Home

Soundstream PN4.520D

image

Contents

1. WWW SOUNDSTREAM COM asia NANO Introduction SOUND STREAM is dedicated to the pursuit of audio fidelity Our prime objectives are to design and manufacture audio products of unsurpassed quality to provide unparalleled support and service for these products and to conduct business in a manner that will enhance the quality of life for all involved SOUND STREAM uses both types of power supplies depending on the intended use of each amplifier as well as expected current demands and operating environment Features 4 Channel RZ4 1200D RZ4 2000D e Class D Digital Full Range Amplifier e Full MOSFET PWM Power Supply e SMD Technology on Double Sided PCB e 8ga Power Terminals amp 12ga Speaker Outputs High amp Low Level Signal Inputs e Selectable 80Hz 12dB High Low Pass Filter 2 Ohm Stereo 4 Ohm Bridged Stable e Total Harmonic Distortion 0 5 Frequency Response 10 35kHz Signal to Noise Ratio 70dB e Damping Factor gt 250 e Stereo Channel Separation lt 55dB e Input Sensitivity 200mV 6V Mono Block RZ1 1500D RZ1 2300D e Class D Digital Monoblock Amplifier e Full MOSFET PWM Power Supply e SMD Technology on Double Sided PCB e 8ga Power amp 8ga Speaker Output Terminals e High amp Low Level Signal Inputs e Remote Mount Gain Control Included e Variable 35 250Hz 12dB Low Pass Filter e Variable 10 50Hz 12dB Subsonic Filter e Variable 0 12dB 45Hz Bass Boost e Total Harmonic Distortion 0 5 e Fre
2. Ww Ww a a y i 2 IF le D y ww fos a a U WL U UE lt lt o Q o o a 2 2 5S D ES RL White Black RL White BR RR Gray Black RR Gray BR 6 FL Green Black O FL Green BR FR Violet Black FR Violet BR MODEL NO PN4 320D PN4 520D Stereo Separation Speaker out connection The ability of an amplifier to maintain the separation between the right and left channels is what allows an amplifier to reproduce an accurate sound stage Music is recorded with each instrument in its own location on a sound stage You should hear it the same way in your vehicle 20 80 Gray Black 20 80 STEREO MODE oz a en mi acu WA e a g a Est R En E ag Rear CH Front CH ail LEGH L El 3 E L BRIDGED MODE MODEL NO PN4 320D PN4 520D Speaker out connection SPEAKER OUT FUSE POWER eee 12V DC REM GND MODEL NO PN1 450D SUB WOOFER PN1 650D Installation Guidelines Mounting
3. 8 0V 1 0V 8 0V 1 0V 8 0V Low pass Filter High pass 80Hz Fixed 12dB Oct 80Hz Fixed 12dB Oct 50 250Hz 12dB Oct Low pass only 50 250Hz 12dB Oct Low pass only Frequency Sub sonic filter 10Hz 50Hz 10Hz 50Hz Bass boost 0 12dB 45Hz 0 12dB 45Hz Chanel separation S N Ratio THD lt 0 05 lt 0 05 lt 0 05 lt 0 05 Power supply 11 16V DC 11 16V DC 11 16V DC 11 16V DC Dimension in 4 75 x1 5 x7 4 75 x1 5 x9 4 75 x1 5 x8 4 75 x1 5 x9 Weight Kg 1 4 1 8 1 6 Output power TR design Digital Full range Digital Full range Class D Mono Turning on the amplifier The amplifier automatically turns on a few seconds after you turn your vehicle s ignition switch to ACC or ON or turn on your auto sound system depending on how you wired the system The POWER Indicator on the top of the amplfier lights when the amplifier is on Important Your amplifier requires 30 amps or more of power from your vehicle s battery during operation To protect your battery from discharging do not operate the amplifier unless your vehicle is running Adjusting the audio level For the best performance you must set GAIN MIN MAX on the side of the amplifier to adjust the level of the audio signals that enter the amplifier 1 Use a screwdriver to turn GAIN MIN MAX fully counterclockwise to MIN 2 Turn the auto
4. YES amplifier overheating AMP NOT No power to remote heck J SWITCHING wire with receiver on Check connections to radio ON Burnt or broken fuse Replace fuse Check Speaker cad Inspect for short circuit or an NO SOUND re open connection ON ONE Reverse Left and Right RCA inputs CHANNEL 2 p Check Audio Leads to determine if the problem is occurring before the amp Check Speaker load Be sure proper speaker load AMP impedance impedance recommendations TURNING are observed EDHUM If you use an ohmmeter to check HIGH speaker resistance please VOLUME remember that DC resistance and AC impedance may not be the same h Turn radio down shutdown Wait for AMP to cool PROTECTION A Er ei eparate speake es ani en en Warning Investigate the layout of your automobile through before drilling or cutting any holes Take care when you work near the gas tanks lines or hydraulic lines and electrical wiring Don t use power amplifier without securely mounting it Attach this system securely to the automobile to prevent damage particularly in the event of an accident Don t mount this system so that the wire connections are unprotected or are subject to pinching or damage from nearby objects The 12V DC power wire must be fused at the battery positive terminal connection Before making or breaking power connections at this system power terminals disconnect the 12V wire at the battery end Confirm your radio cassette player
