Lenco BTT-100 loudspeaker
Contents
1. successfully FM radio operation TUNING THE FM RADIO 1 Press the POWER ON OFF button on the unit then press the STANDBY button to power on the unit 2 Switch to the radio mode by pressing the MODE button on the unit or FUNTION button on the remote repeatedly 3 Press the TUNING button to fine tune radio station Press and hold the TUNING button to auto search radio station forward or backward respectively When an available station is found the unit will broadcast it immediately and the searching will stop 4 During radio playback press the PLAY PAUSE button on the remote to switch FM STEREO on or off 5 During FM radio mode and program service name being displayed it is able to recall the frequency and PTY of the current station by pressing and holding VOLUME INFO button on remote control It will show the station frequency for 3 seconds subsequently display PTY in next 3 seconds and then get back to original program service name display STORING YOUR FAVORITE RADIO STATION 1 Tune to your favorite station first press and hold the MEMORY button on the remote for storing the current station memory cell number flashes on the screen 2 Use the CH or CH button on the remote to select the corresponding memory cell among CH 01 CH 20 for storing the station 3 Confirm your selection by pressing the MEMORY button on the remote 4 During radio playback press the MEMORY button and then press the or CH button on t2. IOUS button to skip forward or backward 7 Press the POWER ON OFF button on the unit then press the STANDBY button to power on the unit 2 Press the FUNTION button on the remote or the MODE button on the unit repeatedly to switch to the Bluetooth mode PAIRING shows on the screen LED indicator blinks rapidly while it is pairing Pair and connect to Lenco BTT 100 on the Bluetooth audio source device If prompted for passcode enter 0000 Pairing successful LED indicator turns to solid blue ready to stream music Note Pairing mode is canceled in about 1 5 minutes The above are generic steps to pair a Bluetooth device for more specific instructions on Bluetooth connectivity for your device please consult your manufacturer s manual After the first connection the unit will detect your last paired Bluetooth device and connect to it automatically RE CONNECT TO THE BLUETOOTH AUDIO SOURCE DEVICE UNDER BLUETOOTH MODE If the device is already paired with the Lenco BTT 100 but became unconnected even with both Bluetooth devices turned on You can re connect them by following steps 1 Press the BT button on the unit or press and hold BT button on the remote to re link the audio source device The Bluetooth indicator will blink for connecting 2 Select Lenco BTT 100 on the audio source device for connecting Bluetooth indicator will turn to solid blue if the Lenco BTT 100 and the device have been re connected
3. Lenco Important safety instructions e The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids such as vases shall be placed on the apparatus When the mains plug or an appliance coupler is used as the disconnect device the disconnect device shall remain readily operable To be completely disconnected the power input the mains plug of the apparatus or the appliance coupler shall be disconnected from the mains completely e No naked flame sources such as lighted candles should be placed on the apparatus Minimum distances 2 0cm around the apparatus for sufficient ventilation The ventilation should not be impeded by covering the ventilation openings with items such as newspapers table cloths curtains etc e The use of apparatus is in moderate climates e Attention should be drawn to the environmental aspects of battery disposal CAUTION Danger of explosion if battery is incorrectly replaced Replace only with the same or equivalent type e Battery shall not be exposed to excessive heat such as sunshine fire or the like Features amp technical data Power source AC 110 240V 50Hz 60Hz Power consumption 100W Battery of remote control CR2025 x 1 Tuning range FM 87 5 108 MHz Output Power RMS At 10 THD Around 25W x 2 Subwoofer 50W x 1 Bluetooth compatible v 2 1 EDR A2DP AVRCP Compatible with USB SD card Dimensions 325 L x 320 W x 1261 H mm Operating Humid
4. ations and external appearance of the set are subject to change without prior notice This symbol indicates that the relevant electrical product or battery should not be disposed of as general household waste in Europe To ensure the correct waste treatment of the product and battery please dispose them in accordance to any applicable local laws of requirement for disposal of electrical equipment or batteries In so doing you will help to conserve natural resources and improve standards of environmental protection in treatment and disposal of electrical waste Waste Electrical a and Electronic Equipment Directive Declaration of Conformity Products with the CE marking comply with the EMC Directive 2004 108 EC and the Low Voltage Directive 2006 95 EC issued by the Commission of the European Community Hereby STL Group BV Ankerkade 20 NL 5928 PL Venlo declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 1999 5 EC The declaration of conformity may be consulted at https lencosupport zendesk com forums 22413161 CE Documents This product operates at 2400 2483 5 MHz and is designated only to be used inside a normal household environment This product is suited for this purpose within all EU counties C 0700 GAII rights reserved For information and support www lenco com
