Home

Mobotix MX-D25M-SEC-D38 surveillance camera

1. Sef 160 mm 10 Set 166 mm MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com 74 mm 64 140 D25M Camera Manual Installation L Use the fold out template included at the end of the printed manual valid for both 0 and 10 On Wall Sets Make sure that the drilling template is not scaled or adjusted to the paper size when printing the PDF file enlarged or reduced The maximum torque for all screws is 1 to 1 2 Nm Required Parts Please first check that all components supplied with the On Wall Set are present in the original packaging The following additional items are required for installation e Suitable materials for ceiling wall installation 4 screws incl screw anchors and washers e g from the original camera packaging e Screwdriver e Power drill for screw anchor holes needed for ceiling wall mounting e MOBOTIX drilling templates at the end of this manual e Scissors to cut out the template e Pen mark the drill holes e Materials and tools needed to connect the pre installed MOBOTIX network cable in the camera with the on site network cable MOBOTIX AG e Security Vision Systems Made in Germany www mobotix com sales mobotix com Mounting the Camera with the On Wall Set 65 140 2 3 2 Procedure 1 Attach washers Prior to installation stick a black foam rubber washer ar
2. 2 7 3 Mounting to a Wall or Building Corner Mark the four screw anchor holes on the corner of the building ensuring that the arrows on the mount point upwards Drill the holes with a 10 mm wall drill Pass the on site network cable through one of the large round holes at the back of the Corner and Pole Mount then through one of the 16 mm diameter holes on the front of the mount In order to properly protect the cabling you should let the cabling run from the inside of the building through the Corner and Pole Mount directly into the camera concealed cabling Note The cable length from the building corner should be at least 80 cm Place the included wall anchors in the drilled holes and screw the Corner and Pole Mount into place on the corner of the building using the Torx screws and washers Use the supplied drilling template fold out at the end of this manual to mark the exact positions for the drill holes Use the supplied screw anchors screws and washers to affix the Corner and Pole Mount to a building corner MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com Installing the Corner and Pole Mount 2 7 4 Mounting the Wall Mount to the Corner and Pole Mount e Feed the network cables through the appropriate hole at the back of the Outdoor Wall Mount The wall seal ing on the Wall Mount must be in place already e Usethe6x20 mm Allen screws 6 mm was
3. 3 5 4 Accessing Data on the MicroSD Card The following options facilitate access to the stored image and video sequences on a MicroSD card e n the web browser Play back the recorded event images without audio directly from the MicroSD card using the Playback view of the camera software e n MxEasy Play back the recorded video sequences with audio by accessing the MicroSD card in the MOBOTIX camera via the camera e In MxControlCenter Play back the recorded video sequences with audio by accessing the MicroSD card in the MOBOTIX camera via the camera or with a direct access to the MicroSD card via a card reader connected to the computer Access the card by setting the MicroSD card s drive volume as a directory in MxControlCenter If the recordings stored on the MicroSD card were encrypted you need to enter the password used for the encryption before you can access the data If this is the case both MxControlCenter and MxEasy will provide a dialog box for this purpose When using the MicroSD card from one MOBOTIX camera in another MOBOTIX camera you need to make sure that the time on the original camera is in sync with the new camera We recommend using automatic time synchronization via a time server Admin Menu Date and Time 3 5 5 Deactivating Card Recording Follow these steps to deactivate the memory on a MicroSD card Admin Menu Storage on External File Server Flash Device l Activate the None option
4. MxActivitySensor The D25M provides an activity controlled image analysis sensor as standard for detecting the movements of people and objects in a defined surveillance area full image or section The MxActivitySensor delivers reliable results particularly in outdoor area applications in contrast to video motion detection that continues to be available and that registers all image changes in defined video motion windows In the monitored area the camera distinguishes between the continuous movements of vehicles persons or objects that trigger an alarm and movements that do not set off an alarm such as shadows changing light conditions and trees swaying in the wind Low Power Consumption in Accordance with the PoE Standard IEEE 802 3af An D25M uses no more power than its predecessor typically 4 5 watts despite the new sensor technology Adjusting the PoE class via the camera software also enables the use of PoE switches that cannot be operated on all ports with PoE class 3 up to max 12 95 V MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com 19 140 20 140 D25M Camera Manual Product Overview 11 3 Decentralized Video System Usually cameras only supply images while processing and recording take place later on a central PC using video management software This centralized structure has too many limitations for high resolution video systems since it requires high network
5. mmm will have the IP address 10 8 0 11 C uan an Poder stomach Use the folioveng IP address IP addens 10 3 0 Subnet mask 2 0 0 0 MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com First Images and the Most Important Settings 101 140 Linux Unix Open a terminal as root user 2 Enter the following command ifconfig eth0 1 10 8 0 11 3 The computer is now also using the IP address 10 8 0 11 Mac OS X Open System Properties gt Network 2 Select Ethernet In the Configuration field select 9 m 77 Manual and enter a 10 x x x IP address leg ne 73 10 8 0 11 3 Click Apply on the bottom right hand side of the dialog to assign the computer the IP address 10 8 0 11 2 Set Up the Target Network Parameters of the Camera 1 Open a web browser on the computer and enter the default IP address of the MOBOTIX camera in the address bar of the browser e g 10 8 0 99 Pressing Enter displays the user interface of the MOBOTIX camera see also Section 3 2 2 First Images and the Most Important Settings in the Browser 2 Click the Admin Menu softbutton in the user interface of the MOBOTIX camera The Quick Installation starts automatically once the admins user has logged on Admin Menu Note The Quick Installation can also be executed at a later stage by opening Admin Menu Network Setup Quick Installation see also Section 5 2 Q
6. Pe citings ad Pe wher the ino ape Jhon wie or Or te 2 1 99w menus Nor image wing the Live page Manes anc Geta rage woevo ate o he 12 Masc anc Geta rage wie cate Ihe Live page Defaut mode Of Live Die F yOu select Active De COAT OG aid 890 De Ltd play evert mages or Pe ever Sage Browse page ON rete present Pe toster bon towng Gown Pow those Cipin ont pra mages MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com D25M Camera Manual Operating the Camera 40 200 You will find more information and details on the vPTZ in the Camera Software Manual Part 2 under Virtual PTZ in the MxEasy Manual under Activating the PTZ Features and in the MxControlCenter Manual under Using the vPTZ Features and PTZ Controls in the sidebar panel The latest versions of all manuals are available at www mobotix com Support gt Manuals 3 4 2 Full Image Recording It is possible to record a full image regardless of the live image stream that is being displayed This ensures that the recording always contains the full image of the lens used even though the operator may have used the vPTZ features to zoom into the image in order to examine a specific detail Stored Full Image Analysis in stored full image This means that you can use the vPTZ features in VGA resolution to pan tilt and zoom the liv
7. Made in Germany www mobotix com sales mobotix com 8 8 40 D25M Camera Manual Installation 2 9 Network and Power Connection 2 9 1 Notes on Cable Lengths and Power Supply e Power may only be supplied to the camera via its Ethernet connector A MOBOTIX Power Adapter or similar high quality PoE product is recommended to provide the power supply via the network cable one camera with the Network Power Adapter MX NPA PoE multiple cameras with quality PoE products conforming to IEEE 802 3af e The maximum length of the network cable for power supply over an Ethernet cable is 100 m e Make sure that you only use switches or routers that support the 10 100 Mbps Ethernet interface of the camera Check for LED activity on the corresponding port of the switch or router When deploying several cameras read the notes in Section 4 11 Operating Multiple Cameras in the Software Manual e tis highly recommend to use uninterruptible power supplies UPS to provide back Up power e f you are using IEEE 802 3af Power over Ethernet network components to supply power to MOBOTIX cameras make sure if possible that these components do not have a fan Since the power consumption of MOBOTIX cameras is very low compared to other products the reliability of the entire system is increased thus extending the life of these components Caution Connection of additional Appliances with a maximum total power consumption of 3 W may
8. Network parameters are automatically assigned No additional software is required You do not need to access the camera user interface Disadvantages The camera needs to be physically accessible as you need to press a key on the camera housing to boot it using DHCP Requires a running DHCP server on the network The IP address must be determined by the administrator MOBOTIX AG e Security Vision Systems Made in Germany www mobotix com sales mobotix com The ExtIO module is available from the MOBOTIX accessories program 100 140 D25M Camera Manual Operating the Camera Caution Netmask 255 0 0 0 3 2 First Images and the Most Important Settings Once the camera has been connected to the network you need to set up the camera s network interface accordingly This step involves setting up and checking the network parameters of the camera If your network is already using an IP address inthe 10 x x x range witha 255 0 0 0networkmask you do not need to change the camera s network parameters You can access the camera directly see Section 3 2 2 If your network or computer does not use an IP address in the 10 x x x range e g in the 192 or 172 ranges you should follow one ofthe following methods for changing the camera s network parameters e Manual Setup Section 3 2 1 e Automatic Setup using MxControlCenter or MxEasy Section 3 2 3 and Section 3 2 4 For the following examples we
9. 0 0025 BW 0 05 0 0025 BW Sensor sensitivity in lux at 1 60 s and 1s 0 25 0 013 Hardware Features IP protection class IP54 IP65 IP65 Temp Internal DVR MB 2 32 64 Internal DVR MicroSD up to 64 GB 4 GB included 4 GB included Microphone speaker Passive infrared sensor PIR E Integrated temperature sensor e Shock detector Power consumption in Watts typical 4 5 4 5 4 5 Variable PoE class 2 3 2 3 2 3 Image Formats Frame Rates and Image Storage Max resolution per sensor HD 1280x720 HD 1280x720 QXGA 2048x1536 Max frame rate MxPEG max resolution 30 fps 30 fps 20 fps CIF images with 4 GB MicroSD DVR 250 000 250 000 VGA images with 4 GB MicroSD DVR 125 000 125 000 MECA images with 4 GB MicroSD DVR 40 000 40 000 QXCA images with 4 GB MicroSD DVR 20 000 MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com Technical Specifications 2 140 1 2 3 Camera Variants Software Features Camera Model o General Features Digital zoom continuous with panning D25M Basic D25M IT D25M SEC Motion JPEG MxPEG H264 codecs e e e e e SIP video only e e SIP video only Programmable exposure ones Snapshot rec pre post alarm images 3 10 50 Terabyte ri
10. 2 7 Installing the Corner and Pole Mount 2 7 1 Mounting Instructions The 3 mm thick stainless steel Corner and Pole Mount is extremely robust and rust proof It is used exclusively in conjunction with the Wall Mount in situations where you want to mount a D25M IT Secure to a pole or wall corner The Wall Mount required for complete installation must be ordered separately The mounting pole should have a diameter of between 60 and 180 mm Attaching the camera to the corner of a wall not only makes sense from an aesthetic perspective but also allows you to monitor an area that is not specifically covered by the camera without incurring major building modification costs In such cases only the lens of the camera has to be repositioned By design the Corner and Pole Mount does not allow the use of a flush mounted socket Required Parts Please first check that all the components supplied with the Corner and Pole Mount Set are present in the original packaging The Following Additional Tools Are Required For Installation As A Pole Mount e Screwdriver e Materials and tools needed to connect the pre installed MOBOTIX network cable in the camera with the on site network cable MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com D25M Camera Manual Installation The Following Additional Tools Are Required For Installation Of The Corner Mount e Power drill for screw anchor holes
11. Add Video Sources nare IP address Path Type verson Status E x o ET 10 8 85 61 Q24M Secure MX 4 0 6 9 Bonjour Cancel Search 0 10 8 52 239 10 8 52 239 M24M Secure MX 4 0 4 18 Bonjour LER 10 3 30 151 D120 Sec MX V3 5 2 23 3 Bonjour Insert manualy Automated Search For Camera MOBOTIX Cameras MPEG do Recording path 2 video sources found 1 selected Add selected video sources Carcel List of video sources Camera preview Legend Video sources in this context not only refer to MOBOTIX cameras but also to third party IP cameras file server paths MxPEG clips and analog cameras connected via MxServer for example analog dome cameras These video sources are not found automatically and need to be added manually MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com 106 140 D25M Camera Manual Operating the Camera Cameras Are Found But Are Located in a Different Subnet The symbols in the first column and the legend in the dialog box indicate whether you can access a particular camera directly from the MxControlCenter which is the case for all cameras designated with OK Cameras designated with gt different subnet are located in a different subnet This usually applies to new cameras or cameras that have been reset to their factory settings MxControlCenter finds all MOBOTIX cameras even when the computer and the cameras are not l
