Premier Mounts ECM-3763T flat panel ceiling mount
Contents
1. Place the mount clamp firmly against the underside of the Trio mount ring Flip the mount clamp closed Closed Position Mount Clamp Thread the locking nut onto the threaded shaft of the mount clamp Use an adjustable wrench to tighten the locking nut Make sure that the locking nut is completely tightened before releasing the eliptical mount assembly Proceed to the Attaching the Flat Panel section Page 10 Visit Premier Mounts website at http www mounts com Installation Instructions ECM 3763T 24 Attaching the Flat Panel Install the mount according to the instructions provided by Premier Mounts Ensure all structural reinforcements have been made before attaching the flat panel to the ECM 3763T Do not release the flat panel until the mounting bracket arms are fully resting on the elliptical mounting bar Raise the mounting bracket arms and the attached flat panel over the elliptical mounting bar of the ECM 3763T Mounting Bracket Arms Elliptical Mounting Bar Lower and center the mounting bracket arms with the attached flat panel onto the elliptical mounting bar of the ECM 3763T Repeat Steps 1 and 2 for mounting the remaining elliptical tilt mounts Do not release the flat panel until the mounting bracket arms are resting fully on the elliptical mounting bar Proceed to Attaching the Decorative Covers secti2. 160lbs x 3 FIVE 5 TIMES THE WEIGHT OF THE FLAT PANEL AND MOUNT IF NOT THEN THE CEILING STRUCTURE MUST BE REINFORCED Warning Statements INSTALL THE MOUNT ACCORDING TO THE INSTRUCTIONS PROVIDED BY PREMIER MOUNTS PERFORM ALL STRUCTURAL REINFORCEMENTS BEFORE ATTACHING THE FLAT PANEL TO THE CEILING MOUNT USE THE APPROPRIATE LIFTING DEVICE WHEN LIFTING THE FLAT PANEL INTO PLACE PRIOR TO THE INSTALLATION OF THIS PRODUCT THE INSTALLATION INSTRUCTIONS MUST BE READ AND comeretery UNDERSTOOD TO PREVENT PERSONAL INJURY AND PROPERTY DAMAGE KEEP THESE INSTALLATION INSTRUCTIONS IN AN EASILY ACCESSIBLE LOCATION FOR FUTURE REFERENCE PREMIER MOUNTS DOES NOT WARRANT AGAINST DAMAGE CAUSED BY THE USE OF ANY PREMIER MOUNTS STOP PRODUCT FOR PURPOSES OTHER THAN THOSE FOR WHICH IT WAS DESIGNED OR DAMAGE CAUSED BY UNAUTHORIZED ATTACHMENTS OR MODIFICATIONS AND IS NOT RESPONSIBLE FOR ANY DAMAGES CLAIMS DEMANDS SUITS ACTIONS OR CAUSES OF ACTION OF WHATEVER KIND RESULTING FROM ARISING OUT OF OR IN ANY MANNER RELATING TO ANY SUCH USE ATTACHMENTS OR MODIFICATIONS SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE ASSEMBLY OF THIS PRODUCT USE PROPER SAFETY GEAR AND TOOLS FOR THE ASSEMBLY PROCEDURE TO PREVENT PERSONAL INJURY At least two qualified people should perform the assembly procedure Personal injury and or property damage can result from dropping or mishandling the flat panel Be aware of the mounting environment If drilling and or
3. CM 3763T 24 Tilt Positioning Adjusting the Flat Panel Friction Tilt Angle Adjusting the Flat Panel to the Original Position Place one hand at the center top edge of the Place one hand at the center top edge of the flat flat panel panel Place the other hand on the center bottom Place the other hand on the center bottom edge of edge of the flat panel the flat panel Using the upper hand gently pull the top of Using the upper hand gently push the top of the the flat panel towards you while the flat panel towards the wall while the lower hand lower hand gently pushes the bottom of the gently pulls the bottom of the flat panel away from flat panel away from you the wall tn If additional tilt friction is required tighten the lower nut and lower bolt only to increase the tilt friction Lower Bolt Lower Nut Technical Specifications All measurements are in inches mm 44 46 1129 1925 489 805 204 Center of coupler 19 49 495 i to center of display Top of coupler to bottom of i display mounting bracket 21 56 548 Installation Instructions Visit Premier Mounts website at http www mounts com Page 13 gt 4 22 ECM 3763T Warranty PREMIER MOUNTS LIMITED LIFETIME WARRANTY What and Who is
