Nilfisk E 140.3-9 X-TRA
Contents
1. SG Sg B3 Push the spray lance 6 into the spray handle 7 twist and release NOTE The spray lance has a built in low pressure nozzle that can be used for flushing away dirt B4 When attaching the nozzles 8 9 press the nozzles into the spray lance IMPORTANT When attaching the click amp Clean nozzles the pawl on the side of the spray lance should come out again The nozzle should stay in position when pulling it B5 Push the foam sprayer 10 into the spray lance 6 NOTE The foam sprayer features a swivel lock which must be positioned in the hole in the Click amp Clean spray lance Press the pawl to detach the Click amp clean nozzles and the foam sprayer IMPORTANT Before starting the cleaning job check that the machine is in an upright position and placed on an even surface Do not place the machine in long grass 4 3 Water Connection FO FS IMPORTANT Connecting to pressurized water supply The inlet water max pressure is 1 MPa 10 bar and the max temperature is 60 C see rating plate An ordinary 2 garden hose of min 10 m and max 25 m will be suitable B6 Check that the filter is fitted in the water inlet pipe and that it is not clogged up B7 Connect the water hose to the water supply by means of the quick connector Turn on the water Connection to the drinking water mains according to national and local regulations Let the water run through the water hose before connecting it to the machi2. and Click amp Clean nozzles d can be stored IMPORTANT The bearing capacity of the wall hook is max 30 kg Original Instructions 5 Fields of application and working methods 5 1 General Efficient high presure cleaning is achieved by following a few guidelines combined with your own personal experience of specific cleaning tasks Accessories and detergents when correct ly chosen can increase the efficiency of your pressure washer Here is some basic information about cleaning 5 1 1 Detergent and foam Foam or detergent should be applied onto dry surfaces so that the chemical product is in direct contact with the dirt Detergents are applied from bottom to top for example on a car body work in order to avoid super clean areas where the detergent collects in higher concentrati on and streams downwards Let the detergent work for several minutes before rinsing but never let it dry on the surface being cleaned Note It is important that the detergents do not dry up Otherwise the surface that has to be cleaned can be damaged 5 1 2 Mechanical effect In order to break down tough layers of dirt additional mechanical effect may be required Spe cial wash brushes offer this supplementary effect that cuts through dirt especially by car wash ing Original Instructions 13 EN 5 2 Typical fields of application Below you will find a description of a lot of cleaning tasks which can be solved by a pressure washer fr
3. Always unplug the power plug before cleaning or maintenance and when replacing parts or converting Original Instructions the machine to another function N e Observe the national safety regulations issued for example by the employers liability insurance associa tion social security institutions occupational safety and health authorities or other organizations A Accessories and spare parts e To ensure the machine safety only use original spare parts from Nilfisk or approved by Nilfisk e High pressure hoses fittings and couplings are impor tant for the safety of the machine Only use hoses fit tings and couplings recommended by Nilfisk VI Physical sensory or mental conditions e This machine is not intended for use by persons including children with reduced physical senso ry or mental capabilities or lack of experience and knowledge e Anyone who has consumed alcohol medicines or drugs affecting their ability to react must not operate the machine gt Applications This machine has been developed for domestic use such as e Car motorbike boat caravan trailer patio drive flag stones woodwork brickwork barbecue garden furni ture lawn mower Any other use is considered as improper use Nilfisk accepts no liability for any damage resulting from such use The risk for such use is borne solely by the user Proper use also includes proper operation servicing and repairs as specified in this in