12. Install and prepare the network connection Drill the holes Please use the enclosed screws and screw anchors whenever possible It is essential that you use the supplied drilling template to ensure the precise alignment of holes for either the mounting ring of the D25M IT Secure or the camera base of the D25M Basic fold out at the end of this manual Hollow out background surface for the cable and connector or insert the cable behind the suspended ceiling or cable duct Connect the pre installed network cable of the camera to the installation cable adapter not included in delivery Attach the camera to the ceiling or wall see sections below Aim and adjust the lens see Section 3 3 1 For safety reasons only use the pre installed MOBOTIX network cable that was included in the delivery Always ensure that the rubber plug of the network cable reliably protects the outer shell from moisture entering the camera All openings of the camera housing need to be properly sealed This is the only way to guarantee that the camera remains weatherproof Network Connection Without Pre Installed Cable The network cable is fed through the ceiling directly above the camera Make sure the cable is completely sealed by the rubber gasket on the housing do not bend the cable When preparing the installation ensure that at least 15 cm of cable length excluding the connector itself remains inside the camera housing similar to factory prei
13. Z D25M Camera Manual Security Vision Systems MOBOTIX 5MP Sensor lt Y H A e Fits In Watches Out The D25M Dome camera adapts perfectly to any task Exchangeable lenses various mounting and configuration options including Vandalism Set support unlimited possibilities On oo 60 192 EN V3 03 2014 Innovations Made in Germany The German company MOBOTIX AG is known as the leading pioneer in network camera technology and its decentralized concept has made high resolution video systems cost efficient www mobotix com MOBOTIX AG gt D 67722 Langmeil Tel 49 6302 9816 103 Fax 49 6302 9816 190 gt sales mobotix com 2 40 D25M Camera Manual Contents THE MOBOTIX INFORMATION CHANNELS Support on the MOBOTIX Website MOBOTIX www mobotix com other Support The MOBOTIX Video Tutorials www mobotix com other Support Tutorials Seminars on MOBOTIX Campus www mobotix com other Partners Seminars The MOBOTIX YouTube Channel www youtube com MOBOTIXAG MOBOTIX Seminars MOBOTIX offers inexpensive seminars that include workshops and practical exer cises For more information visit www mobotix com gt Seminars Copyright Information All rights reserved MOBOTIX the MX logo MxControlCenter MxEasy and MxPEG are trademarks of MOBOTIX AG registered in the European Union the U S A and other countries Microsoft
14. camera s default IP address in the browser address bar of the com puter see Section 3 2 2 The First Images And The Most Important Settings In The Browser Next click the Admin Menu button to open the camera s Quick Installation in the browser s user interface This is where you can configure the desired network parameters of the cam era Once you have completed the Quick Installation you can connect the camera with its new network parameters to the desired network Advantages The camera does not need to be physically accessible i e it can remain mounted to a pole for example No additional software is required The network parameters can be set flexibly through manual entry Disadvantages The computer or the network need to operate in the 10 x x x IP address range or need to be able to access such a network The setup does not work automatically You need to know the relevant network parameters MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com 98 140 D25M Camera Manual Operating the Camera MxControlCenter software free download from www mobotix com MxEasy free download from www mobotix com 3 1 2 Automatically Using MxControlCenter or MxEasy You can set up the camera s network parameters using the free of charge video manage ment software MxControlCenter or MxEasy see Section 3 2 3 and Section 3 2 4 You can also use
15. since the camera software will execute fewer write delete cycles on each storage cell The first deletion will begin once the SD card has been filled to capacity first full cycle MOBOTIX AG e Security Vision Systems Made in Germany www mobotix com sales mobotix com MicroSD Card Recording 123 140 File size single image 32 GB MicroSD Card Storage Requirements 6 fps CIF 6 fps VGA 1 fps MEGA 1 fps QXGA M JPEG M JPEG M JPEG M JPEG Storage required per second 90 kB 270 kB 75 kB 120 kB 240 kB Storage required per 24 hrs GB 23 5 GB 6 5 GB 10 4 GB 20 8 GB Time for one full cycle 4 days 1 3 days 4 8 days 3 days 1 5 days 4 GB MicroSD Card Storage Requirements 6 fps CIF 6 fos VGA 1 fps MEGA 1 fos QXGA M JPEG M JPEG MxPEG M JPEG M JPEG File size single image 15 kB 45 kB 120 kB 240 kB Storage required per second 90 kB 270 kB 75 kB 120 kB 240 kB Storage required per 24 hrs 7 8 GB 23 5 GB 6 5 GB 10 4 GB 20 8 GB Time for one full cycle 12 hours 4 hours 14 4 hours 9 2 hours 4 4 hours All specifications are based on calcu lated averages The MicroSD card s service life depends on production quality and frequency of use Set the type of recording event controlled or continuous recording frame rate resolution according to your specific requirements We recommend changing the pre
16. 2 Click on the Set button at the bottom of the dialog box and then on Close 3 Reboot the MOBOTIX camera Admin Menu gt Reboot Camera Once the camera has rebooted make sure that the symbol FR REC is no longer visible in the bottom right hand corner of the live image You can now safely remove the MicroSD card from the camera see Section 2 8 Replacing the MicroSD Card MOBOTIX AG e Security Vision Systems Made in Germany www mobotix com sales mobotix com MicroSD Card Recording 127 140 A MicroSD card may only be removed from the camera after you have deacti vated the recording to MicroSD card and rebooted the camera Failing to do so may lead to data loss Removing connected flash storage devices from the camera without properly deacti vating them may lead to data loss and or destroy certain areas ofthe storage device This is limited to 4 MB of lost data per incident due to MxFFS formatting 3 5 6 Using a MicroSD Card in a Different MOBOTIX Camera A MicroSD card containing recorded video data from a MOBOTIX camera can be inserted into any MicroSD card enabled MOBOTIX camera Once a MicroSD card recording has been activated requires a reboot the new MOBOTIX camera automatically synchro nizes with the card and resumes recording No data is lost in this process Make sure that you deactivate MicroSD card recording before removing the card and then reboot the MOBOTIX camera If the MicroS
17. 3 7 13 Online Help in the Browser For more information see the News and Functional Overview pages in the online help of the camera s browser interface Click on the icon to open the camera s online help Furthermore detailed information on the camera and its current configuration is displayed in the Camera Status dialog box Click on the P icon to open the relevant page MOBOTIX Q24 mx10 8 0 79 Live 6 Admin Menu X E Setup Menu II Arm amp Record E p Audio on OWN mikes gt 9969 FEN E MxPEG off uc Event LEDs Blink Play Sound Play Last Event MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com gt PE 136 140 D25M Camera Manual Operating the Camera 3 7 14 Declaration of Conformity The products of MOBOTIX AG are certified according to the applicable directives of the E U and other countries You can find the declarations of conformity of the products of MOBOTIX AG under www mobotix com Support gt MX Media Library gt Certificates gt Declarations of Conformity 3 7 15 Disposal Electrical and electronic products contain many reusable materials For this reason we would ask that you dispose of MOBOTIX products at the end of their service life in accor dance with all legal requirements and regulations or deposit these products at a munic ipal collection center MOBOTIX products may not be di
18. By default the MOBOTIX camera s event control is disabled Click on the Arm amp Record button to activate event control This will activate motion detection and recording Cameras with integrated flash memory MOBOTIX R models and models with an SD card will automatically use the flash memory to store image and video data recording target If desired you can set additional events and adjust the settings of the recording and storage parameters Setup Menu Event Settings Setup Menu Recording and Admin Menu Recording to External File Server Flash Device MOBOTIX AG e Security Vision Systems Made in Germany www mobotix com sales mobotix com Configuration in the Browser 3 140 e Setup actions messaging Upon detecting an event the MOBOTIX camera can trig ger alarms These alarms can be adjusted to your needs and you can assign them to a specific event playing back an alarm sound on the camera speaker showing the visual alarm in the camera live image sending an e mail or network message with the alarm image placing a phone call uploading an alarm image to an FTP server switching a signal output line of the camera for example for switching on the lights opening a door For the settings see Setup Menu Action Group Overview The actions to be per formed are defined and used in these action groups in the form of action profiles The different action profiles can also be defined in the followin
19. MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com 5 140 6 40 D25M Camera Manual Contents 3 7 9 Browser 134 3 7 10 Cleaning the Camera and Lens 134 3 7 11 Legal Notes 134 3 7 12 Safety Warnings 134 3 7 13 Online Help in the Browser 135 3 7 14 Declaration of Conformity 136 3 7 15 Disposal 136 3 7 16 Disclaimer 136 Manufacturer 139 Legal Notes Legal aspects of video and sound recording You must comply with all data protec tion regulations for video and sound monitoring when using MOBOTIX products Depending on national laws and the installation location of the D25M the recording of video and sound data may be subject to special documentation or it may be prohibited All users of MOBOTIX products are therefore required to familiarize them selves with all valid regulations and comply with these laws MOBOTIX AG is not liable for any illegal use of its products 5N MOBOTIX AG e Security Vision Systems Made in Germany www mobotix com sales mobotix com Contents 7 20 Safety Warnings Installation Instructions e This product must not be used in locations exposed to the dangers of explosion e Make sure to install this product as shown in Chapter 2 Installation of this manual e When installing this product make sure that you are only using genuine MOBOTIX parts and MOBOTIX connection cables e Make sure that you a
20. Storage Settings Value Recording REC Event Recording 9 Include audio amp Start Recording All E Set X Factory Y Restore X Close Explanation CS Recor wed by Com Sted ang amen sus iom camera Time Table Profile E Time Top I Signing mage 1 63 usg tme X 609 00110800 of me woo server certfcates of the wob server Activate Recording Status Symbol On wii graw a symoct n v6 image we IUS Ve Current arming and recording statu Term Terminate recording if an event is detected Use mis opt to roze sored wes 6 Pim Explanation Recording Mode Type of event and story recording Shot Recording stores single JPEG pictures Hecordug EIOS NCAM 1 06 for 0vory Evers ONG VXPLG 6 Rocorcing conti deg te peared videodata 1o stream fies using M Stove auto Cate in eroan Sio and configure microoh fi gt MOBOTIX Q24 mx10 8 0 113 Full Image Recording Attribute Value Image Size QXCA 2048x1836 i JPEG Quality 60 High Text Display Date amp time iE Date amp time e Explanation Image Size POCIO GOOLE Moga 1280x960 JPEG Quality Factory avtaut 60 Text Display Tno Due amp beo COLON wi Griy 0 90 0310 0nc tme Date and Time 06001 formar dale and pmo Set X Factory XY Restore Y Close Post event search in the full image If you are using Full Image Recording on D25M cameras y
21. e Screwdriver e Scissors to cut out the template e Pen to mark hole positions e Materials and tools needed to connect the pre installed MOBOTIX network cable in the camera with the on site network cable MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com Installing the Corner and Pole Mount 83 140 2 7 2 Mounting to a Pole Use the supplied stainless steel straps to affix the Corner and Pole Mount to a pole e Guide the supplied stainless steel straps through the openings in the Corner and Pole Mount as shown in doa m the diagram Make sure that you are using the slots of the mount that best fit for the thickness of the pole The stainless steel straps allow attaching the mount to poles 7 1 m with diameters between 60 and 180 mm N e Guide the on site network cable from behind through one of the large round holes of the Corner and Pole Mount In order to properly protect the cabling it is best to pass the cabling from the inside of the pole through the Corner and Pole Mount directly into the camera concealed cabling Note The cable length from the pole should be at least 80 cm e Tighten the stainless steel straps on the Pole Mount with a screwdriver If necessary the ends of the straps can be cut off MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com 84 1 D25M Camera Manual Installation
22. fire prevention and protection against lightning MOBOTIX cameras are protected against the effects of small electrical surges by a range of measures These measures however cannot prevent the camera from being damaged when stronger electrical surges occur Particular care should be taken when installing the camera outside to ensure proper protection against lightning as this also protects the building and the entire network infrastructure MOBOTIX recommends having MOBOTIX cameras installed only by certified specialists accustomed to installing network devices and having proper respect for the applicable regulations regarding lightning protection and fire prevention as well as the current tech nology for preventing damages from electrical surges Guidelines for Wiring e Data cable Make sure you only use double shielded CAT5 or higher cable S STP for Ethernet connections un M e Outdoors Installing the camera outdoors requires special precautions and measures regarding the cables as well as lightning and surge protection see below a e Wire lengths The cable segments must not exceed the maximum allowed cable lengths in order to ensure proper N data transfer see Section 2 9 e Avoiding induction When running data cables parallel to existing regular power lines or high voltage wires make sure you observe the minimum distances to the power cables Fire Prevention When installing the power lines to the
