Gorenje G6N4AX
Contents
1. 6 Operating the electric Cooking 20 8 Operating the gas 9 Cleaning and 10 Special warnings and fault reporting 11 15 12 Connecting the appliance to the power 15 Connecting the cooking hob to the gas supply 16 14 02218 18016 soniri aaia 19 Technical 20 e Installation of the appliance into a kitchen worktop and its connection to the power mains and the gas supply may only be performed by an adequately qualified technician e When the appliance is in use additional heat and moisture are emitted into the room When the appliance is used for a prolonged period of time at a high performance level intensive ventilation or use of kitchen hood may is required in the room where the appliance is installed Do not use the gas burners if the flame seems unstable If you smell gas in the room immediately close the gas supply valve either on the gas bottle or gas pipeline extinguish all sources of open fire including cigarettes aerate the room do not turn on any electric appliances and call a natural gas expert e The main gas supply valve should also be closed if gas2. 252569 Technical characteristics Rating plate XXXXXX XXXXXX XXXXXX XXXXXX XXXXXX XXXXXX A BC D E F G H Serial number Model Type Trademark Code Technical information Compliance indications symbols Factory settings for gas type WE RESERVE THE RIGHT TO MAKE ANY CHANGES THAT DO NOT AFFECT THE FUNCTIONALITY OF THE APPLIANCE PVK_KVK 62 42K 06 12 252569
3. layer of detergent on a dry and cool surface and rub gently in the direction of surface treatment pattern Use a damp cloth and a detergent to clean stubborn stains then use a dry cloth to achieve to polish the surface until glossy Do not use the same stainless steel detergents to clean aluminum parts 1 Burner crown cover 2 Burner crown 3 Thermo element only with protected burners available only in some models 4 Ignition plug e Use warm water with some dishwashing detergent to clean the area around the cooking rings or hotplates Before doing so use a sponge to soften any stubborn residues e All dirty cooking zones should be cleaned thoroughly immediately after use If the cooking zones are less stained it suffices to wipe them with a damp cloth soaked in water and some detergent If the hotplate is heavily soiled use a steel sponge wire scrubber soaked with detergent After cleaning the cooking zones should always be wiped dry e Salt containing liquids dishes that have boiled over or moisture can damage the cooking zones Therefore always wipe the cooking zones clean and dry e To condition the cooking zones occasionally use some sewing machine oil or conventional products for cleaning and care available in the market Never use butter bacon lard or similar substance risk of corrosion If the cooking zone is slightly warm the detergent will penetrate the pores more quickly e Hotplate rings are made o
4. perform any repairs by yourselves Leave such tasks to an expert or an authorized service unit In case of minor faults or problems with the appliance operation check the following instructions to see whether you can eliminate the causes by yourselves Important A visit by a service technician during the warranty period will be charged if the appliance is not functioning because of improper use Store these instructions in a place where they are always readily accessible if pas the appliance on to another person the instructions should also be included Following is some advice on rectifying some common problems 252569 698486 The flame is uneven unstable wrong gas power setting pipeline suddenly changes kitchen hob kitchen hob The flame is extinguished Knob pressed too short or to Keep the knob depressed for shortly after ignition weakly a longer period of time Before releasing it pres it harder The grid has discolored inthe This is a commonplace Clean the grid with a metal care burner area phenomenon resulting from detergent high temperature Electric power supply in general The fuse may be blown Check the fuse in the fuse box is interrupted and replace it if it is blown Electric ignition of the burners There are food or detergent Open and carefully clean the no longer works residues between the spark opening between the spark plug plug and the burner and the burner If the burner cover look
5. 260 mm e Operate the cooking zones using the knobs built into the control panels e When at least one cooking zone is turned on the yellow LED is lit up e Power levels are indicated with the numbers from 1 to 6 on the control knobs The respective levels are selected stepwise The step knobs can be rotated in both directions e The cooking zone may be turned off three to five minutes before the end of cooking in order to make use of the residual heat and save some energy the following table lists some examples for using individual power levels 0 Cooking zone turned off 13 Maintaining the temperature and reheating of smaller quantities of food 3 or longer cooking of larger quantities 4 Consecutive cooking frying e g omelets etc 5 Deepfrying S 6 Quickheating 00000000 Ignition and operation of Models with two gas burners the burners e Operate the gas burners using the knobs the hob Power levels are indicated on the knobs by large and small flame symbols see section Appliance description e Rotate the knob through the large flame position 0 to the small flame position and back Operation interval lies between the two flame symbols e Gas burners be ignited using the electric spar plug built into each gas burner only available with some models IN Before rotating the knob it should first be depressed Single handed ignition 2 e In order to ignite the
