DELL Latitude E5440
Contents
1. Align the keyboard trim to its place Press along the sides of the keyboard trim until it snaps in place 15 3 Install the battery 4 Follow the procedures in After Working Inside Your Computer Removing the Keyboard 1 Follow the procedures in Before Working Inside Your Computer 2 Remove a battery b keyboard trim 3 Remove the screws at the back of the computer and flip the computer over 4 Remove the screws that secure the keyboard 1 and lift the keyboard from the computer 2 and 3 16 5 Disconnect the keyboard cable and remove the keyboard from the computer Installing the Keyboard Connect the keyboard cable to the keyboard 2 Place the keyboard into its place until all the metal tabs fit into their positions Press down on the keyboard to the left and right side ensuring that all the snaps are fully engaged with the computer 4 Install the screws to secure the keyboard to the palmrest 5 Install the screws at the back of the computer 6 Install a keyboard trim 17 7 b battery Follow the procedures in After Working Inside Your Computer Removing the Base Cover 1 2 Follow the procedures in Before Working Inside Your Computer Remove the battery Perform the following steps a Remove the screws that secure the base cover b Slide the base cover towards the front of the system and remove it from the computer Installing the Base Cover 1 22. C 40 F to 149 F non condensing 5 to 95 non condensing 15 24 m to 3048 50 ft to 10 000 ft ft 15 24 m to 10 668 m 50 ft to 35 000 ft G1 as defined by ISA 71 04 1985 6 Contacting Dell NOTE If you do not have an active Internet connection you can find contact information on your purchase invoice packing slip bill or Dell product catalog Dell provides several online and telephone based support and service options Availability varies by country and product and some services may not be available in your area To contact Dell for sales technical support or customer service issues Visit dell com support Select your support category Verify your country or region in the Choose a Country Region drop down menu at the top of page PWN P Select the appropriate service or support link based on your need 65
3. Description Allows you to enable or disable the Intel Virtualization Technology Enable Intel Virtualization Technology default Enables or disables the Virtual Machine Monitor VMM from utilizing the additional hardware capabilities provided by Intel Virtualization technology for direct I O Enable VT for Direct I O enabled by default This option specifies whether a Measured Virtual Machine Monitor MVMM can utilize the additional hardware capabilities provided by Intel Trusted Execution Technology The TPM virtualization Technology and Virtualization technology for direct I O must be enabled to use this feature Trusted Execution disabled by default Table 11 Wireless Option Wireless Switch Latitude E5440 Latitude E5540 Wireless Device Enable Latitude E5440 Latitude E5540 Table 12 Maintenance Option Service Tag Asset Tag Table 13 System Logs Option BIOS Events Thermal Events Power Events Description Allows to set the wireless devices that can be controlled by the wireless switch The options are e WWAN e WLAN e WiGig e Bluetooth All the options are enabled by default e WLAN e WiGig Bluetooth All the options are enabled by default Allows you to enable or disable the internal wireless devices e WWAN e WLAN WiGig e Bluetooth All the options are enabled by default e WLAN WiGig e Bluetooth All the options are enabled by default Descri
4. Allows you to enable or disable the computer from turning on automatically when an AC adapter is connected Default Setting Wake on AC is not selected Allows you to set the time at which the computer must turn on automatically The options are e Disabled default e Every Day e Weekdays e Select Days Allows you to enable USB devices to wake the system from Standby K NOTE This feature is only functional when the AC power adapter is connected If the AC power adapter is removed during Standby the system setup will remove power from all of the USB ports to conserve battery power e Enable USB Wake Support e DEnable USB Wake Support is not selected Allows you to enable or disable the feature that automatically switches from wired or wireless networks without depending on the physical connection e Control WLAN Radio e Control WWAN Radio e Control WLAN radio or Control WWAN radio is not selected default Allows you to enable or disable the feature that powers on the computer from the Off state when triggered by a LAN signal e Disabled This option is enabled by default e LAN Only e WLAN Only e LAN or WLAN LAN with PXE Boot This option lets you block entering to sleep S3 state in Operating System environment Block Sleep S3 state This option is disabled by default This option enables you to minimize the AC power consumption during the peak power times of day After you enable this option your system
5. Base Cover ss nota ea De te eet ee 18 Removing the Optical Drive seccicccccicecesdeaciasscedecacedecacancaseaeenaviedccuacisesceddvactectredaecdeddessoeensunannsedenastoess 18 Installing the Optical Drive ecc i e EL HR RR AE ete D Rudd 19 Removing the Hard Drive c ccccccssssesscesscessecseecseecsseceseesseecseecseecsaeceseeessecsesesaeceseseseeeseesseessaeseeeeeas 20 Installing the Hard Drive 1er at d i CHE re teed ec ER dde e oe deve dde d 20 Removing the Memory Module sssssssssssseseeeseeeeenenennennn nnne n nennen ntnetrns denn nnns tnn nnn nennnn sens 21 Installing the Memory Module ssssessssssssssseeeeese nennen aa aaa eee e sns enhn snnt aaa tenens senden nnn n nna 21 Removing the WEAN Card nde ee pr RA ay eo bep e Pus 22 Installing the WLAN Cardh c ccccccscssscsssccssecssecssecsseesseecseecseecseecaecesescaeseseeesueseaeseaesessesseesseesensesstess 22 Removing the Coin Cell Battery cccccccccssscssecssescsscesesessesseecseeesseesseesseeceeecseecsaeseaeseseesseesseesaeesas 22 Installing the Coin Cell Battery irii arearen aiaia eaaa Ta aa KAEO a NEA AANE eaaa aA 23 Removing the Display Hinge seessessseseeeenneeeenen nennen nnne nennen nnne nnne nnne nnne nn nennen nnns 23 Installing the Display Hinge 1e eee t bi ede E Ea EC dere een cett 24 Removing the Palmire Sta nean eeraa aaeeea a aa aa e a n aean aaaea eai aa aaar 24 Installing the Palmrest 2 ne a Tg e
6. 3 4 Slide the base cover into its slot until it clicks into place Install the screws that secure the base cover to the computer Install the battery Follow the procedures in After Working Inside Your Computer Removing the Optical Drive 1 2 18 Follow the procedures in Before Working Inside Your Computer Remove a battery b base cover Perform the following steps a Remove the screw that secures the optical drive to the computer b Push the optical drive away to remove it from the computer 4 After removing the optical drive bracket perform the following steps a Remove the screws that secure the optical drive bracket 1 b Remove the optical drive bracket from the optical drive 2 2 5 Disengage the optical drive bezel tabs to separate the optical drive bezel from the optical drive 6 Remove the optical drive bezel Installing the Optical Drive Engage the optical drive bezel tabs to attach the optical drive bezel to the optical drive Install the optical drive bracket Tighten the screws to secure the optical drive bracket Insert the optical drive into the computer Tighten the screw to secure the optical drive in its place Om gr Se up que opt Install a base cover b battery 7 Follow the procedures in After Working Inside Your Computer 19 Removing the Hard Drive 1 Follow the procedures in Before Working Inside Your Computer 2 Remove a battery b base co