4. maybe a brush You may use Stone brush Stone amp Wood Cleaner amp Wood Cleaner to remove moss and algae Garden tools lawn mover Tornado PR nozzle Power speed nozzle multiangle adaptor Metal Cleaner Rinse the worst dirt off with the nozzle Apply Metal Cleaner with the foam sprayer and let it act for approx 5 min Wash with the nozzle You may use the multiangle adaptor for hard to get at areas to avoid splashing Original Instructions 6 After using the pressure washer E ee ii C a U See the pictorial quick reference guide storing the high pressure washer The high pressure washer should be stored in a frost free room Should the machine by a mis take be frozen it will be necessary to check it for damages 6 1 Stopping the high pressure washer C1 Shut off the water supply and activate the trigger of the spray handle and let the machine run until no more water runs out of the nozzle This will wash out water hose high pres sure hose spray lance and nozzles C2 Stop the machine turning the start stop switch to position 0 C3 Unplug the machine from the power supply socket w IMPORTANT To avoid accidents the electric cable and the high pressure hose should always be wound up carefully C4 Wind up the electric cable on the dedicated cable hook 18 The upper hook can be turned to release the electric cable The upper hook has a built in clip for good holding of the el
5. 0 3 2 2006 A1 2009 A2 2009 EN 61000 3 11 2000 EN55014 2 1997 A1 2001 A2 2009 IEC 60335 1 2012 Applied harmonised standards Applied international standards and technical specifica tions IEC 60335 2 79 2012 Name and address of the person authorised to compile the technical file Anton Sgrensen General Manager Technical Operations EAPC Nilfisk Advance A S Sognevej 25 DK 2605 Br ndby frk finson Anton S rensen General Manager Technical Operations EAPC Identity and signature of the person empowered to draw up the declaration on behalf of the manufacturer Nilfisk Advance A S Sognevej 25 DK 2605 Br ndby Hadsund 01 10 2013 Place and date of the declaration 18 Original Instructions a Se Ka S N AZ N an SE W JEAN kt MN ZS N N A ga CEA AN Ze ALIN m A CM i Q SA F lt XA SS OR N N NGS SS TAN 10 19 17 3 18 Nilfisk http www nilfisk com HEAD QUARTER DENMARK Nilfisk Advance Group Sognevej 25 DK 2605 Br ndby Tel 45 4323 8100 E mail mail com nilfisk advance com SALES COMPANIES AUSTRALIA Nilfisk Advance Pty Ltd Unit 1 13 Bessemer Street Blacktown NSW 2
6. 148 Website www nilfisk com au AUSTRIA Nilfisk Advance GmbH Metzgerstrasse 68 5101 Bergheim bei Salzburg Website www nilfisk at BELGIUM Nilfisk Advance n v s a Riverside Business Park Boulevard Internationalelaan 55 B timent C3 C4 Gebouw Bruxelles 1070 Website www nilfisk be CHILE Nilfisk Advance de Chile San Alfonso 1462 Santiago Website www nilfisk com CHINA Nilfisk Advance Suzhou Building 18 Suchun Industrial Estate Suzhou Industrial Park 215021 Suzhou Website www nilfisk cs com CZECH REPUBLIC Nilfisk Advance VGP Park Horni Po ernice Do Certous 1 2658 193 00 Praha 9 Website www nilfisk cz DENMARK Nilfisk Advance NORDIC A S Sognevej 25 2605 Brondby Tel 45 4323 4050 E mail kundeservice dk nilfisk com FINLAND Nilfisk Advance Oy Ab Koskelontie 23 E 02920 Espoo Website www nilfisk fi FRANCE Nilfisk Advance 26 Avenue de la Baltique Villebon sur Yvette 91978 Courtabouef Cedex Website www nilfisk fr GERMANY Nilfisk ALTO eine Marke der Nilfisk Advance GmbH Guido Oberdorfer Stra e 2 10 89287 Bellenberg Website www nilfisk de GREECE Nilfisk Advance A E Avamavoewc 29 Kopwri T K 194 00 Website www nilfisk gr HOLLAND Nilfisk Advance Versterkerstraat 5 1322 AN Almere Website www nilfisk nl HUNGARY Nilfisk Advance Kereskedelmi Kft Il R k czi Ferenc ut 10 2310 Szigetszentmiklos Lakihegy Website www nilfisk hu INDIA Nilfisk Advance India
7. A E 130 3 E 140 3 145 3 User Manual EERHEEEEERECKHEKERSEK REGER User lees eege eer 3 18 BS DON Dog EE 19 34 KIS AU JO eise dee AE 35 50 InstruktionSbOK 4 4 4 4 25455 5555 015a Hal ARAN Kela A uk KAHR 51 66 Le IC 67 82 Te e lU EE 83 100 Instructions d utilisation seen 101 119 Gebruiksaanwijzing seen a 120 137 Istruzioni SUIP SO 354 3 545x4 mln Ka len e eban c E 138 155 Instrucciones EE 156 173 Instru es de operac o kk kk 174 191 OONVIEG e e 192 211 Kullan m Kdavuzu nenn 212 229 N vod k obsluze uaan na 230 245 Haszn lati Otmutaio kk kkk 246 262 Instrukcja KENE aa 263 279 Priru nik za KOSMIKO nn 280 296 SL Navodila za uporabo nennen 297 311 N vod na pouzhvanie nn 312 328 Lieto anas instrukcijae nn 329 345 Naudojimosi instrukcija EE 346 361 LEE EE Hl EE 362 377 eegene 378 396 HEVE WAN ee 397 409 Contents d introduction nedd Ee 4 1 1 Symbols used to mark Instruction 4 2 Safety precautions and working techniques nnuuresnneonnnannnnnnnnnnnnnnnnnnnnnnnn 4 3 Before you start using your high pressure washer 10 3 1 Mounting of trolley handle hose hook and hose reel 10 3 2 Mounting of quick coupling e kser cao ya kara k ye sas j n d lal kardan y Ay TA 1 Aka h n z nkA 10 33 Telescopic handle ee on dan v eier 10 4 Operating your high pressure washer uuusunsnnnnnnn