6. MT IE GB 699090 Combined gas built in cooking hob Dear customer Instructions for use Instructions for connection Rating plate Combined and gas built in hob is intended for use households Our products are packed in environment friendly materials which can be recycled disposed of or destroyed without imposing any burden on the environment Instructions for use are intended for the user They describe the appliance and its operation The instructions apply to various types of appliances and may therefore include description of functions that may not be available on your appliance These instructions are only valid of the country symbol is indicated on the appliance If there is NO county symbol in the appliance technical instructions should be observed for adapting the appliance to comply with the requirements and regulations for use in your country The appliance must be connected in compliance with the instructions attached to it as well as in compliance with relevant regulations and standards The connection may only be performed by a qualified person The rating plate indicating the basic information on the appliance is attached to the lower side of the hob Important warnings nnne 3 Appliance description 4 COOKING ZO CS
7. burners will be out of use for a long period of time e g when going on holiday Do not leave small children unattended when the appliance is in operation Risk of burning and scalding e During cooking the overheated fat or oil on the hob may ignite There is a risk of burning and fire therefore control the cooking process at all times e Do not use the cooking hob for room heating Do not place empty pans on the hob Make sure that the parts of the burners are correctly positioned installed e In case of a failure of the appliance immediately disconnect the appliance from the power mains and contact the service center e Do not use steam cleaners or high pressure cleaners to clean the cooking hob as this may result in an electric shock e The appliance is manufactured in compliance with the relevant effective safety standards Nevertheless we strongly recommend that persons with impaired physical motoric or mental Capacity or persons with inadequate experience or knowledge do not use the appliance unless attended by a qualified person The same recommendation applies when the appliance is used by persons of less than legal age e After a prolonged use of cast iron plates the area of the plate and the edge of the cooking zone may discolour Repair service is not covered by the warranty e Caution Using a gas appliance for cooking results in generation of heat humidity and combustion products in the room where the applian
8. ce between the cooking hob and the kitchen hood should be no less than indicated the instructions for kitchen hood installation The minimum distance is 650 mm e The distance between the appliance edge and the adjacent tall kitchen furniture element should amount to no less than 100 mm e Use of massive wood decoration plates or boards on the worktops behind the cooking hob is permitted if the minimum distance remains the same as indicated in the installation drawings e Minimum distance between the built in cooking hob and the rear wall is indicated on the installation drawing e Cooking hobs be installed into worktops that are 30 to 50 mm thick Kitchen worktop cutoff Type KVK4 PVK4 dimensions Type KVK6 PVKG6 252569 698686 30 50 Only type EVP4 EVP2 ovens fitted with a cooling fan may be installed underneath this cooking hob Before installing an oven the rear wall of the kitchen furniture element should be removed in the area of the cooking hob cutout Furthermore a gap of at least 6 mm should be left at the front side The worktop should be installed completely horizontally The cutoff surfaces should be appropriately protected Attach the fastening elements 4 with the supplied screws 4 to the front and rear wall of the cooking hob and the worktop cutoff Connect the cooking hob to the power mains and gas supply see instructions for connecting a cooki
9. ce is installed Please make sure the kitchen is well ventilated especially during the use of appliance Make sure the natural ventilation openings are open or install a mechanical ventilation device ventilation hood Caution The appliance is intended exclusively for cooking The appliance may not be used for any other purpose such as heating of spaces The symbol on the product or on its packaging indicates that this product may not be treated as household waste Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of thisproduct For more detailed information about recycling of this product please contact your local city office your household waste disposal service or the shop where you purchased the product 252569 698686 Appliance description equipment depending on the model Upper side of a combined cooker with Upper side of a combined cooker with gas and electric cooking zones gas cooking zones Type KVK4 Type PVK4 Cooking zone rear left Cooking zone front left Control knobs Cooking zone front right Cooking zone rear right ar ON Control knob Electric Gas depending on the model power levels gas va