7. LVDS cable from the back of the display panel b Remove the display panel from the display assembly Installing the Display Panel 6 vb WN P Place the display panel to the display assembly Align the display panel in its original position Connect the low voltage differential signaling LVDS cable to the display panel and attach the tape Flip the display panel over and tighten the screws to secure the display panel Install a display bezel b battery Follow the procedures in After Working Inside Your Computer Removing the Camera 1 14 Follow the procedures in Before Working Inside Your Computer Remove a battery b display bezel Perform the following steps a Remove the screw that secures the camera and microphone module b Disconnect the camera cable c Lift and remove the camera and microphone module Installing the Camera 5 PWN bP Place the camera and microphone module on its place Connect the camera cable Tighten the screw to secure the camera and microphone module Install a display bezel b battery Follow the procedures in After Working Inside Your Computer Removing the Keyboard Trim Follow the procedures in Before Working Inside Your Computer Remove the battery Perform the following steps a Pry up the keyboard trim on its sides and the top edge b Lift upwards and remove the keyboard trim from the computer N Installing the Keyboard Trim 1 2
8. Run thorough tests to introduce additional test options to provide extra information about the failed device s e View status messages that inform you if tests are completed successfully e View error messages that inform you of problems encountered during testing FA CAUTION Use the system diagnostics to test only your computer Using this program with other computers may cause invalid results or error messages K NOTE Some tests for specific devices require user interaction Always ensure that you are present at the computer terminal when the diagnostic tests are performed 1 Power on the computer 2 As the computer boots press the lt F12 gt key as the Dell logo appears 3 On the boot menu screen select the Diagnostics option The Enhanced Pre boot System Assessment window is displayed listing all devices detected in the computer The diagnostics starts running the tests on all the detected devices 4 If you wish to run a diagnostic test on a specific device press Esc and click Yes to stop the diagnostic test 5 Select the device from the left pane and click Run Tests 6 If there are any issues error codes are displayed Note the error code and contact Dell 57 Device Status Lights Icon Description Q Turns on when you turn on the computer and blinks when the computer is in a power management mode 98 Turns on when the computer reads or writes data Turns on steadily or blinks to indicate battery charge stat
9. SD card battery base cover keyboard trim e keyboard f display hinge g palmrest 3 Disconnect and remove WLAN cable from its routing channels 4 Perform the following steps a Remove the screws that secure the display cable connector and remove it from the system board b Disconnect the display cables from the system board 5 Remove the screws that secure the display assembly in place and lift to remove the display assembly from the computer 27 NOTE The above display assembly removal procedures are applicable for both Touch and Non touch versions of the computer Installing the Display Assembly Tighten the screws that secure the display assembly in place Insert the WLAN cable through the holes on the chassis Route the display cable along its compartment and connect the display cables to its connectors on the system board Connect the WLAN cables to their connectors 5 Install a palmrest b display hinge c keyboard d keyboard trim e base cover f battery g SDcard 6 Follow the procedures in After Working Inside Your Computer Removing the ExpressCard Cage Follow the procedures in Before Working Inside Your Computer 2 Remove a b c d e 28 SD card battery base cover keyboard trim keyboard f display hinge g palmrest 3 Perform the following steps a Remove the screws that secure the ExpressCard cage b Lift and remove the ExpressCard cage
10. Support Feature Specification No mSATA support on both Latitude E5440 and Latitude with Express Card I O and Discrete Graphic Configuration for other configurations E5540 mSATA is supported on both Latitude E5440 and Latitude E5540 59 Feature without Express Card I O on Discrete Graphic and all UMA Graphic Configurations Table 18 Audio Feature Type Controller Stereo conversion Interface Internal External Speakers Internal speaker amplifier Volume controls Table 19 Video Feature Type Controller UMA Discrete Table 20 Communications Feature Network adapter Wireless Table 21 Ports and Connectors Feature Audio optional Video 60 Specification e Supports mSATA and WWAN on Latitude E5440 e Supports mSATA on Latitude E5540 Specification four channel high definition audio Realtek ALC3226 24 bit analog to digital and digital to analog high definition audio microphone in stereo headphones external speakers connector two 1W RMS per channel hot keys for volume control and mute control Specification integrated on system board Intel HD Graphics 4600 Nvidia GeForce N14M GE Discrete Graphics Card 2 GB Graphics Specification 10 100 1000 Mb s Ethernet RJ 45 e Internal wireless local area network WLAN e Wireless wide area network WWAN E5440 only Specification one microphone stereo headphone speakers connector e one 15 pin VGA con
11. can e Change the NVRAM settings after you add or remove hardware e View the system hardware configuration e Enable or disable integrated devices e Set performance and power management thresholds e Manage your computer security Boot Sequence Boot Sequence allows you to bypass the System Setup defined boot device order and boot directly to a specific device for example optical drive or hard drive During the Power on Self Test POST when the Dell logo appears you can e Access System Setup by pressing F2 key e Bring up the one time boot menu by pressing F12 key The one time boot menu displays the devices that you can boot from including the diagnostic option The boot menu options are e Removable Drive if available e STXXXX Drive K NOTE XXX denotes the SATA drive number e Optical Drive e Diagnostics K NOTE Choosing Diagnostics will display the ePSA diagnostics screen The boot sequence screen also displays the option to access the System Setup screen Navigation Keys The following table displays the system setup navigation keys NOTE For most of the system setup options changes that you make are recorded but do not take effect until you re start the system 43 Table 1 Navigation Keys Keys Up arrow Down arrow lt Enter gt Spacebar lt Tab gt lt Esc gt F1 Navigation Moves to the previous field Moves to the next field Allows you to select a value in the se
12. e AHCI e RAID On This option is enabled by default Allows you to configure the SATA drives on board All drives are enabled by default The options are e SATA 0 45 Option SMART Reporting USB Configuration Audio Keyboard Illumination Unobtrusive Mode Miscellaneous Devices 46 Description e SATA 1 e SATA 2 e SATA 3 This field controls whether hard drive errors for integrated drives are reported during system startup This technology is part of the SMART Self Monitoring Analysis and Reporting Technology specification This option is disabled by default e Enable SMART Reporting This field configures the integrated USB controller If Boot Support is enabled the system is allowed to boot any type of USB Mass Storage Devices HDD memory key floppy If USB port is enabled device attached to this port is enabled and available for OS If USB port is disabled the OS cannot see any device attached to this port e Enable Boot Support e Enable External USB Port e Enable USB3 0 Controller NOTE USB keyboard and mouse always work in the BIOS setup irrespective of these settings This field enables or disables the integrated audio controller By default the Enable Audio option is selected This field lets you choose the operating mode of the keyboard illumination feature The keyboard brightness level can be set from 25 to 100 e Disabled e Level is 25 e Level is 50 e Level is 75 e