8. Limited Pramukh Plaza B Wing 4th floor Unit No 403 Cardinal Gracious Road Chakala Andheri East Mumbai 400 099 Website www nilfisk com IRELAND Nilfisk Advance 1 Stokes Place St Stephen s Green Dublin 2 Website www nilfisk com ITALY Nilfisk Advance SpA Strada Comunale della Braglia 18 26862 Guardamiglio LO Website www nilfisk it JAPAN Nilfisk Advance Inc 1 6 6 Kita shinyokohama Kouhoku ku Yokohama 223 0059 Website www nilfisk com MALAYSIA Nilfisk Advance Sdn Bhd Sd 14 Jalan KIP 11 Taman Perindustrian KIP Sri Damansara 52200 Kuala Lumpur Website www nilfisk com MEXICO Nilfisk Advance de Mexico S de R L de C V Agustin M Chavez No 1 PB oficina 004 Col Centro de Ciudad Santa Fe 01210 Mexico D F Website www nilfisk com NEW ZEALAND Nilfisk Advance Danish House 6 Rockridge Avenue Penrose Auckland 1135 Website www nilfisk com NORWAY Nilfisk Advance AS Bjornerudveien 24 1266 Oslo Tel 47 22 75 17 70 Website www nilfisk no POLAND Nilfisk Advance Sp Z O O ul 3 Maja 8 05 800 Pruszk w Website www nilfisk pl PORTUGAL Nilfisk Advance Sintra Business Park Zona Industrial Da Abrunheira Edificio 1 1 A P2710 089 Sintra Website www nilfisk pt RUSSIA Hundpuck 3aBaHc 127015 MockBa Batckaa yn 27 emp 7 Poccna Website www nilfisk ru SLOVAKIA Nilfisk Advance s r o Bancikovej 1 A SK 821 03 Bratislava Website www nilfisk sk S
9. OUTH AFRICA WAP South Africa 12 Newton Street Spartan 1630 Website www nilfisk com SOUTH KOREA Nilfisk Advance Korea Co Ltd 3F Duksoo B D 90 Seongsui ro Seongdong gu Seoul Korea www nilfisk co kr SPAIN Nilfisk Advance S A Torre d Ara Planta 9 08302 Matar6 Barcelona Website www nilfisk es SWEDEN Nilfisk Advance AB Taljegardsgatan 4 431 53 M lndal Website www nilfisk alto se SWITZERLAND Nilfisk Advance Ringstrasse 19 Kircheberg Industri Stelzl 9500 Wil Website www nilfisk alto ch TAIWAN Nilfisk Advance Taiwan Branch 1F No 193 sec 2 Xing Long Rd Taipei Tel 88 6227 002 268 Website www nilfisk alto tw THAILAND Nilfisk Advance Co Ltd 89 Soi Chokechai Ruammitr Viphavadee Rangsit Road Ladyao Jatuchak Bangkok 10900 Website www nilfisk co th TURKEY Nilfisk Advance A S Serifali Mh Bayraktar Bulv Sehit Sk No 7 Umraniye Istanbul Website www nilfisk com tr UNITED KINGDOM Nilfisk Advance Ltd Nilfisk House Bowerbank Way Gilwilly Industrial Estate Penrith Cumbria CA11 9BQ Tel 01768 868995 Website www nilfisk co uk UNITED ARAB EMIRATES Nilfisk Advance Middle East Branch SAIF Zone P O Box 122298 Sharjah Website www nilfisk com VIETNAM Nilfisk Advance Representative Office No 51 Doc Ngu Str Ba Dinh Dist Hanoi Website www nilfisk com
10. ade by a certified electrician and comply with IEC 60364 1 e It is recommended that the electrical supply to the machine should include a residual current device that will interrupt the supply if the leakage current to earth Original Instructions exceeds 30 mA for 30 ms En e Inadequate extension cables can be dangerous If an extension cable is used it shall be suitable for outdoor use and the connection has to be kept dry and off the ground e Nilfisk recommends use of an extension cable drum when cable extension is needed which keeps the socket at least 60 mm above the ground e Cables on extension cable drums should always be completely unwound to prevent overheating Exten sion cables must comply with the below mentioned re quirements for length and cable dimensions 1 0 mm2 Max 12 5m 1 5mm Max 20 0 m 25mm Max 30 0 m e f the electric cable is damaged it must be replaced by an authorized Nilfisk distributor or similar qualified person in order to avoid a hazard Water connection amp This high pressure washer is only allowed to be con nected with the drinking water mains when an appro priate backflow preventer has been installed Type BA according to EN 60335 2 79 The backflow preventer can be ordered under number 106411177 As soon as drinking water has flown through the back flow preventer it is no longer regarded as drinking water Operation by suction e g a rainwater vessel is car rie