10. e desired pressure is reached The cooking zone should initially be set to the maximum power level as the pressure rises use the sensors to decrease the power level according to the pressure cooker manufacturer s instructions Make sure there is always enough water either in a pressure cooker or in any other piece of cookware as using an empty pan on the cooking hob will result in overheating which will damage both the pan and the cooking zone Tempered glass Pyrex cookware with a specially brushed bottom is suitable for use on cooking hobs if it fits the diameter of the cooking zone Cookware with larger diameter may break due to thermal stress When using any special or unconventional cookware follow the cookware manufacturer s instructions Energy saving Important warnings Pan bottom diameters should match the diameter of the cooking zone If the pan is too small some heat is wasted furthermore using a too small pan can damage the cooking zone Whenever possible given the cooking process use a lid The pan should be appropriately sized given the quantity of food prepared Preparing a small quantity of food in a large pan will cause a waste of energy Dishes that take a long time to cook should be prepared in a pressure cooker Various vegetables potatoes etc can be cooked in a small quantity of water however the lid should be closed tightly When the water is brought to boil reduce the power level to a setti
11. f stainless steel due to thermal load during cooking they may discolor slightly to yellow This phenomenon is a result of physical processes Yellow spots can be restored by conventional metal cleaning detergents Gas cooking zones Do not use aggressive utensils for cleaning the dishes as these will scratch the rings To clean the grid cooking hob surface and parts of the burner use hot water with some dishwashing detergent Clean the thermo element and the spark plug with a soft brush These parts must be kept impeccably clean as only then will they operate correctly Clean the crown and the burner cover Be particularly careful to keep all exit slots on the crown clean and unobstructed After cleaning dry all parts thoroughly and replace or reassemble them correctly Parts that are placed askew will make lighting the burners more difficult Warning Burner covers are coated in black enamel Due to high temperatures discoloration is unavoidable however this will not affect the operation of the burners During the warranty period only a service center authorized by the manufacturer may carry out any repairs Before making any repairs make sure the appliance is disconnected from the power mains either by removing the fuse or by disconnecting the power plug from the wall outlet Unauthorized tampering with and repairs of the kitchen range cooking hob can result in electric shock or short circuit hence do not attempt to
12. gas burner press the selected burner control knob and rotate it to the maximum power flame position An electric spark will be generated automatically igniting the releasing gas e If the electric ignition should not work due to a power failure or damp spark plugs the gas can also be ignited using a match or a gas lighter After igniting the gas keep the control knob pressed for another ten seconds until the flame settles e The flame can then be set between the maximum and minimum level Any setting between and is not recommended as the flame is not stable in this interval and may be extinguished If the burner hasn t ignited after the knob has been depressed for fifteen seconds close the burner and wait at least one minute Then repeat the ignition process If the burner flame is extinguished for any reason close the burner and wait at least one minute before attempting to re ignite it e To extinguish the flame and close the burner gas supply rotate the control knob to the right to the OFF position 252569 698486 Clean the appliance using warm water liquid detergent and a soft cloth Do not use any abrasive or sharp utensils or other objects Burnt or dried food residues should be moistened using a damp cloth and softened with appropriate detergent Stainless steel parts should be cleaned using special purpose detergents Use a dry highly absorbent cloth to apply a thin
13. l flexible pipe J After connecting the gas hob check the joints for any leaks Gas supply connection plug A EN ISO 10226 1 2 or EN ISO 228 1 Depending on the country specific connection regulations connection plug Non metal gasket with thickness of 2 mm C Pipe adapter for liquid gas Depending on the country specific connection regulations After the connection check the burners for correct operation The flames must be clearly visible and should be blue and green at the center If the flame is unstable increase the minimum power Explain the use of the burners to the user and read the instructions for use together e The procedure or adaptation of the cooker to another type of gas does not require removal of the appliance from the worktop e Before adapting disconnect the appliance from the power mains and close the gas supply valve e Replace the existing nozzles for nominal thermal load with corresponding nozzles for the new gas type see table below e When adapting the appliance to liquid gas fasten the 252569 698686 Adjustment elements regulation screw for minimum thermal load as far as it will go in order to attain minimum thermal load When adapting the appliance to natural gas release the minimum thermal load regulation screw in order to attain minimum thermal load but do not rotate it by more than 1 5 turns Cooker burner ah WN Burner crown cover Burner crown with cover sup