13. ez dre heaves 58 Battery Stat s Eights eden Dee 58 5 SPECIRICAU OMS ARE LM ES 59 6 Contacting Dell ieu deo oio e t ie ob i Edi DP rz as 65 Working on Your Computer Before Working Inside Your Computer Use the following safety guidelines to help protect your computer from potential damage and to help to ensure your personal safety Unless otherwise noted each procedure included in this document assumes that the following conditions exist AN A gt Ea You have read the safety information that shipped with your computer A component can be replaced or if purchased separately installed by performing the removal procedure in reverse order WARNING Before working inside your computer read the safety information that shipped with your computer For additional safety best practices information see the Regulatory Compliance Homepage at www dell com regulatory compliance CAUTION Many repairs may only be done by a certified service technician You should only perform troubleshooting and simple repairs as authorized in your product documentation or as directed by the online or telephone service and support team Damage due to servicing that is not authorized by Dell is not covered by your warranty Read and follow the safety instructions that came with the product CAUTION To avoid electrostatic discharge ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface such as a
14. from the computer Installing the ExpressCard Cage Align the ExpressCard cage to its original position on the computer and snap it into place Install the screws that secure the ExpressCard cage to the system board Install a palmrest b display hinge c keyboard d keyboard trim e base cover f battery g SD card 4 Follow the procedures in After Working Inside Your Computer Removing the System Fan Follow the procedures in Before Working Inside Your Computer 2 Remove a SD card b battery C base cover d keyboard trim e keyboard f memory g optical drive h hard drive i display hinge j palmrest 29 3 Disconnect a system fan cable b I O board cable 4 Remove the screws that secure the system fan and lift the system fan to remove from the computer Q Installing the System Fan Place the system fan on the computer Connect the system fan cable to the system board Connect the I O board cable to its connector Tighten the screws to secure the system fan on the computer SB wort Install a palmrest b display hinge c memory d hard drive e optical drive 30 6 f keyboard g keyboard trim h base cover i battery j SD card Follow the procedures in After Working Inside Your Computer Removing the System Board 1 2 Follow the procedures in Before Working Inside Your Computer Remove a SD card b battery c base cover d k
15. steps a Remove the power connector cable from the routing channels b Lift and remove the power connector from the computer Seed Installing the Power Connector 1 4 Place the power connector on its place in the computer Route the power connector cable on its routing channels Install a system board b system fan c ExpressCard cage d palmrest e display hinge f WLAN card g hard drive h optical drive i memory j keyboard k keyboard trim I base cover m battery n SD card Follow the procedures in After Working Inside Your Computer Removing the Speakers 1 38 Follow the procedures in Before Working Inside Your Computer Remove a SD memory card b battery C base cover d keyboard trim e keyboard f memory g optical drive h hard drive i WLAN card j display hinge k palmrest l system fan m ExpressCard cage n system board 3 Perform the following steps a Remove the speaker cable from the routing channels b Remove the screws that secure the speakers from the computer c Lift and remove the speakers from the computer AA Installing the Speakers Place the speakers on the computer Secure the speaker cable to the routing channels Tighten the screws to secure the speakers to the computer Bow OM Install a system board b ExpressCard cage C system fan d palmrest e display hinge f WLAN card g hard drive h optical dri
16. Allows you to set or change the system s internal hard disk drive K NOTE Successful password changes take effect immediately Default Setting Not set Allows you to enforce the option to always set strong passwords Default Setting Enable Strong Password is not selected NOTE If Strong Password is enabled Admin and System passwords must contain at least one uppercase character one lowercase character and be at least 8 characters long Allows you to determine the minimum and maximum length of Administrator and System passwords Allows you to enable or disable the permission to bypass the System and the Internal HDD password when they are set The options are e Disabled e Reboot bypass Default Setting Disabled 47 Option Password Change Non Admin Setup Changes TPM Security Computrace CPU XD Support OROM Keyboard Access Admin Setup Lockout Table 6 Secure Boot Option Secure Boot Enable Expert Key Management 48 Description Allows you to enable the disable permission to the System and Hard Drive passwords when the admin password is set Default Setting Allow Non Admin Password Changes is selected Allows you to determine whether changes to the setup options are allowed when an Administrator Password is set If disabled the setup options are locked by the admin password Allows you to enable the Trusted Platform Module TPM during POST Default Setting The option is disabled Allows you
17. Dell Latitude E5440 Owner s Manual Regulatory Model P44G Regulatory Type P44G001 Notes Cautions and Warnings K NOTE A NOTE indicates important information that helps you make better use of your computer AN CAUTION A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem A WARNING A WARNING indicates a potential for property damage personal injury or death 2013 Dell Inc All Rights Reserved Trademarks used in this text Dell the Dell logo Dell Boomi Dell Precision OptiPlex Latitude PowerEdge PowerVault PowerConnect OpenManage EqualLogic Compellent KACE FlexAddress Force10 Venue and Vostro are trademarks of Dell Inc Intel Pentium Xeon Core and Celeron are registered trademarks of Intel Corporation in the U S and other countries AMD is a registered trademark and AMD Opteron AMD Phenom and AMD Sempron are trademarks of Advanced Micro Devices Inc Microsoft Windows Windows Server Internet Explorer MS DOS Windows Vista and Active Directory are either trademarks or registered trademarks of Microsoft Corporation in the United States and or other countries Red Hat and Red Hat Enterprise Linux are registered trademarks of Red Hat Inc in the United States and or other countries Novell and SUSE are registered trademarks of Novell Inc in the United States and ot
18. Level is 100 This option is enabled by default This option when enabled pressing Fn B turns of all light and sound emissions in the system To resume normal operation press Fn B again This option is Disabled by default Allows you to enable or disable the following devices e Enable Microphone e Enable Camera e Enable Express card e Enable Hard Drive Free Fall Protection e Enable Media Card e Disable Media Card Option Table 4 Video Option LCD Brightness Description K NOTE All devices are enabled by default You can also enable or disable Media Card Description Allows you to set the display brightness depending up on the power source On Battery and On AC K NOTE The Video setting will only be visible when a video card is installed into the system Table 5 Security Option Admin Password System Password Internal HDD 1 Password Strong Password Password Configuration Password Bypass Description Allows you to set change or delete the administrator admin password NOTE You must set the admin password before you set the system or hard drive password Deleting the admin password automatically deletes the system password and the hard drive password K NOTE Successful password changes take effect immediately Default Setting Not set Allows you to set change or delete the system password K NOTE Successful password changes take effect immediately Default Setting Not set
