Mbps Wireless AP Chapter 12 System Tools 12 1 Time Settings This section is to select the time zone for your location If you turn off the Router the settings for time disappear However the Router will automatically obtain
40. et can be useful some files can potentially harm your computer If you do not trust the source do not open or save this file what s the risk Click Save to save the configuration files gt Restore Setting Click Browse button to select the backup files Choose file Look in 2 Desktop my Documents my Computer E My Network Places fl adobe Reader 7 0 Da files Desktop ha Hypersnap E New Folder 12 My Documents My Computer bd jetwork File name Files of type Routerctm cfg 285 Shortcut to Hprsnap All Files v Click Restore button to restore previous settings 77 Tenda W150M 150Mbps Wireless AP Backup Restore The device provides backup restore settings so you need set a directory to keep these parameters Backup Please choose restore file CADocuments and Settl Browse 12 4 Restore to Factory Default Setting This button is to reset all settings to the default values It means the Router will lose all the settings you have set So please Note down the related settings if necessary Restore to Factory Default Settings Restore to Factory Default Settings Restore gt Restore Click this button to restore to default settings lt gt Factory Default Settings User Name admin Password admin IP Address 192 168 2 1 Subnet Mask 255 255 255 0 Note Afte
41. ing gt connection status to enter the following screen 37 Tenda W150M 150Mbps Wireless AP Wireless Connection Status The Current Wireless Access List NO MAC Address Bandwidth 0 00 50 43 00 00 05 40M lt MAC Address Shows current MAC addresses of the hosts connecting to the Router lt Bandwidth Shows current frequency bandwidth the wireless client used 58 Tenda W150M 150Mbps Wireless AP Chapter 8 DHCP Server DHCP server is for the WISP mode and wireless Router mode 8 1 DHCP Settings DHCP Dynamic Host Control Protocol is to assign an IP address to the computers on the LAN private network When you enable the DHCP Server the DHCP Server will allocate automatically an unused IP address from the IP address pool to the requesting computer in premise of activating Obtain an IP Address Automatically So specifying the starting and ending address of the IP Address pool is needed DHCP Server DHCP Server Y Enable IP Address Start 192 168 2 100 IP Address End 192 168 2 200 Lease Time One day v Apply Cancel DHCP Server Activate the checkbox to enable DHCP server lt IP Address Start Enter the range of IP address pool for DHCP server distribution lt IP Address End Enter the range of IP address pool for DHCP server distribution 59 Tenda W150M 150Mbps Wireless AP lt Lease Time The
42. length of the IP address lease Set an appropriate lease time to improve the recovery efficiency of invalid IP address For example If the lease time is an hour then DHCP server will reclaim the IP address each hour 8 2 DHCP List and Binding DHCP client can display computers IP address MAC address host name and other information which are assigned by the DHCP sever You can manually enter the IP and MAC address it would be converted to static allocation According to the computer s MAC address DHCP will assign the appropriate IP address If you can not find the corresponding static binding entry assign an IP from the DHCP pool to the computer If the computer had been bound for the IP address and MAC and they do not correspond then the computer will be unable to access equipment Through binding prevents unauthorized to change the client IP address and to evade the monitoring device 60 Tenda W150M 150Mbps Wireless AP DHCP List amp Binding Static IP IP Address 192 168 2 100 MAC Address 00 B0 8C O07 19 F4 Add NO IP Address MAC Address IP MAC bind Delete 1 192 168 2 100 00 B0 8C 07 19 F4 v Delete Refresh Host Name IP Address MAC Address Lease lt IP Address Enter the IP address which needs to be bound lt MAC Address Enter the MAC address of the computer you want to assign the above IP address