14. lve is closed E maximum power minimum power 252569 698486 Before using the appliance for the first time Important warnings Cookware A Electric cooking zones Turn on the cooking zones for 3 to 5 minutes and select the maximum power level some fumes may be discharged from the hob This way the protective cover on the cooking hob will reach its maximum solidness Do not turn on a cooking zone without a pan over it and never use the cooking hob for room heating Make sure the cooking zones and pan bottom are clean and dry and that sufficient heat transmission is enabled between them in order to prevent any damage to the heating surface Any fat or oil left on the cooking ones may ignite Therefore be careful when using fat and oil to prepare food e g French fries Do not place a damp pan or a steam covered lid on the cooking zones as moisture is detrimental to them Do not leave a hot pan to cool down on the cooking zones because moisture will be generated under it causing corrosion Tips for using the cookware Use high quality cookware with a flat and stable bottom Transmission of heat is best when the pan bottom and the cooking zone are of the same diameter and the pan is placed on the middle of the cooking zone When using a tempered glass Pyrex or porcelain cookware please follow the cookware manufacturer s instructions When using a pressure cooker do not leave it unattended until th
15. ng hob on a power network and gas supply For screwing down the fixing clip it is not allowed to use screws longer than 6 5 mm Type KVK4 PVK4 e Attach the supplied adhesive seal the lower edge of the cooking hob do not glue the gasket over the front support bracket Type KVK6 PVK6 e Attach the supplied adhesive seal on the lower edge of the cooking hob e Insert the cooking hob into he cutoff and press it heavily from above towards the worktop Important warnings e The appliance may only be connected by an authorized skilled technician e Electric system protection should comply with all relevant regulations e The connection clips be accessed when the connection clip covers are opened removed e Before connecting the appliance make sure the voltage indicated on the rating plate is consistent with the voltage in your home circuit e The rating plate with basic information is attached on the lower side of the hob e The electric circuit should also include an omnipolar switch that will separate the appliance from the mains if required with at least 3 mm of distance between contacts Suitable devices include fuses current protection switches etc e The connection should be selected according to the installation possibilities with regard to current and fuses e Given the protection from the risk of fire appliances of this type may be installed in a worktop next to a piece of kitchen furniture tha
16. ng that maintains a temperature just above boiling point B Gas cooking zones ah WN If you wish to quickly fry some food set the gas burner to the maximum power initially and reduce the power as your continue In all models the cooker burners are fitted with thermoelectric safety devices If the burner flame is extinguished due to boiling over draft etc gas supply will be shut off automatically Any chance of gas leaking into the room is eliminated Gas burner cover should always be placed very carefully on the burner crown Make sure the slots on the burner crown are never obstructed Burner crown cover Burner crown with the support for the burner cover Thermo element Spark plug Nozzle 252569 698486 Cookware e Correctly selected cookware will enable optimum cooking time and gas consumption Pan diameter is the most important parameter Flames that reach over the edge of a pan that is too small can damage the cookware furthermore gas consumption is higher in such cases e For combustion the gas also needs air If a pan is too large air Supply to the burner is insufficient as a result combustion effect is lesser Grid extension only available with some models Use the extension when using a pan of a smaller diameter Place the extension on the grid above the auxiliary burner Burner type Large 3 0kW 220 260 mm Normal 1 9kW 160 200 mm Auxiliary 1 0kW 120 140 mm Triple 3 5kW 220
17. onding measuring device e Connection cable on the back of the appliance should be led such way that it does not touch the appliance back wall as this part will get very hot during operation 252569 698686 Connection bridges are already installed on their respective places on the clip Screws of the connection terminals are open which means they do not have to be unfastened or unscrewed any further When fastening the screws you may hear a slight click which means that the screws should be fastened screwed in completely The following can be used for connection 5 RR F 4x1 5 rubber connection cables with a green yellow protective wire Type 5 VV F 4x1 5 PCV isolated connection cables with yellow green protective wire or other equivalent or superior grade cables Connecting the cooking hob the gas supply Important warnings e The appliance must be connected in compliance with all relevant regulations and it may only be used in well ventilated aerated rooms Before connecting or using the appliance please read the instruction manual e Before installing and connecting make sure the local natural gas supply network and connection type of gas and pressure are compatible with your appliance version e The version of this appliance is indicated on the rating plate e This appliance is not suitable for connection to a burning fumes exhaust s