11. by applying Stone amp Wood Cleaner with floors and Stone amp Wood the foam sprayer Wash before the soap dries Another other hard Cleaner more effective and quicker method is to use the Patio surfaces Patio Cleaner Cleaner Thus you will also avoid splashes Garden furni Wood Cleaner Apply Wood Cleaner and wash before the soap dries ture wood Garden brush NOTE Use the garden brush to clean off the dirt Brickwork Powerspeed Same method as for flagstones but be careful bad joints and Wood work nozzle wood may be damaged by high pressure You may choose only Stone amp Wood to use the Tornado nozzle Adjust the distance pressure to Cleaner the quality of the joints and the wood Patio Cleaner can also be Patio Cleaner used on vertical surfaces Gutter Underchassis spray Wash the gutter with the nozzle Always wash towards lance downpipes Beware not to spray under the roofing Cleaning of Tube cleaner Push the tube cleaner approx Y2 m to mark into a tube or drain drain pipes and activate the trigger of the spray handle The nozzle opening outlets down turning backwards will pull the cleaner through the tube The pipes etc nozzle will break down the plug and flush the dirt backwards Rust paint Water sandblasting Mount the water sand blasting equipment and rust and paint equipment is efficiently and quickly removed Beware not to damage the surface to be sandblasted Greenhouse Tornado PR nozzle Wash with high pressure and
12. d out without a backflow preventer see Connec ting to a pressureless water supply w IMPORTANT e Only use water without any impurities e f there is a risk of running sands in the inlet water i e from your own well an additional filter should be mounted Original Instructions 7 g A During work WARNING e Never use the machine in an environment where there could be a danger of explosions If any doubt arises contact the local authorities e It is not allowed to clean asbestos containing surfaces with high pressure e Never draw in fluids containing solvents e g gaso line heating oil paint thinner or acetone These sub stances damage the materials used in the machine Their spray is highly combustible explosive and poi sonous e Never direct the water jet at yourself other persons gt not even to clean clothing or footwear risk of injury e Never direct the water jet at pets or other animals e Never direct the water jet at live electrical equipment or the machine itself danger of short circuiting e Hold the spray lance firmly with both hands The spray lance is affected by a thrust of up to 16 4 N during operation e This high pressure washer machine must not be ope rated at temperatures below 0 C e Never start up a frozen machine Frost damages are not covered by the guarantee e Always ensure firm and safe footing e Keep the machine as far away as
13. ectrical cable C5 The high pressure washer comes in two models A with hook for storage of high pres sure hose 15 B with a hose reel 12 C6 Rinse the spray lance nozzles and the foam sprayer after use C7 Place spray handle f lance a nozzles b foam sprayer c in the holders on the high pressure washer The nozzle cleaning tool d and a Click amp Clean brush e can also be stored on the product 7 Maintenance D CH See the pictorial quick reference guide maintenance To ensure a long and problem free working life of the high pressure washer please take the following advices Wash out water hose high pressure hose spray lance and accessory before mounting Clean the connectors of dust and sand Rinse the detergent bottle and the detergent nozzle Clean the nozzle Keep the water inlet filter clean and unclogged e e e e e Cleaning of the water inlet filter D1 Clean the water inlet filter regularly once a month or more frequently according to use Carefully loosen the filter with a screwdriver and clean it Check that it is intact before remount ing it Cleaning of nozzle A clogging up in the nozzle causes a pump pressure which is too high why cleaning is re quired immediately w IMPORTANT The nozzle cleaning tool 11 should only be used when the nozzle is detached and the ma chine is stopped D2 Stop the machine and disconnect the nozzle Clean the nozzle Original Instructions 15 D3 Fl