43. less AP N md WLAN ap pr 9 gt More details please refer to 5 4 3 5 Wireless Router Mode In this mode the device can be worked as the router with wireless NAT function and DHCP sever The laptops can get IP addresses automatically which assigned by the DHCP sever When the RJ45 port connects to the broadband access the laptops can share the internet at the same time The topology is as follows Internet 4 CABLE DSL MODEM pe qe gt m More details please refer to 5 5 Tenda f W150M 150Mbps Wireless AP Chapter 4 How to login to the Router The chapter mainly presents how to enter the Router s Web interface After you have finished the hardware installation Please refer to chapter2 the following steps will assist you to set the network configurations for you computer 4 1 How to Set the Wired Network Configurations 4 1 1 On your computer desktop right click My Network Places and select Properties take Windows XP as an example A My Documents My Computer Open My Met Explore Search for Computers Map Network Drive Disconnect Network Drive Create Shortcut Delete Rename Properties 4 1 2 Right click Local Area Network Connection and select Properties If you enable the wireless connection please select Wireless Network Connection Tenda W150M 150Mbps Wireless AP 4 1 3 Select I
44. list for convenience Click Next to the following interface 5 2 3 Wireless Basic Setting Wireless Basic Setting Network Mode 11b g n mixed mode v SSID Tenda Broadcast SSID Enable Disable Channel 2437MHz Channel 6 nt Disable Ende 2417MHz Channel 2 A Disable Enable Back Next 24 Tenda W150M 150Mbps Wireless AP gt Network Mode Select one mode from the following The default is 11b g n mode 11b mode Allow the wireless client to connect with the device in 11b mode at the maximum speed of 11 Mbps 11g mode Allow the 11g 11n compliant client device to connect with the AP at the maximum speed of 54Mbps 11b g mode Allow the 11b g compliant client device to connect with the AP with auto negotiation speed and lin wireless client to connect the device with 11g speed 11b g n mode Allow 11b g n compliant client device to connect gt with the AP with auto negotiation speed SSID SSID Service Set Identifier is the unique name of the wireless network Wireless client must input the same SSID to access Channel Specify the effective channel from 1 to 13VAuto of the wireless network Broadcast SSID Select Disable to disable the device s SSID to be invisible by the wireless client If you disable it client must input the same SSID as the device to access BSSID Basic Service Set Identifier of wireless network In IEEE802 11 BSSID
45. nd click Properties 4 Local Area Connection Properties EG _ General Advanced Connect using E9 Realtek ATL8139 Family PCI Fast Ett This connection uses the following items mia 7 MI dE 00S Packet Scheduler f l I EEE 802 1x v3 5 3 0 i e oe a ee Install rinstal Description Transmission Control Protocol Internet Protocol The default wide area network protocol that provides communication across diverse interconnected networks J Show icon in notification area when connected 7 Notify me when this connection has limited or no connectivity Cx 4 Select Obtain an IP address automatically 83 Tenda W150M 150Mbps Wireless AP 5 Select Status within Local Area Connection click support Internet Protocol TCP IP Properties General Alternate Configuration You can get IP settings assigned automatically if your network supports this capabilly Otherwise you need to ask your network administrator for the appropriate IP settings Obtain an IP address automatically Use the following IP address Obtain DNS server address automatically Use the following DNS server addresses Iternate DN E dialog box you can see whether you have got the IP sh Local Area tion tatu Jeg General Support Connection status al Address Type
46. nda W150M 150Mbps Wireless AP need to configure the signal transmitter but only to simply configure the W150M to amplify the wireless signal and multi computers can share the internet This mode is mainly used in hotspot access The fifth mode is Wireless Router mode Use this mode to form a local network that has both broadband connections via broadband access cable and wireless access This mode can apply to various broadband access environments including ADSL Cable TV Networks Having wireless AP and wireless Router function W150M is equipped with a Mode button to switch the modes to achieve different wireless access In addition the device can be powered by an alternative power supply through the USB port to establish wireless networks freely The W150M is a solid choice for people with always moving network needs in search of a fast secure easy to use and feature rich wireless network 1 2 Products Features gt Comply with IEEE 802 11n IEEE 802 11g IEEE 802 11b IEEE 802 3 and IEEE 802 3u standards gt Adopts IEEE 802 11n advanced technology and built in high performance antennas with 3 times wireless coverage of 54M products gt 150Mbps wireless transmission rate gt Support AP mode Client AP mode WDS AP mode WISP Tenda W150M 150Mbps Wireless AP Vv Vv VV v Y mode Wireless Router mode Support 64 128 bit WEP WPA WPA2 encryption WPS PBC and PIN enabled device Provides one 10