23. MxBus or USB interface The maximum length of the MxBus wiring 0 8 mm diameter wires is 50 m 55 yd If the MiniUSB connector is used the maximum cable length is 5 m 16 ft 1 4 17 ExtlO Expansion Module Order no MX ExtlO The device which is suitable both for on wall and in wall installations contains a powerful speaker microphone infrared motion sensor ambient temperature sensor two input and two output contacts and two illuminated keys It isideal for door communication elevators access control systems etc The ExtlO is suitable for use as direct con nection to the S15 via a MiniUSB cable max 5 m which can be ordered separately or as a network connection via the PoE switch 1 4 18 Mx2wire Media Converter Order no MX 2wirePlus Set PW The Mx2wire system allows an Ethernet network with PoE to be set up via two wire cables which saves users Otte a from having to lay several hundred meters of Ethernet 5 cable For example an existing two wire cable of an 4 Tn analog video camera can be reused to connect a high resolution and modern IP network camera Mx2wire is delivered in the standard wall outlet frame in different designs however it can also be used with the available on wall socket that is included RARITY PL teenth MOBOTIX AG e Security Vision Systems Made in Germany www mobotix com sales mobotix com Available Accessories 43 140 1 4
24. One D25M camera equipped with a 82 Wide Angle lens is usually all that is required to monitor either an entire room from a corner or the four lanes of a gas station The high degree of image detail not only reduces the number of required cameras but also minimizes system costs by reducing the wiring complexity emergency power requirements and number of recording devices required D25M cameras IT and Secure feature direct recording to integrated MicroSD cards or external USB drives As a result these cameras can be used in standalone operation with zero network load MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com D25M Overview 13 140 Universal Application from the Vacation Home to the Airport MOBOTIX D25M cameras are suitable for use in large scale facilities like airports given their unlimited scalability and high performance However they are equally suitable for use in small commercial or private buildings thanks to their integrated event storage alarm and telephony functions The Right Lens for Every Application You can change the lens in the D25M camera models on site whenever necessary Each lens is secured by a lock ring Each camera has a factory aligned and quality tested lens which makes on site camera focusing unnecessary in most cases The D25M cameras are available for delivery with a lens of your choosing or no lens at all The image area captured by
25. Procedure Mounting the Camera with the In Ceiling Set Mounting Instructions Procedure Installing the Vandalism Set Mounting Instructions Procedure Installing the Wall Mount Mounting Instructions Procedure Installing the Corner and Pole Mount Mounting Instructions Mounting to a Pole Mounting to a Wall or Building Corner Mounting the Wall Mount to the Corner and Pole Mount Replacing the MicroSD Card Removing a MicroSD Card Inserting a MicroSD Card Network and Power Connection Notes on Cable Lengths and Power Supply Connecting the D25M to the Network Using a Patch Cable Power Supply Using a Switch Power Supply When Connected Directly to a Computer Power Supply with Power Over Ethernet Products Connecting a USB Cable Connecting a Two Wire MxBus Cable 48 48 49 5 52 53 54 56 56 58 59 60 62 62 65 67 67 70 72 72 74 76 76 79 81 81 83 84 85 86 86 87 88 88 88 89 90 90 91 92 MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com Contents 2 9 8 Variable PoE 94 2 9 9 Camera Startup Sequence 95 3 Operating the Camera 96 3 1 Manual and Automatic Operation Overview 96 3 11 Manually Using a Computer in the 10 x x x IP Address Range 97 3 1 2 Automatically Using MxControlCenter or MxEasy 98 3 1 3 Automatically Using DHCP 99 3 2 First Images and the Most Important Settings 100 3 2 1 Manually Setting Up the Network Parameters
26. Since the three holes for the screws in the outer shell are factory sealed they must broken open for example using a 5 mm drill bit 6 Tighten the base of the camera using the supplied screws Depending on the installation site the screw openings should be sealed shut e g with silicon 7 Insert the internal part of the camera with the lens mount into the attached outer shell and secure it by turning the two blue clamps in a clockwise direction using the supplied hook wrench or a screwdriver This will pre vent the internal part of the camera from falling out before it has been tightened into place 8 Now secure the internal part of the camera by turning thetoothed ring in a clockwise direction until you can still turn the internal part of the camera without much force 9 Connect the network cable to the network connector of the camera 10 Proceed to Section 3 3 1 Aiming and Adjusting the Lens MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com 62 140 D25M Camera Manual Installation 2 3 Mounting the Camera with the On Wall Set rs 2 3 1 Mounting Instructions On Wall Sets available in 0 and 10 inclinations allow the D25M to be installed quickly and easily on the wall or ceiling of a room When using the set outdoors IP65 ensure that the screw holes on the rear of the camera housing are sealed with the included foam rubber washers It i
27. Systems Made in Germany www mobotix com sales mobotix com Available Accessories 3 Q 140 1 4 4 In Ceiling Set Order no MX OPT IC Also suitable for For simple installation in false ceiling mounting to drywall tiles Suitable for discreet surveillance Optionally available with a stainless steel ring 1 4 5 Outdoor Wall Mount Order no MX OPT WH Consists of Outdoor Wall Mount and mounting supplies Covers 145 flush mounted sockets Space for expansion modules battery UMTS WLAN etc Easily mounted to poles using Pole Mount Weatherproof IP65 1 4 6 Corner and Pole Mount Order no MX OPT MH Flange for Outdoor Wall Mount Can be mounted to wall corners or poles 3 mm stainless steel white Wall Mount may be ordered separately or as a set 1 4 7 Tinted Dome Order no MX D25M OPT DCS Suitable for especially bright environments e g under direct sunlight A tinted dome reduces the glare from sunlight by 50 compared with the standard dome 1 4 8 MiniUSB Cable to MiniUSB Straight Angled Order no MX CBL MU EN PG STR 05 2 5 straight angled Only cables with angled plugs can be The MOBOTIX MX 232 IO Box can be connected for the D25M directly to the D25M with this cable which is up to five meters long MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com 40 140 D25M Camera Manual Product Overview Only cables w
28. Windows and Windows Server are registered trademarks of Microsoft Corporation Apple the Apple logo Macintosh OS X iOS Bonjour the Bonjour logo the Bonjour icon iPod and iTunesare trademarks of Apple Inc registered in the U S A and other countries iPhone iPad iPad mini and iPod touch are Apple Inc trademarks Linuxis a trademark of Linus Torvalds All other marks and names mentioned herein are trademarks or registered trademarks ofthe respective owners Copyright 1999 2014 MOBOTIX AG Langmeil Germany Information subject to change without notice Download the latest version of this and other manuals as PDF files from www mobotix com gt Support gt Manuals MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com Contents CONTENTS 1 Product Overview 10 1 1 D25M Overview 10 1 1 1 General Product Characteristics 10 1 1 2 Advantages and New Features 18 113 Decentralized Video System 20 1 1 4 Green IP Video 22 12 Technical Specifications 24 1 2 Lens Options Hardware and Software Features 24 12 2 Camera Variants Lenses Hardware Image Formats 26 12 3 Camera Variants Software Features 2 12 4 Technical Data 28 13 Delivered Parts and Dimensions 30 1 3 1 D25M IT Secure 30 1 3 2 D25M Basic 34 14 Available Accessories 38 141 On Wall Set 38 1 4 2 10 On Wall Set 38 14 3 Vandalism Set 38 14 4 In Ceiling Set 39 1 4 5 Outdoor Wall Mount 39 1 4 6 Corner and Pole Mo
29. bandwidth and the PC processing power is insufficient when using several high resolution cameras Due to the large number of computers and servers required traditional centralized systems are therefore becoming less suitable and cost effective As part of the decentralized MOBOTIX concept every camera features a high speed processor and ifnecessary digital long term flash memory MicroSD card can be integrated to provide several days of recording time The com 44 puter or video control center is CMOS CPU MicroSD required only to view and control 5 megapixels Image analysis Recording the cameras not to evaluate and record video This means that you do not have to rely on expensive overloaded video management software as most of the important functions that require a large amount of processing power are integrated into the MOBOTIX cameras themselves MOBOTIX camera Integrated sensors enable MOBOTIX cameras such as the D25M to automatically detect when an event has occurred If necessary the cameras will respond immediately with an alarm sound and will establish a direct video and sound connection to a control room The D25M is equipped with a shock detector as standard for all IT and Secure models For example if the camera receives a blow to the housing it can simultaneously take a video of the offender trigger a sound alarm and notify the security company by a SIP call Due to the build quality and absence of moving parts M
30. be connected to devices with more than the MxBus connector and USB connector if power is supplied fo the camera using PoE class 3 If PoE Class 2 is used the power consumption of all the connected ax ambient tempera ture 50 C 122 F appliances should not exceed 1 W For information on changing the PoE class see Section 2 9 8 Variable PoE 2 9 2 Connecting the D25M to the Network Using a Patch Cable Using a patch cable and an MX Overvoltage Protection Box or MX NPA Box offers the following advantages e Quick installation deinstallation e No shortening of cable even when installing deinstalling several times e Hose proof dust proof connection in accordance with IP65 e Additional protection against overvoltages of up to 4 kV when using the MX Overvoltage Protection Box MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com Network and Power Connection 89 140 Connecting the Patch Cable to an MX Overvoltage Protection Box an MX NPA Box or a Standard Network Outlet To establish the network connection of the camera using an MX Overvoltage Protection Box or an MX NPA Box remove fon BON S the blue bayonet catch and the blue sealing plug from the 9 right hand side of the box Insert the MOBOTIX patch cable 6 m F into the box and fasten the cable using the blue bayonet catch NPA Box For additional information on how to install an Eo cone MX Overvol
31. camera make sure you always adhere to the country specific regulations e g VDE in Germany IEEE in the USA in effect on wiring and fire prevention at the site of the installation MOBOTIX AG e Security Vision Systems Made in Germany www mobotix com sales mobotix com Preparing the Installation 5 5 140 Lightning and Surge Protection In order to avoid damage to MOBOTIX cameras from overvoltages you should always 9 install the MX Overvoltage Protection Box This competitively priced and weatherproof network connector provides reliable protection against overvoltages of up to 4 kV the box Z Moon 3 is easily installed in the Outdoor Wall Mount for example see Section 1 4 13 MX Overvoltage 9 Protection Box E e More information is available at an institution such as the International Electrotechnical Commission IEC www iec ch or at a manufacturer of protection devices against light 0 ning and electrical surges such as Dehn www dehn de MOBOTX 3 Overvoltage Protection 4 G G MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com 5 6 40 D25M Camera Manual Installation 2 2 Mounting the Camera Without Accessories 2 2 1 Mounting Instructions As an allround camera the D25M is primarily designed for installation on walls or ceilings In general direct installation of the camera without any accessories is always possib
32. friendly user interface and camera image display convenient video search functions effective alarm handling automatic camera integra tion video storage on file servers as well as useful configuration and update wizards MxControlCenter Professional Video Management Several hundred came ras can be managed on Proven worldwide in the most demanding video applications thousands of times over standard computer Unlimited number of users and cameras No license fees Individual user interface adaptable to each individual user Simplest installation and complete use on any standard PC Convenient layout editor for integrating real building plans Integration of conventional network and analog cameras as well For Microsoft Windows Download free of charge from www mobotix com No license fees Free updates MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com 46 140 D25M Camera Manual Product Overview Suitable for up to 16 MOBOTIX cameras Download free of charge from www mobotix com No license fees Free updates 1 5 3 MxEasy MxEasy makes it simple to operate the most important functions of the camera thanks to its intuitive user interface and represents a new approach to viewing and controlling MOBOTIX cameras The clear design allows you to manage up to 16 cameras and the application can show up to four cameras at the same time All settings selected in Mx
33. in a Browser 100 3 2 2 First Images and the Most Important Settings in the Browser 102 3 2 3 First Images and Network Parameter Configuration in MxControlCenter 104 3 2 4 First Images and Network Parameter Configuration in MxEasy 109 3 2 5 Starting the Camera with the Factory IP Address 112 3 2 6 Starting the Camera with an Automatic IP Address DHCP 113 3 3 Adjusting Lens Focus and Correcting Lens Distortion 114 3 3 1 Aiming and Adjusting the Lens 114 3 3 2 Correcting Lens Distortion L25 Only 116 3 4 Virtual PTZ and Full Image Recording 118 3 4 1 Preparing the Virtual PTZ Function 118 3 4 2 Full Image Recording 120 3 5 MicroSD Card Recording 122 3 5 Introduction 122 3 5 2 Formatting the MicroSD Card 124 3 5 3 Activating MicroSD Card Recording 125 3 5 4 Accessing Data on the MicroSD Card 126 3 5 5 Deactivating Card Recording 126 3 5 6 Using a MicroSD Card in a Different MOBOTIX Camera 127 3 5 7 Limitations on Warranty When Using Flash Storage Media 127 3 6 Configuration in the Browser 128 3 6 Overview 128 3 6 2 General Browser Settings 130 3 7 Additional Notes 132 3 7 Weatherproofness 132 3 7 2 Password for the Administration Menu 132 3 7 3 Permanently Deactivating the Microphone 132 3 7 4 Starting the Camera with the Factory IP Address 132 3 7 5 Resetting the Camera to Factory Settings 133 3 7 6 Aclivating Event Control and Motion Detection 133 3 7 7 Deactivating Text and Logo Options 133 3 7 8 Deactivating the Camera Reboot 133
34. including their consumption of energy and resources Sustainable Without mechanical components MOBOTIX cameras are maintenance free and stay fully functional even after years and are thus more sustainable compared to other systems Forward Looking Even previous camera models can be easily updated and then offer new functionalities Remote updates via the internet and the fact that the cameras are maintenance free reduce trips by car and thereby the negative effect on the environment MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com D25M Overview Notes MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com 2 4 140 D25M Camera Manual Product Overview 12 Technical Specifications 1 2 1 Lens Options Hardware and Software Features MOBOTIX currently offers five standard lenses with M14 thread from the L25 Super Wide Angle lens with a 22 mm focal length through to the L135 Telephoto lens with a 135 mm focal length equivalent to 35 mm camera Since MOBOTIX cameras are backlight proof they do not require a mechanical auto iris making them extremely robust and maintenance free L25 Super Wide Angle with 82 image angle horizontal L38 Wide Angle with 55 image angle horizontal L5 Wide Angle with 40 image angle horizontal L76 Telephoto
