Harman/Kardon ONYX
Contents
1. button to increase the volume Bluetooth This button helps you pair your system with other devices The system enters into Bluetooth pairing mode automatically when it is turned on for the first time If you want to switch to different wireless connection when you are already connected to a source press and hold the Bluetooth button for more than 4 seconds to put the speaker into pairing mode again NOTE The speakers Bluetooth device name is HK Onyx BT and password is 0000 Wi Fi This button is used to connect your HK Onyx to your Wi Fi network The use of the button depends on the set up method of your system Battery Level Indicator This LED on HK Onyx indicates the status of the battery Onyx Rear Panel Connections and Controls The connections and controls on the rear panel of the HK Onyx are 1 USB Port For charging and Wi Fi setup with iOS devices 2 Power DC input 3 Auxinput 4 WPS USB Port Charger The USB charger port can be used to charge most of the devices when the HK Onyx is connected to the AC adapter in Operational Sleep or OFF modes Power DC Input Connect the AC power adapter to this port to charge the inbuilt battery Aux Input The speaker includes a 3 5 mm stereo mini analog auxiliary input The system automatically detects an audio signal from the auxiliary input WPS The Wi Fi Protected Setup WPS helps your device establish a secure wireless network easily to any WPS enabled router Speaker P2. wm Bluetooth LED White Constant Bluetooth connected White Slow Flash No Bluetooth device connected White Constant Last one Slow Flash Charging per battery levels Grouped LEDs Battery level or volume level White Left to Right Rolling Upgrading Charge complete or no charge All LEDs White Constant for 2 seconds Power ON OFF White Regular Flash Upgrade Failed Volume LED White Constant for 5 seconds Volume change or volume slider button is touched Onyx Troubleshooting Troubleshooting If your Harman Kardon Onyx is not performing the way you think it should check if the problem is covered in this section before calling your dealer or contacting a Harman Kardon Problems Solutions O representative There is no sound coming from the HK Onyx Distortion static crackling or hissing sounds HK onyx emits a loud hum or buzzing noise HK Onyx unit is not charging No power to unit Make sure that the wall outlet or power strip has power Make sure that all switches for outlet power strip are ON and that all switches for the unit are ON If you have not plugged it to the AC source make sure that the battery is charged Audio source or source material may be the problem Test the HK Onyx with another source Volume level may be too high from auxiliary device output Check the volume of the source and turn it down if necessary Input cable is not plugged in properly Check the
3. W O gt 3s TA B wOls Power Button This button when pressed turns the HK Onyx ON or OFF and has an LED to indicate the power mode The three power modes are Operational mode Sleep mode OFF mode When the system is in OFF mode Power LED is not lit touch the power button for more than 2 seconds to switch on the system The power LED turns white when the system is turned on While the unit is powered on touch the power button for at least one second to check the battery status The 5 volume LEDs will light up to show the battery status One LED lit indicates 20 battery life two LEDs indicate 40 battery life and so on When all 5 LEDs are lit the internal battery is fully charged To turn the speaker off touch the Power button for more than 2 seconds The speaker will go into power saving mode automatically after 10 minutes if no music stream is detected The power LED will turn amber and all other LEDs will be turned off To turn the speaker on press the power button for more than 2 seconds Onyx NOTE When the system gets into Operational mode either from the Sleep Standby mode or OFF mode the last used settings will be restored volume source Wi Fi settings volume source Wi Fi settings Volume Controls These touch sensitive buttons control the volume of the unit These buttons are touch sensitive A gentle finger touch can increase or decrease the volume Press the button to decrease the volume Press the