47. nnection Mode It shows the current connection method lt Account Input the user name provided by your ISP 42 Tenda W150M 150Mbps Wireless AP lt gt lt gt lt gt Password Enter the password provided by your ISP MTU Maximum Transmission Unit It is the size of largest datagram that can be sent over a network The default value is 1492 Do NOT modify it unless necessary But if some specific website or web application software can not be open or enabled you can have a try to change the MTU value as 1450 1400 etc Service Name It is defined as a set of characteristics that are applied to a PPPoE connection Enter it if provided Do NOT modify it unless necessary AC Name Enter it if provided Do NOT modify it unless necessary Connect Automatically Connect automatically to the Internet after rebooting the system or connection failure Connect Manually Connect to the Internet by users manually Connect on Demand Re establish your connection to the Internet after the specific time Max Idle Time Zero means your Internet connection at all time Otherwise enter the minutes to be elapsed before you want to disconnect the Internet access Connect on Fixed Time Connect to the Internet during the time you fix Notice The Connect on Fixed Time can be deployed only when you have set the current time in Time Settings from System Tools 43 Tenda W150M 150Mbps Wireless AP 6 2 2Stati
48. nssnssen 87 APPENDIXIV TROUBLESHOOTING sssovosvevevevssnnnessssevenssnssee 89 Tenda W150M 150Mbps Wireless AP Chapter 1 Product overview 1 1 Production introduction Thank you for purchasing the Tenda W150M 150Mbps Wireless AP W150M is a portable wireless AP Router with up to 150Mbps transmission rate It supports five working modes wireless AP access point Client AP WDS AP WISP Router and Wireless Router The default mode is wireless AP access point in this mode the device can convert wireless and wired signals For example in a hotel you want to share the internet with others there is no need to set the router the things you need to do is to connect the router to the broadband access point and configure computers to obtain an IP address and DNS automatically The second mode is the Client AP mode In this mode the router can repeat and amplify the wireless signals while at the same time transmitting and receiving data on RJ45 port Enable this mode to enhance the wireless signal when you and your neighbor share the internet you can get the amplified and stable signal This mode also can be used in broadband satellite receiver access The third mode is WDS AP mode In this mode you can bridge two local area networks or two computers and meanwhile amplify and transfer the signals This mode is used for many devices wireless bridge and repeat The forth mode is WISP Router mode In this mode you do not Te
49. nter to Confirm Re enter to confirm the new password Note It is highly recommended to change the user name and password to secure your network and the Router 80 Tenda W150M 150Mbps Wireless AP 12 8 System Log The section is to view the system log Click the Refresh to update the log Click Clear to clear all shown information If the log is over 150 records it will clear them automatically GI EIBIBNSTSNT STE 0 0 Refresh Clear gt Refresh Click this button to update the log gt Clear Click this button to clear the current shown log 12 9 Logout After you have finished the settings completely in logout page click Yes to logout the web management page 81 Tenda W150M 150Mbps Wireless AP Appendix I How to Obtain an IP Automatically If you enable DHCP default you can get the IP address Gateway DNS automatically to access the internet Please set you device as below 1 On your computer desktop right click My Network Places and select Properties Explore Search for Computers Map Network Drive Disconnect Network Drive Create Shortcut Delete Rename 2 Right click Local Area Network Connection and select Properties If you use wireless connection please click Wireless Network Connection 82 Tenda W150M 150Mbps Wireless AP 3 Select Internet Protocol TCP IP a
