Da-Lite 70272 projection screen
Contents
1. Blue Manual 2 Brown 12V Blue Yellow Bus RP Data Yellow Green RQ Data Green Red 5V Red Ground Black Black RO Clock Orange White Manual 1 Purple Standard RJ 22 can be used in place of RJ 14 cable Installation for 220 240V Screens ILT RJ 9 Pin Outs Tab Is Facing Up 240V Wiring Diagram IMPORTANT NOTE The wall switch is REQUIRED to make Bau F hel s or Up lack any limit switch adjustments EVEN if a third party control ac on l i Ground C Red system is used Therefore it is advised to wire the switch P A i G or provide a 4 conductor connection that is accessible Y S lt Data or Down White Blue Common Ba ba Power Input Brown Hot R UP UPDN GND 240VAC 50Hz 45V Green STOP Green 3 POSITION Ground to Case E DOWN SWITCH RUO s S gt A Bulan Ea H O Ground oor Splitter Front of Wall Back of Dry Contacts Switch Wall Switch Troubleshooting Visit www da lite com products product_videos php to find installation and troubleshooting videos and tutorials You will also find a link to Live Chat for interactive support and you can Symptom Cause contact us by email at info da lite com or by phone at 800 622 3737 or 574 267 8101 with any troubleshooting Solution Screen will2. INSTRUCTION BOOK FOR Tensioned Large Cosmopolitan Electrol DA LITE Important Safety Instructions When using your video equipment basic safety precautions should always be followed including the following J Read and understand all instructions before using 2 Position the cord so that it will not be tripped over pulled or contact hot surfaces 3 If an extension cord is necessary a cord with a current rating at least equal to that of the appliance should be used Cords rated for less amperage than the appliance may overheat 4 To reduce the risk of electric shock do not disassemble this appliance Contact an authorized service dealer when repair work is required Incorrect reassembly can cause electric shock when the appliance is used subsequently 5 The use of an accessory attachment not recommended by the manufacturer may cause a risk of fire electric shock or injury to persons Installation Carefully unpack screen and remove outer wrapping from case The slat retainer screws must be removed before installation Use supplied 1 8 nex key to remove silver shipping brackets attached to slat and screen case Orient the case with the slat down and then remove the screws The case must remain in that orientation throughout the installation process to avoid fabric damage The Tensioned Large Cosmopolitan Electrol comes with brackets to allow for wall mount or ceiling mount installat
3. Lite branded products to the original purchaser only to be free from defects in materials and workmanship for a period of one 1 year from the date of purchase by the original purchaser provided they are properly operated according to Da Lite s instructions and are not damaged due to improper handling or treatment after shipment from the factory This warranty does not apply to equipment showing evidence of misuse abuse or accidental damage or which has been tampered with or repaired by a person other than authorized Da Lite personnel Da Lite s sole obligation under this warranty shall be to repair or to replace at Da Lite s option the defective part of the merchandise Returns for service should be made to your Da Lite dealer If it is necessary for the dealer to return the screen or part to Da Lite transportation expenses to and from Da Lite are payable by the purchaser and Da Lite is not responsible for damage in shipment To protect yourself against damage or loss in transit insure the product and prepay all transportation expenses TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING WARRANTIES AS TO FITNESS FOR USE AND MERCHANTABILITY Any implied warranties of fitness for use or merchantability that may be mandated by statute or rule of law are limited to the one 1 year warranty period This warranty gives you specific legal rights and you may al
4. ed with LVC 240 VOLT WIRING DIAGRAM FOR STANDARD WALL SWITCH Da Lite offers two styles of 240 volt wall switches for standard operation Please see wiring diagram in wall switch boxes included with screen Installation For 120V Screens 120V Wiring Diagram 3 conductor 20 24 gauge wire can be used in place of the supplied RJ 14 cable to connect the wall switch Connect the BUS terminals on the wall switch to the corresponding BUS terminals on the splitter board Up Limit Tactile Button Down Limit Tactile Button Front of Wall Switch RJ 22 Jack Connection to Wall Switch Wire IMPORTANT NOTE The wall switch is REQUIRED to make any limit switch adjustments EVEN if a third party control system is used Therefore it is advised to wire the switch or provide a 3 conductor connection that is accessible Up Dry Contact Down Dry Contact Common Both Bus Bus 5V Bus Receptacle RJ 45 Jack Data ae Cable White Green Ground Common Black Ground Must be Connected Hot to Building Ground RJ 14 Pin Outs Tab Is Facing Up Power Input 120VAC 60Hz RJ 22 Pin Outs Tab Is Facing Up RJ 45 Pin Outs Tab Is Facing Up 12V Bus RP Data L White Bus RP Data RQ Data Green RQ Data 5V C Rea 5V Ground Black Ground RQ Clock Supplied RJ 14 cable