5. your Reference Amplifier is easy Keep in mind the following guidelines e Negative battery terminal must be disconnected before any electrical connections are made e The amplifier may be mounted in any direction on wood metal or carpet e The metal case of the amplifier may be grounded or left isolated e The amplifier requires adequate ventilation Position the amplifier with sufficient surrounding area for proper cooling e Keep the amplifier out of the engine compartment and other locations that may cause excessive heat or moisture e Make sure that the mounting screws will not penetrate the gas tank brake and fuel lines wiring or other critical parts of your car when installed Do not mount the amplifier to a subwoofer enclosure or any other place that may have excessive vibration T i z LH ao 2 xi A Q V A T A 0 EE A a madi L___ N Specifications Specification 4 Ohm RMS PN4 320D 60W x 4ch PN4 520D 100W x 4ch PN1 450D 260Wxch PN1 650D 400Wx1ch Out power 2 Ohm RMS 80Wx4ch 130W x 4ch 450Wx1ch 650Wx1ch Bridged 160Wx2ch 260Wx2ch x x Frequency range 20Hz 30Khz 4ohm 20Hz 30Khz 4ohm 20Hz 30Khz 20Hz 30Khz Speaker impedance 2 4 8 Ohm Oo O O Input Line Low 0 20V 6 0V 0 20V 6 0V 0 20V 6 0V 0 20V 6 0V sensitivity finia igh inpu 1 0V 8 0V 1 0V
6. PN4 520D PN1 650D Power connections It is important to have good quality power and ground connections Remember to complete an electrical circuit the ground connection is just as important as the positive power connection Before any power connections are made disconnect the ground cable at the battery When the power supply lead memory backup lead or ground lead are extended use a 5mm AWG5 or larger automotive grade cable which will withstand friction and heat to safe grade against fires occurring as a result of short circuiting GND Connect the proper gauge ground wire to the amplifier GND terminal Locate the position on the chassis of the car to which the amplifier is to be grounded NOTE Do not ground the amplifier to the frame of the car The frame on most cars and trucks is not grounded to the chassis body Use Solder or a clamp ring to connect the ground wire Pre drill the prepped chassis to bolt the ground ring terminal with nut bolt and lock washers Insulate metal and connector with paint or silicon to prevent rust and oxidation Silicon also works great to prevent nuts and bolts from working loose in a harsh environment of an automobile Upon completion of the ground connection grab wire or connector and confirm that it is a solid connection To prevent engine noise it is recommended to ground the head unit and other audio electronics in the same location REM Connect the remote wire power anten
7. and or other equip is turned off while connecting the input jacks and speaker terminals lf you need to replace the power fuse replace it only with a fuse identical to that supplied with the system Using a fuse of different type or rating may result in damage to this system which isn t covered by the warranty 11 SOUNDSTREAM C H N O Please Keep This Information For Your Records Product Model Serial Number Date Purchased Name of Dealer Dealer Address City State Zip STAMP SoundStream Technologies 1550 S Maple Ave Montebello CA 90640 Attn Customer Service S UNDSTREAM C H N O SoundStream Technologies warrants this product to be free from defects in materials and workmanship under normal use and conditions for a period of 1 year from the original date of purchase if purchased and professionally installed by an Authorized SoundStream dealer Any product purchased from and or installed by others will be warranted for 90 days only This warranty does not cover any expenses incurred in the removal or re installation of the product and is offered to the original purchaser only Should service be necessary for any reason due to a manufacturing defect or malfunction during the warranty period SoundStream Technologies will repair or replace at its discretion the defective merchandise at no charge upon delivery of the product to the address shown below with proof of purchase Befor
