Home

Chief K2C22HS flat panel desk mount

image

Contents

1. to secure array J1 to K2 arm A See Figure 10 NOTE Cable clip J11 can be used in place of pivot point spacer J12 if additional cable managementis desired See Figure 10 Figure 10 11 K2C Series Installation Instructions Display Installation non array versions NOTE K2C22H models have K1 Series faceplates on array arms Proceed to K2C22H Models Section The mounting holes on the back of the display will either be flush with the back surface or recessed into the back surface Refer to the applicable installation procedure WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of all components located between the K2C Series Monitor Arm up to and including the display does not exceed the weight limits listed below Use with products heavier than the maximum weight indicated may result in collapse of the mount and its accessories causing possible injury Max Weight Allowed for EACH Max Weight Capacity of Display Mounting System K2C110 22 Ibs 22 Ibs 9 98 kg 9 98 kg K2C120 22 Ibs 22 Ibs 9 98 kg 9 98 kg K2C220 22 Ibs 44 lbs 9 98 kg 19 96 kg een 22 105 22 Ibs 9 98 kg 9 98 kg K2C220SXF1 22 105 44 lbs 9 98 kg 19 96 kg K2C22H 9 Ibs 18 Ibs 4 08 kg 8 16 kg K2C22HSXF1 915 18 Ibs 4 08 kg 8 16 kg
2. 12 Flush Mounting Holes A CAUTION Using screws of improper size may damage your display Proper screws will easily and completely thread into display mounting holes A CAUTION Inadequate thread engagement in display may cause display to fall Back out screws ONLY as necessary to allow installation of Centris bracket 1 Ensure faceplate is able to swivel and tilt easily yet still be tight enough to hold display in desired position Adjust as required before proceeding See ADJUSTMENT for detail See Figure 11 2 Using Phillips screwdriver carefully install two M4x14mm screws B into the upper mounting holes on the display Thread screws completely into display then back out 3 complete turns See Figure 11 3 Pickup and align display so that screws B installed on the back of the display in the previous step fit into the mounting holes on the faceplate Rotate the bracket as required Lower the display firmly into place See Figure 11 4 Using Phillips screwdriver install two remaining M4x14mm Phillips screws B through the ower mounting holes in faceplate into the display See Figure 11 5 Tighten all four screws B Do not overtighten Installation Instructions K2C Series Recessed Mounting Holes 1 Ensure Centris bracket is able to swivel and tilt easily yet still be tight enough to hold display in desired position Adjust as required before proceed
3. 7 3 Hook back of mount base into back groove of Frame One rail See Figure 8 4 Place mountbase onto Frame One rail making sure holes line up with holes on channel plate K See Figure 8 5 Use two 10 32 x 7 8 flat head cap screws M to secure mount base to channel plate K See Figure 8 Figure 8 Installation Instructions K2C Series NOTE If mount leans forward after installation install one or two shims L in between mount base and rail as shown in the following steps Installing Shim Spacers if required IMPORTANT Do NOT install one or both shims L unless required as damage to the Frame One rail may result 6 Remove two 10 32 x 7 8 flat head cap screws holding mount base to channel plate K 7 Slide one or two shims L in between mount base and rail lining up holes on shim s with holes on plate and rail See Figure 9 8 Use two 10 32 x 7 8 flat head cap screws M to reinstall mount base to channel plate K See Figure 9 L x 1 or 2 if required Figure 9 Array Installation K2C22H and K2C22HSXF1 Models ONLY 1 Slide rotational spacer J10 into opening on array attachment bracket See Figure 10 Use 5 16 18 x 3 button head cap screw J3 two thin steel washers J8 plastic spacer J9 pocket washer J5 pivot pin J4 pivot point spacer J12 and 5 16 18 lock nut J6
4. 98 kg TA 22 105 44 lbs 9 98 kg 19 96 kg K2C22H 9 lbs 18 Ibs 4 08 kg 8 16 kg K2C22HSXF1 9 Ibs 18 Ibs 4 08 kg 8 16 kg Max Weight Allowed for EACH Display Max Weight Capacity of Mounting System SAVE THESE INSTRUCTIONS Installation Instructions K2C Series DIMENSIONS K2C110 2 32 WE V6 da EE IT E INTERFACE ROTATION RANGE EI MOUNTING COMPATIBIL 100 100 NTERFAC UP IBMT Vuen ADIUSTERNGE 19 26 ENT 81 I i3 US 4 i MOUNTING PATTERN CON TIBILITY e K2C Series K2C220 Installation Instructions SO Aye eo HO UE TIEG PATTERN Wielt ii AAA ENT MAN UALHEIG HT ADJUSTRANGE 19 24 4 it 114 i 1 DESKTOP THICKNESS Es 11 i K2C120SXF1 ES 3 52 6 75 6 75 131 89 4 171 5 171 5 54 0 INTERFACE ROTATION RANGE Hi T