14. etal tubes Make sure that the handle is mounted as illustrated Mount screws with nuts make sure that the screws go through handle as well as tube A2 Mount the hose hook 15 on the handle 2 screws Mounting of hose reel handle models with hose reel A3 Click the hose reel handle on to the trolley handle no screws 3 2 Mounting of quick coupling W A4 When mounting the quick coupling for the first time check that the factory fitted filter is positioned in the water inlet pipe A5 Screw the quick coupling tight on to the water inlet 2 IMPORTANT The inlet filter must always be fitted in the water inlet pipe to filter out sand limestone and other impurities as these will damage the pump valves The filter is factory fitted If the filter is removed this will invalidate the guarantee 3 3 Telescopic handle A6 The machine features a telescopic handle To raise or lower the handle press the button 17 and move the handle upwards or downwards When a click is heard the handle is in right position Original Instructions 4 Operating your high pressure washer amp B See the pictorial quick reference guide operating your high pressure washer 4 1 Connection of high pressure hose B1 Attach the high pressure hose 4 to the spray handle 7 Detach the high pressure hose by pressing the pawl A B2 Mount the high pressure hose on the outlet 3 4 2 Mounting of spray lance and Click amp Clean nozzles
15. ked with this symbol must be observed to prevent personal injury or serious damage to property Caution where there is a risk of damaging the machine or its individual components This symbol indicates tips and instructions to simplify work and to ensure a safe operation of the high pressure washer 2 Safety precautions and working techniques A Before starting up your machine for the first time this instruction manual must be read through carefully Save the instructions for later use WARNING e Inhalation of aerosols can be hazardous to health Where applicable use a device in order to avoid or re duce aerosols production e g a shield covering the nozzle For protection against aerosols use a respira tory mask of class FFP 2 or higher e The high water pressure generated by the machine and the power connection are particular sources of danger e Children should be supervised to ensure that they do not play with the machine e Before starting up your machine please check it care fully for any defects If you find any do not start up your machine contact your Nilfisk distributor The in sulation of the electric cable should be faultless and without any cracks If the electric cable is damaged an authorized Nilfisk distributor should replace it e The operator and anyone in the immediate vicinity of the site of cleaning should take action to protect them selves from being struck by debris dislodged during operation e
16. l Nilfisk distributor Recycling the high pressure washer Make the old machine unusable immediately e Unplug the machine e Cut the electric cable Do not discard electrical appliances with household waste As specified in WEEE Directive 2012 19 EC on old electrical and electronic appliances used electrical goods must be collected separately and recycled eco logically Contact your local authorities or your nearest dealer for further information Sat Original Instructions EN 3 Before you start using your high pressure washer A SX See the pictorial quick reference guide unpacking Illustration shows the operation elements and how to prepare your machine for use Operation elements Start stop switch Water inlet with filter High pressure connection models without hose reel High pressure hose Electric cable Click amp Clean spray lance Spray handle with lock 7a Click amp Clean Tornado PR nozzle Click amp Clean Powerspeed nozzle 10 Foam sprayer 11 Nozzle cleaning tool 12 Hose reel not standard 13 Model tag 14 Trolley handle telescopic handle 15 Hose hook 16 Hexagon key for handle and bracket mounting 17 Button for telescopic handle 18 Turnable cable hook 19 Quick coupling OONOOHXHON 3 1 Mounting of trolley handle hose hook and hose reel Mounting of trolley handle and hose hook standard models A1 Push down the trolley handle 14 over the two m
