Havis C-3090-4 car kit
Contents
1. 9 e The map light bracket will bolt to C 3090 on the same frame rail as the support tabs bolt to e Determine exact positioning with laptop mounted on C 3090 e Attach C ML MLB to C 3090 tab rail using 14 20 x 3 2 carriage bolts and nylock nuts e Wire map light according to instructions provided Photo 9 Mounting location C 3090_INST_6 09 docx6 092. Havis Inc 75 Jacksonville Road PO Box 2099 Warminster PA 18974 HAVI S T 800 524 9900 F 215 957 0729 Productivity in motion www havis com INSTALLATION INSTRUCTIONS C 3090 s amp C 3089 s COMPUTER LAPTOP MOUNT AND ACCESSORIES TOOLS NEEDED Ratcheting wrench Allen wrench set Standard socket set Screwdriver set Open end wrench set Always gt Read all instructions before installing any Havis Inc products gt Check for obstructions Wire brake lines fuel tank etc before drilling any holes gt Use hardware provided with install kit 1 MOUNTING C 3090 3 or 4 amp C 3089 3 or 4 to C TCB S e Photo 3 on page 2 is a basic assembly instruction of a C 3090 3 w tilt swivel mounting to a C TCB x e The tilt swivel assembly Photo 1 which comes pre assembled to the C 3090 from the factory will bolt directly to the rotating plate using the hardware loosely attached to the plate You do not need to unassembled the tilt swivel from the C 3090 Note Be sure the 2 fender washer ts assembled between the rotating plate and the tilt swivel assembly 2 C 3090 1 or 2 amp C 3089 1 or 2 MOUNTING TO VEHICLE TUNNEL PLATES e The C 3090 will come pre assembled with tilt swivel attached e Mount trak kit into vehicle e Place console and C 3090 into desired position on trak Photo 2 Note Be sure assembly does not interfere with dash or console e Slide 4 20 hex nuts into slots on side of trak in loc
3. ation to mount C 3090 e Attach C 3090 to trak using 4 20 x 1 2 hex Photo 2 bolts and washers Tighten in desired area Pa Step 1 Open up extend plates of TCB swivel assembly Step 2 Undo flex lock nut and washer and remove Leave washer on and hold screw in position with finger Step 3 Put computer mount on top Put on washer and flex lock nut and tighten to desired tension Photo 3 Laptop plate and orn ee mounting Universal laptop oe are Hegel plate shippe la en i Use 3 16 pre assembled igi Ai nene j for tension Computer tilt adjustment swivel bracket _if necessary C 3090 3 shown 9 For other computer mounting brackets Front see Consolidator of Parts Price Guide vehicle A See Arm tension adjustment page for instructions if necessary Tools Needed 3 16 Allen wrench 1 2 combination wrench 3 ADJUST C 3090 PLATFORM FOR SPECIFIC LAPTOP e The C 3090 will need to be adjusted to properly hold your particular laptop Note Do not adjust the latch on the underside of the laptop e Loosen the L clamps on the sides of the C 3090 Photo 4 e Release the latch on the underside of the laptop e Place laptop on top of C 3090 platform and close the latch e Open laptop and adjust L clamps so they are firm against inside lip of computer on the latch side e Loosen 4 20 nylock nuts on the plate on underside of laptop assem
4. bly and adjust to width of laptop C 3090_INST_6 09 docx6 09 e Adjust L brackets to clamp the laptop firm e Release latch and test for strength Adjust if necessary Photo 5 4 PLATFORM WIDENING INSTRUCTIONS Photo 5 e On larger laptops it may be necessary to use a different hole pattern on the plate e Remove 1 in photo 5 4 nylock nuts and washers e Remove 2 in photo 5 bracket and use alternate mounting holes to create a wider platform 5 OPTIONAL SCREEN SUPPORT C SS amp C SS 2 Photo 6 With laptop adjusted for C 3090 open screen on computer With screen open remove 4 20 nylock nut from L tab holding laptop Loosely attach optional screen support as shown Adjust screen support around screen and tighten hardware Test screen movement Photo 6 C 3090_INST_6 09 docx6 09 6 MOUNTING C TMLOCK e Photo 7 shows the C TMLOCK option which comes assembled from the factory if ordered with the C 3090 e Remove 8 32 keps nuts that hold down OEM latch on laptop computer mount e Remove Pem studs from laptop computer mount and replace with Pem studs included with C TMLOCK assembly e Move latch out of way and place C TMLOCK over Pem studs Place latch over top of C TMLOCK e Install keps nuts and tighten Photo 7 7 MOUNTING C ML MLB TO C 3090 Photo 8 amp
Download Pdf Manuals
Related Search