5. ILT RANG E j 157 157000 4 PATTERN COW PATIBILIY Ur Le 7 2 1 HANVALKEIGET QE UU nur 19 1223 a 488 4 310 6 n 1 69 Installation Instructions K2C Series K2C220SXF1 MOUNTING PATTERN COMPATIBILITY TILT RANGE 11 15 1 IS 2 He 1 TILT RANGE 0 1 MANUAL HEIGHT om 1138 Eat K2C Series Installation Instructions K2C22HSXF1 5 675 171 5 28 72 5 Ll 50s De H A 3 46 5 88 0 Hi ata 1 12 32 5 57 e Ki 1415 VINE PATTERN TILT RANGE MANUAL HEIGHT Het Installation Instructions K2C Series LEGEND Tighten Fastener Apretar elemento de fijaci n Befestig
6. INSTALLATION INSTRUCTIONS K2C22H K2C22HSXF1 K2C Column Mounts G CHIEF K2C Series Our Mounts Your Vision K2C Series Installation Instructions DISCLAIMER Milestone AV Technologies and its affiliated corporations and subsidiaries collectively Milestone intend to make this manual accurate and complete However Milestone makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind Milestone makes no representation of warranty expressed or implied regarding the information contained herein Milestone assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document Chief is a registered trademark of Milestone AV Technologies All rights reserved A IMPORTANT SAFETY INSTRUCTIONS WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions WARNING Failure to read thoroughly understand and follow all instructions can result in serious personal injury damage to equipment or voiding of factory warranty It i
7. desk mounting See Figure 1 NOTE If space is limited behind desk i e against wall etc remove lower piece of clamp and two screws holding it to the mount and reattach parts prior to Step 3 See Figure 2 2 Place mount on top of desk at desired mounting location See Figure 1 3 Tighten clamp using clamp screw until mount is securely fastened to desk See Figure 1 Figure 1 Figure 2 Grommet Hole Option NOTE K1C clamp mounts may be installed directly to grommet holes between 1 1 4 and 2 1 2 in diameter If grommet hardware F H is used they can be installed to grommet holes between 3 8 and 2 1 2 in diameter Direct Installation 1 Remove lower piece of clamp from assembly by removing two button head cap screws holding piece to assembly See Figure 3 2 Install remaining part of clamp through grommet hole See Figure 3 Figure 3 3 Reattach removed piece of clamp and screws to assembly See Figure 4 4 Tighten clamp using clamp screw until mount is securely fastened to desk See Figure 4 ov x2 ly Figure 4 K2C Series Installation Instructions Using Grommet Hardware 1 Remove desk clamp from mount by loosening button head cap screw until clamp is completely disengaged from the bolt See Figure 5 Maneuver clamp so t
8. hat it is totally removed from desk mount See Figure 5 NOTE Set removed washer aside for re use Figure 5 Locate a flat surface thickness of 3 4 minimum to 3 1 2 maximum on which to mount the column plate If mounting hole does not already exist on desk drill 3 8 mounting hole in desk at desired mounting location IMPORTANT Mounting hole must be between 3 8 and 2 1 2 in diameter 5 6 Place mount on desk over grommet hole See Figure 6 Use 5 16 18 x 6 button head cap screw H clamp bracket F and 5 16 18 square nut G to secure mount to desk See Figure 6 10 Figure 6 Assembly to Office Furniture Rail SFX1 Models IMPORTANT The SFX1 models are designed to be installed to Steelcase Frame One office furniture rails Do NOT attempt to install these mounts to any other type of office furniture rails NOTE If mounting holes on displays are recessed it may be necessary to install displays prior to installing assembly Proceed to Display Installation Section prior to installing assembly to rail 1 Drop channel plate K at an angle into front groove of Frame One rail See Figure 7 2 Make sure channel plate L lays flat in rail and slide plate until it is at desired mounting position See Figure 7 side view Frame One rail at final position Figure