17. ne to prevent sand and dirt from penetrating the machine B8 Turn off the water and connect the water hose by means of the quick coupling to the wa ter inlet Connecting to pressure less water supply The machine can also operate in suction mode meaning that you can connect the machine to e g rainwater vessels rivers lakes and cisterns etc When taking in water from non drinking water mains the backflow preventer is not needed Original Instructions 11 When connecting the machine to operate from pressure less water supplies always use ad ditional filtering to secure that impurities are not sucked in Hose length should be max 3 meter and of minimum 1 2 To meet these requirements Nilfisk recommenas that you use the original Nilfisk suction hose kit The Machine is designed for suction up to 100 cm above water surface e Position the machine at max 1 0 meter above the water surface Detach the high pressure hose from the outlet e Ensure that the inlet filter is in position and attach the suction hose kit secure tight connec tion to the inlet Turn on the machine turning the start stop switch 1 to position I Wait until a steady jet exits the outlet Switch off the machine and attach high pressure hose 4 spray handle lance and nozzle Start the machine again and activate the spray handle e e e o 4 4 Starting the high pressure washer JE 4 5 Pressure IMPORTANT Connecting to mains power sup
18. nnnnnnnnnnnnnnnnnnnnnnnennnnnn 11 4 1 Connection of high pressure bose sesa ka kk kk k kak 11 4 2 Mounting of spray lance and Click amp Clean nozzles nennen 11 4 3 Water Connection sun wa e dane one e aw os sun Bin jara peri dee AA k Hei n 11 4 4 Starting the high pressure washer u 220u42nn0nnnnnennnnnennnnnennnnnennnnnennnnnannn 12 4 5 Pressure regulation on the TORNADO PDP nozzle ece 12 4 6 Stationary E 12 5 Fields of application and working methods zuunnnssusnnnnnnnnnnnnnnnnnnnnnn 13 5 1 General aen naher Miele ES ee eee deer 13 5 2 Typical fields of application 14 6 After using the pressure washer uunssnnnnnnnnennennnnnnnnnnnnnnnnnnnnnnnnnnnnnnneennn 15 6 1 Stopping the high pressure WASHEL 1 cccceccceeseeceeneecseneeeteneeetenenetenenetenenensaees 15 Z M infen nce u a ze ale 15 8 TFOUBIESKOOUNQ E 16 9 Accessories and detergentS 0000000rrrraaaaonnnonoorrnresenaaannnnnnonannonnanaannoononnnnnn 17 10 Warranty Conditions eege anti pea ine r a kk ness 17 11 Maintechnical Data i e oak avek anne kak kok kulak wa we be k k d k 17 12 Declaration Of Conformity uuuursennsnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnannnnnnnnnnnnnnnnnn 18 Original Instructions EN 1 Introduction 1 1 Symbols used to mark instruction A D I All pictograms attached to the high pressure washer and its components are shown and ex plained in this manual Safety instructions mar
19. om Nilfisk in association with accessories and detergents Task Accessories Click Cleaning method amp Clean Car Car nozzle 1 Apply Car Combi Cleaner with the foam sprayer Always auto brush start from the bottom and work upwards Let Car Combi underchassis Cleaner act for at least 5 min nozzle 2 Wash the car with the car nozzle which has been optimized for Foam sprayer quick and gentle cleaning of enamelled surfaces the jet is wider Car Combi Cleaner and not so sharp Start at the front ofthe car and work back wards to avoid water from penetrating by the door mouldings 3 Use the brush for removal of traffic film which is not removed by the nozzle If the car is very dirty apply Car Combi Cleaner again 4 Attach the undercarriage nozzle and clean undercarriage and wheel arches 5 Remove water from the surface of the car with the scraper on the car brush Make sure that all grains of sand etc have been removed before using the scraper Wipe with a wash lea ther where the scraper cannot reach Rims alumi Rim brush Apply Alu Cleaner with an automizer Let it act for approx nium auto nozzle 5 min and wash with the rim brush For steel rims use Car Com atomizer bi Cleaner Use the foam sprayer and wash with rim brush Alu Cleaner Be careful The high pressure jet may damage the tyres Flagstones Powerspeed Wash towards outlets or the like On surfaces with foulings you concrete nozzle may start
20. onditions e that defects are attributable to flaws or defects in materials or workmanship wear and tear as well as misuse are not covered by the guarantee that the directions of this instruction manual have been thoroughly observed that repair has not been carried out or attempted by other than Nilfisk trained service staff that only original accessories have been applied that the product has not been exposed to abuse such as knocks bumps or frost that only water without any impurities has been used that the high pressure washer has not been used for rental nor used commercially in any other way Repairs under this guarantee include replacement of defective parts exclusive of packing and postage car riage Besides we refer to your national law of sale The machine should be forwarded to one of the service centres of the Nilfisk organisation with description specification of the fault Repairs not covered by the guarantee conditions will be invoiced Le malfunctions due to Causes men tioned in section Troubleshooting Chart of the instruction manual e e e e o 11 Main technical Data Type E 130 3 E 140 3 E 145 3 Electric specifications Rated voltage V 220 240 220 240 220 240 Rated frequency Hz 50 60 50 60 50 60 Rated power consumption kW 2 0 2 1 2 1 Current A 9 0 9 5 10 Protection class Gen Ii Class Il Class Il Class II Protection degree IP xx IPX5 IPX5 IPX5 Hydraulic s