4. Covered by this Limited Warranty and for How Long Premier Mounts warrants this product to be free from defects in material and workmanship for the lifetime of the original owner of this product The limited warranty is valid only for the original purchaser of the product What Premier Mounts Will Do At the sole option of Premier Mounts Premier Mounts will repair or replace any product or product part that is defective If Premier Mounts chooses to replace a defective product or part a replacement product or part will be shipped to you at no charge but you must pay any labor costs What is Not Covered Limitations PREMIER MOUNTS DISCLAIMS ANY LIABILITY FOR DAMAGE TO MOUNTS ADAPTERS DISPLAYS PROJECTORS OTHER PROPERTY OR PERSONAL INJURY RESULTING IN WHOLE OR IN PART FROM IMPROPER INSTALLATION MODIFICATION USE OR MISUSE OF ITS PRODUCTS PREMIER MOUNTS DISCLAIMS ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE PREMIER MOUNTS IS NOT RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES INCLUDING BUT NOT LIMITED TO INABILITY TO USE ITS PRODUCTS OR LABOR COSTS FOR REMOVING AND REPLACING DEFECTIVE PRODUCTS OR PARTS SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU What Customers Must Do for Limited Warranty Service If you discover a problem that you think may be covered by
5. Screws Qty 6 M6 x 25mm Phillips Screws Qty 6 Thread Depth Indicator Qty 1 94 Allen Wrench Qty 1 Installation Instructions Visit Premier Mounts website at http www mounts com Page 3 gt 4 24 ECM 3763T Parts List con d Mounting Hardware Standard Hardware M6 x 20mm Phillips Head M4 x 16mm Phillips Head Screw Qty 18 Screw Qty 24 M4 x 25mm Phillips Head M6 x 30mm Phillips Head Screw Qty 12 Screw Qty 18 M5 x 12mm Phillips Head Screw Qty 18 M8 x 20mm Phillips Head M5 x 16mm Phillips Head Screw Qty 18 Screw Qty 18 M8 x 25mm Phillips Head M5 x 20mm Phillips Head Screw Qty 18 Screw Qty 18 M5 x 25mm Phillips Head M8 x 30mm Phillips Head Screw Qty 12 Screw Qty 18 M8 x 35mm Phillips Head M5 x 50mm Phillips Head Screw Qty 12 Screw Qty 12 M8 x 70mm Phillips Head M6 x 12mm Phillips Head Screw Qty 12 Screw Qty 24 s Nylon Spacers Qty 18 Griplate 1 Nylon Spacers Washers Qty 24 Qty 18 Ys Nylon Spacers Qty 18 Nylon Sleeves Qty 12 AST 2446 2 Qty 1 2 Nylon Spacers Large Qty 36 M8 x 16mm Cap PPE 4 4 Nylon Spacers Large Screw Qty 2 Qty 18 5 Flat Washer Metal M8 Wave Qty 18 Washers Qty 2 Page 4 Visit Premier Mounts website at htt
6. cD PREMIER Cag MOUNTS The original holding company INSTALLATION INSTRUCTIONS Elliptical Ceiling Mount for 37 to 63 Flat Panels Model ECM 3763T NORTH AMERICA EUROPE AUSTRALIA AND OCEANIA 3130 East Miraloma Avenue Swallow House Distributed by Amber Technology Limited Anaheim CA 92806 USA Shilton Industrial Estate Unit B 5 Skyline Place USA and Canada Shilton Coventry England CV79JY Frenchs Forest NSW 2086 Phone 1 800 368 9700 Phone 44 0 2476 614700 Australia Fax 1 800 832 4888 Fax 44 0 2476 614710 Phone 61 2 9452 8600 Sydney Office Other Locations Toll Free 1 800 368 9700 Phone 001 714 632 7100 Email mounts ambertech com au Fax 001 714 632 1044 9531 007 034 00 gt 4 E ECM 3763T Weight Capaclty 5 4 dessert tee E E E S eee ated San E en nse ieee 2 WANING STALSmM ents aie aes stg cs aN sacet ehes a cadasansctcets tasactetaniavactivensa nis ce esiaca E ti 2 Installation TOOIS avis tececcsvi ie Paice eae ets et ie eee as ee a ae cele 3 Mounting HardWare peene a amr rrr rer rrrree ter a hier rreran Meter teh ase rrr here mr em ret Perera ferry Teme treet tprrte 4 FO AtUieS s sisicaceviicceeds Aaacedtas a i E a aaea a AOTEA E E EEEN EEE Sa EEEE A ap tyes EEE yedougeen eens 5 Attaching the Ceiling Mount sree i erea ceed sence a e a ae nena Eare e e e eee e a aa e E aE EEEE 6 Selecting the Proper Mounting Hardware 2 c ccccccceecceceeeceeeaeceeeeeceaeceeeecaaaaeaeeeecesaaaeceeegec