19. an nar i ed 26 Removing the Display ASSEMDLY ccscccsscsssecssecseeesseesseeeseecsescseecsueceseeeseeesesesseseeeceseeeaeesseesseesees 26 Installing the Display ASSEMDILY cc ccscccssccssscssecssecssesesssesseessecseecsaecseceseecseecsescsaeecsesestecsesesesses 28 Removing the Expresscard C ge edes ed De HE een db ebd dies 28 Installing the ExpressCard Cage ccccccsccceseceseceeeeeeeecececeeeceaeeeaeeeaeecaeeeaaeceaeseaeseaeeeaeeeeaeseeeeeeeseeesaees 29 Removing the System Fan 5 eventos ideas e o e C RR EG en RW REESE EE vient 29 Installing the System Fan ooo tte dece geek eredi Hottie cae tu toto HER ep E Ee e ce 30 Removing the System Board esssssseseieseeeee ee ennne nennen nnn nennen entre nennen rennen nns 31 Installing the System Board iere I E rri ah a E ER UE ETC Deme E Cina 33 Removing the Heatsink 1 retenti tenerte thus ne ire Fa ER epa Rh eura Raten nae xu Ra Erb ua Ea nun dus 34 Installing the Heatsinks nganana tanneries vu radere ere he raaraa nda eod Eee Ea rade ge TOR Ira 34 Removing the I O Board Left eesssssseesesseseseseeee eene nennen nennen nennen nennen nnns 35 Installing the I O Board Left einst irent ceste eerte cade e neon dede en 36 Removing the I O Board RiQht cc ccssceseceeeeeeeeeeeneeeaeeeaeesaeecneeaaeseaeeeaeesaeesaeesaeseaeeeaeeseeseaeeaaes 36 Installing the I O Board Right nenn
20. appears 11 Click Save to save the file on your computer 12 Click Run to install the updated BIOS settings on your computer Follow the instructions on the screen System and Setup Password You can create a system password and a setup password to secure your computer Password Type Description System password Password that you must enter to log on to your system Setup password Password that you must enter to access and make changes to the BIOS settings of your computer A CAUTION The password features provide a basic level of security for the data on your computer CAUTION Anyone can access the data stored on your computer if it is not locked and left unattended K NOTE Your computer is shipped with the system and setup password feature disabled Assigning a System Password and Setup Password You can assign a new System Password and or Setup Password or change an existing System Password and or Setup Password only when Password Status is Unlocked If the Password Status is Locked you cannot change the System Password 54 NOTE If the password jumper is disabled the existing System Password and Setup Password is deleted and you need not provide the system password to log on to the computer To enter a system setup press lt F2 gt immediately after a power on or re boot 1 Inthe System BIOS or System Setup screen select System Security and press Enter The System Security screen appears 2 Inthe System Securi
21. ard trim e keyboard f memory g optical drive h hard drive i WLAN card j display hinge k palmrest l system fan m ExpressCard cage n system board 3 Perform the following steps a Remove the screws that secure the heatsink in place b Lift to remove the heatsink from the computer Installing the Heatsink Place the heatsink on the system board Tighten the screws to secure the heatsink to the computer 3 Install a system board b ExpressCard cage c system fan 34 4 d palmrest e display hinge f WLAN card 9 hard drive h optical drive i memory j keyboard k keyboard trim l base cover m battery n SD card Follow the procedures in After Working Inside Your Computer Removing the I O Board Left 1 Follow the procedures in Before Working Inside Your Computer Remove a SD card b battery C base cover d keyboard trim e keyboard f memory g optical drive h hard drive i WLAN card j display hinge k palmrest l system fan m ExpressCard cage n system board Perform the following steps a Remove the screw that secures the left O board on the computer b Lift the I O board and remove from the computer 35 Installing the I O Board Left 1 Place the I O board on the computer Tighten the screw to secure the I O board to the computer 3 Install a system board b ExpressCard cage c system fan d palmrest e display hin
22. connector on the back of the computer CAUTION Handle components and cards with care Do not touch the components or contacts on a card Hold a card by its edges or by its metal mounting bracket Hold a component such as a processor by its edges not by its pins CAUTION When you disconnect a cable pull on its connector or on its pull tab not on the cable itself Some cables have connectors with locking tabs if you are disconnecting this type of cable press in on the locking tabs before you disconnect the cable As you pull connectors apart keep them evenly aligned to avoid bending any connector pins Also before you connect a cable ensure that both connectors are correctly oriented and aligned NOTE The color of your computer and certain components may appear differently than shown in this document To avoid damaging your computer perform the following steps before you begin working inside the computer 1 Ensure that your work surface is flat and clean to prevent the computer cover from being scratched Turn off your computer see Turning Off Your Computer If the computer is connected to a docking device docked such as the optional Media Base or Battery Slice undock it CAUTION To disconnect a network cable first unplug the cable from your computer and then unplug the cable from the network device 4 Disconnect all network cables from the computer 5 Disconnect your computer and all attached devices from thei
23. e gene ete Rte ast etas E tes 11 Installing the SD Caid 2 ennt teer a fot Site FERNER Eie 11 Removing the ExpressCard 12 1 10 0 stet ei UR ER E Eee ge edo RE ERR RENE OR ever ge Rd Dern 11 stalling the Express C A nei oat ance ate eR ee hers 12 Removing the SIM Card ceed peo ne eid ude sven de ede nie em eects 12 Installing the SIM Card daaa aaa aa a aa aa a aaO aa aa oaeiae aeaa ala aia 12 Removing the Display B zZel rirse irsi ei aaae bear na a ia aeaa eE nn OEA nnns nns 12 Installing the Display B zel neron a ete eda de E DEBES I ERIT nie 13 Removing the Display PaneL sesssssesseseeseeee nennen nennen nennen nnne nnns nennen resin nnne nnne nnns 13 Installing the Display Panel niece ette toute enn ai nr koe e iad enne a PUn 14 Removing the Camera n etre suds lagi tiere exe Ten ep Lex va ER Hr eeu uz are e WERE aa RETO EN aaa Eee ENTRE 14 Installing the Camera cci ded on HER LED ere aia dra e ve P eed eH eae aL cad data E eda Ya es 15 Removing the Keyboard Trim itti ni rh rocked beers ER Ra EBEN a ERR ER HER En Fue vaa Ran PARAR 15 Installing the Keyboard Trim eseeessssesseeeeee eene nnnm nnne nennen nennen nnne 15 Removing the Key boa d a n ide Ded ea e Acn eedem a a ae 16 Installing the Keyboard sssesessseeeseeeee nennen a nnne nennen ennt a nennt sienne nnns nennen 17 Removing the Base Covers iren retenu c dede dense a esas is eee aee eae ey e PE RR RE SERE ea euh 18 Installing the
24. en nennen nnne tenes nennen nnn 37 Removing the Power Corinector esl Lit d ere tp ei Eia Peer cuss EIER ER Ra ep 37 Installing the Power CONMECtONM ccccceeeeseeeeeeeeneeeeeeseaneeeeeseneeeeeeeaeeeeeeeaeeeeseaneeeeseseeeeeeeseeeeeesaees 38 Removing the Speakers oet iie erede rr Ferd noa Ec ei dre nya koe ERA EROR Vel a a 38 Installing the Speakers dicio etie de t tdt ont deserat Raia aarden ERE n Ede er LSe ERR sets 39 Removing the Status Light Board ssssssssssssssssssseeeeeeeeen nennen nnne nnne nnnm nettes nnne nnn 40 Installing the Status Light BOard cccccccecececeee eee eeeeeee cea aeeeee eee a aeaaea a ia epa eRe Aiae aae 40 SB 5ysteli Setup Greases ones PER d eae pa EEEE E EE seas 43 BOOt SCQUEM CG ROME 43 Navigation Keys nidi rater ln oca e eee xy ove i oa FUE da aah eave E EEEa dance 43 System Setup Options REI E M 44 Updating the BIOS inei dersten a AAEE AAT even uneven Minin natives 54 System and Set p PassWotd 5 nee UE eed aa Neea aae aaa Ee Pe dk drea Ec 54 Assigning a System Password and Setup Password sss 54 Deleting or Changing an Existing System and or Setup Password eese 55 4 DNA INOSE CS m R 57 Enhanced Pre Boot System Assessment ePSA DiagnostiCs ceeeeeesceeeeeeeteneeeeseeeeeneeeesaeeeeaaees 57 Device Status Lights 1 cecinere rac eil ceed ety ee ne Ye dre n dog
