EK Water Blocks EK-DCP 4.0 X-RES
Contents
1. Installation and mounting manual for EK DCP 4 0 X RES Reservoir Pump Combo This product is intended for installation only by expert users Please consult with a qualified technician for installation Improper installation may result in damage to your equipment EK Water Blocks assumes no liability whatsoever expressed or implied for the use of these products nor their installation The following instructions are subject to change without notice Please visit our web site at www ekwb com for updates Before installation of this product please read important notice disclosure and warranty conditions printed on the back of the box Before you start using this product please follow these basic guidelines 1 Please carefully read the manual before through before beginning with the installation process 2 The EK High Flow and EK PSC or EK CSQ type fittings require only a small amount of force to screw them firmly in place since the liquid seal is ensured by the rubber O ring gaskets 3 The use of quality market proved corrosion inhibiting coolants is strongly recommended for any liquid cooling system Unscrew the original M3 screws with Philips head screwdriver and store them in a safe place These screws will not be needed any more Use four enclosed M3x8 DIN 7991 countersunk screws and attach the interconnecting metal plate to the base with enclosed Allen key 2mm In order to connect the reservoir and the pump p2. commercial purposes III the product has not been misused handled carelessly or used in a manner other than in accordance with the instructions provided describing its installation and proper use This warranty does not confer rights other than those expressly set out above and does not cover any claims for consequential loss or damage This warranty is offered as an extra benefit and does not affect your statutory rights as a consumer This warranty is voided if the product comes in contact with aggressive UV additives or other improper liquids REQUIRED TOOLS Philips head screwdriver Power drill with 4 mm drill bit optional Revision 1 0 Released on 2 of October 2013
3. l plate on In order to make air bleeding process easier one can install the enclosed PU mesh in the reservoir using enclosed Allen key 2 5 mm the inlet compartment of the X RES en Secure the metal plate through the openings to the computer chassis e Water out using enclosed M4x6 ISO 7380 screws washers and M4 nuts User may need to drill 4 four 4 mm holes through chassis metal using electric power drill if there are no appropriate mounting holes available Screw M4x4 DIN 7984 DCP 4 0 Pump Metal plate Plastic foam E Rubber anti vibration dumper Water in ww l See Q euut Use these zip holes to mount the X Res to the PC chasis using enclosed M4x6mm screws and Connect two G1 4 threaded fittings to the reservoir IN suction and pump OUT pressure Please note the water flow orientation EKWB recommends using EK CSQ fittings and EK CSQ Adapters with the EK DCP 4 0 X RES series reservoirs To ensure that the tubes are securely attached to the barb fittings please use hose clamps or an appropriate substitute Unscrew the top cap and fill the coolant in the reservoir Make sure the liquid is not spilled over your computer or any electrical devices nearby Run your pump Shortly for couple of times to make sure water floods your tubes and other water cooling components Repeat the procedure until you are done and pay attention to the water level in your reservoir Lowest level of the coolant sho
4. lease follow these steps a ee ATTENTION i 1 Install the provided gasket O ring l Pay special attention 19 x 2 mm into the milled groove as i to orientation of the shown on the picture below Failing interconnecting metal to do this will cause serious leakage i plate I gt The screws head i Use four enclosed M3x8 DIN 7991 I must be aligned i countersunk screws and attach I flushed with the i pump to the reservoir with enclosed l metal plate i Allen key 2 mm Se p a a a a re ee rr ATTENTION CAUTION Be extremely careful not to over tighten the M3 screws Doing this may strip the thread and render product useless m e E I oe TROUBLESHOOTING If the threaded holes do not align please re check STEP 2 in the manual If the screw head does not align flush with the metal plate please re check STEP 2 in manual M3 x 16 screws Revision 1 0 Released on 2 of October 2013 Screw in the four 4 rubber vibration dampers into the threaded holes The EK DCP 4 0 X RES offers three inlet suction G1 4 ports In order to use the on the bottom side of the reservoir Do not use any tools to fasten the selected port as inlet it is mandatory to use the enclosed EK Extender G1 4 with the dampers in to position use thumbs only G 4 threaded fitting Use enclosed G1 4 Plugs to plug the remaining two unused ports Then use enclosed M4x4 DIN 7984 screws to install the meta
5. uld be at least 1 cm above the plastic Acetal base of the reservoir The highest recommendable water level is approximately 0 5 cm below the top of the acrylic tube Once done with the filling process please close your EK DCP 4 0 X RES by reinstalling the end cap twisting it clock wise VERY IMPORTANT NOTICE Once the installation is completed it is a recommended practice to test the cooling circuit for leaks prior to powering up the computer We recommend a 24 hour leak test prior to powering up the computer Do not test the product using tap water pressure This will rupture the top of the housing and render the product unusable and will void your warranty While all efforts have been made to provide the most comprehensive tutorial possible EK Water Blocks assumes no liability expressed or implied for any consequential damage s occurring to your equipment as a result of using EK Water Blocks cooling products either due to errors or omissions on our part in the above instructions or due to failure or defect in the EK Water Blocks cooling products WARRANTY Our products are warranted against defects in materials or workmanship for a period of 24 months beginning from the date of delivery to the final user During this period products will be repaired or have parts replaced at our discretion provided that 1 the product is returned to the agent from whom it was purchased II the product has been purchased by an end user and has not used for
Download Pdf Manuals
Related Search