35. processed in the camera itself and the high resolution images therefore do not have to be constantly transported for analysis 8 D o c MOBOTIX System MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com 21 140 22 140 D25M Camera Manual Product Overview MOBOTIX Green IP Video 1 1 4 Green IP Video The modern network based video security technology offers numerous advantages to use energy efficiently Due to the special product and system properties the decision to install MOBOTIX video systems is also a decision for Green IP Video low power consump tion and environmental friendly because of long life expectancy and minimal amount of materials involved Low Power Consumption MOBOTIX cameras are cost efficiently supplied via PoE This reduces the expenses for power and in addition saves copper and other important raw material as less power cabling is necessary Robust MOBOTIX IP65 cameras are highly robust and work without high power climate control and extra protective housing in a temperature range from 30 to 50 C 22 to 122 F Modern Integrated into the cameras are high power processors and flash storage thus making energy consuming servers and storage devices unnecessary And of course the disposal of waste later High Resolution A hemispheric MOBOTIX camera with two image sensors replaces up to eight standard cameras
36. security providers cannot achieve this with the required level of quality Good Color Images Even in Low Light The more light sensitive an image sensor is the better the image quality especially when the ambient light level is low such as at dusk and in heavy rainfall The D25M offers the best MOBOTIX image quality that is currently available thanks to the light sensitivity pro vided by the five megapixel color sensor that is four times higher than that of the previous three megapixel color sensor and the new MxLEO exposure control More Details When Zooming The maximum zoom factor of the D25M is 1 26 times higher than that of the 514 due to the use of five megapixel technology This means that the degree of detail provided by the camera has improved by 26 percent As a result an D25M can now be installed even further away than before from the objects and areas to be monitored In addition this relativizes the horizontal image angles of the new five megapixel sensors that are slightly smaller compared to the D24M Black amp White Image Sensor with 5 Megapixels You can now order the D25M with a five megapixel night sensor that can deliver black and white images with up to QXGA resolution This results in larger images than those delivered by the previous 1 3 megapixel sensor with a perceptibly higher degree of details MOBOTIX AG e Security Vision Systems Made in Germany www mobotix com sales mobotix com D25M Overview
37. the D25M varies depending on the selected lens With a Super Wide Angle lens L25 with 82 for example almost an entire room can be recorded from just one corner With an L160 Telephoto lens a D25M camera with a high resolution Ux UR o gas 5 megapixel sensor is capable of clearly recording a license plate number from a distance of 75 meters Or even the serial number of a 5 euro bill from a distance of two meters MOBOTIX AG Security Vision Systems Made in Germany www mobotix com salesemobotix com With a D25M equipped with an L25 lens the slightly distorted image can be cor rected by software 4 140 D25M Camera Manual Product Overview Virtual PTZ vPTZ No Motor Required The D25M can zoom in on detail as well These vPTZ functions are a standard feature in the integrated D25M camera software The image from the mono dome camera can be enlarged using e g the mouse wheel a joystick or a software controlled PTZ panel and you can move the view to any section ofthe image This provides the features of a mechanical PTZ camera without the disadvantages of maintenance and wear ET j 4 T Quick and easy naviga tion with a USB joystick L3 f Original D25M image b with L25 lens 82 V Es aN M P Y q This vPTZ functionality works differently depending on the camera operation platform web browser MxE
38. the camera in any way For this reason the product must not be installed within the reach of persons without the dome Power off before opening the camera Make sure the power supply is disconnected before opening the camera i e for installing or replacing sensor modules and SD cards Network security MOBOTIX products include all of the necessary configuration options for operation in Ethernet networks in compliance with data protection laws The operator is responsible for the data protection concept across the entire system The basic settings required to prevent misuse can be configured in the software and are password protected This prevents unauthorized parties from accessing these settings ppp gt rr p MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com 8 140 D25M Camera Manual FOREWORD Dear MOBOTIX customer Congratulations on your decision to purchase an extraordinarily powerful and compact network camera Made in Germany The D25M Dome is a complete decentralized system that has a high performance processor integrated software an array of sensors and a digital SD card video recorder for long term storage The weath erproof MiniUSB and MxBus interfaces ofthe camera allow attaching MOBOTIX interface boxes and standard devices such as 3G UMTS modems external storage devices etc The numerous easily interchangeable lens options of the D25M provi
39. will snap into place when the trapezoidal elements on the rear of the camera housing exactly match up with the corresponding openings on the Wall Mount MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com 80 40 D25M Camera Manual Installation 5 Mount the Wall Mount without camera Stick the black wall sealing to the back of the Wall Mount remove the adhesive foil first the surface must be clean and free of grease Pass the network cable through the large square opening and into the Wall Mount Use the included screws to install the Wall Mount without the camera at the intended position Pass the network cable through the large square opening on back side of the Wall Mount for connection with the camera patch cable using a i standard connector Excess cable can be stored easily K within the Wall Mount a p KK 6 Connect the cable Prepare the on site network cable A 7 Install the bottom plate with the camera in the Wall Mount Connect the camera patch cable to the network cable Then mount the bottom plate with the camera in the slots from below and fix it in place on the Wall Mount using the 4 Allen screws Allen wrench included 8 Proceedto Section 3 3 1 Aiming and Adjusting the Lens MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com Installing the Corner and Pole Mount 8 140
40. will use a camera with the factory address 10 8 0 99 Replace this IP address with the IP address of your camera You will find the IP address of your camera on a small sticker on the camera Make sure that the IP addresses used in the following examples are not already being used by other devices in the network Hint Pressing the R key on the camera prompts the camera to announce its current IP address over a speaker 3 2 1 Manually Setting Up the Network Parameters in a Browser In order to manually set up the network parameters of the MOBOTIX camera you need a computer that is using a 10 x x x IP address The computer s network parameters usually have to be changed for this purpose 1 Change the Network Parameters of Your Computer Windows 2000 XP and Vista Local Area Connection Properties 1 Open Start gt Settings gt Control Panel gt Network sees Connections Clicking Properties opens the dialog E EE shown This connection uses the following Remi v Chert for Microsoft Networks v File and Printer Sharing for Microsoft Networks v QoS Packet Scheduler v Irtemet P 2 Double click Internet Protocol TCP IP On the General tab activate the Use the following IPaddress C NN option Enter an IP address in the 10 x x x range in this field e g 10 8 0 11 You can get IP settings assigned automatically your nelwork supports 3 Once all dialogs have been closed the computer
41. with 27 image angle horizontal L160 Telephoto with 13 image angle horizontal The L25 Super Wide Angle 82 lens has very little distortion and delivers good image quality even when using the maximum digital zoom If a camera with this lens has been mounted in the corner of a room the complete room is visible on the image Original image from a D25M with 82 lens L25 MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com Technical Specifications 25 140 Original image 35 mm equivalent focal 25 mm 38 mm 5 mm 76 mm 160 mm length 0 98 in 1 50 in 2 01 in 2 99 in 6 30 in Actual focal length 0 Bul G a pu ov du 0 16 in 0 24 in 0 31 in 0 47 in 0 98 in Aperture 2 0 2 0 2 0 2 0 2 5 Horizontal image angle 82 55 40 27 13 Vertical image angle 61 41 30 20 10 Distance 1 m 1 09 yd Image width 17 1 0 OF 0 5 0 2 Image height 1 2 0 7 0 5 0 4 0 2 Distance 5 m 5 47 yd Image width 8 7 5 2 3 6 24 1 1 Image height 5 9 3 7 2 7 1 8 0 9 Distance 10 m 10 94 yd m m m m m Image width 17 4 10 3 7 2 4 9 2 3 Image height 11 9 7 5 5 4 3 6 1 7 Distance 20 m 21 87 yd Image width 34 7 20 6 14 5 9 7 4 6 Image height 23 7 14 9 10 8 7 2 3 4 Distance 50 m 54 68 yd Image width 86 8 51 5 36 2 24 3 11 4 Image height 59 3 37 3 27 0
42. within the camera housing so that they do not obstruct the main board when adjusting the camera image e Remove the camera dome Take the delivered plastic foil or a cotton cloth insert the dome into its seat and turn it in clockwise direction gt Attach the outer shell Place the outer shell onto the camera and tighten all four Allen screws using the supplied Allen wrench Make sure that the rubber seal is seated properly MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com 94 140 D25M Camera Manual Installation Variable PoE Multiple cameras can be operated simultaneously from the same switch 2 9 8 Variable PoE The power consumption of the camera depends on the functions in use as well as any peripheral devices connected see table PoE classes 1 2 or 3 may be selected in the browser based user interface in order to optimally adjust the camera to your system design PoE switch in use emergency power concept etc PoE Power Level Classes IEEE 802 3af Standard Max power consumption 0 44 W 3 84 W Camera operating mode and peripheral devices LowPower mode no peripheral devices available soon 2 3 84 W 6 49 W Normal mode max 1 W for MxBus peripheral devices 3 6 49 W 12 95 W FullPower mode max 2 5 W for MxBus peripheral devices for example MX GPS Box and MX 232 IO Box to MxBus max 4 W for peripheral devices to M
43. 0 013 lux at 1 s Black and white sensor 0 05 lux at 1 60 s 0 0025 lux at Vis Image sensor 1 2 5 CMOS 5 megapixels progressive scan Max image resolution Color Black and White 2048x1536 QXGA Image formats Selectable image formats for example 2048x1536 MEGA 1920x1080 full HD 1280x960 MEGA 1280x720 HD 1024x768 800x600 768x576 D1 PAL 704x576 TV PAL 640x480 384x288 320x240 160x120 Max frame rate M JPEG live recording VGA 30 fps MEGA 10 fps QXGA 4 fps Max frame rate MxPEG live and recording incl sound VGA 30 fps MEGA 30 fps QXGA 20 fps Image compression MxPEG M JPEG JPEG H 264 SIP video only Internal DVR MicroSD slot incl 4 GB max 64 GB External video ring buffer Directly on NAS and computer server without additional recording software Software included MxEasy video management software MxControlCenter control center software MOBOTIX App for iOS devices iOS 5 0 and higher Image processing Backlight compensation automatic white balance image distortion correction panorama correction Video Motion detection MxActivitySensor Virtual PTZ Digital pan tilt zoom continuous 8X zoom Alarm events Video Motion detection MxActivitySensor external signal temperature sensor PIR microphone shock detector notification over e mail FTP IP telephony VoIP SIP visual acoustic alarm pre and post alarm i
44. 18 0 8 6 The specified focal lengths of the MOBOTIX lenses do not reflect the actual focal length of the lenses but the focal length Lxx mm converted to 35 mm camera format For example the MOBOTIX L25 Super Wide Angle lens has an actual focal length of 4 mm This would be the equivalent of 25 mm on a 35 mm camera It is therefore referred to as an L25 Since the image sensors in digital cameras have different sizes converting the focal lengths to 35 mm camera as a known format allows the image formats and the fields of vision of the different lenses to be calculated and compared more easily Another benefit is that you can easily set a 35 mm camera analog or digital to the same focal length as the MOBOTIX lens Lxx to obtain the same field of vision This approach greatly facilitates lens selection MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com 2 6 140 D25M Camera Manual Product Overview 1 2 2 Camera Variants Lenses Hardware Image Formats Sp ve D25M Basic D25M IT D25M SEC Camera Model Lenses Sensors Hemispheric 12 mm Super Wide Angle 25 mm L25 L25 L25 Wide Angle 38 mm L38 L38 Wide Angle 51 mm L5 L5 Tele 76 mm L76 L76 Tele 160 mm L160 L160 CSVario 24 54 mm Image sensor with individual exposure zones Color Color BW Color BW 0 25 0 013 Color 0 25 0 013 Color 0 05
45. 19 Other Accessories Since the range of accessories for the MOBOTIX system keeps growing you should visit the MOBOTIX website www mobotix comin the Products gt Accessories section to see the entire list of available accessories THE MOBOTIX INFORMATION CHANNELS Support on the MOBOTIX Website MOBOTIX www mobotix com other Support A The MOBOTIX Video Tutorials www mobotix com other Support Tutorials Lp Seminars on MOBOTIX Campus www mobotix com other Partners Seminars The MOBOTIX YouTube Channel You Tube www youtube com MOBOTIXAG MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com 44 140 D25M Camera Manual Product Overview Download free of charge from www mobotix com No license fees Free updates 15 MOBOTIX Software 1 5 1 Integrated Camera Software Firmware MOBOTIX cameras and connected MxBus modules operate with built in firmware whose functions are accessed by the MOBOTIX MxControlCenter MxEasy remote stations and MOBOTIX App The D25M models therefore also feature a variety of functions that are integrated in the firmware from motion detection and long term storage right through to alarm notification via video IP telephony The virtual PTZ functions allow you to continuously zoom into or out of a MOBOTIX camera image using either the mouse wheel or a joystick When recording image or video sequences you can choose to store either the section o