9. ing See ADJUSTMENT for detail Carefully place display face down on protective surface Place the four spacers D over each of the mount holes on the back of the display See Figure 12 4 Pickup and orient the mount A so that mounting holes are aligned with the holes in the spacers rotate the bracket as required See Figure 12 5 Using Phillips screwdriver install four M4x25mm screws C through the mounting holes through the spacers and into the display See Figure 12 6 Tighten all four screws Do not overtighten Figure 12 K2C22H Models 1 Remove quick release faceplate from mount by pulling quick release lever and sliding faceplate off mount See Figure 13 Figure 13 2 Carefully place display face down on protective surface Connect faceplate to display For flush mounting hole installation e Using Phillips screwdriver carefully install four M4x14mm screws B through corresponding holes on faceplate and into the mounting holes on the display See Figure 14 for flush mounting holes Tk quick release faceplate ovo Figure 14 13 K2C Series Installation Instructions For recessed mounting hole installation Place four spacers D on top of mounting holes on back of display See Figure 15 Using Phillips screwdriver carefully install four M4x25mm screws C th
10. n Mei Street Fotan Shatin Hong Kong 852 2145 4099 852 2145 4477
11. olumn adjustment knob See Figure 20 Figure 20 Adjustments K2C22H models only 1 2 Loosen knobs securing faceplates to array See Figure 21 Slide displays laterally on array to adjust lateral shift See Figure 21 Adjust pitch and pivot position as desired See Figure 21 Tighten knobs to secure faceplates in position See Figure 21 Figure 21 Array Bar Roll Adjustment 1 2 3 Loosen roll adjustment screws on back of array bracket See Figure 22 Adjust roll of array bar as desired See Figure 22 Tighten roll adjustment screws on back of array bracket See Figure 22 Figure 22 15 K2C Series Installation Instructions Pivot Adjustment Range Single Arm Models 1 Adjust arm angle as desired up to 90 degrees in either direction See Figure 23 WARNING Swinging the arm beyond 90 degrees may result in the mount slipping off the desk causing serious injury edge of desk or wall face top view 90 degrees range of motion Figure 23 Dual Arm Models 1 Adjustarmangles as desired within a 90 degree range from the edge of desk or wall and a perpendicular centerline of mount See Figure 24 WARNING Swinging the arm beyond this range may result in the mount slipping of the desk causing
12. rough corresponding holes on faceplate spacers D and into the mounting holes on the display See Figure 15 for recessed mounting holes quick release faceplate Figure 15 4 Position display with faceplate attached above mount See Figure 16 5 Slide faceplate onto mounting head until quick release tab clicks into place See Figure 16 Figure 16 14 Handle Installation K2C22 models only 1 Loosen four screws securing handle brackets to K1C22H array See Figure 17 2 Install uprights of handle J into handle brackets located on the back of K1C22 array See Figure 17 Figure 17 3 Position handle J at desired height and secure by tightening button head cap screws attaching handle brackets to array See Figure 18 Figure 18 Installation Instructions K2C Series Adjustments Portrait Adjustment K2C22H Models only 1 The monitor may be adjusted 90 degrees in either direction in order to provide a portrait view of the monitor See Figure 19 Use 3 16 hex key P to adjust rotational adjustment screw to adjust rotational tension See Figure 19 portrait tension Figure 19 Column Height Adjustment 1 2 3 Loosen column adjustment knob See Figure 20 Adjust height to desired level See Figure 20 Tighten c
