EK Water Blocks EK-BAY RES
Contents
1. M3x4 DIN 7985 screws threaded port EK CSQ OUTLET G1 4 compression fittings threaded port Revision 1 0 Released on 9 of August 2013 VERY IMPORTANT NOTICE Once the installation is completed it is a recommended practice to test the cooling circuit for leaks prior to powering up the computer We recommend a 24 hour leak test prior to powering up the computer Do not test the water block using tap water pressure This will rupture the top of the housing and render the block unusable and will void your warranty While all efforts have been made to provide the most comprehensive tutorial possible EK Water Blocks assumes no liability expressed or implied for any consequential damage s occurring to your equipment as a result of using EK Water Blocks cooling products either due to errors or omissions on our part in the above instructions or due to failure or defect in the EK Water Blocks cooling products WARRANTY Our products are warranted against defects in materials or workmanship for a period of 24 months beginning from the date of delivery to the final user During this period products will be repaired or have parts replaced at our discretion provided that I the product is returned to the agent from whom it was purchased II the product has been purchased by an end user and has not used for commercial purposes IIT the product has not been misused handled carelessly or used in a manner other than in accordance with the instructions prov2. stock O rings into the pumps Computer chassis Free one slot in case they are already occupied with other groove Use enclosed Allen key to secure the pumps with eight 8 M4x25 Computer components such as optical or hard disk drives Place the reservoir screws in your 5 25 drive bay out with the front plate facing outwards Use 8 M4x25 DIN 7984 screws After completing STEP 6 in this manual secure the reservoir to the drive bay to mount the pumps to the top cage using the enclosed eight 8 M3x4 DIN 7985 screws with Philips head Use the enclosed Allen key screwdriver M3x4 DIN 7985 screw It is mandatory to use the correct INLET and OUTLET port As Fill reservoir through G3 8 threaded fill port marked with arrow and make sure an inlet and outlet port you need to use exactly those ports that are liquid is not spilled over your computer or any electrical devices nearby Run your shown in the figure below EK recommends using EK CSQ compression pumps shortly for couple of times to make sure water floods your tubes and other fittings for best water cooling experience water cooling components Pay attention to the water level in your reservoir Lowest and highest recommendable water levels are indicated on the reservoir s front panel MIN MAX Once done with the filling process please close your EK BAY Res Dual INLET G1 4 L Serial reservoir with G3 8 plug and tighten the seal using enclosed Allen key Now secure the bay reservoar with
3. Installation and mounting manual for EK BAY Res Dual DDC Serial reservoir This product is intended for installation only by expert users Please consult with a qualified technician for installation Improper installation may result in damage to your equipment EK Water Blocks assumes no liability whatsoever expressed or implied for the use of these products nor their installation The following instructions are subject to change without notice Please visit our web site at www ekwb com for updates Before installation of this product please read important notice disclosure and warranty conditions printed on the back of the box The barb hose fittings require only a small amount of force to screw them in otherwise the high flow fittings might break These fittings do not need to be tightened with much force because the liquid seal is made using O rings The use of an algaecide and corrosion inhibitors is always recommended for any liquid cooling system Sample picture of the EK BAY Res Dual DDC reservoir Take your Laing DDC pump Unscrew the screws that connect stock top usually you will need a Torx T20 head screwdriver at the bottom POM acetal reservoir and put the top away as you don t need it any more Keep it for a bodv warranty reason if pump stops working Take motor with impeller of your Laing DDC pump Place it according to the This reservoir occupies one 1 5 25 drive bay expansion slot in your picture Do not forget to place back the
4. ided describing its installation and proper use This warranty does not confer rights other than those expressly set out above and does not cover any claims for consequential loss or damage This warranty is offered as an extra benefit and does not affect your statutory rights as a consumer This warranty is voided if the product comes in contact with aggressive UV additives or other improper liquids this paragraph is intentionally left blank REQUIRED TOOLS Philips and Torx T20 head screwdriver Revision 1 0 Released on 9 of August 2013
Download Pdf Manuals
Related Search