46. 4 Stainless steel Torx screws 4 5x60 mm 2 13 Torx wrench TX20 2 14 4 Allen screws M4x16 mm 2 15 4 Stainless steel washers 4 3 mm MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com Delivered Parts and Dimensions 3 5 140 Camera Housing and Connector The MOBOTIX D25M Basic consists of the camera housing with the motherboard the lens and the dome Connections e Network Ethernet network incl PoE supply Dome Lens unit Network connection see Section 1 3 1 R key L key LEDs MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com 3 6 40 D25M Camera Manual Product Overview Dimensions Camera module can be freely rotated and tilted By rotating the camera module on both axes you can aim the lens at the precise area you want to record 85 mm 129 mm MOBOTIX AG e Security Vision Systems Made in Germany www mobotix com sales mobotix com Delivered Parts and Dimensions 37 140 Drilling Template EET A ANSA Use the folded drilling template at the end of the manual Make sure that the drilling template is not scaled or adjusted to the paper size when printing the PDF file enlarged or reduced When printing this page make sure that you are printing at 10096 scaling to obtain an unscaled printout ofthe drilling template
47. D card s contents are encrypted you need to enter the same password in the new camera in the Admin Menu gt Storage on External File Server Flash Device dialog box Otherwise the camera cannot access the MicroSD card 3 5 7 Limitations on Warranty When Using Flash Storage Media MOBOTIX will not assume any responsibility for flash storage devices for example MicroSD cards or connected USB storage devices delivered with or integrated into MOBOTIX cam eras The same applies to damage to flash storage devices or damage resulting from the use of devices that are not supplied by MOBOTIX MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com 128 140 D25M Camera Manual Operating the Camera 3 6 Configuration in the Browser eoe ce Q o Eb hup 10 8 0 99 gt x IIl Googie P x 16 tps T Display Mode 3 6 1 Overview A MOBOTIX camera can be completely configured using a JavaScript enabled browser on all common operating systems such as Windows Linux Apple etc The camera provides a HTML based user interface for this purpose The camera executes the changes you make to the camera configuration via HTTP commands using programs and scripts of the embedded software The settings are stored in the camera s flash memory This section contains an overview of the basic browser settings of the MOBOTIX camera as well as further configuration option
48. Easy for example virtual camera position zoom brightness volume microphone sensitivity image storage signal outputs can be used immediately and are stored instantly in the configuration of the corresponding camera The calendar functions integrated in the Alarm Planner provide an innovative tool for the scheduled settings of one or more cameras This tool not only controls video and sound recording based on certain time and date information but also allows features like video motion detection image brightness and the microphone to be activated deactivated based on a date and time schedule MxEasy Simple Operation of the Most Important Camera Functions e Cameras can be installed without any knowledge of networks e Supports up to 16 MOBOTIX cameras e Time or event controlled recording Time controlled motion detection image brightness and microphone For Microsoft Windows and Mac OS X 5 us Jossa F MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com MOBOTIX Software 47 140 1 5 4 MOBOTIX App Premium solution There for you whenever and wherever you need it the MOBOTIX App serves as the perfect remote mobile station that uses intelligent detailed solutions to increase security and convenience for users on a daily basis The controls are optimized for use with touchscreen devices and feature three main views Live Player Events self explanatory symbols large softwar
49. IX camera now starts for matting the card It takes 5 to 12 min utes to format an 8 GB MicroSD card if the Secure deletion Slow option is disabled If Secure deletion Slow is enabled this may take anywhere between 3 and 14 hours Really proceed with formatting and erasing device SD Flash Card ae Once the formatting has been completed you can activate the MicroSD card for recording see next section Make sure that you always wait until the formatting process has been completed before accessing the camera again If the Secure deletion Slow option is disabled this usually takes just a few minutes You can only access the MicroSD card once MxFFS formatting has been completed Formatting with the Secure deletion Slow option enabled takes several hours You can also use suitable applications on Windows Linux UNIX and Mac OS X systems to repartition and safely erase the MicroSD card MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com MicroSD Card Recording 125 140 3 5 3 Activating MicroSD Card Recording Follow these steps to activate the recording to a MicroSD card that has already been MxFFS formatted Admin Menu Storage on External File Server Flash Device 1 2 3 4 5 Make sure that there is a MicroSD card in the card slot of the MOBOTIX camera Make sure that the MicroSD card is formatted in MxFFS format Activate the SD Flash Car
50. MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com Find the drilling templates scale 1 1 at the end of the manual as a fold out 38 140 D25M Camera Manual Product Overview 1 Available Accessories 1 4 1 On Wall Set Order no MX OPT AP Consists of On Wall Mount and mount ing supplies Conforms to U S instal lation standards Reliably protects the cabling and allows additional modules to be integrated within the On Wall Mount patch installation cable con nector IO extensions WLAN battery 1 4 2 10 On Wall Set Order no MX OPT AP TODEG Consists of On Wall Mount and mount ing supplies for inclined installation 10 of a camera Conforms to U S instal lation standards Reliably protects the cabling and allows additional modules to be integrated within the On Wall Mount patch installation cable con nector IO extensions WiFi battery 1 4 3 Vandalism Set Order no MX D25M Vandal Consists of a stainless steel ring secu rity screws and reinforced dome 3 mm polycarbonate Ideally suited for surveil lance at critical locations In order for the camera to blend in bet ter with its environment the Vandalism Set is available in five different finishes matt stainless steel polished white powder coated black powder coated silver gray powder coated 165 x 37mm ta pm MOBOTIX AG Security Vision
51. MX OPT GPS1 EXT The MX GPS Box primarily serves as a high precision time source for systems without an Internet connec tion In addition it can provide triggering based on GPS events reaching or moving away from a specified posi tion exceeding or not reaching a specified speed This interface box can be attached to all MOBOTIX cameras with an MxBus interface MOBOTIX Overvoltage Protection G 8 Mie The MX GPS Box is equipped with the same compact housing as the other interface boxes protection class IP65 30 to 60 C 22 to 140 F This interface box should not be installed inside of other wall mounts but on the exterior of the building with a large section of open sky above it This ensures the best possible reception from GPS satellites MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com 42 140 D25M Camera Manual Product Overview and thereby the highest possible accuracy of the received GPS data The maximum length of the MxBus wiring 0 8 mm diameter wires is 50 m 55 yd 1 4 16 MX 232 IO Box Order no MX OPT RS1 EXT This box provides the signal inputs and outputs as well as the RS232 serial interface It replaces the connections that MZ Or were handled on the older camera models via a D Sub 15 HD connector The MX 232 IO Box protection class IP65 30 to 60 6 22 to 140 F can be attached to all MOBOTIX cameras with an
52. MxEasy will kccp thc configuration of thc camcra s You will configure MxEasy during the following steps Quick Start MxEasy will keep the configuration of the camera c MxEasy will be set to default settings Here you can jump directly to the main window of MxEasy with the current live camera image by activating the option Quick Start However some required detailed configura tions may have to be made at a later time for example password protection available bandwidth For this reason we recommend activating the option Complete integration and complete the remaining dialog boxes of the MxEasy Assistant until the main window appears AN Malley Led 83 Duae 556 Ansictt Kamere VO Gis Emas Fenster Hilfe After you are done with the MxEasy Assistant the application s main window appears and displays the first camera Main window with image of a D25M For more information see the MxEasy User Manual which can be down loaded as a PDF file from the MOBOTIX website www mobotix com Support Manuals MOBOTIX AG Security Vision Systems Made in Germany www mobotix com salesemobotix com 112 140 D25M Camera Manual Operating the Camera Passwords and cam era settings will not be changed Make sure you store the default network configuration to the permanent flash memory 3 2 5 Starting the Camera with the Factory IP Address If your network has a DHCP server you can start
53. OBOTIX cameras are extremely tough This typically allows them to stay fully operational especially when they are subject to strong vibrations All MOBOTIX cameras are backlight proof and are not adversely affected by the glare from direct sunlight They deliver meaningful detailed images at all times as the camera software supports easy programming of independent exposure windows making them ideal for rooms with large glass fronts In the event of an alarm MOBOTIX D25M camerascan also record lip synchronous audio The cameras therefore play an important role in analyzing and clarifying a situation Thanks to an integrated speaker and microphone each individual camera can also be used for bidirectional communication two way video communication so you can easily use the MOBOTIX App with your iPhone or iPad on the road MOBOTIX AG e Security Vision Systems Made in Germany www mobotix com sales mobotix com D25M Overview The decentralized MOBOTIX video solutions are superior to traditional systems in all major aspects They are also considerably cheaper to operate since they require e Fewer cameras due to the more accurate detail of panorama images with mega pixel technology e Fewer recording devices because in the decentralized system ten times the standard number of cameras can be used to record high resolution HDTV video with sound on one computer server simultaneously e Lower network bandwidth because everything is
54. Registration Office Kaiserslautern Local Court Registration Number HRB 3724 Tax Office Worms Kirchheimbolanden Germany Tax Code 44 676 0700 4 VAT ID DE202203501 You can find the latest version of this and other documents e g declarations of conformity at www mobotix com in the Support section CE Technical specifications subject to change without notice MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com Z D25M Camera Manual Security Vision Systems MOBOTIX 5MP Sensor lt Y H A e Fits In Watches Out The D25M Dome camera adapts perfectly to any task Exchangeable lenses various mounting and configuration options including Vandalism Set support unlimited possibilities On oo 60 192 EN V3 03 2014 Innovations Made in Germany The German company MOBOTIX AG is known as the leading pioneer in network camera technology and its decentralized concept has made high resolution video systems cost efficient www mobotix com MOBOTIX AG gt D 67722 Langmeil Tel 49 6302 9816 103 Fax 49 6302 9816 190 gt sales mobotix com
55. amera dome Take the delivered plastic foil or a cotton cloth and remove the dome by turning it in counter clockwise direction e Remove the MicroSD card Gently push the MicroSD card into the card slot of the camera The card is released from the slot and can be removed from the camera MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com Replacing the MicroSD Card 87 140 2 8 2 Inserting a MicroSD Card Push push operation insert the MicroSD card l Insert the MicroSD card Push the MicroSD card into the and push it in gently card slot as shown until an audible and perceptible click ECT indicates it is in place e Remove the camera dome Take the delivered plastic foil or a cotton cloth insert the dome into its seat and turn it in clockwise direction e Attach the outer shell Place the outer shell onto the camera and tighten all four Allen screws using the supplied Allen wrench Make sure that the rubber seal is seated properly St e Activate recording If you have inserted a MicroSD card that has already been MxFFS formatted you can activate recording under Admin Menu Storage on External File Server Flash Device Once the camera has been rebooted it automatically activates recording e f you are using a new MicroSD card it must first be formatted as described in Section 3 5 MicroSD Card Recording MOBOTIX AG Security Vision Systems
56. an a quarter million event images in VGA format 640 x 480 For security reasons the camera can even encrypt the stored data Power failures are not an issue as the video and image sequences remain safely stored on the MicroSD card Access to stored video sequences is possible at any time from the camera user interface in the browser MxControlCenter or MxEasy If you would like to archive sequences you can store all of the data or only certain parts to a computer or a USB hard disk MxActivitySensor Video Motion Analysis Secure Detection Avoiding False Alarms Regardless if there are large objects in the foreground or small objects in the background MxActivitySensor will only trigger video recording and alarm messaging if something important is happening Interference such as trees shaking in the wind moving shadows and clouds and snow falling will no longer lead to false alarms Since all of this is filtered automatically all that remains is to set the direction of movement of objects that should trigger alarms Robust and Maintenance Free Thanks to their low power consumption of approximately 3 watts and the total absence of mechanical moving parts the D25M models feature the highest operating temperature range from 30 to 50 C 22 to 122 F and are completely dust proof and resistant to water jets D25M IT Secure IP65 D25M Basic IP54 Since the cameras neither fog up nor require heating power can be supplied all year roun