18. port Thermo element Spark plug Nozzle Triple burner 5 Nozzle To leave the adjustment elements accessible please observe the following instructions Remove the support grid and burner covers with respective crowns In double burners adjustment elements are accessible behind the main nozzle protective plate Remove the control knobs including the gaskets Gas valve Minimum thermal load regulation valve Natural Wo 45 7 54 7 m Natural gas Natural gas E Wo 40 9 54 7 MJ m G20 20 Liquid gas 3B P Wo 72 9 87 3MJ m G30 p 30 mbar kw Consumption l h Nozzle type 1 100mm Nozzle code Nom therm load kW Consumption I h Nozzle type 1 100mm Nozzle code e Regulation valves that are factory built in are intended for liquid gas however the valves are set for operation with the type of gas for which the appliance is factory preset e When adapting the appliance for use with another type of gas the regulation screw valve should be fastened or release to correspond with the required gas flow throughput however the regulation screw should not be released more than by 1 5 rounds from the position in which it is completely fastened Burner power is indicated by observing the upper Hs caloric value Warning these tasks may only be carried out by a qualified technician authorized by the gas distributing company or authorized service center
19. s Regular dirt Clean the burner covers with a unappealing metal care detergent If the problem persists despite observing the instructions above call an authorized service technician Elimination of any errors or warranty claims that resulted from improper connection or use of the appliance is not covered by our warranty In such cases the costs of repair are borne by the user Important warnings e Installation of the appliance into a kitchen worktop and its connection to the power mains may only be performed by an adequately qualified technician e Veneer or other finish of the piece of kitchen furniture into which the hob is to be built in should be treated with heat resistant glue 100 C otherwise the worktop finish may be discolored or deformed e Cooking hob is dimensioned to be built into the worktop over a piece of kitchen furniture with a width of 600 mm or more e After installation the front two fastening elements should be freely accessible from below e The kitchen furniture element underneath the hob should not be fitted with a drawer If the kitchen furniture element as a horizontal partition wall it should be installed no less than 10 centimeters from the lower surface of the worktop The space between the partition wall and the hob must be empty no objects should be placed into that gap e Hanging or wall mounted kitchen elements should be installed high enough not to interfere with the work process e The distan
20. t is taller than the appliance when installed however in this case a kitchen furniture element must be installed on the other side adjacent to the appliance e The current conducting and isolated parts must be protected from any possibility of direct contact WARNING e Before any intervention disconnect the appliance from the power mains Connect the appliance in compliance with the electric connections diagram supplied make sure the relevant network voltage is observed The ground wire PE should be connected to the clip indicated by the earthing symbol e The mains cable should be fed through the fastening clip which protects it from being accidentally pulled out e After connecting the appliance turn all cooking zones heaters for approximately three minutes to make sure they are operating correctly Connection diagram The appliances are suitable for photovoltaic electrical power under the condition that electrical voltage will be 220VAC 240VAC with semi tonic frequency 50Hz in order the appliance to operate properly alternative a generator can be used with the same technical characteristic e Incorrect connection may destroy parts of the appliance making the warranty void e Before connecting the appliance make sure the voltage indicated on the rating plate is consistent with the voltage in your home network Connection voltage 230 V through N should be checked by a qualified technician using a corresp
21. ystem i e a chimney The appliance must be installed and connected in compliance with the relevant effective installation regulations Special care must be taken to ensure adequate ventilation aeration Connection e When connecting the appliance to the gas supply follow the regulations of the local gas distributor Adaptation to a different type of gas e the lower side the cooking hob is fitted with a gas connection plug with a EN ISO 10226 1 2 or EN ISO 228 1 Depending on the country specific connection regulations thread e Also supplied with the appliance is an adapter for liquid gas and a non metal gasket e When connecting the knee R should be held firmly to prevent it from rotating e For sealing of the connection joints use a non metal approved gaskets and approved sealants e The gaskets should only be used once The thickness of the flat non metal gaskets should not be deformed more than by 25 percent e To connect the appliance to the gas supply use a tested and certified flexible hose e The flexible connection hose should be able to move freely It should not come into contact with the movable parts of the kitchen furniture e g a drawer or the bottom of the cooking hob e If an electric oven is built into the kitchen element under the cooking hob it should be fitted with a cooling fan and the connection should be made using a pipe completely made of metal e g a stainless stee
Download Pdf Manuals
Related Search