SYBA SY-PEX40016
Contents
1. Adapter SATA Perisi vith RAIDS e SATA Ports without RAID Hardware Installation 1 Turn Off the power to your computer and any other connected peripheral devices 2 Unplug the power cord from the back of the computer 3 Remove your computer s cover 4 Remove the slot bracket from an available PCI Express slot 5 To install the card carefully align the card s bus connector with the selected PCI Express slot on the motherboard Push the board down firmly but gently until it is well seated 6 Replace the slot bracket s holding screw to secure the card Jump setting RAID Setting 1 Clear old RAID before set up new RAID set up Jump JP into H H H 2 Keep pressing button TES1 and start the computer restart the computer until buzzer rings Bi Bi Bi 3 For any RAID mode please refer to the information in above table and set up JP15 4 Repeat Step 2 to finish the RAID operation 5 All RAID settings can be done by software JMicron HW RAID Manager under the running of Operation System2. Driver Installation R1 17 48 10_eSATA setup exe windows 2000 XP Vista instal program AP_V0 09 43 setup exe windows 2000 XP Vista AP program 1 Click the setup exe file to install the application of RAID Manager and driver 2 Click the Next button 3 Click the NEXT button to install a different folder by press the Browse button the button of Disk Cost provides the disk space for user choice 4 Click the Next button to confirm the installation 5 Click the Close button it has been successfully installed 6 Restart system To Verify Driver Installation 1 Right click My Computer and click Manage 2 Select Device Manager 3 Look for the following Windows 2000 XP 2003 Double click SCSI and RAID Controller JMicron Serial ATA Gen 2 PCI Express Adapter should be displayed Windows Vista Double click Storage controllers JMicron Serial ATA Gen 2 PCI Express Adapter should be displayed Features PCI Express Interface Compliant with PCI Express Specification Revision 1 0a 1 Lane x1 PCI Express with transfer rate 2 5 Gb s Full Duplex channe SATA II Interface Supports 6 port 3 0Gbps SATA II interface Supports SATA II Gen2i and Gen2m External SATA Connection e SATA Output swing control and automatic impedance calibration for SATA II PHY Supports asynchronous signal recovery Supports partial slumber power saving mode Automatically speed negotiation for 3Gbps or 1 5Gb
3. ps Supports BIST and loopback mode Supports staggered spin up Supports 48 bit LBA addressing Supports ATAPI drives Supports Native Command Queue NCQ Supports Asynchronous Notification Supports PM aware and non PM aware host RAID Function Fully hardware accelerated RAID Engine No external DRAM or processor required for RAID operation Independent of SATA device connection sequence Supports RAID levels 0 1 3 5 10 JBOD CLONE RAID 3 5 write back cache to enhance performance SATA In band application interface Supports more than 2Tera Bytes RAID drive Supports on line command based bad sector recovery Supports on line Auto Rebuild Rebuild speed 200GB hour Rebuild proceed continuously between power cycling Supports Hot Spare on RAID Supports various RAID configuration and monitoring method Connectors 5 x internal SATA connectors 1 x external eSATA connector System Requirements PCl Express enabled system with one available PCI Express slot Driver supported Windows 2000 XP Vista Linux Unix Solaris10 Mac OS X 10 4 3 Oe 1 Port e SATA w o RAID amp 5 Port SATA II w RAID PCT Express e SATAA SATAITRAID Controller Card Package Contents 1 x PCle SATAI 300 4 Channel Adapter 1 x Driver CD 1 x User s Manual 2 x SATA Data Cable Optional Accessories 1 x e SATA Power Cable Hardware Description Note There are 5 SATA ports and 1 e SATA prot in PCle SATA I
Download Pdf Manuals
Related Search