57. and night sensors While the image sensor shows its full strength when zooming the live image the maximum image size per sensor has the more user friendly QXGA format Low Light Conditions No Problem The maximum resolution of the color and black amp white image sensors is 5 megapixels The higher light sensitivity of the new color image sensors now allow using MOBOTIX color cameras around the clock even when the illumination is low MxLEO Exposure Optimization and Reduced Image Noise MxLEO the MOBOTIX Lowlight Exposure Optimization is an innovative technology that provides an entirely new experience in digital image optimization in all cameras running firmware 4 1 9 and higher On the one hand the improved light sensitivity of the MOBOTIX 5MP sensors drastically reduces exposure times MxLEO the exposure and image optimi zation program especially developed for these conditions on the other hand generates perceptibly better and more detailed images especially under low light conditions below 25 Lux Such conditions are typical at a parking lot at night that is illuminated by regular lights approx 10 to 25 Lux Or in a building after hours in which the emergency lights are burning approx 5 Lux This significantly reduces motion blur that is typical of longer exposure times with little light and thus provides much more image detail faces license plates etc for proper identification High Resolution Sees More and Costs Less
58. ased video security technology that increases operating efficiency and yields a high degree of every day usefulness Extraordinary Picture Quality Image quality is the one key criterion of a security camera Due to their internal video analysis and data storage capabilities the decentralized MOBOTIX systems are indepen dent of the available network bandwidth As a result the system provides for efficiently storing and managing the video streams of a virtually unlimited number of cameras with the highest resolution at a reasonable cost 5 Megapixel Image Sensors 5MP MOBOTIX cameras possess high resolution image sensors with 5 megapixel resolu tion and excellent light sensitivity which translates into more details when zooming and more clear cut advantages for every user By using the 5MP technology in their color and black amp white image sensors MOBOTIX cameras deliver convincing image quality and details even in bad weather and under lowlight conditions Another important plus thanks to its internal pre processing of the image data the camera can generate video streams with up to 30 frames per second MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com MOBOTIX ExtIO functional exten sion for D25M 12 140 D25M Camera Manual Product Overview QXGA Image Format 2 5 Times More Detail Than Full HD The 5MP sensor has a resolution of 2592 x 1944 pixels on both day
59. asy MxControlCenter Virtual zoom pan and tilt using MxEasy and MxControlCenter is very simple thanks to special software tools and the use of an optional joystick However a joystick may also be used even with pure browser based operation from Internet Explorer together with an ActiveX plug in MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com D25M Overview 15 140 Simultaneous Zoomed Live Image and Full Image Recording All conventional motorized PTZ cameras only store the image that is currently viewed as the live image live image recording This has one serious disadvantage as the recording can only show what has happened in the visible portion of the image the rest is lost and cannot be examined later on For this reason MOBOTIX has added the new full image recording feature to the D25M This will not store the currently viewed image that reflects the pan tilt position and the zoom setting chosen by the user but the full sensor image without vPTZ settings When examining the recorded images at a later point in time the vPTZ features again come into play as they allow the visible image to be zoomed and use the pan tilt features to examine every corner of the recorded full image Example The people marked by the red circle in the middle area of the image would not have been recorded by a regular PTZ camera the full image recording of the D25M allows you to determine
60. cable The EU ver sion of the NPA PoE Set is supplied as standard with a European adapter while the INT version includes four adapters EU USA UK AUS MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com Available Accessories 41 140 1 4 13 MX Overvoltage Protection Box Order no MX Overvoltage Protection Box RJ45 Order no MX Overvoltage Protection Box LSA Weatherproof network connector protection class IP65 30 to 60 6 22 to 140 F with surge protection of up to 4 kV for MOBOTIX IP cameras ideal for replacing the MX Patch Box At the same time the MX Overvoltage Protection Box provides a weatherproof connection of a camera s patch cable to a network patch cable RJ45 variant or a network installation cable LSA variant 1 4 14 MX NPA Box Order no MX OPT NPAT EXT The MX NPA Box is a weatherproof PoE injector con forming to the IEEE 802 3af standard and is designed to connect external voltage sources 12 to 57 V DC to a MOBOTIX camera The MX NPA Box is equipped with the Patch Box s weath erproof and extremely compact exterior housing protec tion class IP65 30 to 60 C 22 to 140 F which means it can also be installed in the space of the Outdoor Wall Mount Interfaces of the MX NPA Box Camera via patch cable Ethernet via LSA and external power supply via terminal connector 12 to 57 V DC possible 1 4 15 MX GPS Box Order no
61. can reset spe cific parts of the configuration If the dotted rect angle in the live image is visible the camera is armed Text and logos can be also deactivated or individually configured 134 140 D25M Camera Manual Operating the Camera 3 7 9 Browser Current Internet browsers Internet Explorer Mozilla Firefox Safari Google Chrome Opera etc with enabled JavaScript can display the camera s live images with their standard settings 3 7 10 Cleaning the Camera and Lens Ifthe lens becomes dirty during the installation process clean the lens using a lint free cotton cloth Make sure that the lens is still in focus after cleaning and adjust its focus if required Cleaning the Dome e norderto protect the dome from being scratched and from getting dirty only handle the dome using a soft cotton cloth or the protective plastic of the camera s shipping box e You should clean the dome at regular intervals Always use a soft lint free cotton cloth for this purpose e f the dirt is more persistent add a mild alcohol free detergent without abrasive particles e Make sure you instruct cleaning personnel on how to clean the camera 3 7 11 Legal Notes Legal aspects of video and sound recording You must comply with all data protection regulations for video and sound monitoring when using MOBOTIX products Depending on national laws and the installation location of the D25M the recording of video and sou
62. com sales mobotix com Installing the Vandalism Set Available Variants of the MOBOTIX D25M Vandalism Outer Shell First make sure that all parts have been properly delivered Polished stainless steel Matt stainless steel Silver gray powder coated stainless steel White powder coated stainless steel re Black powder coated f stainless steel The Following Additional Tools Are Required for Installation e Allen wrench for removing the standard outer shell included in the D25M packaging e Screwdriver with bit receptacle for the two hole driver bit MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com 764 140 D25M Camera Manual Installation 2 5 2 Procedure e Remove the camera outer shell Remove all four Allen screws using the supplied Allen wrench and lift off the outer shell e Remove the standard dome Unscrew the dome from the housing counter clockwise Package and store the standard dome for possible use at a later time e Aim and adjust the lens When mounting the camera for the first time please proceed to Section 3 3 1 Aiming and Adjusting the Lens e Mount the reinforced dome of the Vandalism Set Tighten it in a clockwise direction using a soft cotton cloth If necessary clean the dome with a cotton cloth before installing it MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com Insta
63. d a robust 1 5 mm thick polycarbonate dome An extensive range of accessories is also available for installing the camera in an application optimized manner for supplying power or expanding the functions ofthe camera Furthermore MOBOTIX customers can take advantage of MxEasy or the professional control center software MxControlCenter free of charge and with an unlimited user and camera license If required a D25M camera can even be upgraded to function as a powerful intercom system by adding the MOBOTIX ExtlO module Robust and Elegant The D25M is available in the Secure IT or Basic models depending on the software features Five high performance lenses are currently available for the D25M in the compact M14 housing Due to their low power consumption of only 3 watts D25M cameras can oper ate in an extremely wide temperature range 30 to 50 C 22 to 122 F Since MOBOTIX cameras neither fog up nor require heating power can be supplied via the network cabling using standard PoE products The D25M IT and Secure models are completely dust proof and resistant to water jets IP65 D25M Basic IP54 The D25M Wall Mount makes the camera ideally suited for outdoor use and for installation over surface mounted sockets so that the cabling remains thoroughly concealed Complete HiRes Video Solutions by MOBOTIX As opposed to conventional solutions MOBOTIX cameras with their decen tralized approach offer so much more state of the art network b
64. d option Click on Set and then Close to store the configuration Reboot the MOBOTIX camera Admin Menu gt Reboot Camera Once the camera has rebooted make sure that the camera displays the FR REC symbols in its live image If this is the case the camera uses the MicroSD card as recording target If not you must activate the recording see below Activating the Recording Ifthe FR REC symbols are not visible in the live image after rebooting you need to activate the recording using one of the following methods In the web browser Automatic activation by clicking on the Arm amp Record softbutton Confirm this in the Easy Dialog by clicking on the Yes button In the web browser Manual activation via the Quick Control Recording Recording on or in Setup Menu Recording MxEasy It is possible to activate the recording based on the time or date using the Alarm Planner of MxEasy see MxEasy User Manual Encryption and Authentication All video data stored on the MicroSD card is encrypted to ensure security at all times The password for this is defined during the card s formatting procedure and needs to be entered for authentication whenever the recordings are accessed see next section MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com Activate recording Admin Menu Storage on External File Server Flash Device 126 140 D25M Camera Manual Operating the Camera
65. d via the Ethernet cabling using standard PoE products MOBOTIX AG e Security Vision Systems Made in Germany www mobotix com sales mobotix com D25M Overview Model Versions The D25M is available in the Secure IT or Basic models which all come with different features The D25M is delivered with an L25 Super Wide Angle lens horizontal angle of 82 as standard Four additional lenses Wide Angle and Telephoto with viewing angles of 13 27 40 or 55 are available upon request The standard IT and Secure models include a pre formatted and pre installed 4 GB MicroSD card Audio features can be added at any time with the ExtlO module not available for Basic model Basic and IT Cameras Maximum Image Size Is Now HD Instead of VGA The D25M Basic and IT models now generate HD images 1280 x 720 pixels instead of the VGA images of predecessor models 640 x 480 pixels The special quality advantage of a MOBOTIX Basic IT camera with HD resolution 1280 x 720 The HD images of a MOBOTIX are generated by the high resolution image sensor with 2592 x 1944 pixels and are optimized and scaled down for the HD format Because of the high resolution sensor the generated images especially with respect to quality and light sensitivity are noticeably superior than regular HD cameras that are only using a simple HD sensor with 1280 x 720 pixels MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sale
66. ddress or DNS name of a MOBOTIX camera or a third party IP camera if it was not found by the automatic search feature e MxPEG clip Adds an MxPEG video clip previously recorded by a MOBOTIX camera as a video source e Recording path Adds the path of an external file server where a MOBOTIX camera has recorded audio video data The videos or images recorded at that location can now be played back using the Player or Video Search MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com 108 140 D25M Camera Manual Operating the Camera Editing the Video Source List Right click on this list to open a shortcut menu from which you can select all video sources or cancel the selection You can also use this method to remove from the list some or all of the video sources that you would not like to display or manage in MxControlCenter Add Video Sources Name IP Address Path Type mx10 3 30 151 10 3 30 151 D120 Jmx10 8 85 os 24h mx10 8 52 rn 24h Deselect all Remove Remove all If you have cancelled the camera configuration process or need a password that differs from the camera s factory default password you can also configure the camera from the shortcut menu at a later date and enter the user name and password required for reconfiguration at that time It is also possible to open the Configure selected cameras dialog box using the shortcut menu in order to change the camera networ
67. de for solutions that can be tailored for many different application scenarios This robust dome camera IP65 can also be ordered with optional Vandalism On Wall and In Ceiling sets The introduction of the newest five megapixel sensor technology with increased light sensitivity not only generates more brilliant images with more details it also delivers color images of higher quality under lowlight conditions Another improvement The D25M IT now generates HD images 1280 x 720 pixels instead of the VGA images of predecessor models 640 x 480 pixels Another plus the improved light sensitivity of the 5MP sensors which drastically reduces exposure times In conjunction with MxLEO the exposure and image optimization program working in the background the camera generates perceptibly better and more detailed images especially under low light conditions This significantly reduces motion blur that is typical of longer exposure times with little light and thus provides much more image detail faces license plates etc for proper identification You can download the MOBOTIX video management software MxEasy and MxControlCenter and the manuals from the MOBOTIX website www mobotix com gt Support gt Software Downloads For the iPad iPhone and iPod touch iOS devices MOBOTIX offers the MOBOTIX App a free of charge mobile solution that is easily found when searching for MOBOTIX AG in the App Store If you have any questions our suppo