25. eyboard trim e keyboard f memory g optical drive h hard drive i WLAN card j display hinge k palmrest l system fan m ExpressCard cage Disconnect a coin cell battery cable b speaker cable Flip the computer and disconnect a power cable b status light board cable c I O board cable 31 32 Perform the following steps a Remove the screws that secure the display cable connector and remove it from the system board b Disconnect the display cables and power connector cable from the system board PN Remove the screws that secure the system board and lift the system board to remove from the computer Installing the System Board 1 Align the system board into its original position on the computer 2 Replace and tighten the screws to secure the system board to the computer 3 Connect the following cables a I O board cable b power connector cable C status light board cable 4 Turn over the computer and connect the coin cell battery cable and speaker cable to the system board 5 Install a ExpressCard cage b system fan C palmrest d display hinge e WLAN card f hard drive g optical drive h memory i keyboard j keyboard trim k base cover l battery m SD card 6 Follow the procedures in After Working Inside Your Computer Removing the Heatsink 1 Follow the procedures in Before Working Inside Your Computer Remove a SD card b battery C base cover d keybo
26. ge f WLAN card g hard drive h optical drive i memory j keyboard k keyboard trim I base cover m battery n SD card 4 Follow the procedures in After Working Inside Your Computer Removing the I O Board Right 1 Follow the procedures in Before Working Inside Your Computer 2 Remove a SD card b battery C base cover d keyboard trim e keyboard f memory g optical drive h hard drive i WLAN card j display hinge k palmrest U system fan m ExpressCard cage n system board 3 Perform the following steps a Remove the screws that secure the I O board on the computer b Lift the I O board and remove from the computer 36 Installing the I O Board Right 1 Place the I O board on the computer 2 Tighten the screws to secure the I O board to the computer 3 Install a system board b ExpressCard cage c system fan d palmrest e display hinge f WLAN card g hard drive h optical drive i memory j keyboard k keyboard trim l base cover m battery n SD card 4 Follow the procedures in After Working Inside Your Computer Removing the Power Connector 1 Follow the procedures in Before Working Inside Your Computer 2 Remove a SD card b battery C base cover d keyboard trim e keyboard f memory g hard drive h optical drive i WLAN card j display hinge k palmrest I ExpressCard cage m system fan n system board Perform the following
27. her countries Oracle is a registered trademark of Oracle Corporation and or its affiliates Citrix Xen XenServer and XenMotion are either registered trademarks or trademarks of Citrix Systems Inc in the United States and or other countries VMware vMotion vCenter vCenter SRM and vSphere are registered trademarks or trademarks of VMware Inc in the United States or other countries IBM is a registered trademark of International Business Machines Corporation 2013 10 Rev A00 Contents 1 Working on Your Compwuter esesesseseeeeee eene nnna nnns nn nnns nina natns sana nina san 5 Before Working Inside Your Computer eessssesssseeeeeeeneeeen nennen nnnm 5 Turning Off Your Combpulter xiii deserun addu era eden nua te a dere aenea ode 6 After Working Inside Your Computer ussssssssssssssssssssesseee eene nenetnnn nnns hn nnt nnn nnn nnntnn nennen 7 2 Removing and Installing COMPONEMNG ccseccssceceseeseeesseeesseeseeeeseeesseesaees 9 Recommended Tools 1 ie Dyer RR HR RP ERA ER RERUM ERI NEM g Minera g ne pat ee Regul 9 Syst m Overview ixi ied ine fin wid don Edere e hee eredi Re le c OH HERR IER Te 9 Remiovirigthe Battery eiecti n me ond tvatectebce ceps anres die atia de epe Rede 10 Installing the Battery ocior eei epus eee eee redeas evene Dre ev aere e du eva E dno be e DU gend gen 11 REMOVING the SD Card d eere ete redu ree b
28. hinge at the front and back of the computer 3 Install a keyboard b keyboard trim c base cover d battery 4 Follow the procedures in After Working Inside Your Computer Removing the Palmrest 1 Follow the procedures in Before Working Inside Your Computer 2 Remove a SD card b battery C base cover d keyboard trim e keyboard f memory g optical drive h hard drive i display hinge 3 Remove the screws at the bottom of the computer 24 4 Disconnect a media buttons cable b touch pad cable c fingerprint scanner cable d power button cable 5 Perform the following steps a Remove the screws that secure the palmrest of the computer b Lift and remove the palmrest from the computer 25 Installing the Palmrest Align the palmrest assembly to its original position in the computer and snap it into place Connect the following cables to the system board a b c d power button cable fingerprint scanner cable touch pad cable media button cable 3 Tighten the screws to secure the palmrest at the front and back of the computer 4 Install a b c d e f g h i display hinge hard drive optical drive memory keyboard keyboard trim base cover battery SD card 5 Follow the procedures in After Working Inside Your Computer Removing the Display Assembly Follow the procedures in Before Working Inside Your Computer Remove a b c d 26
29. ic scribe System Overview Figure 1 Inside View Back 1 hard drive with isolation cap 4 optical drive coin cell battery 5 WLAN card 3 memory module Figure 2 Inside view Front 1 power connector 6 status light board 2 I O board left 7 system board 3 system fan 8 I O board right 4 ExpressCard cage 5 speakers Removing the Battery 1 Follow the procedures in Before Working Inside Your Computer 2 Perform the following steps a Slide the battery release latches into the unlock position b Push and remove the battery from the computer 10 Installing the Battery 1 Slide the battery into its slot until it clicks into place 2 Follow the procedures in After Working Inside Your Computer Removing the SD Card 1 Follow the procedures in Before Working Inside Your Computer 2 Press in on the SD card to release it from the computer 3 Slide the SD card out of the computer oO e A Installing the SD Card 1 Push the SD card into the compartment until it clicks into place 2 Follow the procedures in After Working Inside Your Computer Removing the ExpressCard 1 Follow the procedures in Before Working On Your Computer 2 Perform the following steps a Push in on the ExpressCard to release from the computer 1 b Slide the ExpressCard out of the computer 2 11 Installing the ExpressCard 1 Slide the ExpressCard in its slot until it clicks in place 2 F
30. imensions 62 Specification 360 mm 14 17 inches 394 24 mm 15 60 inches 344 23 mm x 193 54 mm e 1366 x 768 pixels e 1920 x 1080 pixels 220 nits for HD 300 nits for FHD 0 closed to 135 60 Hz e 40 for HD e 60 for FHD e 10 30 for HD e 50 for FHD 0 2265 mm x 0 2265 mm e 0 2520 mm x 0 2520 mm for HD 0 1790 x 0 1790 for FHD Specifcation United States 86 keys United Kingdom 87 keys Brazil 87 keys and Japan 90 keys QWERTY AZERTY Kanji Specification 80 00 mm 3 15 inches 45 00 mm 1 77 inches Specification 4 6 or 9 cell smart lithium ion Feature Height 4 6 and 9 cell Width 4 and 6 cell 9 cell Depth 4 and 6 cell 9 cell Weight 4 cell 6 cell 9 cell Voltage 4 cell 6 and 9 cell Temperature range Operating Non Operating Coin cell battery Table 26 AC Adapter Feature Type Input voltage Input current maximum Input frequency Output power Output current Latitude E5440 65 W 100 VAC to 240 VAC 17A 50 Hz to 60 Hz 65W 3 34 A continuous Specification 20 00 mm 0 79 inch 208 00 mm 8 18 inches 214 00 mm 8 43 inches 48 08 mm 1 89 inches 71 79 mm 2 83 inches 240 00 g 0 53 lb 344 73 g 0 76 lb 508 20 g 1 12 lb 14 8 VDC 11 1 VDC 0 C to 50 C 32 F to 122 F 40 C to 85 C 40 F to 185 F K NOTE The battery pack is capable of safely withstanding the above storage temperatures wi