50. nternet Protocol TCP IP and click Properties Local Area Connection Properties 218 General Advanced Connect using E9 Realtek RTL8139 Family PCI Fast Ett This connection uses the following items E 005 Packet Scheduler a F AEGIS Protocol IEEE 802 1x v3 5 3 0 M rintamet Protocol TCP IP el s m Install Uninstall Leafy aad Description Transmission Control Protocol Interet Protocol The default wide area network protocol that provides communication across diverse interconnected networks K Show icon in notification area when connected Notify me when this connection has limited or no connectivity lt OK Cancel 19 Tenda W150M 150Mbps Wireless AP 4 1 4 Select Using the following IP address and input the IP address IP address 192 168 2 XXX XXX is a number from 2 254 Internet Protocol TCP IP Properties Ax General You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for the appropriate IP settings Obtain an IP address automatically Use the following IP address IP address 192 168 2 200 Subnet mask 255 255 265 0 Default gateway Use the following DNS server addresses Preferred DNS server Altemate DNS server Ce 4 2 Login to
51. o 7 2 29 Tenda W150M 150Mbps Wireless AP After configuration complete the AP works as a wireless signal repeater You can connect the device to computer satellite receiver and IPTV set top box and you need to set them to obtain IP address automatically to access the source wireless device source wireless router Detailed settings refer to the Appendix I 5 4 WISP Mode Log on the web based interface as chapter 4 and then configure the mode as below 5 4 1 Select WISP click Setup Wizard and Next button 5 4 2 Configure the parameters WISP Setting SSD MAC Channel Security Mode Back Next Tenda11347 00 10 18 01 02 24 13 v NONE v SSID SSID Service Set Identifier is the unique name of 30 Tenda W150M 150Mbps Wireless AP lt gt the wireless network Input the SSID of the aimed AP MAC Address The Router s physical MAC address as seen on your local network is unchangeable Input the MAC address of the AP you want to choose Sometimes MAC address is also named BSSID BSSID Basic Service Set Identifier of wireless network In IEEE802 11 BSSID is the MAC address of wireless access point Channel Specify the effective channel from 1 to 13 Auto of the wireless network The channel you select must be correspondence with the AP provided by your ISP Security Mode The security mode you set should be the same as the
52. ou need to set it as above 10 4 Prevent Network Attack This section is to protect the internal network from exotic attack such as SYN Flooding attack Smurf attack LAND attack etc Once detecting the unknown attack the Router will restrict its bandwidth automatically The attacker s IP address can be found from the System Log lt Prevent Network Attack Enable it for attack prevention Prevent Network Attack Prevent Network Attack Cancel 70 Tenda W150M 150Mbps Wireless AP 10 5 Remote WEB Management This section is to allow the network administrator to manage the Router remotely If you want to access the Router from outside of the local network please select the Enable Remote WEB Management Enable v Port 8080 WAN IP Address 218 88 93 33 218 88 93 33 Apply Cancel lt Enable Check to enable remote web management gt Port The management port open to outside access lt WAN IP Address Specify the range of the WAN IP address for remote management Note 1 If you want to login to the Web based interface via port 8080 you need use the format of WAN IP address port for example http 220 135 211 56 8080 to implement remote login 2 If your WAN IP address starts and ends with 0 0 0 0 it means all hosts in WAN can implement remote Web management If you change the WAN IP addr
53. ough If it can scan too many wireless signals we recommend you to use I 1b g mode for reducing interference Please make sure that the needed parameters such as SSID MAC address etc are correct It is recommended to use Auto Scan to finish the settings in the setup process Please make sure that IP address range obtained at WAN port are 92 Tenda W150M 150Mbps Wireless AP different as the one obtained at LAN port If they are at the same range you can modify the LAN IP address to solve the problem d Please do not detach any antenna of the wireless Router when you are using the Router After trying all the above steps if you still can t access the Internet you can contact us for support If you still have some problems please contact our customer service or log on our website Tenda website http www tenda cn Technical Support Toll Free 400 6622 666 For Mainland China Only Toll Free 1 800 570 5892 For USA only Tel 86 755 2344 2820 Skype tendasz MSN tendasz hotmail com Email support tenda com cn Headquarter Shenzhen Add Tenda Industrial Zone No 34 1 Shilong Road Shiyan Town Baoan District Shenzhen China 518108 Tel 86 755 27657180 Fax 86 755 27657178 Email sales tenda com cn Technical Support support tenda com cn Integrated Wiring Division Department 93 Tenda W150M 150Mbps Wireless AP Add Al2E The first world square 7002 Hongli west road Futian Shenzhen Tel