5. button to adjust the treble After adjusting the bass or treble effect the unit will resume the previous display automatically Connection with other device AUX IN O C m Co CI 1 Connect the AUX in jacks on the unit to an audio source for example DVD player with an RCA cable 2 Power on the unit following the corresponding instructions 3 Press the MODE button on the unit or the FUNCTION button on the remote repeatedly to switch to AUX mode 4 Use the native controls on the connected audio device to begin playing music through the connected unit Troubleshooting Symptom Possible Cause Solution Radio sound distorted 1 The station is not tuned in 1 Fully unwind the FM wire 2 There is a poor signal in the antenna and fine tune the area station 2 Fully unwind the FM wire antenna and reposition the unit No radio sound 1 The unit is not in tuner mode 1 Switch to radio mode following 2 The volume has been muted the corresponding instructions or is on the minimum setting 2 Adjust the volume level or press the MUTE button to resume audio Sound distorted while 1 The original audio file is 1 Skip to other track as attempt playing card or USB distorted No sound at Bluetooth 1 The Bluetooth device is not 1 Follow the instructions to pair the mode paired with the unit Bluetooth device to the unit 2 The volume has been muted 2 Adjust the volume level or press
6. he remote repeatedly to recall the stored stations USB amp SD card operation 1 Power on the unit by following the corresponding instructions Insert a SD card or a USB onto the unit and press the FUNCTION button on the remote or MODE button on the unit repeatedly until toggle the unit to CARD or USB mode After the unit scans the inserted card or USB playback will start automatically Press the RANDOM button on the remote to enable or disable the random playback Press the PLAY PAUSE button to pause playback press this button again to resume normal play During playback use the NEXT PREVIOUS button to skip forward or backward Press and hold the FAST FORWARD BACKWARD button to search through the current track forward or backward 7 Press the STOP button on the unit or press and hold the STOP button on the remote to cease the playback m Sound operation MUTE THE UNIT During playback press the STANDBY MUTE button on the remote to mute the audio Press this button 4 again to resume the audio During playback press and hold STANDBY MUTE button on the remote to enter standby mode VOLUME LEVEL ADJUSTMENT Press the VOLUME button to adjust the volume output level TONE SETTING FOR THE UNIT During playback press the TONE button on the remote once and use the VOLUME button to adjust the bass During playback press the TONE button on the remote twice repeatedly and use the VOLUME
7. ity Range 10 96 to 75 96 Operating temperature range 5 C to 35 C Specifications are subject to change without notice Description of parts 14 16 18 2 MAIN UNIT 1 ook 11 12 13 14 15 16 17 18 TUNING amp PREVIOUS FAST BACKWARD BUTTON VOLUME BUTTON VOLUME BUTTON PLAY PAUSE BUTTON STANDBY BUTTON TUNING amp NEXT FAST FORWARD BUTTON BT PAIR BUTTON MODE BUTTON STOP BUTTON 10 BLUETOOTH INDICATOR REMOTE SENSOR LCD DISPLAY AC SOCKET POWER ON OFF BUTTON SD CARD SLOT USB PORT AUX IN JACKS FM ANTENNA REMOTE CONTROL 1 TONE CH BUTTON 2 VOLUME STOP BUTTON 3 TUNING amp PREVIOUS FAST BACKWARD BUTTON BT PAIR amp PLAY PAUSE BUTTON STANDBY MUTE BUTTON FUNCTION CH BUTTON VOLUME INFO BUTTON TUNING amp NEXT FAST FORWARD BUTTON 9 MEMORY RANDOM BUTTON Installation AC POWER CONNECTION 1 2 Plug one end of the AC cord into the AC socket on the unit Then connect the other end to the main power NOTE During playback if not any operation in about 6 hours the unit will switch to standby mode automatically Bluetooth operation BLUETOOTH CONNECTION This unit can receive stereo audio signal from a Bluetooth stereo audio source device 1 3 4 5 6 Press PLAY PAUSE button to pause or start the playback During playback press the NEXT PREV
8. or is on the minimum setting the MUTE button to resume audio Service amp support For information www lenco com For support http lencosupport zendesk com Lenco helpdesk Germany 0900 1520530 Local charges The Netherlands 0900 23553626 Local charges 1ct p min Belgium 02 6200115 Local charges France 03 81484280 Local charges The helpdesk is accessible from Monday till Friday from 9 AM till 6 PM When contacting Lenco you will always be asked for the model and serial number of your product The serial number can be found on the back of the device Please write down the serial number below Model BTT 100 Serial number Lenco offers service and warranty in accordance to European law which means that in case of repairs both during and after the warranty period you should contact your local dealer Important note It is not possible to send products that need repairs to Lenco directly Important note If this unit is opened or accessed by a non official service center in any way the warranty expires This device is not suitable for professional use In case of professional use all warranty obligations of the manufacturer will be voided Notice statement and information Manufacturer of this unit follows a principle of continuous improvement and has no responsibility for any changes that are made to the unit nor any liability for these changes Lenco is not liable for printing errors in the manual The specific
Download Pdf Manuals
Related Search