31. in the lower right corner of the Start menu as shown below and then click 9 a8 Shut Down 2 Ensure that the computer and all attached devices are turned off If your computer and attached devices did not automatically turn off when you shut down your operating system press and hold the power button for about 4 seconds to turn them off After Working Inside Your Computer After you complete any replacement procedure ensure you connect any external devices cards and cables before turning on your computer A CAUTION To avoid damage to the computer use only the battery designed for this particular Dell computer Do not use batteries designed for other Dell computers 1 Connectany external devices such as a port replicator battery slice or media base and replace any cards such as an ExpressCard 2 Connectany telephone or network cables to your computer CAUTION To connect a network cable first plug the cable into the network device and then plug it into the computer 3 Replace the battery 4 Connect your computer and all attached devices to their electrical outlets 5 Turn on your computer Removing and Installing Components This section provides detailed information on how to remove or install the components from your computer Recommended Tools The procedures in this document may require the following tools e Small flat blade screwdriver e 0 Phillips screwdriver e 1 Phillips screwdriver e Small plast
32. lected field if applicable or follow the link in the field Expands or collapses a drop down list if applicable Moves to the next focus area K NOTE For the standard graphics browser only Moves to the previous page till you view the main screen Pressing lt Esc gt in the main screen displays a message that prompts you to save any unsaved changes and restarts the system Displays the System Setup help file System Setup Options NOTE Depending on the computer and its installed devices the items listed in this section may or may not appear Table 2 General Option System Information Battery Information Boot Sequence 44 Description This section lists the primary hardware features of your computer e System Information Displays BIOS Version Service Tag Asset Tag Ownership Tag Ownership Date Manufacture Date and the Express Service Code e Memory Information Displays Memory Installed Memory Available Memory Speed Memory Channels Mode Memory Technology DIMM ASize DIMM B Size e Processor Information Displays Processor Type Core Count Processor ID Current Clock Speed Minimum Clock Speed Maximum Clock Speed Processor L2 Cache Processor L3 Cache HT Capable and 64 Bit Technology e Device Information Displays Primary Hard Drive MiniCard Device ODD Device Dock eSATA Device LOM MAC Address Video Controller Video BIOS Version Video Memory Panel Type Native Resolution Audio Contro
33. ller Wi Fi Device WiGig Device Cellular Device Bluetooth Device Displays the battery status and the type of AC adapter connected to the computer Boot Sequence Allows you to change the order in which the computer attempts to find an operating system The options are Diskette Drive Internal HDD e USB Storage Device e CD DVD CD RW Drive e Onboard NIC Option Advanced Boot Options Date Time Description By default all the options are checked You can also deselect any option or change the boot order Boot List Option Allows you to change the boot list option e Legacy e UEFI This option allows you the legacy option ROMs to load By default the Enable Legacy Option ROMs is unchecked Allows you to change the date and time Table 3 System Configuration Option Integrated NIC Parallel Port Serial Port SATA Operation Drives Description Allows you to configure the integrated network controller The options are e Disabled Enabled e Enabled w PXE This option is enabled by default Allows you to configure the parallel port on the docking station The options are e Disabled e AT This option is enabled by default e PS2 e ECP Allows you to configure the integrated serial port The options are e Disabled e COM1 This option is enabled by default e COM2 e COM3 e COMA Allows you to configure the internal SATA hard drive controller The options are e Disabled
34. nector e 19 pin HDMI connector Feature Network adapter USB 2 0 USB 3 0 Memory card reader Docking port Subscriber Identity Module SIM port Table 22 Display Feature Type Latitude E5440 Latitude E5540 Size Latitude E5440 Latitude E5540 Dimensions Latitude E5440 Height Width Diagonal Active ares X Y Maximum resolution Maximum Brightness Latitude E5540 Height Specification one RJ 45 connector e one 4 pin USB 2 0 compliant connector E5440 e two 4 pin USB 2 0 compliant connectors E5540 K NOTE The USB 2 0 connector at the back of the Latitude E5540 computer gets deactivated when the Latitude E5540 computer is connected to the docking station two USB 3 0 compliant connectors one 8 in 1 memory card reader one one E5440 only Specification e HD 1366x768 WLED e HD 1600 x 900 e HD 1366x768 WLED e FHD 1920 x 1080 14 0 15 6 192 5 mm 7 57 inches 324 mm 12 75 inches 355 60 mm 14 00 inches 309 40 mm x 173 95 mm e 1366 x 768 pixels e 1600 x 900 pixels 200 nits 210 mm 8 26 inches 61 Feature Width Diagonal Active area X Y Maximum resolution Maximum Brightness Operating angle Refresh rate Minimum Viewing angles Horizontal Vertical Pixel pitch Latitude E5440 Latitude E5540 Table 23 Keyboard Feature Number of keys Layout Table 24 Touchpad Feature Active Area X axis Y axis Table 25 Battery Feature Type D
35. nt database from a user selected file e Delete Deletes the selected key e Reset All Keys Resets to default setting e Delete All Keys Deletes all the keys NOTE If you disable the Custom Mode all the changes made will be erased and the keys will restore to default settings Description This field specifies whether the process will have one or all cores enabled The performance of some applications will improve with the additional cores This option is enabled by default Allows you to enable or disable multi core support for the processor The options are All e 1 e 2 Default Setting All Allows you to enable or disable the Intel SpeedStep feature Default Setting Enable Intel SpeedStep Allows you to enable or disable the additional processor sleep states Default Setting The option C states is enabled Allows you to enable or disable the Intel TurboBoost mode of the processor Default Setting Enable Intel TurboBoost Allows you to enable or disable the HyperThreading in the processor Default Setting Enabled This option might improve the battery life by automatically putting the computer in to a low power state during Sleep after a user specified amount of time Default Setting Disabled 49 Table 8 Power Management Option AC Behavior Auto On Time USB Wake Support Wireless Radio Control Wake on LAN WLAN Block Sleep Peak Shift Advanced Battery Charge Configuration 50 Description
36. ollow the procedures in After Working Inside Your Computer Removing the SIM Card Follow the procedures in Before Working On Your Computer Remove the battery Press and release the SIM card located on the battery wall BwuNP Slide the SIM card from the computer K NOTE The SIM slot in the computer supports only micro SIM Installing the SIM Card 1 Insert the SIM card into the slot 2 Install the battery 3 Follow the procedures in After Working Inside Your Computer Removing the Display Bezel 1 Follow the procedures in Before Working Inside Your Computer 2 Remove the battery 3 Perform the following steps a Pry up the bottom edge of the display bezel b Work your way around the sides and top edge of the display bezel 12 4 Remove the display bezel from the computer Installing the Display Bezel 1 2 Place the display bezel onto the display assembly Starting from the top corner press on the display bezel and work around the entire bezel until it snaps onto the display assembly Install the battery Follow the procedures in After Working Inside Your Computer Removing the Display Panel Follow the procedures in Before Working Inside Your Computer Remove a battery b display bezel Remove the screws that secure the display panel and flip the panel over 4 Perform the following steps 13 a Lift the mylar tape and disconnect the low voltage differential signaling