54. punminsikkegne RA eee de Gain ee 45 CHAPTER 7 WIRELESS SETTING soseovevveveevevsvvevevsveesensesessens 47 Tal Basic Settings sos hjernen anime s 47 7 2 Wireless Security Setting srsnrrnrrrrnvrnrrvrnrrnnrvnnrrnnsennrrnnsenenne 49 7 3 Advanced Settings rrsnrrnrrsvenrrrvrrnrrnrrnrrnnrnvennrsrernrenssnerssrnnensenne 52 7 4 WPS Settings srorronrrnrrnvrnrrerennrsnrrnersrenernnrsrensrsvesnersssnerssrsrensenne 54 7 5 Wireless Access Control nnnranrnvrrnrrnrrnnrsrennrsvernrrnrenernsrsrennrnne 56 7 6 Connection Status cccccccccccesessesseessesessecsessecseessesseeeeeseesesaeens 57 CHAPTER 8 DHCP SERVER ssessoseovevsevvevevseveevensevesvensesessensssessens 59 8 1 DHCP Settings srrrsrrnrrsrenrrevernrrsrrnernrrnvensrsversrsnessersssnsensrereneer 59 8 2 DHCP List and Binding eserororvrrvrrnvrnrrnvenrrsversrenesversrenssesrsrenne 60 CHAPTER 9 VIRTUAL SERVER esessevvevevsevenvevsvenvevsssensensssensens 62 9 1 Port Range Forwarding ronenvrovrrnrrnrrnvrnnrsrennrsvernrrsrenersrssensrnne 62 92 DMZ Settings svr seminarene isens 63 9 3 UPnP Settings oc cccccesccscesscsseseceseeecssecseesecseceeesseeeeeseesenaeens 64 CHAPTER 10 SECURITY SETTINGS ssesseveevevseveevevseveesensevessens 66 10 1 Client Filter Settings msrenrrororvrrnrenvrnrrsrenrrsvernrrnrsnrrssrsvensenne 66 10 2 URL Filter Settings srsnroronvrorrrvrrnrenvrnnrsrenrrsvernernssnerssrsvensenne 67 10 3 MAC Address Filter soronenoronornrrnrenrrn
55. r restoring to default settings please restart the device then the default settings can go into effect 78 Tenda W150M 150Mbps Wireless AP 12 5 Upgrade The Router provides the firmware upgrade by clicking the Upgrade after browsing the firmware upgrade packet which you can download from www tenda cn IMPORTANT Do not power off the brenne Vie firmus rede to ivori damagag the device The meter ul boot after the upgrade gt Browse click this button to select the upgrade file gt Upgrade click this button to start the upgrading process After the upgrade is completed the Router will reboot automatically Note Do not power off the device during the upgrade 12 6 Reboot the Router Rebooting the Router makes the settings configured go into effect After it is rebooted the WAN port connection will be unconnected automatically 79 Tenda W150M 150Mbps Wireless AP Reboot Click here to reboot the router 10 Reboot the router Click this button to reboot the device 12 7 Change Password This section is to set a new user name and password to better secure your router and network Change Passw Note User Name and Password makeup only by number or and letter User Name admin User Name Enter a new user name for the device Old Password Enter the old password New Password Enter a new password VV v WV Re e
56. rent tom p uM SN t fo p ome tr gt 4 Connected will be shown in the interface as the following diagram ti Choose a wireless network akan man i tha be bilon to connect to a yareincs network in ranga oF to gat more Tenda Connected y Urseaued wireless network ull wireless test te Urseosed wireless network vill P Mobedata_n Urconured wirkers network will ep Tonda Publ Of saaaty an sind varsles rater WPA will p Tenda aranan ngne id wrens netwerk will of Salaye securty ensbled sareiess network will 86 Tenda W150M 150Mbps Wireless AP Appendix III Glossary Channel An instance of medium use for the purpose of passing protocol data units PDU that may be used simultaneously in the same volume of space with other instances of medium use on other channels by other instances of the same physical layer PHY with an acceptably low frame error ratio FER due to mutual interference SSID It is the short of Service Set Identifier An SSID is the network name shared by all devices in a wireless network Your network s SSID should be unique to your network and identical for all devices within the network It is case sensitive and must not exceed 20 characters use any of the characters on the keyboard Make sure this setting is the same for all devices in your wireless network WEP Wired Equivalent Privacy WEP is the method for secure wireless data tr
