Pyle PMX830I DJ mixer
Contents
1. PYLE www pyleaudio com USER MANUNAL oO OO onion ty HEBBEN ty OB 28 8 88 8 Boe SAR erect TREBLE I COQO8 0980 x lE osos eux 8 98 CORN 5 SESE SSSR JOE wrescY Theme PMX401 PMX630I PMX830I PROFESSIONAL MIXER 4 6 8 Channel balanced microphone and line inputs Treble bass reverb level control on each channel Support USB SD memory card MP3 WMA music format player Return CD TAPE input Send earphones REC output 5 band graphic Equalizer Visit us Pyleaudio com IMPORTANT SAFETY SYMBOLS C AUTION The symbol is used to indicate that some hazardous live terminals are involved AN within this apparatus even under the normal operating conditions which may be sufficient to constitute the risk of electric shock or death N The symbol is used in the service documentation to indicate that specific D component shall be biais by the component specified in that Protected grounding insala Alternating current voltage Hazardous live terminal ON Denotes the apparatus is turned on OFF Denotes the apparatus is turned off WARNING Describes Qaem that should be obs o2. product and possibly the user Unplug this apparatus during lightning storms or when unused for long periods of time Fuse To prevent the risk of fire and damaging the unit please use only of the recommended fuse type as described in the manual Before replacing the fuse make sure the unit turned isconnected from the AC outlet Electrical Connection Improper electrical wiring may invalidate the product warranty Cleaning Clean only with a dry cloth Do not use any solvents such as benzyl or alcohol Servicing Do not implement any servicing other than those means described in the manual Refer all servicing to qualified service personnel only Only use accessories attachments or parts recommended by the manufacturer Warning Please remember the high sound pressure do not only temporarily damage your sense of hearing but can also cause permanent damage Be careful to select a suitable volume EP CAUTION We should like to draw your attention to the fact that extreme volumes may damage your hearing and or your headphones or loudspeakers Turn the MAIN MIX control and phones control in the main section fully down before you switch on the unit Always be careful to set appropriate volume levels 1 CONTROL ELEMENTS AND CONNECTORS 1 FRONT PANEL 1 3 Pin Low impedance Microphone input This input is for balanced low Is always on and available It has an input impendance of 1K ohm The connector Is wire
3. 124dB of boost or cut 9 This is a switch power switch control of the machine on or off will this machine start you will see the blue LED indicator emit light 10 Power LED Indicator 11 3 5mm input jack for use with person 12 Volume control for USB SD gt Please do not connect microphones to the mixer or the stage box or wall box as long as the phantom power supply in switched on Connect the micro Phones before you switch on the power supply IN addition the monitor PA loudspeakers should be muted before you activate the phantom power supply After switching on wait approx One minute in order to allow system stabilization 13 Master Volume This controls the overall volume level of the entire amplifier Typical operation is between 4 and 8 14 Tape Volume this controls the level of the playback inputs RCA jack on rear Panel NUILLA Il ut tll Ml H o ce m p 15 Oo 15 AC Cable this is a standard cable for use with standard voltages from A C Wall Outlets It is grounded and should NEVER have the ground pin removed for any Reason 16 Speaker output each channel impedance is 8 Ohm 17 RETURN These 1 4 jack are for brining in a effects return effect or other Line level source the impedance is 10K ohms 10dBv 18 SEND Out this is a 1 4 2 conductor line output The impedance is 1k ohm 10dB t is used to connect the either additional power or as an additional Recording
4. d as Pin 1 shield Pin 3tnegative cold 2 1 4 Line High Impedance balanced input this may be used as either a high Impedance microphone input or a line level device such as tape players CD Player Returns or radios It will also allow connection from an electric guitar Bass or keyboard It is a 2 conductor input with an impedance of 10k ohms Both the high and low impedance input may be used simultaneously 3 Gain this is the volume control for each channel It sends the Signal to the master mix buss Typical operation is between 4 and 8 dependent the device s on that channel please remember that it acts like a pre amp So if you are using a device that has a volume output control i e a tape or CD Player you will need to do some level matching by adjusting the level controls on Each unit 4 EQ Control This is to adjust the overall tone of the individual inputs It is set at GOHz IOk Hz Since it is a cut or boost control 15dB it will add or Diminish the sound quality 5 EFFX Control this is a send control to the reverb buss It controls the amount of 6 USB SD player this is a support USB SD memory card MP3 WMA music format player By USB SD to control the volume typical operation is between 4 and 8 T Master EFFX This controls the level of echo and time of internal reverberation Back to the mix 8 Master EQ This controls the overall amount of EQ frequencies 63 250 1K 4k 12k Hz This control allows