68. e image while the camera is e g recording full images at 1 fps in MEGA or QXGA resolution When using MxEasy or MxControlCenter the recorded full images may be prepared for the user using vPTZ functions e g panning and zooming in on an image detail such as a doorway If full image storage is not activated only the last displayed live image will be saved save what is seen The main benefit of live image storage is to ensure that the full power of the camera processor is used for live image correction and maximum image rates The main advantage of full image storage lies in the special functionality of the D25M in that it can always maintain availability of a maximum size full image for later investigation despite vPTZ actions carried out on the live image The mechanical limitations of motor driven PTZ cameras mean that they simply cannot provide this unique advantage to the user MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com Virtual PTZ and Full Image Recording 121 7140 Activate Deactivate Full Image Recording in the Browser To configure this feature open the Setup Menu Event Control Recording dialog and activate or deactivate the Full Image Recording option 7 MOBOTIX Q24 mx10 8 0 113 Recording General Settings Value Arming Enable E no time table FS Digital Signing on is Recording Status Symbol or TE Terminate Recording TR or i3
69. e buttons multifunctional sliders developed by MOBOTIX as well as simple gestures like swipe and tap making it easy for newcomers and older users to work with professional security equipment In addition using mobile devices to operate the various functions such as door opening activating the voice mailbox switching the door bell off at night and switching a light on off creates added value in the form of greater convenience and security in every day life MOBOTIX App Mobile Remote Station for MOBOTIX Cameras and Door Stations Bandwidth optimized remote access via WLAN WiFi or the Internet Live images and recordings in the best MOBOTIX HiRes quality Two way communication door opening and video mailbox access Doorbell and alarm notifications protection of privacy Convenient search functions playback of external MxPEG videos Grouping of cameras and filtering of events Free from the App Store for the iPad iPad mini iPhone and iPod touch MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com P 4 Available on the App Store Free download from the App Store No license fees Free updates 48 140 D25M Camera Manual Installation 2 INSTALLATION Although the D25M is primarily designed for installation on walls and ceilings it can also be mounted to a pole or the corner of a building for example using the appropriate MOBOTIX accessories 2 1 Preparing the I
70. e cameras always obtain the same IP addresses by permanently assigning the MAC addresses of the cameras to the desired IP addresses MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com In case of an error the camera uses its last IP address 114 140 D25M Camera Manual Operating the Camera 3 3 Adjusting Lens Focus and Correcting Lens Distortion 3 3 1 Aiming and Adjusting the Lens Make sure that you see the live image of the camera on the monitor of your computer or laptop Now adjust the lens mount until you see the desired image area on your monitor e Remove the camera dome Use the supplied plastic foil or a cotton cloth to remove the dome by turning it in a counter clockwise direction With IT Secure models you may have to remove the outer shell first e Loosen the toothed ring slightly by turning it in a counter clockwise direction using the supplied hook wrench In addition loosen the two Allen screws on both sides of the lens mount slightly by turning them in a counter clockwise direction using the supplied Allen wrench Loosen the ring and screws until you are still able to pan and rotate the internal part of the camera with the lens without much force but not so far that the lens is unable to move on its own e Now aim the camera by rotating and panning the lens mount Note the MicroSD card slot must point downward for the camera s live image to be displayed
71. e on site network cable to the network cable passing through the On Wall Set using a standard connector Make sure to leave enough unused cable inside the housing This will ensure that you can turn and tilt the lens mount freely later on Excess cable can be easily stored within the On Wall Mount 0 8 Attach the camera to the mount Press the D25M so that it is seated firmly within the On Wall Mount The tapered guides at the back ofthe D25M housing fit exactly into the openings ofthe On Wall Mount Attach the white outer shell with the supplied Allen screws without rubber seal once the lens has been adjusted 9 Proceed to Section 3 3 1 Aiming and Adjusting the Lens MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com Mounting the Camera with the In Ceiling Set 67 140 2 4 Mounting the Camera with the In Ceiling Set x P 2 4 1 Mounting Instructions The In Ceiling Set offers the most stylish installation option for the D25M When properly installed the only visible component is a particularly sleek and discreet dome camera while most ofthe remaining components are concealed inside the ceiling Only the compact dome and the thin decorative ring that conceals the screws can be seen For these reasons the D25M installed with the In Ceiling Set is the preferred option for most indoor spaces frequented by customers or the general public e g hotels resta
72. e the camera position the position of the cable outlets and the method of power sup ply have been decided upon the cabling can be installed Before installing the MOBOTIX D25M you should make sure that the network connections have been properly tested so that the proper functioning of the camera is guaranteed If the camera is to be installed outdoors you should also install the MOBOTIX MX Overvoltage Protection Box optional accessory This interface box not only provides overvoltage protection of up to 4 kV for MOBOTIX IP cameras it also provides simple and weatherproof connection of the cameras to a network patch cable RJ45 variant or a network installation cable LSA variant For additional information on the MX Overvoltage Protection Box open the Products Accessories gt Interface Boxes section on www mobotix com MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com UPS units not only pro tect the camera against power failures they also protect all other con nected network devices against damage from voltage peaks and lows MOBOTIX 2 Overvoltage Protection c 9 ur e MOBOTIX Overvoltage Protection 2 G 6 54 140 D25M Camera Manual Installation 2 1 5 Wiring Fire Prevention Lightning and Surge Protection When installing the wiring inside or outside of buildings make sure you always adhere to the relevant regulations on wiring
73. elete cycles of every storage cell of a flash device is limited The controller of the flash device automatically detects individual flash cells that are no longer functioning The contents of the faulty cell will then be rebuilt using a checksum and will be moved to a properly working spare cell The faulty storage cell will be marked as bad and will no longer be used No data is lost in this process In addition MOBOTIX cameras constantly monitor activated flash storage devices MOBOTIX has developed a technology to test the wear of the flash device by logging the number of write delete cycles patent pending The flash memory wear is automatically displayed in the status bar in the live camera image but it can also be viewed at any time in the Admin Menu Camera Status dialog box Conservative Memory Usage Thanks to MOBOTIX MxFFS File System MxFFS formatting of the MicroSD card means that MOBOTIX camera software will use the flash device as evenly as possible thus allowing for the maximum possible number of write delete cycles This also means that all storage cells of the flash device will be written and deleted with the same frequency if possible MOBOTIX technology increases the life of the flash device considerably and also improves the security and the reliability of the storage process Storage Requirements and Life Expectancy of MicroSD Cards The life expectancy of a MicroSD card increases proportionally to the storage capacity
74. elivered Parts and Dimensions 1 3 1 D25M IT Secure T 1 12 1 1 10 o 1 8 O emm O Q8 w e 1 16 de 1 5 AIT 5 J Item Count Part Name 1 1 Camera housing 12 Lens pre installed 13 Lock ring pre installed 1 4 Dome transparent 1 5 Ethernet cable CAT5 0 5 m 20 pre installed 1 6 Allen wrench 3 mm 1 7 Toothed wrench 1 8 Outer shell with rubber seal 1 9 Mounting ring 1 10 4 Dowels 8 mm 11 4 Stainless steel washers 5 3 mm 1 12 4 Stainless steel wood screws with Torx head 4 5x60 mm 1 13 Torx wrench TX20 1 14 4 Stainless steel Allen screws M4x16 mm 1 15 4 Stainless steel washers 4 3 mm 1 16 Single wire plug black MxBus 1 17 2 Single wire connector 1 18 MxBus connector with two wire connection line MOBOTIX AG e Security Vision Systems Made in Germany www mobotix com sales mobotix com Delivered Parts and Dimensions 3 140 Camera Housing and Connectors The MOBOTIX D25M IT Secure consists of the camera housing mainboard lens dome the outer shell and the mounting ring Connections Network Ethernet network incl PoE power supply MxBus for MOBOTIX expansion modules e g MX GPS Box MX 232 IO Box USB e g for ExtlO MX 232 IO Box Slot for MicroSD card Outer shell 2 Lens R L LEDs Slot for MicroSD card MxBus gt m USB 83 Nefwork c
75. es and is corrected accordingly The scroll wheel can be used to control the zoom function This functionality is disabled in the default settings of the camera and must therefore first be activated To do so go to Setup Menu vPTZ Settings and uncheck the Lock Mouse Wheel Zoom item Then save the settings by MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com Virtual PTZ and Full Image Recording 119 140 clicking Set and Close You can now use the scroll wheel to zoom roll upwards or zoom roll downwards Operation Using a USB Joystick A standard USB joystick can drastically facilitate vPTZ operation for the user in the browser in MxEasy and in the MxControlCenter however MxCC is also equipped with a virtual joystick that can be operated using the mouse Please first install the joystick on the PC according to the manufacturer s instructions In order to use a USB joystick in the browser make sure that you have a PC with a Windows operating system and the latest version of Internet Explorer and that the ActiveX mode in the camera software browser is activated MOBOTIX e Select Browser in the Quick Control e In the dropdown to the right of to Browser select the Activex option The USB joystick can then be used until the browser is closed e f you want to store this setting permanently open Admin Menu gt Language and Start Page and in Page Opt
76. etwork Power is supplied directly via the network cable see Section 2 1 3 2 Set up the camera s network parameters Manually using a web browser see Section 3 2 1 then Section 3 2 2 Automatically using MxControlCenter MxEasy see Section 3 2 3 and 3 2 4 or via DHCP see Section 3 2 6 3 Configure the camera using the browser based user interface Every MOBOTIX camera comes preconfigured with a fixed IP address in the 10 x x x range e g 10 8 0 99 However local computer networks usually have IP addresses in the 172 or 192 ranges In order to access a MOBOTIX camera via the network the camera needs to obtain an IP address in the same address range You can set up the network parameters of the MOBOTIX camera using one of the following methods Manually using MxCC and MxEasy or by DHCP MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com Manual and Automatic Operation Overview 97 140 3 1 1 Manually Using a Computer in the 10 x x x IP Address Range You can set up the camera s network parameters using a browser and the embedded NEU IP address of your camera is printed camera software To do this connect the camera to a computer or a network that is using EE Cer on the a 10 x x x IP address range see Section 3 1 1 Manually Using a Computer in the 10 x x x back of the camera IP Address Range Oncethishas eee been completed youcanenterthe vt OLX
77. f the live image that is visible or the full sensor image full image storage This also allows you to examine parts of an image or video that had not been visible in the live image section on display at the time of the recording Unlike in the camera systems from other manufacturers there is no need to buy an install additional software on your computer thanks to the MOBOTIX firmware that can be accessed directly in a web browser via the camera IP address Instead of using a web browser you can also download the free MxControlCenter or MxEasy video management software from the MOBOTIX website www mobotix com gt Support to quickly display multiple cameras on one monitor or on an entire video wall switch alarms with sound or conveniently search for an event The MOBOTIX App for iOS devices iPhone iPad iPad mini iPod touch iOS version 5 0 and higher is also available free of charge from the App Store for your mobile applications MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com MOBOTIX Software 45 140 1 5 2 MxControlCenter The MxControlCenter video management software can be used to combine any number of cameras at any locations into a well structured and powerful video security system with centralized or local access protected operation and analysis The state of the art software specifically tailored to support high resolution MOBOTIX network cameras provides a user
78. for example the exact time at which these people entered the image area recorded by the camera A browser Internet Explorer with MxPEG ActiveX plug in MxControlCenter or MxEasy can be used to examine the recorded sequences v zj Stored Full mage The image distortion caused by the L25 82 Wide Angle lens can be corrected Since this function requires more computing power it should not be enabled in the live image for applications that require a maximum frame rate The image distortion in the recording can also be corrected at a later time MOBOTIX AG e Security Vision Systems Made in Germany www mobotix com sales mobotix com Integrated vPTZ func tions allow the complete stored full image to be analyzed at a later point in time in MxEasy and MxControlCenter 16 140 D25M Camera Manual Product Overview 4 GB MicroSD card pre installed in the camera D25M IT Secure Internal DVR The D25M IT Secure model features direct recording to integrated MicroSD cards which makes the camera fully independent of any external storage media even for longer periods of time The camera internally stores high resolution video without requiring an external recording device or PC and therefore without overloading the network whatsoever Old recordings may be overwritten automatically or auto matically deleted after a specified period of time A 16 GB MicroSD card for example allows the camera to store more th