37. ption Displays the Service Tag of your computer Allows you to create a system asset tag if an asset tag is not already set This option is not set by default Description Allows you to view and clear the System Setup BIOS POST events Allows you to view and clear the System Setup Thermal events Allows you to view and clear the System Setup Power events 53 Updating the BIOS It is recommended to update your BIOS system setup on replacing the system board or if an update is available For laptops ensure that your computer battery is fully charged and connected to a power outlet 1 Re start the computer Go to dell com support 3 Enter the Service Tag or Express Service Code and click Submit K NOTE To locate the Service Tag click Where is my Service Tag NOTE If you cannot find your Service Tag click Detect Service Tag Proceed with the instructions on screen If you are unable to locate or find the Service Tag click the Product Category of your computer Choose the Product Type from the list Select your computer model and the Product Support page of your computer appears Click Drivers amp Downloads On the Drivers and Downloads screen under the Operating System drop down list select BIOS Identify the latest BIOS file and click Download File 10 Select your preferred download method in the Please select your download method below window click Download File o0 ONAN SE The File Download window
38. r electrical outlets 6 Close the display and turn the computer upside down on a flat work surface NOTE To avoid damaging the system board you must remove the main battery before you service the computer 7 Remove the main battery 8 Turn the computer top side up 9 Open the display 10 Press the power button to ground the system board A CAUTION To guard against electrical shock always unplug your computer from the electrical outlet before opening the display CAUTION Before touching anything inside your computer ground yourself by touching an unpainted metal surface such as the metal at the back of the computer While you work periodically touch an unpainted metal surface to dissipate static electricity which could harm internal components 11 Remove any installed ExpressCards or Smart Cards from the appropriate slots Turning Off Your Computer CAUTION To avoid losing data save and close all open files and exit all open programs before you turn off your computer 1 Shut down the operating system n Windows 8 Using a touch enabled device a Swipe in from the right edge of the screen opening the Charms menu and select Settings l b Select the O and then select Shut down Using a mouse a Point to upper right corner of the screen and click Settings I b Click the O and select Shut down In Windows 7 1 Click sua 2 Click Shut Down or 1 Click stan 2 Click the arrow
39. rity screen verify that Password Status is Unlocked 3 Select System Password alter or delete the existing system password and press Enter or Tab 4 Select Setup Password alter or delete the existing setup password and press Enter or Tab NOTE If you change the System and or Setup password re enter the new password when promoted If you delete the System and or Setup password confirm the deletion when promoted 5 Press Esc and a message prompts you to save the changes 6 Press Y to save the changes and exit from the System Setup The computer reboots 55 56 4 Diagnostics If you experience a problem with your computer run the ePSA diagnostics before contacting Dell for technical assistance The purpose of running diagnostics is to test your computer s hardware without requiring additional equipment or risking data loss If you are unable to fix the problem yourself service and support personnel can use the diagnostics results to help you solve the problem Enhanced Pre Boot System Assessment ePSA Diagnostics The ePSA diagnostics also known as system diagnostics performs a complete check of your hardware The ePSA is embedded with the BIOS and is launched by the BIOS internally The embedded system diagnostics provides a set of options for particular devices or device groups allowing you to e Run tests automatically or in an interactive mode e Repeat tests e Display or save test results e
40. runs only in battery even if the AC is attached This option enables you to maximize the battery health By enabling this option your system uses the standard charging algorithm and other techniques during the non work hours to improve the battery health Option Primary Battery Charge Configuration Battery Slice Charge Configuration Intel Smart Connect Technology Table 9 POST Behavior Option Adapter Warnings Keypad Embedded Mouse Touchpad Description Disabled default Allows you to select the charging mode for the battery The options are e Adaptive e Standard e ExpressCharge This option is enabled by default e Primarily AC use e Custom If Custom Charge is selected you can also configure Custom Charge Start and Custom Charge Stop NOTE All charging mode may not be available for all the batteries To enable this option disable the Advanced Battery Charge Configuration option Allows you to select the type of charge for the battery The options are e Standard Charge e Express Charge This option is enabled by default NOTE Express charge may not be available for all the batteries To enable this option disable the Advanced Battery Charge Configuration option This option if enabled periodically senses the nearby wireless connections while the system is in sleep state You can use this option to synchronize the email or other social media application that are open when the system enter
41. s the sleep state Description Allows you to enable or disable the system setup BIOS warning messages when you use certain power adapters Default Setting Enable Adapter Warnings Allows you to choose one of two methods to enable the keypad that is embedded in the internal keyboard e Fn Key Only This option is enabled by default e By Numlock NOTE The Keyboard Embedded option is not supported in Latitude E5540 Allows you to define how the system handles mouse and touch pad input The options are e Serial Mouse e PS2 Mouse 51 Option Numlock Enable Fn Key Emulation Mebx Hotkey Fastboot Extended BIOS POST Time Table 10 Virtualization Support Option Virtualization VT for Direct I O Trusted Execution 52 Description e Toushpad PS 2 Mouse This option is enabled by default Allows you to enable the Numlock option when the computer boots Enable Network default Allows you to set the option where the lt Scroll Lock gt key is used to simulate the lt Fn gt key feature Enable Fn Key Emulation default Allows you to specify whether the MEBx Hotkey function should be enabled when the system boots Enable MEBx Hotkey default Allows you to speed up the boot process by bypassing some of the compatibility steps The options are e Minimal e Thorough default e Auto Allows you to create an additional pre boot delay The options are e Oseconds e 5 seconds default e 10 seconds
42. th 100 charge NOTE The battery pack is also capable of withstanding storage temperatures from 20 C to 60 C with no degradation in its performance Ea 3 V CR2032 lithium coin cell Latitude E5540 90 W adapter 100 VAC to 240 VAC 1 5 A 50 Hz to 60 Hz 90 W 4 62 A continuous 63 Feature Rated output voltage Temperature range Operating Non Operating Table 27 Physical Physical Touch Height Front 27 70 mm 1 09 inches Back 32 20 mm 1 27 inches Width Depth Weight 1 99 kg 4 40 lb minimu m Table 28 Environmental Feature Temperature Operating Storage Latitude E5440 19 5 1 0 VDC 0 C to 40 C 32 F to 104 F 40 C to 70 C 40 F to 158 F Latitude E5440 Non touch Front 25 20 mm 0 99 inch Back 28 65 mm 1 13 inches 338 00 mm 13 31 inches 235 00 mm 9 25 inches Specification 0 C to 35 C 40 C to 65 Relative humidity maximum Operating Storage Altitude maximum Operating Non Operating Airborne contaminant level 64 10 to 90 Latitude E5540 19 5 1 0 VDC 0 C to 40 C 32 F to 104 F 40 C to 70 C 40 F to 158 F Latitude E5540 Non touch Front 26 00 mm 1 02 inches Back 33 60 mm Back 29 70 mm 1 32 inches 1 17 inches 379 00 mm 14 92 inches Touch Front 28 25 mm 1 11 inches 250 50 mm 9 86 inches 2 42 kg 5 35 lb 32 F to 95 F