21. pecifications Rated pressure MPa bar 12 5 125 13 5 135 14 0 140 Max pressure MPa bar 13 0 130 14 0 140 14 5 145 Rated water flow l min l h 7 5 450 7 0 420 6 6 400 Max water flow l min l h 8 3 500 8 3 500 8 3 500 Max water inlet pressure Mpa bar 1 10 1 10 1 10 Max water inlet temperature C 60 60 60 Max water inlet temp suction mode C 20 20 20 Weight kg 17 8 18 6 19 8 ek according to ISO 5349 1 m s2 lt 2 5 1 lt 25 41 lt 25 1 Machines without hose reel Sound pressure level LpA in accordance with ISO 3744 dB A 66 8 2 66 8 2 Guaranteed sound power level LWA in accordance with 82 82 2000 14 EC Machines with hose reel Sound pressure level LpA in accordance with ISO 3744 dB A 71 8 2 71 8 2 Guaranteed sound power level LWA in accordance with 86 86 86 2000 14 EC We reserve the right to make alterations Original Instructions 17 EN 12 Declaration of Conformity C Declaration of Conformity Product High Pressure Washer Type Nilfisk E 130 3 E 140 3 E 145 3 and accessory variants of above mentioned types Description 220 240 V 1 50 60 Hz IP X5 The design of the unit corresponds to the following EC Machine Directive 2006 42 EC pertinent regulations EC Low voltage Directive 2006 95 EC EC EMC Directive 2004 108 EC RoHS Directive 2011 65 EC EC Noise Emission Directive 2000 14 EC EN 60335 2 79 2012 EN 62233 2008 EN 55014 1 2006 A1 2009 A2 2011 EN 6100
22. ply The voltage and frequency of the machine see model tag 13 must match the voltage and frequency of the power supply Connecting the high pressure washer to a supply system the max allowed impedance is 0 29 j0 18Q Zmax Consult with the supply authority that the equipment is connected only to a supply of that impedance or less B9 Insert the power plug into power supply socket B10 Turn on the water B11 Release the trigger lock 7a Remember to unplug turn off the high pressure washer and lock the trigger when leaving the high pressure washer unattended B12 Activate the trigger of the spray handle and let the water run until all air has escaped from the water hose B13 Turn on the machine turning the start stop switch to position I B14 Activate the trigger of the spray handle When releasing the trigger of the spray handle the machine automatically stops The machine will start again when you reactivate the trigger of the spray handle regulation on the TORNADO PR nozzle B15 The pressure can be regulated on the TORNADO PR nozzle 4 6 Stationary use B16 If mounting a special wall hook not standard the pressure washer can be used as a stationary solution meaning that it can be operated while hanging on the wall Only mount the wall hook on a sturdy wall Adjust the length of the screws and size of rawlplugs to the type of wall B17 On the wall hook garden rim brush a foam sprayer b Click 8 Clean brush c
23. possible from the object being cleaned e Always adjust the distance and thus the pressure of the nozzle to the surface which is to be cleaned to avoid any damage to the surface being cleaned The machine shall be operated in an upright position e Do not cover the machine or use itin a room without adequate ventilation e f the machine is left or not used for 5 minutes it must be switched off on the start stop switch O 1 Original Instructions After finishing the work A WARNING e Always switch off the machine and unplug the power plug from the socket after work and when leaving the machine unattended e Disconnect water inlet hose between machine and water supply e Wind up electrical cable and high pressure hose to avoid damage of cable plug high pressure hose and fittings e Always empty pump hose and accessories of water after use of the machine and prior to storing Maintenance and repairs A WARNING e Always disconnect the electrical plug from the socket prior to maintenance cleaning and repair e Any repair should always be made in Nilfisk authorized workshop with original Nilfisk spare parts e Do not attempt any maintenance not described in the instructions e lf the machine refuses to start stops pulsates pres sure fluctuates motor busses fuse blows or no wa ter comes out check the trouble shooting diagram in these instructions In case other problems occur please contact your loca