4. input cable connection Cable may have problems Replace the cable It might happen due to ground loop an unsuitable connection Turn the HK Onyx OFF and connect it to another wall outlet No power to unit Make sure that your wall outlet or power strip has power Make sure that all switches for outlet power strip are ON and that all switches for the unit are ON Onyx Specifications Frequency Range Frequency Response No of channels Transducers Bi amplification Maximum SPL Power Requirement Power adaptor Built in Battery Power consumption Speaker impedance Transmitter power Modulation Wireless Dimensions Dia x W x H 2402MHz 2480MHz 60Hz 20kHz 4 2 X 3 woofers 2 X 34 tweeters 2 passive radiators 4X 15W 95dB 1m 100 240 V AC 50 60 Hz 19V 3 4A 11 1V 2500mAh Lithium 54M Maximum lt 1W stand by 4 ohm per speaker lt 4dBm GFSK 4 DPQSK 8 DPSK DLNA Bluetooth Airplay 3 0A2DP V 1 3AVRCPv1 5 345mm X 222mm X 325mm Specifications harman kardon HARMAN 2013 HARMAN International Industries Incorporated All rights reserved Harman Kardon is a trademark of HARMAN International Industries Incorporated registered in the United States and or other countries The beautiful sound logo is a trademark of HARMAN International Industries Incorporated e Bluetooth SiPod JiPhone iPad The Bluetooth word mark and logos are regi
5. Onyx Wireless Speaker System with Rechargeable Battery Owner s Manual harman kardon harman kardon by HARMAN Onyx INTRODUCTION DESCRIPTION AND FEATURES DESIGN AND PERFORMANCE WIRELESS CONNECTION INCLUDED ITEMS CONTROLS AND CONNECTIONS ONYX TOP PANEL CONTROLS ONYX REAR PANEL CONNE CTIONS AND CONTROLS SPEAKER PLACEMENT CONNECTIONS POWER CONNECTIONS SOURCE OPTIONS WI FI CONNECTION BLUETOOTH CONNECTION WPS CONNECTION IOS WIRELESS WI FI SHARING IOS WI FI SHARING WITH CABLE AD HOC MODE OPERATION SWITCHING ON AND OFF ADJUSTING VOLUME PLAYING MUSIC THROUGH BLUETOOTH PLAYING MUSIC THROUGH WI FI PLAYING MUSIC THROUGH AIRPLAY PLAYING MUSIC THROUGH AN AUXILIARY DEVICE CONNECTING THROUGH DLNA H K REMOTE LED INDICATIONS TROUBLESHOOTING SPECIFICATIONS Table of Contents UY Ny N N N OA OA ON GN A A A A A Aa Aa A A A CC UU UU O O O N MN Onyx Introduction Thank you for purchasing the Harman Kardon Onyx HK Onyx is a premium wireless speaker with an iconic design and comes with a rechargeable inbuilt battery that allows you to stream music from any smart phone tablet or other wireless devices through Bluetooth AUX Wi Fi AirPlay and DLNA HK Onyx is a 4 speaker advanced acoustic platform and its dual passive radiators deliver a truly fantastic sound experience with a balanced soundstage and powerful bass response The Harman Kardon Remote app simplifies the setup and lets you stream all your audi
6. cable provided with your iPhone iPad or iPod touch 2 Ensure your iPhone iPad or iPod touch is connected to your Wi Fi network 3 Press the Wi Fi button on the Harman Kardon Onyx for less than a second A pop up window will be displayed on your iPad iPhone or iPod Touch with a message Share Wi Fi Settings 4 Press Allow The iPhone iPad or iPod Touch will then share Wi Fi settings with the Harman Kardon Onyx and Onyx will be connected to your Wi Fi network This takes at least 40 seconds Once the HK Onyx is connected to the network the Wi Fi LED will light constant white and a sound prompt will be heard iOS 2 WO gt 0 5s gt Allow J To connect using the H K remote app 1 Goto the Apple App store or Google Play store and download the H K Remote app 2 Click icon on the home screen to add a new device to your net work and choose Harman Kardon Onyx from the list 3 Follow the setup instructions in the app Onyx APP H K Remote H K Remote Available on the E App Store Ad hoc Mode If you have a Mac or PC computer or other phone or tablet use the following method to connect to the system 1 Put the Harman Kardon Onyx into Ad hoc mode by touching the Wi Fi button for more than 5 seconds ensure there are no USB devices plugged into the USB port 2 Goto the Wi Fi Settings page on your Mac PC or Phone and connect to the network with the name HK_Onyx This