43. to activate or disable the optional Computrace software The options are e Deactivate e Disable e Activate NOTE The Activate and Disable options will permanently activate or disable the feature and no further changes will be allowed Deactivate default Allows you to enable the Execute Disable mode of the processor Enable CPU XD Support default Allows you to set an option to enter the Option ROM Configuration screens using hotkeys during boot The options are e Enable e One Time Enable e Disable Default Setting Enable Allows you to prevent users from entering Setup when an Administrator password is set Default Setting Enable Admin Setup Lockout is not selected Description This option enables or disables the Secure Boot Feature e Disable default e Enable Allows you to manipulate the security key databases only if the system is in Custom Mode The Enable Custom Mode option is disabled by default The options are e PK e KEK e db Option Table 7 Performance Option Multi Core Support Intel SpeedStep C States Control Intel TurboBoost Hyper Thread Control Rapid Start Technology Description e dbx If you enable the Custom Mode the relevant options for PK KEK db and dbx appear The options are e Save to File Saves the key to a user selected file e Replace from File Replaces the current key with a key from a user selected file e Append from File Adds a key to the curre
44. ty screen verify that Password Status is Unlocked 3 Select System Password enter your system password and press Enter or Tab Use the following guidelines to assign the system password A password can have up to 32 characters The password can contain the numbers 0 through 9 Only lower case letters are valid upper case letters are not allowed Only the following special characters are allowed space J 0 C D 9 Q0 C Re enter the system password when prompted 4 Type the system password that you entered earlier and click OK 5 Select Setup Password type your system password and press Enter or Tab A message prompts you to re type the setup password 6 Type the setup password that you entered earlier and click OK 7 Press Esc and a message prompts you to save the changes 8 Press Y to save the changes The computer reboots Deleting or Changing an Existing System and or Setup Password Ensure that the Password Status is Unlocked in the System Setup before attempting to delete or change the existing System and or Setup password You cannot delete or change an existing System or Setup password if the Password Status is Locked To enter the System Setup press F2 immediately after a power on or reboot 1 Inthe System BIOS or System Setup screen select System Security and press Enter The System Security screen is displayed 2 Inthe System Secu
45. us o Turns on when wireless networking is enabled Battery Status Lights If the computer is connected to an electrical outlet the battery light operates as follows Alternately blinking amber light and white light Alternately blinking amber light with steady white light Constantly blinking amber light Light off White light on 58 An unauthenticated or unsupported non Dell AC adapter is attached to your laptop Temporary battery failure with AC adapter present Fatal battery failure with AC adapter present Battery in full charge mode with AC adapter present Battery in charge mode with AC adapter present Specifications 5 K NOTE Offerings may vary by region For more information regarding the configuration of your computer click Start Start icon Help and Support and then select the option to view information about your computer Table 14 System Information Feature Specification DRAM bus width Flash EPROM PCle Gen1 bus External Bus Frequency Table 15 Processor Feature 64 bit SPI 32Mbits 64Mbits 100 MHz DMI 5GT s Specification Types L3 cache Table 16 Memory Feature e Intel Core i3 series e Intel Core i5 series e Intel Core i7 series up to 8 MB Specification two SoDIMM slots Memory connector Memory capacity Memory type Minimum memory Maximum memory 2 GB 4 GB or 8 GB DDR3 SDRAM 1600 Mhz 2 GB 8 GB Table 17 mSATA
46. ve i memory j keyboard k keyboard trim I base cover m battery n SD card 5 Follow the procedures in After Working Inside Your Computer Removing the Status Light Board 1 Follow the procedures in Before Working Inside Your Computer Remove a SD card b battery C base cover d keyboard trim e keyboard f memory g optical drive h hard drive i WLAN card j display hinge k palmrest l system fan m ExpressCard cage n system board O speakers 3 Perform the following steps a Remove the LED cover b Disconnect the status light board cable and remove the screw that secures the status light board c Lift and remove the status light board from the computer e Installing the Status Light Board Place the status light board on its place on the computer Connect the status light board cable to its connector Tighten the screw to secure the status light board on the computer PWN Place the LED cover on the status light board Install a b c d e f g h i j k speakers system board system fan ExpressCard cage palmrest display hinge WLAN card hard drive optical drive memory keyboard keyboard trim m base cover n o battery SD card Follow the procedures in After Working Inside Your Computer 41 42 5 System Setup System Setup enables you to manage your computer hardware and specify BIOS level options From the System Setup you
47. ver 3 Perform the following steps a Remove the screws that secure the hard drive bracket in place b Slide and pull the hard drive to remove from its connectors 4 Remove the hard drive isolation cap from the hard drive Installing the Hard Drive 1 Engage the hard drive isolation cap to the hard drive 20 5 Place the hard drive on its connector Place the hard drive bracket on the hard drive and tighten the screws to secure the hard drive bracket in place Install a base cover b battery Follow the procedures in After Working Inside Your Computer Removing the Memory Module Follow the procedures in Before Working Inside Your Computer Remove a battery b base cover Pry the retention clips away from the memory module until it pops up Lift up the memory module and remove it from the computer O xR we 4 Installing the Memory Module 1 Insert the memory into the memory socket Press the clips to secure the memory module to the system board Install a base cover b battery 21 4 Follow the procedures in After Working Inside Your Computer Removing the WLAN Card 1 Follow the procedures in Before Working Inside Your Computer Remove a battery b base cover Perform the following steps a Disconnect the antennae cables from the WLAN card b Remove the screw that secures the WLAN card to the computer c Remove the WLAN card from its slot on the s
48. ystem board Installing the WLAN Card PWN Pp 5 Insert the WLAN card into its connector on the system board Connect the antenna cables to the respective connectors marked on the WLAN card Tighten the screw to secure the WLAN card to the computer Install a base cover b battery Follow the procedures in After Working Inside Your Computer Removing the Coin Cell Battery 22 Follow the procedures in Before Working Inside Your Computer Remove a battery b base cover Perform the following steps a Disconnect the coin cell battery cable from the system board b Pry and remove the coin cell battery from the adhesive Installing the Coin Cell Battery 1 Place the coin cell battery on the system board with adhesive side downwards Connect the coin cell battery cable to the system board 3 Install a base cover b battery 4 Follow the procedures in After Working Inside Your Computer Removing the Display Hinge 1 Follow the procedures in Before Working Inside Your Computer 2 Remove a battery b base cover c keyboard trim d keyboard 3 Remove the screws that secure the display hinge at the back of the computer aw 4 Remove the screws that secure the display hinge at the front of the computer Press and remove the display hinge from the computer 23 Installing the Display Hinge 1 Place the display hinge on the computer N Tighten the screws to secure the display
Download Pdf Manuals
Related Search