24. struction Clothing and equipment Always take action to protect yourself when operating the machine Wear shoes with non slip soles Wear goggles ear protection and protective clothes during operation Original Instructions 5 Transporting the high pressure washer When transporting the machine in or on a vehicle it must be secured e g with straps so that it cannot slip or tip over e Nilfisk recommends that the machine is positioned horizontally on the backside when transported in or on a vehicle Detergents e This machine has been designed for use with clean ing agents supplied or recommended by Nilfisk The use of other cleaning agents or chemicals may ad versely affect the function of the machine Before starting the work Inspecting the machine e Do not use the machine if a supply cord or important parts of the machine are damaged e g safety de vice high pressure hose and spray handle and spray attachments e The trigger of the spray handle must move easily and automatically return to its starting position when re leased e Always keep high pressure hose and spray attach ment in good condition clean moving easily and cor rectly assembled Electrical connection WARNING Minimize the risk for electrical shock e Voltage and frequency of the machine see rating plate must match the voltage of and frequency of the mains supply e Only connect the machine to electrical installation m
25. ulsating Air in inlet hose pump Inadequate supply of mains water Nozzle partially blocked Water filter blocked Hose kinked Allow machine to run with open trigger until regular working pressure resumes Check that the water supply corresponds to specifications required see model tag NB Avoid using long thin hoses min 1 2 Clean the nozzle see section 7 Clean the filter see section 7 Straighten out hose Machine often starts and stops by itself Pump spray handle is leaking Contact your nearest Nilfisk Service Centre Machine starts but no water comes out Pump hoses or accessory frozen No water supply Water filter blocked Nozzle blocked Wait for pump hoses or accessory to thaw Connect inlet water Clean the filter see section 7 Clean the nozzle see section 7 In case problems other than the above occur please contact your local Nilfisk distributor Local Nilfisk distributors are listed on the back cover of this instruction Customer Service at Penrith 01768 868995 Original Instructions 9 Accessories and detergents Only use original accessories and detergents For further information see www nilfisk com 10 Warranty Conditions Nilfisk guarantees high pressure washers for domestic use for 2 years If your high pressure washer or accessories are handed in for repair a copy of the receipt must be enclosed Guarantee repairs are being made on the following c
26. ush the nozzle backwards with water Cleaning of machine vents D4 The machine should be kept clean so as to let cooling air pass freely through the machine vents Greasing of O rings D5 To ensure an easy connection and that O rings do not dry up the couplings should be greased regularly 8 Troubleshooting To avoid unnecessary disappointments you should check the following before contacting the Nilfisk service organization Symptom Machine refuses to start Cause Machine not plugged in Defective socket Fuse has blown Defective extension cable Recommended action Plug in machine Try another socket Replace fuse Switch off other machines Try without the extension cable Fluctuating pressure Pump sucking air Valves dirty worn out or stuck Pump seals worn out Check that hoses and connections are air tight Clean and replace or refer to local Nilfisk distributor Clean and replace or refer to local Nilfisk distributor Machine stops Fuse has blown Incorrect mains voltage Thermal sensor activated Nozzle partially blocked Replace fuse Switch off other machines Check that the mains voltage corresponds to specification on the model tag Leave the washer for 5 minutes to cool down Clean the nozzle see section 7 Fuse blows Fuse too small Change to an installation higher than the amp consumption of the machine You may try without the extension cable Machine p
Download Pdf Manuals
Related Search