57. rrrvnrsvrrrrvrnrsrvrrssvnssvresssvesenree 10 CHAPTER 3 WORKING MODES INTRODUCTION 13 SLAP mode sunneste ie 13 3 2 Client AP Mode rmmrsarsvvversrersvverrsrersvvvrssrrssvverssrnvsvvesssrnssvvenee 14 3 3 WDS AP Mode vrenn en TE EEE E E REK 15 3 4 WISP Mode nerverevrorrsersverssrrssvvnnssrrssvvenssrrssvvenssvnssvvenssvessvvenee 16 3 5 Wireless Router Mode rrmnrsrnrannnssvnnsnvnnssvrssvvenssrnvsvvenssrsssvvenee 17 CHAPTER 4 HOW TO LOGIN TO THE ROUTER 0 18 4 1 How to Set the Wired Network Configurations 00 18 4 2 Login to the Web Interface ummeenenrrvrnerrrrrrrerrrrrrrererserrerenn 20 CHAPTER 5 WORKING MODES SETUP WIZARD 00 22 SLAP MO 22 52 G UT 15900 ENES Eei 23 5 2 3 Wireless Basic Setting s mssorvrrvrrnrrrrsrervrrrernrrnrsnersrrsrensrnne 24 5 2 4 Wireless Security Settings ssrrrrnrrnrrsrenvrrvrrnrrnrenrrrrsrennrnne 26 5 3 WDS AP Mode Setup Wizard sesnernnrrnnvrnnrvnvernnrvsnrrnnsenenne 27 54 WISP Mode unna 30 5 5 Wireless Router Mode rmmrsvarsvvnrrsrarsvvversrrrsvverssvevevvesssrnssvvenee 33 CHAPTER 6 ADVANCED SETTINGS sevesvessvessvessvesnessnessnesneee 40 6 1 LAN Settings csc daisies dein nee RNR aie 40 6 2 WAN Settings occ ec cccccccesecsseescsseeeceseeseesecsessecseeeeenseeeesseeneeaeens 42 Tenda W150M 150Mbps Wireless AP 6 3 MAC Address Clone rsrrnrrorenvrsvrrnrrnrsnrrnnrsrersrsvernernssnerssrsrensrnne 44 6 4 DNS Settings vu s
58. rrsrenvrsvernernrsnersrsrennenne 69 10 4 Prevent Network Attack rrorornrrnrrnrrnrrorenrrsvernrrnrsnerssrsrennenne 70 10 5 Remote WEB Management eonrrnronrrnnrorennrsnernernrenrrssrerennrnne 71 10 6 WAN Ping ccairt eE E E EEE ER 72 CHAPTER 11 ROUTING SETTING nssoovevveveevevseveevevsevessensesensens 73 IM ROUTING TABLE see 73 CHAPTER 12 SYSTEM TOOLS sssovessevesvevsevenvenssvensenssensensssensens 74 12 1 Time Settings rosnrrnrrnrrnrrvrenrrsnrrnrrsrenrrnsrsresrsnersersssnerssrsrensenne 74 12 2 DDN S i igenenmriinerinnriierindarnindaririierie arti 74 12 3 Backup Restore Settings rmsrrvrrnrrnrrrrrerenvrsvernrrnrrnrrsrsrennenne 76 12 4 Restore to Factory Default Setting soennrrrnnrrnnrrnrrrnrrrnenne 78 Tenda W150M 150Mbps Wireless AP 12 5 Up r d sutsesenenmesngegror eda unseantden tt 79 12 6 Reboot the Router c cisccsisccsccscossscosiocdsconcostscencocdnconceaveeesdodene 79 12 7 Change Password rrrsrrnnrorenvrsvrrnernrenrrnnrsrensrsnersersrsnerssssrensenne 80 12 8 System Log renrrnnernrrrnvernnvsnernrrennernrnesnernrsennerenseneernsseneerensenenn 81 12 9 LOB OUbs sanne E E E A A A E 81 APPENDIX I HOW TO OBTAIN AN IP AUTOMATICALLY ssscssssssssssecssscaieciscerssssascstecsisetbccisstasessisvisieiuses 82 APPENDIX II HOW TO SET THE NETWORK CARD AFTER DEVICE ENCRYPTED sesosoovevessvnvevensvnesvesssnessenssnessensee 85 APPENDIX II GLOSSARY ssevesevsevevessevevevsenenensssenenssssvensssene
59. ryday without restrictions to other computers in LAN you need to set the packet filtering list as the above diagram 10 2 URL Filter Settings In order to control the computer to access to websites you can use URL filtering to allow the computer to have access to certain websites at fixed time and forbids it having access to certain websites at fixed time 67 Tenda W150M 150Mbps Wireless AP VV v V v yv gt gt gt URL Filter Check to enable URL filter Access Policy Select one number from the drop down menu Enable Check to enable the access policy Filter Mode Click one radio button to enable or disable to access the Internet Policy Name Enter a name for the access policy selected Start End IP Enter the starting ending IP address URL Specify the text strings or keywords needed to be filtered If any part of the URL contains these strings or words the web page will not be accessible and displayed Times Select the time range of client filter Date Select the day s to run the access policy Apply Select Apply to enable the settings For example If you want the computer at the IP address of 192 168 2 123 to 68 Tenda W150M 150Mbps Wireless AP access the Internet from 9 00 to 18 00 everyday and only can search the WEB pages contain the strings such as sina sohu and yahoo you need to set the packet filtering list as the above diagram Notice different strings
60. s AP symbols for pass phrase Click Next to save the configuration More details please refer to the following chapter 5 5 5 Click Apply to save the settings and reboot the router to let the settings take effect Setup Wizard The configuration is completed Click Apply to activate your settings or press Back to change yor tings Back Apply Note Only the computers with wireless network adapter can access to the wireless router if the mode take effect and set the computer to obtain IP address automatically More details refer to Appendix II 39 Tenda W150M 150Mbps Wireless AP Chapter 6 Advanced Settings 6 1 LAN Settings This section will describe how to configure the TCP IP parameters 6 1 1 LAN settings in WISP and Wireless Router mode 192 168 2 1 255 255 255 0 Apply Cancel MAC Address The device s physical MAC address as seen on your local network is unchangeable lt IP Address The Router s LAN IP addresses not your PC s IP address 192 168 2 lis the default value Once you change it you need to use the new IP to access the router lt Subnet Mask It s shown the Router s subnet mask for measurement of the network size 255 255 255 0 is the default value 6 1 2 LAN settings in AP Client AP and WDS AP mode 40 Tenda W150M 150Mbps Wireless AP MAC Address The device s physical