7. cutting into the mounting surface always make sure that there are no electrical wires in the ceiling Cutting or drilling into an electrical line may cause serious personal injury Make sure there are no water or natural gas lines inside the ceiling where the mount is to be located Cutting or drilling into a water or gas line may cause severe property damage or personal injury This product is intended for indoor use only Use of this product outdoors could lead to product failure and or serious personal injury Do not install near sources of high heat Do not install on a structure that is prone to vibration movement or chance of impact Contact Premier Mounts with any questions 800 368 9700 techsupport mounts com Page 2 Visit Premier Mounts website at http Awww mounts com Installation Instructions ECM 3763T e Installation Tools The following tools may be required dependent upon your particular installation These tools are not provided by Premier Mounts but you can purchase them at your local hardware store Protective Eye Phillips Tip Tape Measure Wear Screwdriver Pencil Adjustable Wrench Ladder ECM 3763T Mount Hardware Mount Ring Qty 1 AL q A Decorative Covers Qty 6 PEF TEF M4 x 6mm Phillips
8. e AST 2446 2 must be threaded in a minimum four 4 turns Use the screwdriver to tighten the set screw once the AST 2446 2 has been attached EF QQa2e2 QBHAOQAOBoB 2 A0QA8QFQOQAOBABOA The following steps must be performed by a minimum of three people Two people lift the trio mount into place Align the upper and lower halves of the AST 2446 2 Slide the lower half trio mount into the upper half Upper Half of the AST 2446 2 It is recommended that the height and location of the ECM 3763T be determined prior to performing the following steps Lower Half Determine the mounting height Align the M8 mounting holes on the upper and lower halves of the AST 2446 2 and insert the M8 screws and wave washers Use the 3 wrench to tighten the M8 screws Minimum four 4 f complete turns Verify that all hardware is secure and tight before S proceeding to the next section LZ p a f Ke Proceed to the Selecting the Mounting Hardware aaa section LDS diy diy A diy Set Screw Threaded Coupler Page 6 Visit Premier Mounts website at http Avww mounts com Installation Instructions ECM 3763T 24 Selecting the Proper Mounting Hardware Insert the Thread Depth Indicator into the thread inserts found on the bottom or top of the projector Use a pencil to mark the depth of the thread insert on the Thread Depth Indicator as shown in Fig
9. eaeceeeesaaaeaeeeeseqeaeeeeesenanaees 7 Griplate Washer INStallation scsiss sceseadesetecseeccecvedeves seex eek entiteit de Medaceedideteicestedeseeeddeeleeedsqiend She eieidibancdees ieee eesse eee 8 Nylon Spacerninstalation sc esne a es seseec es tesoisenecatasasensedent sab e Seatiseasectacasesecees css 8 Removing the LOCKING Nt eerren riese deere e Eee r eE Ea EE e a r a eie eE EE a be ee tE de eree eaaa 9 Determining the Mounting Placement cccccccececeeeeeececeeeeeaeee ee eeeaaeaeeeeeeeeaeae dta dir iS Eri REEr EASi Pee iE EOE eeina Corr E NEEE Ario EESE EEEE 9 Elliptical Tilt Mount InstallatiON seisseen eeen Es A a E AESA E E EEA aN AEAEE ANRE Aa tamaie uaa Aea AAEE FANENE 10 Attaching the Flat Panel ascatkacukiiaa sisi eni a eE E a a a a E a aaaea ER EN Eaa vk E E 11 Attaching the Decorative COyef Ssss nsiro cues desea aeesanceardenacedcandacneea noche snes arri ia ae r oi ia e eaii 12 Cable Management sii isssidiestesteas ates adie nntaees E RA anes NE TOR inet EEEE ENEAN PERE OPE SE NENA ENT EOU E EE ENE EE E SEENEN EESE 12 Mil POS MOWING seee e a cass eed e a ea a E a EE canescens 13 Technical Specifications i nnen aana EE ANEA sci AE EAA AE EE EA vues EREA EE AREER EE EAO EAEE EAA e AAE EE EEA E riai 13 Wanian Yeten a a a a E pee mcr rr tre trier pratt 14 Be eonte e A E A E A E E cesetanaaustenvaaraveseerersaatess 14 Weight Capacity THE CEILING STRUCTURE MUST BE CAPABLE OF HOLDING Maximum flat panel weight