5. device This line level signal is a mirror image of the mail outputs 19 Tape play L R These RCA jacks are for brining in a deck CD play or other line Level source The impedance is 10K ohm 10qB 20 Tape Record L R These RCA jack are for hooking up a tape desk to record from The mixer Both channels are summed into mono for compatibility The signals are Taken pre master section meaning that they are without reverb or the master tone Section and does not include the tape in signal the impedance is 1k ohm amp 10gB 2 INSTALLTION 2 Main C onnection AC POWER Connect the power supply to the 3 pin mains connector on the rear of the console Use the AC adapter supplied to connect the console to the mains The adapter complies with all applicable safety standards Please use only the power supply unit provided with the console 7 Never connect the ME to the power supply unit while the latter is powered First connect the console to the power supply unit and then connect the power supply unit to the mains 2 2Audio connections You will need a larger number of cables for the various connections to and from the console Please see the illustrations shown below Be sure to use only high grade Please use commercial RCA cables to wire the 2 track inputs and outputs You can of course also connect unbalanced devices to the balanced input outputs Use either mono plugs or ensure that ring and sleeve are bridged in
6. f injury or death to operator CAUTION Describes precautions that should be observed to prevent danger of the apparatus ved to prevent the danger IMPORTANT SAFETY INSTRUCTIONS Read these instructions Keep these instructions Heed all warning Follow all instructions Water amp Moisture Water amp Moisture This Unit should be protected from moisture and rain can not be used near water for example near bathtubs kitchen sinks or a swimming pools etc Heat This unit should be located away from the heat source such as radiators stoves or other appliances that produce heat Ventilation Do not block areas of ventilation opening Failure to do could result in fire Always install accordance with the manufacturer s instructions Power Cord and Plug Protect the power cord from being walked on or pinched sini at especially receptacles and the point where they exit from the apparatus the safety purpose of the polarized or grounding type plug A polation plug hace two blades with one wider than the other A grounding type plug has two blades and a third pane ms The wide blade or the third prong is provided for your safety If the provided plug does not fit into your outlet refer to electrician for replacement Power Supply The apparatus should be connected to the power supply only of the type as marked on the apparatus or described in the manual Failure to do could result in damage to the
7. nge High 10K 15dB Low 060K 15dB 15dB Frequency Hz control range 60 12dB 250 12dB 1K 12dB 4K 12dB 12K 12dB Effects Loop Effects send Type 1 4 TS connector unbalanced Impedance approx 1k ohm Max Output level 10dBv Effects return Type 1 4 TSconnector unbalanced Impedance approx 10Kohm Max Output level 10dBv Control room outputs Type RCA unbalanced Impedance approx 1k ohm output level 10dBv Headphones output Type 1 4 TRS connector Stereo Max Output level 19 dBu 1500 25 dBu you can connect two or a 8 Ohm speakers or a 4Ohm speakers but did not allow S connect two 4Ohm horns Protection Circuit Power on Mute 2 seconds
8. side the stereo plug or pins 1 amp 3 in the case of XLR connectors CF Caution Never use unbalanced XLR connectors PIN and 3 connected on the MIC input connectors when using the phantom power supply Balanced use with XLR connectors I 2groud shield 2 hot ve 3 cold ve Output Input For unbalanced use pin 1 and pin 3 have to be bridged Unbalanced use of 1 4 TRS connector strain relief clamp sleeve Balanced use of 1 4 TRS connector strain relief clamp sleeve Headphones connection with 1 4 TRS connector strain relief clamp 3 SPECIFICATIONS Mono inputs Microphoneinputs XENYX Mic Preamp Type MicE N 20Hz 20 kHz 0 Qsource resistance 50 Q source resistance 150 Q source resistance Frequency response Gain range Max Input level Impedance Signal to noise ratio Distortion THD N Line input XLR electronically balanced discrete input circuit 134 dB 135 7 dB A weighted 131 dB 133 3 dB A weighted 129 dB 130 5 dB A weighted 10 Hz 150 kHz 1 dB 10 Hz 200 kHz 3 dB 10 to 60 dB 12 dBu 10 dB gain approx 2 6 KO balanced 110dB 112 dBA weighted 0 dBu In 22 dB gain 0 005 0 004 A weighted Type 14 TRS connector Electronically balanced Impedance approx 20 2 balanced 10kO unbalanced Gain range 10 to 40 dB Max Input level 22 dBu 0 dB Gain Channel Equalization Frequency Hz control ra
Download Pdf Manuals
Related Search