8. c Caution Continuous exposure to excessive sound pressure levels may cause permanent hearing loss SOUND STREAM strongly advises that you use common sense when setting volume levels Ifyou experience ringing in the ears it could cause permanent hearing damage CAUTION When connecting our amplifiers to pre wired stock speakers care must be taken that there are no common connections between left and right speaker wires i e minus to minus or plus to plus connections as this will cause the amplifier to go into immediate protection or may cause damage to the amplifier Output connections are not common chassis ground Please follow the hookup instructions in this owner s manual Wire Size Most people understand the importance of a clean signal source for good sound reproduction Its often surprising how many people even professional car audio people will obsess about signal wire but routinely provide the amplifier only a fraction of the current it needs to do its job The most common wire gauge used in car audio is 10 gauge Gain control Proper gain setting is one of the most important factors in setting up a stereo system at the same time gain setting is most often done wrong Turning up the gain of an amp is the very last thing you should ever do to a system First hook up the system with all gain controls at minimum turn the gain pot fully counter clockwise with a small screwdriver Then turn on the head unit and turn up the
9. e returning the product for service e Enclose with the defective product a brief description of the problem with a name and daytime phone number so we may be in contact with any questions or concerns regarding the return e Enclose a copy of the original sales receipt for proof of purchase and installation e Enclose a 15 00 US certified check or money order to cover shipping and handling for return of the product Do not include cash Carefully pack the product to protect it from damage during shipping and send it prepaid to SoundStream Technologies 1550 S Maple Ave Montebello CA 90640 Attn Customer Service Ph 800 724 1377 Fax 323 722 8125 Please note the warranty will not cover the following Any product that has been misused or physically damaged _ Any product that has been installed incorrectly i e over powered incorrect enclosure incorrect wiring etc Any units that have been previously opened or repaired by a service center which is not authorized by SoundStream Technologies Any applicable implied warranties including the warranty of the merchants ability are limited in duration to a maximum of 2 years from the date of the original purchase at retail and no warranties whether expressed or implied shall apply to this product there after Under no circumstances shall SoundStream Technologies be liable for any loss or damage direct or consequential arising out of the use of or inability to use this product some stat
10. es do not allow for limitations of implied warranties or exclusion of consequential damage therefore these restrictions may not apply To receive the full benefit of this warranty fill out the included warranty card and mail it to the address shown Owners Registration Card Please complete and return immediately to the address on the reverse side Name Address City State Zip Vehicle Make Model Product Model Serial Number Date Purchased Name of Dealer Dealer Address City State Zip Phone Website
11. na output from the head unit to the remote turn on wire of the amplifier If the head unit is not equipped with a remote antenna output locate a wire that is controlled by the accessory position of the key It is important to have the amplifier turn off with the radio or key If the amplifier remains on the result will most likely be a dead battery 12V Connect the proper gauge power wire to the amplifier B terminal Run wire to wards the fuse holder that is no greater then 0 5 meters from the battery Remember the fuse is to protect the safety of the car in the case of a short Connect fuse holder to battery but do not install fuse at this time Power connection Power connection 1 1 Fl ese e lff 228 samor UU we o e A mwe a A emassis orouno GNO 12V CHASSIS GROUND GNO 12V BATTERY To costom radio Remote BATTERY To costom radio Remote MODEL NO PN4 320D MODEL NO PN1 450D PN4 520D PN1 650D Speaker connections g lt E s A 0 5 x 20 az 20 2 0 no Tit m
12. quency Response 20 150kHz e Signal to Noise Ratio 70dB e Damping Factor gt 100 e Input Sensitivity 200mV 6V 4 CH FUNTIONS MONO BLOCK FUNTIONS woe i n ow I X OVER ka FRONT JREAR GAR X OVER em SONIC Boost Pass mm dl HP 80H2 F 6v 025V 6v 0 25V FL sonz O JI AN waw wese A EE O 1 1 e 16 de FUSE POWER SPEAKER OUT FU sector 886 a of jan oe wo Y GND MODEL NO PN4 320D PN4 520D MODEL NO PN1 450D PN1 650D Warnings SOUND STREAM highly recommends that a fuse or circuit breaker be placed within 18 of the battery Although products have adequate internal protection it is possible that a pinched power wire between the component and the battery may result in a fire The protection device should be placed where it can be accessed easily and all wiring should be routed safely and correctly according to the following guidelines Do not run wiring close to hot or spinning objects Always use wire grommets when routing wire through the firewall or any other metal panels Make sure that the potential for pinched wiring is avoided by routing all wires away from moving hinges and seats This also includes brake gas and clutch pedals hood and trunk hinges et