10. er must be installed between the head of the mounting screw and the mounting bracket as shown Does your flat panel have Recessed mount points Uneven mount points Acurved back Any obstruction near the mount point If Yes you must install nylon spacers Remove the mounting brackets Griplate washers and mounting screws from the back of the flat panel Proceed to the A Mounting Scre Nylon Spacer Installation section SENG 7 l Griplate Washer If No skip to the Removing the Locking Nut section Nylon Spacer Installation Mounting Bracket Premier Mounts nylon spacers allow you to attach the mounting bracket to flat panels which have recessed or uneven mount points Each nylon spacer will add distance between the mounting bracket and your flat Flat Panel panel The nylon spacers must only be installed between Nylon Spacer the mounting bracket and your flat panel The nylon spacers will fit M4 M5 M6 and M8 screw sizes Proceed to the Removing the Locking Nut section a GOCOCGCCeGEa C t C OGOGCOAAA ooo 02900000000000000 Page 8 Visit Premier Mounts website at http www mounts com Installation Instructions ECM 3763T Removing the Locking Nut Locate the locking nut on top of the mount clamp An adjustable wrench may be used to loosen the locking nut if it is too tig
11. ht Remove the locking nut and and set it to the side Proceed to Determining the Mount Placement section Determining the Mounting Placement Do not use different size flat panels with the ECM 3763T If one 63 flat panel is used the remaining two flat panels must be 63 as well Different size flat panels will cause unequal weight distribution Please refer to the illustration to the right for mounting placement Measure the distance between the mount arm braces Divide this measurement by 2 Measure directly out from the junction point of the mount to the outer ring Mark this location as the mounting clamp will be attached at this marking Repeat through for the remaining mount placement points Proceed to the Eliptical Tilt Mount Installation section Adjustable Wrench Locking Nut Mount Clamp Mount Arm Brace Junction Point Outer Ring Marking tin 63 flat panel shown above Installation Instructions Visit Premier Mounts website at http www mounts com Page 9 gt ECM 3763T Elliptical Tilt Mount Installation The following steps must be completed by two people Do not release the elliptical tilt mount until the mount clamp is been fully engaged and the locking nut is attached and tightened After determining the required distance between each mounting point lift the eliptical mount assembly up to the Trio mount ring
12. on Installation Instructions Visit Premier Mounts website at http www mounts com Page 11 b a 24 ECM 3763T Attaching the Decorative Covers When attaching the decorative covers verify that the smaller mounting hole is above the larger mounting hole Place the first decorative cover over the first Decorative mounting bracket arm and push firmly into im Cover place Align the mounting holes together Insert the M4 x 6mm Phillips screw smaller mounting hole Insert the M6 x 25mm Phillips screw larger mounting hole Use a screwdriver to tighten all decorative cover mounting hardware Repeat Steps 1 through 5 for the remaining decorative covers and mounting bracket arms A Do not overtighten these screws Proceed to the Cable Management section M4 x 6mm Screw Screwdriver M6 x 25mm Screw Cable Management Route the cables through the cable access holes and to their respective locations Remove the plastic covers route the cables and gently re attach the plastic covers The cables may then be routed through the bracket up the ceiling adapter and into the ceiling to a predetermined power source Proceed to the Tilt Positioning section Source or A V Cable Page 12 Visit Premier Mounts website at http www mounts com Installation Instructions E