5. ions Procedures for each method are as follows Wall Mount 1 The wall mount bracket should be fastened to wall studs or some reinforcement within the wall Concrete or brick walls f require special fasteners and anchors y 2 The wall bracket has holes spaced at 16 and 24 to align with most wall studs Case Hook 3 The bracket must be level and plumb Wall Mount 4 Keep in mind you will need at least 2 3 4 between the ceiling Bracket and the top of the wall mount bracket to be able to position the case on the bracket 5 Mount the screen case on the wall bracket as shown in i Stop Screw lt figure 1 Be sure the case is fully seated on the bracket Viewing Surface Tighten the stop screws against the wall bracket Audience Side Y Ceiling Mount Figure 1 1 Be sure the ceiling has adequate reinforcement to attach the P screen brackets Case Hook 2 Attach the ceiling brackets to the wall mount bracket using Ceiling Mount the supplied 5 16 x 3 4 bolts washers and nuts Bracket 3 Position the ceiling bracket assembly on the ceiling and Moe n attach with 5 16 bolts not supplied The bolts should be Washer long enough to pass through the drywall or ceiling tile and 5 penetrate at least 1 1 2 into the reinforcement in the ceiling Wall Mo
6. not operate Motor does not hum Blown fuse Tripped circuit breaker No power to operating switch or junction Power at junction box Thermal overload tripped Broken wire in the down or up position Defective motor limit switch or capacitor Capacitor burned out Replace fuse Reset circuit breaker Check above Tighten all loose wire connections Correct any improper connections Do wn Position Check for power across black and white leads Up Position Check for power across red and white leads Le motor cool down for 15 minutes Try again Check for continuity Cut off old splice and reconnect Replace motor assembly NOTE Motor is a sealed assembly Replace motor assembly Incorrect stopping position in downward direction Lost roller wrap Down limit switch out of adjustment See instructions below Co ntact Da Lite at 800 622 3737 or 574 267 8101 Incorrect stopping position in upward direction Lost roller wrap Up limit switch out of adjustment See instructions below Co ntact Da Lite at 800 622 3737 or 574 267 8101 Noise NOTE Screen will operate with a low pitched hum Gear noise Re place motor assembly Coasting Defective brake Re place motor assembly LIMITED ONE YEAR WARRANTY ON DA LITE PRESENTATION PRODUCTS Milestone AV Technologies LLC warrants certain Da
7. so have other rights which vary from state to state TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW NO LIABILITY IS ASSUMED FOR EXPENSES OR DAMAGES RESULTING FROM INTERRUPTION IN OPERATION OF EQUIPMENT OR FOR INCIDENTAL DIRECT OR CONSEQUENTIAL DAMAGES OF ANY NATURE In the event that there is a defect in materials or workmanship of a Da Lite product you may contact our Sales Partners at PO Box 137 Warsaw IN 46581 0137 574 267 8101 800 622 3737 IMPORTANT THIS WARRANTY SHALL NOT BE VALID AND DA LITE BRANDED PRODUCTS SHALL NOT BE BOUND BY THIS WARRANTY IF THE PRODUCT IS NOT OPERATED IN ACCORDANCE WITH THE DA LITE WRITTEN INSTRUCTIONS Keep your sales receipt to prove the date of purchase and your original ownership A Milestone AV Technologies Brand 3100 North Detroit Street Warsaw Indiana 46582 P 574 267 8101 or 800 622 3737 F 574 267 7804 or 877 325 4832 E info da lite ccom www da lite com DL 0179 Rev 1 07 14 2014 Milestone AV Technologies LLC Printed in U S A 98770
8. unt 1 4 Mount the screen on the wall bracket as shown in figure 2 Be Bracket sure the case is fully seated on the bracket Tighten the stop screws against the wall bracket Stop Screw lt Viewing Surface Audience Side Y Figure 2 Screen Adjustment Screen travel is stopped automatically in the down and up positions by the limit switches that are preset at the factory No further adjustment is necessary CAUTION Contact Da Lite at 800 622 3737 or 574 267 8101 if screen motor needs adjustment ASATTENTION Contactez Da Lite au 800 622 3737 ou au 574 267 8101 au cas le moteur de l cran a besoin d tre ajust Tensioned Large Cosmopolitan Electrol Installation For Screens Without A Built In Low Voltage Control Internal wiring has been completed at the factory Installer must route power to the wall switch and to the junction box located on the left end of the screen case See wiring diagram below for wire connections NOTE This screen can only be controlled by a single 120VAC or 240VAC wall switch To use multiple switches an optional low voltage control must be used 120V Wiring Diagram For Standard Wall Switch Junction Box Located In Left Endcap NOTE A single switch cannot be used to operate more than one screen Contact the factory for further information AC Common SPDT Switch with Center Off Up Off AC Hot 120VAC 60HZ 1 AMP Black Yellow Down This Switch Can Not be us
Download Pdf Manuals
Related Search