13. s the installer s responsibility to make sure all components are properly assembled and installed using the instructions provided WARNING Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment Reinforce the structure as required before installing the component WARNING Use this mounting system only for its intended use as described in these instructions Do not use attachments not recommended by the manufacturer WARNING Never operate this mounting system if it is damaged Return the mounting system to a service center for examination and repair WARNING Do not use this product outdoors WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of all components located between the K2C Series Monitor Arm up to and including the display does not exceed the weight limits listed below Use with products heavier than the maximum weight indicated may result in collapse of the mount and its accessories causing possible injury K2C110 22 lbs 22 Ibs 9 98 kg 9 98 kg K2C120 22 lbs 22 Ibs 9 98 kg 9 98 kg K2C220 22 lbs 44 lbs 9 98 kg 19 96 kg VIP aM 22 Ibs 22 Ibs 9 98 kg 9
14. serious injury top view edge of desk or wall face amp LT n 90 degrees range Gen i perpendicular centerline Figure 24 16 Swing Arm Pivot Adjustment 1 Adjust pivot position as desired See Figure 25 2 Adjust pivot point tension screws to change pivot adjustment tension See Figure 25 pivot point tension Figure 25 Cable Management Non Array Models 1 Route cables through cable management channels See Figure 26 Figure 26 K2C Series Installation Instructions Array Models 1 Install cable clips J7 to back of array See Figure 27 Route cables through cable clips J7 as desired See Figure 27 2 Figure 27 17 K2C Series Installation Instructions 18 Installation Instructions K2C Series 19 K2C Series Installation Instructions USA International G CHIEF Our Mounts Your Vision Europe Chief a products division of Milestone AV Technologies Asia Pacific 8800 002481 Rev00 2014 Milestone AV Technologies www chiefmfg com 03 14 gt TU 6436 City West Parkway Eden Prairie MN 55344 800 582 6480 952 225 6000 877 894 6918 952 894 6918 Franklinstraat 14 6003 DK Weert Netherlands 31 0 495 580 852 31 0 495 580 845 Office No 918 on 9 F Shatin Galleria 18 24 Sha
15. ungsteil festziehen Apertar fixador Serrare il fissaggio Bevestiging vastdraaien Serrez les fixations Pencil Mark Marcar con lapiz Stiftmarkierung Marcar com lapis Segno a matita Potloodmerkteken Marquage au crayon Loosen Fastener Aflojar elemento de fijaci n Befestigungsteil l sen Desapertar fixador Allentare il fissaggio Bevestiging losdraaien Desserrez les fixations Drill Hole Perforar Bohrloch Fazer furo Praticare un foro Gat boren Percez un trou Phillips Screwdriver Destornillador Phillips Kreuzschlitzschraubendreher Chave de fendas Phillips Cacciavite a stella Kruiskopschroevendraaier Tournevis pointe cruciforme Adjust Ajustar Einstellen Ajustar Regolare Afstellen Ajuster Open Ended Wrench Llave de boca Gabelschl ssel Chave de bocas Chiave a punte aperte Steeksleutel Cl fourche Remove Quitar Entfernen Remover Rimuovere Verwijderen Retirez By Hand A mano Von Hand Com a m o A mano Met de hand la main Optional Opcional Optional Opcional Opzionale Optie En option C d y E d 3 Hex Head Wrench Llave de cabeza hexagonal Sechskantschl ssel Chave de cabeca sexta
16. vada Chiave esagonale Zeskantsleutel Cl t te hexagonale 09 3 Security Wrench Llave de seguridad Sicherheitsschl ssel Chave de seguranca Chiave di sicurezza Veiligheidssleutel Cl de s curit K2C Series Installation Instructions TOOLS REQUIRED FOR INSTALLATION ei 3 16 included 1 8 Een e 242 0 7 Desk clamp armj K2C110 shown A Frame One arm K2C120SXF1 shown 6 included with SXF1 models only K 1 Z Channel plate B 4 or 8 C 4 or 8 D 4 or 8 Lui MAS M10x5 3x10 L 2 Grommet Hardware included with clamp Shim models only P d F H 1 ii ee Clamp bracket G 1 5 16 18 x 6 10732 x718 5 16 18 eudec with K1C22 Models 4 1 J5 1 Pocket washer 5 16 18 Array J6 1 J7 2 clip A J3 1 5 16 18 x 3 C 0 J4 1 Handle Pivot pin J8 2 J9 1 J10 1 J11 1 J12 1 Cable Thin steel Plastic Rotational Cable clip Pivot point washer washer spacer spacer N 1 3 16 P 1 1 8 Installation Instructions K2C Series Assembly And Installation Connecting Desk Clamp Arms to Desk K2C110 K2C120 K2C220 K2C22H 1 Loosen clamp screw until enough space is created between clamp and mount to allow for

Download Pdf Manuals

image

Related Search

Related Contents

Système de filtration d`eau pour meuleuse d`opticien Mode d`emploi  安全上のご注意  shogun  Tutti i messaggi relativi alla sicurezza specificano il potenziale  PART ONE LCCR    mode d`emploi  15648 ES-PT Aldi N Cover RC3.indd  Philips TDA7057AQ User's Manual  マニュアル 日本語(PDF:1.60MB)  

Copyright © All rights reserved.
Failed to retrieve file