13. p Awww mounts com Installation Instructions ECM 3763T Features Installation Instructions Visit Premier Mounts website at http Awww mounts com Mounting Ring NPT Threaded Pipe not included Threaded Coupler 15 Tilt Slide Cable Access Port Mounting Bracket Arm Decorative Cover Page 5 gt 4 22 ECM 3763T Attaching the Ceiling Mount The ceiling should be capable of supporting a weight of at least five times the product weight If not the ceiling surface must be reinforced Proper installation procedure by qualified personnel as outlined in the installation instructions must be adhered to Failure to do so could result in serious AST 2446 2 M8 Allen Head personal injury Screw Allen Wrench Mounting hardware is not included with this product Commercially available hardware must be used for this installation The hardware used will depend on your installation environment i e wood stud concrete surface metal l beam etc Separate the upper and lower halves of the es Upper Half AST 2446 2 by removing both M8 screws and wave washers Unpack the trio mount and place it on the ground The set screw on the threaded coupler must be backed out in order for the AST 2446 2 to be threaded into place Thread the lower half of the AST 2446 2 into i Lower Half the threaded coupler on the trio mount g The lower half of th
14. the warranty you MUST REPORT it in writing to the address below within thirty 30 days Proof of purchase an original sales receipt from the original consumer purchaser must accompany all warranty claims Warranty claims must also include a description of the problem the purchaser s name address and telephone number General inquiries can be addressed to Premier Mounts Customer Service at 1 800 368 9700 Warranty claims will not be accepted over the phone or by fax Premier Mounts Attn Warranty Claim 3130 East Miraloma Ave Anaheim CA 92806 How State Law Applies THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE Disclaimer Premier Mounts intends to make this manual accurate and complete However Premier Mounts makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind Premier Mounts makes no representation of warranty expressed or implied regarding the information contained herein Premier Mounts assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document Premier Mounts 2009 Page 14 Visit Premier Mounts website at http www mounts com Installation Instruc
15. tions
16. ure i Insert the Thread Depth Indicator into the remaining thread inserts to compare and verify their depth Locate the correct diameter screw for the thread insert If the screw you selected is longer than the mark J ee on the Thread Depth Indicator as shown in Figure Inverted i KT 2 and Figure 3 do not use this screw The screw Projector Threaded length must not bypass the mark Thread Depth Select another screw length until you find a screw indicator that comes closest to the mark without going past the mark Test each size of the screws provided The correct screws should thread easily into the i m _ 5 mount point and not pull out when tension is ye OSE applied hread Depth hread Depth Depth Mark TI Depth Mark T Indicator Indicator The optional M3 flat washers may be used to Figure 2 Figure 3 decrease the screw depth of either the M2 5 x 12mm screws or the M3 x 16mm screws Decrease the screw depth by placing an M3 flat washer inside the leveling barrel and then inserting the mounting screw Installation Instructions Visit Premier Mounts website at http www mounts com Page 7 ECM 3763T Griplate Washer Installation Premier Mounts Griplate Washers are designed to accommodate the various M4 M5 M6 and M8 hole sizes required by flat panels Do not place excessive pressure on the back of the flat panel as this may damage your flat panel The Griplate Wash
Download Pdf Manuals
Related Search