61. s subject to the following two conditions 1 This device may not cause interference and 2 This device must accept any interference including interference that may cause undesired operation of the device Caution The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment Such modifications could void the user authority to operate the equipment 97
62. te radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected 96 Tenda W150M 150Mbps Wireless AP Consult the dealer or an experienced radio TV technician for help To assure continued compliance any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this equipment Example use only shielded interface cables when connecting to computer or peripheral devices The antenna s used for this transmitter must not be co located or operating in conjunction with any other antenna or transmitter FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment This equipment should be installed and operated with the minimum distance of 20 cm Operation i
63. the Web Interface After you set you computer as 4 1 you can follow the below steps to access the Router s web interface 4 2 1 To access the Router s Web based interface launch a web browser such as Internet Explorer and enter the Router s default IP address http 192 168 2 1 Press Enter http 192 168 2 1 4 2 2 Input the admin in both User Name and Password Click OK 20 Tenda W150M 150Mbps Wireless AP 150Mbps Portable Wireless AP Router User name admin Password sence V Remember my password a buen 4 2 3 If you enter the correct user name and password you can enter the router s web interface 21 Tenda W150M 150Mbps Wireless AP Chapter 5 Working Modes Setup Wizard 5 1 AP mode In this default mode the device can convert the wired and wireless signal which is the center access point for few clients generally wireless network adapter For example in a big hotel connect the Router to the broadband access port with the Ethernet cable and configure your computer to obtain an IP address automatically and then you can share the internet with others Generally the broadband Router of the hotel has DHCP function which can assign IP address for clients This section guides you how to connect wireless client to the access point we will guide you step by step Please connect the device as follows Internet gt my A
64. tive channel from I to 13 Auto of the wireless network lt Broadcast SSID Select Disable to disable the device s SSID to be invisible by the wireless client If you disable it client must input the same SSID as the device to access lt V BSSID Basic Service Set Identifier of wireless network In IEEE802 11 BSSID is the MAC address of wireless access point lt Extend Channel To increase data throughput of wireless 37 Tenda W150M 150Mbps Wireless AP network the extension channel range is used in 11n mode lt Channel Bandwidth Select the channel bandwidth to improve the wireless performance When the network has 11b g and 11n clients you can select the 40M when it is an I In network select 20 40M to improve its throughput Click Next to save configurations Note Generally you only need to change the wireless SSID wireless channel if you are not very sure of other parameters you can not configure them to avoid affecting wireless performance 5 5 4 Wireless Security Setting Security Mode WPA Personal ms AES TKIP TKIP amp AES PlsChangeMe Back Next You can select WEP WPA personal WPA2 personal and other security modes Note the parameters you set for wireless client access It is suggested that you choose WPA personal for Security Mode and AES for WPA Algorithms Input 8 63 numbers letters and 38 Tenda W150M 150Mbps Wireles

Download Pdf Manuals

Related Search

Related Contents

Excalibur electronic ABC Wide 334 User's Manual  OPERATING INSTRUCTIONS - cool-skk  Cables Direct B5-101B networking cable  MANUAL DE INSTRUCCIONES  取扱説明書  Da-Lite Advantage Deluxe Electrol  METS User Manual  ZyXEL P-662HW-D User's Manual  Sensory Science 7405 User's Manual  Télécharger - Plateforme Elsa  

Copyright © All rights reserved. Failed to retrieve file