7. he letters WPS on your router To activate WPS connection Press the WPS button on your router Press the WPS button on the Harman Kardon Onyx within 1 minute The speaker and router will then exchange Wi Fi settings and connect to each other Check your Wi Fi router manual for compatibility and more information WPS E gt p sss AUX WPS WPS wO05s 10S Wireless Wi Fi Sharing If you have an Apple device use the following method to connect your Harman Kardon Onyx to the Wi Fi network 1 Connect your iPhone iPad or iPod Touch to the speaker using Bluetooth Ensure your iPhone iPad or iPod Touch is connected to your Wi Fi network 3 Press the Wi Fi button on the Harman Kardon Onyx for less than a second A pop up window will be displayed on your iPad iPhone or iPod Touch with a message Share Wi Fi Settings 4 Press Allow Speaker Placement The iPhone iPad or iPod Touch will then share Wi Fi settings with the Harman Kardon Onyx and Onyx will be connected to your Wi Fi network This takes at least 40 seconds Once the Harman Kardon Onyx is connected to the network the Wi Fi LED will light constant white and a sound prompt will be heard 10S Wi Fi Sharing with Cable If you have an Apple device without Bluetooth connection use the following method to connect your Harman Kardon Onyx to the Wi Fi network 1 Connect your iPhone iPad or iPod touch to the speaker using the USB to 30 pin or USB to Lightning
8. increase or decrease volume These buttons are touch sensitive allowing volume control with a gentle finger touch of the buttons Adjust volume using the Volume Up and Volume Down buttons located on top of the unit Short press Increase decrease volume by 1 step Press and hold Increase decrease volume continuously 1 step per 0 2 second Playing Music through Bluetooth 1 Press the Power button The LED will illuminate white The HK Onyx enters pairing mode the first time it is switched on 2 IfHK Onyx has been paired with any source before touch and hold the Bluetooth button for at least 4 seconds 3 Perform a new device search on your Bluetooth capable device 4 Select HK Onyx BT on the device s pairing list and enter pasword as 0000 The device will be paired to HK Onyx automatically If pairing is successful the Onyx s Status LED will change to white amp O gt 2 5s g 1 oN Po Gc Pr E E AM k HK ONYX lt PH gt day cD 5 Control playback from your Bluetooth capable device 6 Youcan change the name of the speaker for easy identification using the H K Remote app Onyx Playing Music through Wi Fi To play music in your Onyx through Wi Fi 1 Press the Power button The LED will illuminate white 2 Connect to your Wi Fi network by following the above procedures 3 If Harman Kardon Onyx is on Wi Fi network the Wi Fi LED becomes constant white 4 Control playback from
9. lacement Rear view i Speaker Placement The HK Onyx being wireless and portable can be placed at a place of your choice and convenience You can place it anywhere in the room for the best sound experience Connections This section helps you understand how to connect your device correctly to a power source and different input sources Power Connections To charge the inbuilt battery connect the AC adapter to a 110 220 volt power source Source Options The speaker offers the following source connection options Bluetooth Wi Fi using AirPlay Wi Fi using DLNA Aux Input Wi Fi Connection You can connect your Onyx to Wi Fi compatible devices through the following options WPS If you have a WPS enabled router iOS Wireless Wi Fi sharing If you have an iPhone or iPad with Bluetooth iOS Wi Fi sharing If you have an iPhone or iPad and a USB to 30pin or USB to Lightning cable Ad hoc mode If you want to set up the speaker from a computer or other device Bluetooth Connection You can connect your Onyx to Bluetooth compatible devices Press the Bluetooth button for more than 4 seconds to enable Bluetooth pairing mode Onyx O gt 2 5s 9 if d J ON Mo PI p x u a WPS Connection Wi Fi Protected Setup WPS is a simple way of getting your speaker to connect to the desired network Your router may support WPS To confirm WPS connection to be active on your system look for the logo or t