79. g areas Admin Menu in the Hardware Configuration profiles for signal output Transfer Profiles FTP e mail network messages and Sound and VolP Telephony sound profiles VoIP profiles For more information refer to the online help for the Action Group Overview dialog box e Activate shock detector The D25M is also equipped with a shock detector as stan dard for all IT and Secure models If for example the camera s housing receives a blow it automatically registers it and sends a notification via a network message or telephone call A general advantage is that MOBOTIX cameras are extremely tough because of the absence of mechanical moving parts This allows them to stay fully operational when they are subject to strong vibrations Open the Setup Menu gt Event Control gt Environment Events gt Edit dialog box if you would like to activate the shock detector and any other sensors MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com 132 140 D25M Camera Manual Operating the Camera The microphone can be irreversibly deactivated 3 7 Additional Notes 3 7 1 Weatherproofness The MOBOTIX D25M IT Secure models have been certified weatherproof according to IP65 absolutely dust proof and resistant to water jets and can also be wall mounted outdoors The MOBOTIX D25M Basic has attained a protection class of IP54 3 7 2 Password for the Administration Menu Accessing the admin
80. g the backup system e Waiting for key pressed Both LEDs light up for four seconds If you press the R or L key of the camera during this time the camera will execute the corresponding func B o e tion see Section 3 2 6 Starting the Camera with an Automatic IP Address DHCP and Section 3 2 5 Starting the Camera with the Factory IP Address Use a suitable device to press a key a ball point pen for example e Ready Once the camera software has been started the green LED is on permanently E and the red LED blinks You can now reach the camera via the network using a browser PB e Q During the startup sequence of the camera the LEDs will always light up even if they have been deactivated in Admin Menu LED Setup MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com 96 140 D25M Camera Manual Operating the Camera Download the MxEasy and MxControlCenter software for free at www mobotix com Camera software in the browser 3 OPERATING THE CAMERA 3 1 Manual and Automatic Operation Overview MOBOTIX cameras do not require any extra software Thus you can set up and operate the MOBOTIX camera using a JavaScript enabled browser on all common operating systems such as Window Linux Macintosh etc As an alternative you can also use the MOBOTIX applications MxControlCenter and MxEasy Follow these steps to set up the camera 1 Connect the camera to the n
81. he outer shell is required at a later stage in the installation and is attached only when the dome has been removed and placed back after a lens adjustment 7 Proceed to Section 3 3 1 Aiming and Adjusting the Lens MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com 60 40 D25M Camera Manual Installation 2 2 4 Procedure for D25M Basic 1 Unscrew the transparent dome of the camera in a coun ter clockwise direction To keep the dome clean use the enclosed plastic foil or a lint free cotton cloth 2 Unplugthe pre installed network cable from the network connector inside the camera Never touch electronic components as the static electricity may damage them 3 Loosen the internal part of the camera by releasing the two blue clamps with the thin side of the hook wrench Now turn the toothed ring in a counter clockwise direction using the other side of the hook wrench MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com Mounting the Camera Without Accessories 61 140 4 Remove the internal part of the camera with the lens mount from the base of the camera 5 Position the base of the camera housing over the drilled holes and the prepared cable exit Please make sure that the camera baseis relatively flush with the sur face The network cable with connector should be flush with the ceiling or wall as a result
82. hers and M6 nuts included with the Corner and Pole Mount and 1 attach the Wall Mount to the Corner and Pole Mount N e Continue with the remaining work steps as described in Section 2 6 Installing the Wall Mount MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com 86 140 D25M Camera Manual Installation Push push operation only remove the MicroSD card after first gently pushing it in 2 8 Replacing the MicroSD Card The camera must be taken down to remove insert or ele replace a MicroSD card To avoid data loss be sure to deactivate MicroSD card recording in the camera software and reboot the MOBOTIX camera before k removing the card Caution A MicroSD card may only be removed from the camera after you have deactivated recording to a Flash device and rebooted the camera Failing to do so may lead to data loss Before inserting the MicroSD card make sure that it is not write protected 2 8 1 Removing a MicroSD Card e Deactivate recording Recording to MicroSD card must be deactivated Admin Menu gt Storage on External File Server Flash Device If MicroSD card recording is still active deactivate recording and reboot the camera Section 3 5 MicroSD Card Recording contains more information on this topic e Remove the outer shell Remove all four Allen screws using the supplied Allen wrench Take off the outer shell e Remove the c
83. il MOBOTIX AG e Security Vision Systems Made in Germany www mobotix com sales mobotix com Additional Notes 133 140 3 7 5 Resetting the Camera to Factory Settings All settings of the MOBOTIX camera can be permanently reset to the factory default settings This makes sense if for example you have obtained a camera without any information or you would like to reset all settings after testing the camera In order to perform this procedure you need to have access to the administration area of the camera admins group Open Admin Menu gt Reset to reset the camera to factory defaults All defined users are deleted and the admin password is reset to the factory default when you reset the camera using Admin Menu Reset If you want to maintain the existing users use the method described in Section 3 2 5 Starting the Camera with the Factory IP Address 3 7 6 Activating Event Control and Motion Detection In its default configuration the camera s event control and video motion detection features are not enabled In order to activate event controlled recording open Setup Menu General Event Settings and activate the Arming switch Another method is to click on the Arm amp Record softbutton in the browser s user interface The camera displays the motion detection window in the live image dotted frame in the center and the camera auto matically stores images as soon as the motion detection window detects movemen
84. installed high quality 4 GB MicroSD card once a year if you have it constantly set to continuous recording Monitoring the Cell Wear of Flash Storage Devices Patent Pending File Server Flash Device MOBOTIX uses its own technology for this 6 SD Flash Card purpose and has a pending patent You can CI view the flash wear in the status bar of the live 7777 U 0 O 0 max 0 image or by opening Admin Menu gt Camera 8 Status dditi th d Lost Event Images 0 atus In addition the camera can also send Sequences 1 1 files a warning message for example via e mail Newest Sequence 1970 01 01 01 00 00 0 as soon as a critical error is detected when Sequence 1970 01 01 01 00 00 0 Current Usage 4 0 MBytes 0 4 data is written to the SD card Admin Menu gt max size 936 MBytes Error Notification Function The MicroSD card can then be replaced to ensure that any exist ing data is not lost MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com 124 140 D25M Camera Manual Operating the Camera Format SD card Admin Menu gt Storage on External File Server Flash Device 3 5 2 Formatting the MicroSD Card Before a MOBOTIX camera can store image and video sequences on a MicroSD card the card needs to be formatted as MxFFS MicroSD cards supplied by MOBOTIX are already MxFFS formatted The following steps are necessary to format a st
85. ions gt Operating Mode select Activex Gott Live pem e Live into Live fast APT OC SE e f you want fo store the current settings permanently click on Set and Close at the bottom of the dialog and approve storing the settings when prompted Player info Cverts AP OC 9 Mutiioa ints Live slew Image Link Everts API OC 58 Muta Muroa image Lek Evans POA mc Live stow mage Link Events PDA OC 88 ER POA ime Le sow image Lec Ovens am ioc SO Page Design Dacwycudivage gt Ov ash brags IO Page Ostiors Language em 15 image PutOows merus sron TE e The joystick can now be used Fotos Rate tor Guest Manun Delaur Access TED ife Remarks Oy set Pe Cure ive rage wit 93 06 cse ute No 20068 10 adeo qt etve o camen hn tacos Live Fragen aim meres 1 changing rage Parameters anc Acton keys Arcest w CONN NST ac ve 190078 Passo 0 00 Peay SOCA vert CHA QU image UOS VOR eoo de up Don Acces Ihe enhanced voro Manageme tows Gatabete DOCA event Gowniced ex brager o everts of Pre and other MOGCTI X cameras erenged in 3 awt ways Live Frage aas age asd auem iat of he and oer MOQGOT X carvers Live reges V Ire rescivtio evoen Lit of events in a compact ajout eiecti the Dacia Cu mage fof Ue 202 anc De user Parie YOu Can cse Caio mages dy using ter e camera r fe Mason brea fin sacs
86. istration menu of the camera Admin Menu button is only possible after entering a user name and password e Factory default user name is admin e Factory default password is meinsm The Quick Installation assistant automatically appears when the administration menu is accessed for the first time It provides an easy method to adjust the basic camera set tings to the current application scenario For security reasons it is highly recommended to change the default administrator password after the camera has been properly configured Enter the user name and password exactly as shown above Note that all entries are case sensitive Make sure that you store information on user names and passwords in a secure place If you lose the administrator password and cannot access the Administration menu the password can only be reset at the factory This service is subject to a service charge 3 7 3 Permanently Deactivating the Microphone Deactivating a camera s microphone may be necessary in order to protect the privacy of persons at a workplace or for other reasons You can permanently and irreversibly deac tivate the microphone in the Admin Menu Loudspeaker and Microphone dialog box 3 7 4 Starting the Camera with the Factory IP Address If the camera s IP address is not known you can start the camera with its factory IP address Section 3 2 5 Starting the Camera with the Factory IP Address describes this procedure in more deta
87. ith angled plugs can be used for the D25M 1 4 9 MiniUSB Cable to MiniUSB Angled Angled Order no MX CBL MU EN PG EN PG 05 2 5 straight angled The MOBOTIX ExtlO can be connected directly to the A D25M with this cable which is up to five meters long 1 4 10 MiniUSB Cable to USB A Socket Order no MX CBL MU EN PG AB 05 2 5 USB based storage media for example USB hard drives can be connected directly to the D25M with this cable which is up to five meters long 1 4 Ethernet Patch Cable for Bayonet Catch Order no MX OPT CBL LAN 1 2 5 10 length 1 m 2 m 5 m 10 m The MOBOTIX developed special cable can be installed in a waterproof manner and has an integrated sealing gasket Every D25M ships with a 0 5 m long cable as standard which can be exchanged for a patch cable up to 10 m in length 1 4 12 NPA PoE Set Order no MX NPA PoE EU and MX NPA PoE INT Version EU and Version INT Order no MX CBL NPA BAT 2 battery cable for mobile voltage sources Thisis a multifunctional PoE injector according to the IEEE 802 3af standard with three connectors for network camera PoE device PC universal power supply unit with interchangeable adapter plugs and crossover func tion The NPA PoE Set connects and remotely supplies a D25M with power via an Ethernet cable up to 100 m in length The blue adapter can also be connected to mobile voltage sources from 12 to 57 V DC by means of an additionally available battery
88. ix com MOBOTIX EJ Db 33 iS Acorn Vers o ib 9 f m tme ihm rm i8 tom ome samso e EIL sn Live screen http camera IP gt control userimage html Player screen http camera IP control player oO ap MultiView screen http camera IP gt control multiview PDA screen http camera IP gt pda PDA Event List http camera IP gt control player eventlist amp pda Guest screen http lt camera IP gt cgi bin guestimage html 104 140 D25M Camera Manual Operating the Camera Download MxControlCenter for free from www mobotix com 3 2 3 First Images and Network Parameter Configuration in MxControlCenter File View Layowt VideoSource Recording Toots Help aS vi oe 0 0 oz F E 1 Y I ui 4 p Eu 1 4 i Overwien Outside U 4 B if 1 L p a p Basane 1 cays ei d LE fc gt A EI PTZ Controis MxCentroC ente Fre 53 bk 2 12 52 38 Fri 25 02 11 Installation Download the setup file from the MOBOTIX website to install the latest version The latest versions are available at www mobotix com in the Support gt Software Downloads gt MxControlCenter section To install MxControlCenter simply double click on the setup file and follow the instructions The selected files are copied to the computer older versions will be removed automati cally and the designated shortcut
89. ix com sales mobotix com First Images and the Most Important Settings 113 140 3 2 6 Starting the Camera with an Automatic IP Address DHCP Under certain circumstances you may have to reset the camera to its factory IP address This could be the case for example if the IP address has been lost or the camera does not respond to the last known IP address Proceed as follows to start up the camera with its factory IP address 1 If the camera is powered on disconnect the power supply by unplugging the cor responding cables and then reconnect the power supply Wait until both LEDs light up simultaneously for the first time Press the R key within the next four seconds and hold it down if you need to try again go back to Step 1 Use a suitable device to press a key a ball point pen for example 4 After about 30 to 45 seconds the camera emits a double sound boing boing The camera has finished booting and can now be used e g MxEasy MxControlCenter MOBOTIX App web browser Starting the camera with an automatic IP address DHCP is only temporary The network configuration of the camera can be permanently set to DHCP under Admin Menu gt Ethernet Interface Make sure that the network has a functioning DHCP server when starting the camera with DHCP support If this is not the case the camera cannot obtain a valid IP address and will use its last IP address You should also make sure that th
90. k parameters Creating a New Layout Select the camera or other video sources that you would like to display in a layout a view with a group of selected cameras in the Add video sources dialog box and then click on Add selected video sources Create New Layout es You have chosen to add 2 video source s Generate new grid layout for selected video sources Name EEE Only add video sources to system do not create layout Ca ems The Create new layout dialog box is displayed If you select the Generate new grid for selected video sources option here MxControlCenter automatically generates a grid layout t