13. rs Low pass Controls The amplifier is used to drive a subwoofer The frequencies above the crossover point will be attenuated at 12dB octave Permits adjustment of the crossover frequency by rotating the knob to select any frequency between 50Hz to 250Hz as the crossover point Remote Control Can control bass low tone according to your inclination Low tone of sound stream can hear deep and clean sound because control gain Caution Use line offered at factory Otherwise can be responsible for noise occurrence Remote control connection I Darse ee MODEL NO PN1 450D PN1 650D Sub sonic filter Control To protect your speakers we have designed a new sub sonic filter The filter is a 12dB octave high pass that is variable from 15 Hz to 50 Hz so you can match the filter to your woofer enclosure High Level input Connect speaker output from factory radio to amplifier To hear more clarity you must connect the chassis ground please High level input connection I cm mont ree a X OVER High level input connection I X OVER mm m Kanpur e MODEL NO PN4 320D MODEL NO PN1 450D
14. sound system s volume control to about one third of its full range 3 Adjust GAIN MIN MAX to a comfortable listening level 4 Turn up the auto sound system s volume control until the sound begins to distort Then immediately turn the volume down to a point just before where the distortion began Caution Never turn up the auto sound system s volume control more than needed to adjust the audio level more than two thirds of its maximum volume 5 Adjust GAIN MIN MAX until the sound is at the maximum level you want the amplifier to produce 6 Adjust the auto sound system s volume control to a comfortable listening level FREQUENCY RESPONSE with BASS BOOST ON 20dB 10dB 3 aii 0dB 35 80 N zZ Q 10dB N uy Z 20dB eee 10 45 100 500 1K 5K 20K 50K FREQUENCY Hz NOTE Raising the Bass Frequency allows higher frequencies to reach the bass speakers centered around 45Hz This BUMP can have a dramatic effect on the bass system s apparent volume Use caution When adjusting this control as serious subwoofer damage may result from overpowering or overexcursion Trouble shooting SYMPTOMS CHECK REMEDY Is the power Check all fuses to amplifier LED illuminated Be sure Turn on lead is connected NO Check signal leads Check gain control Check Tuner Deck volume level Clean contacts on fuse holders Is the Diagnostic Check for speaker short or LED illuminated
15. volume If you achieve clean sound and more volume than you want you don t need to make any adjustments However if you turn up the volume and begin to hear distorted sound before it becomes loud you are clipping distorting the deck probably a little over 34 volume Turn the deck down just enough to hear clean sound again and then move to the next component in your system With the deck playing at maximum clean volume adjust the gain of the next component to its maximum clean volume If you adjust your gains this way always starting at the head unit and working down the line to the amplifier you will get the most performance out of your amplifier s with the least amount of unwanted distortion and noise Cross over Controls All Picasso series amplifiers have electronic crossovers built in This allows you to build multi amp systems without the need for added electronic crossovers The HPF LP control allows the user to choose exactly what crossover frequency the amp will use Selectable switch for 80Hz High pass HP Full pass F 80Hz Low pass LP Bass Boost Control SOUND STREAM has provided all Series amplifiers with a variable Bass equalization circuit Each amplifier has a Bass Boost control which allows adjustment of the bass from OdB to as much as 18dB This adjustment is made at a frequency of 44Hz Use the Bass Boost with caution Too much equalization can easily cause amplifier clipping and may even damage your speake

Download Pdf Manuals

image

Related Search

Related Contents

EVGA PCoIP Zero Client  Tomo II - Programas de Infraestrutura.indd  ThunderSTORM: a comprehensive ImageJ plugin for PALM and  ZyXEL IES-612-51A User's Manual  QIClick User Manual  Barclay Products 4141-30-BN Installation Guide    Olympia 5907  1 Materials File Update  Downloads - Electrolux  

Copyright © All rights reserved.
Failed to retrieve file