10. may take around 40 seconds depending on your device 3 Open your web browser and enter the IP address as 192 168 1 1 in the address bar of your browser The following page will be displayed HK Onyx Airplay Setup Change Device Name HE Onyx F S8F00 Device Wireless 5510 4 Select the name of the Wi Fi network you want to connect from the drop down menu Device Wireless SSID 5 Enter the password for your network and click Connect A warning box will be displayed 6 Ensure that you have entered the password correctly If you are not sure click Cancel and enter the password again without any mistake The Harman Kardon Onyx will then attempt to connect to your Wi Fi network If the connection is successful the Wi Fi LED will turn white and the connection successful tone can be heard Operation NOTE To restore the factory default settings long press Bluetooth and Power button in Operational mode Operation Switching ON and OFF The power button on the top panel of the speaker allows you to set your speaker to any of the following power modes Operational mode White constant LED illumination Sleep mode Amber constant LED illumination OFF mode No illumination To change the power mode Short press Operational Sleep mode show battery status Long press OFF mode wake up to Operational mode Operational Sleep mode enter OFF mode Adjusting Volume The volume buttons on the top panel allow you to
11. o content With its simple setup quality sound and easy portability the HK Onyx is an essential audio component for every house CONTACT US For queries and clarifications please contact your service provider or browse www harmankardon com for complete details Description and Features Design and Performance HK Onyx is designed with steel and leather Dual passive radiators provide deep bass The built in rechargeable battery offers up to 6 continuous hours of playtime HK Onyx is compatible with Harman Kardon Remote app Wireless Connection Wireless connectivity allows you to place the speaker in any part of the room without having to worry over friends and family tripping over cables The HK Onyx supports almost every popular wireless device via Bluetooth or Wi Fi connections Included Items HK Onyx speaker system complete accessories consist of HK Onyx speaker One AC power adaptor Regional power cable Quick Start Guide IMPORTANT If any included accessory is missing or if any part of your HK Onyx system fails to operate properly contact your dealer immediately Controls and Connections This section will help you identify the controls and connections that are provided on the Onyx top and rear panels Onyx Top Panel Controls Introduction The following control buttons are available on the top panel of the HK Onyx Power button Volume Controls Bluetooth Wi Fi Battery level indicator e T t 9 O
12. stered trademarks owned by Bluetooth SIG Inc and any use of such marks by HARMAN International Industries Incorporated is under license Other trademarks and trade names are those of their respective owners Made for iPod Made for iPhone and Made for iPad mean that an electronic accessory has been designed to connect specifically to iPod iPhone or iPad respectively and has been certified by the developer to meet Apple performance standards Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards Please note that the use of this accessory with iPod iPhone or iPad may affect wireless performance IPad iPhone iPod and iPod touch are trademarks of Apple Inc registered in the U S and other countries Made for iPhone 5 iPhone 4S iPhone 4 iPhone 3GS iPad 3rd and 4th generation iPad 2 iPad iPad mini and iPod touch 3rd through 5th generation harman kardon by HARMAN
13. your Wi Fi enabled device Playing Music through AirPlay AirPlay allows you to wirelessly stream audio content from your your Mac or PC iPhone iPad or iPod touch to Harman Kardon Onyx iPhone iPod touch or iPad running i0S version 4 2 or higher MAC or PC running a compatible version of iTunes Playing Music through an Auxiliary Device 1 Connect the auxiliary device to the Aux in jack using a stereo 3 5mm 1 8 auxiliary cable 2 Press the Power button on top panel of the unit 3 Control music playback through the auxiliary device Connecting through DLNA DLNA in the HK Onyx helps in sharing audio data over a home network and stream audio Power LED Operation H K Remote HK Onyx can be operated through the H K Remote app available in the App Store for Apple products or Google Play for Android products You can use the H K Remote app to stream music to and control the HK Onyx through your smart phone or tablet APP H K Remote OG gt Pil LED Indications The LEDs present on the top panel of HK Onyx indicates the status of the speaker unit Refer the table below to get a fair idea on the speaker LED indications White Constant Operational mode Wi Fi LED Wi Fi connected Including connected in Ad hoc mode Wash Gomen _ Waman wrmon a Wagemeangnam U mver osan diced Ama wm Ane DleQudfish
Download Pdf Manuals
Related Search