Hunter Low Profile III
Contents
1. Table of Contents www HunterFan com 1 888 830 1326 Congratulations on purchasing What to Expect with your new Hunter ceiling fan It will Your Installation Tools Needed Ceiling Bracket Preparation provide comfort and performance in your home or office for many years This installation and operation manual contains complete instructions for installing and operating your fan We are proud of our work and appreciate the opportunity to supply you with the best ceiling fan available anywhere in the world To register your fan please visit www HunterFan com register Maintenance Operation amp Cleaning Y uN TYG N M0047 01 11 26 12 Hunter Fan Company What to Expect with Your Installation If you are unfamiliar with wiring use a qualified electrician Must be able to secure the fan to building structure or fan rated outlet box a Know your wiring You may need a friend to help you Check box to see fan weight 30 inches from blade tip to nearest wall or obstruction 7 feet from bottom edge of blade to the floor A Assess location 2 M0047 01 11 26 12 Hunter Fan Company www HunterFan com 1 888 830 1326 Read and Save These Instructions This product conforms to UL Standard 507 WARNINGS w 1 To reduce the risk of fire electrical shock or personal injury mount fan direct2. leave unattended Housing Screw R With a Phillips head screwdriver install the four motor housing screws found in the hardware bag Tighten all four screws securely M0047 01 11 26 12 Hunter Fan Company www HunterFan com 1 888 830 1326 q Blades www HunterFan com 1 888 830 1326 Insert grommets found in the W hardware Lightly attach the blade irons to the bag into the holes in the blades then motor with screws found in secure each blade to a blade iron with the X hardware bag then securely screws found in the A hardware bag tighten after both screws are attached Your blades are shielded with Dust Armor which is ananotechnology coating that repels dust For cleaning the fan use soft brushes or cloths to prevent scratching Cleaning agents may damage the finishes M0047 01 11 26 12 Hunter Fan Company 1 888 830 1326 hardware bag into place and then tighten all three 3 screws www HunterFan com Insert the third screw found in T R LAAAAALALALALAS i secure all three assembly screws could result in the attached to the mounting plate Failure to properly switch housing fixture falling Make sure the upper switch housing is securely the Wiss AA Q pi then wrap keyhole slots around the screws and twist counterclockwise See ap Te aD U eD iG A oa O 5
3. Fan com 1 888 830 1326 Note Fan style may vary www HunterFan com 1 888 830 1326 Note To connect the wires hold the bare metal leads together and place a wire connector over them then twist clockwise until tight 6ulpunosb d 4 MO JaA U3215 papunosb Y M papunojbun yrelg Using orange wire connectors from Using an orange wire the amp hardware bag connector from connect the black wire the W hardware bag _ ungrounded from the connect the 3 grounding ceiling to the black and wires green green the blue wires from the yellow stripe or bare fan Connect the white copper coming from the wire grounded from ceiling downrod and the ceiling to the white hanging bracket a wire from the fan Green Yellow Stripe G D 5 z D P of os D Turn the splices upward and push them carefully back through the hanger bracket into the outlet box Spread the wires apart with the grounded wires on one side of Refer to CAUTION c 1 on pg 2 the outlet box and the ungrounded wires on the other side of the outlet box M0047 01 11 26 12 Hunter Fan Company Motor Housing Raise the motor housing up over the motor and ceiling bracket Turn the motor housing so the screw holes align and the indentation in the housing locks into place with the notch in the ceiling bracket The motor housing is not secured until the next step is complete Do not
4. O p aS 5 O 3 Q aD z eD iG O aD ap LL M0047 01 11 26 12 Hunter Fan Company hole of the upper switch housing A Z A z Namas E hardware bag halfway into the motor housing It does not matter Le N D gt aN Screw two 2 housing assembly screws which two screw holes you choose from the Switch Housing rad Switch Housing www HunterFan com 1 888 830 1326 switch housing screws found in Connect the fan pull chain the lower switch housing with pendant to the short chain the bag Connect the plugs the screws on the upper switch coming from the switch housing from the upper and lower switch housing Twist the lower switch housings Make sure to line up housing clockwise to lock into the colored markings on the place Install the third switch plug connectors housing screw Tighten all three screws securely Make sure the lower switch housing is securely attached to the upper switch housing Failure to properly secure all three assembly screws could result in the light fixture falling M0047 01 11 26 12 Hunter Fan Company www HunterFan com 1 888 830 1326 Cleaning the fan use soft brushes or cloths to prevent scratching Cleaning products may damage the finishes SA Ny f N i fl
5. ly from building structure and or an outlet box marked acceptable for fan support of 70 Ibs 31 8 kg and use the mounting screws provided with the outlet box w 2 To avoid possible electrical shock before installing or servicing your fan disconnect the power by turning off the circuit breakers to the outlet box and associated wall switch location If you cannot lock the circuit breakers in the off position securely fasten a prominent warning device such as a tag to the service panel w 3 To reduce the risk of fire electrical shock or motor damage use only Hunter Solid State Speed Controls w 4 To reduce the risk of personal injury do not bend the blade brackets when installing the blade brackets balancing the blades or cleaning the fan Do not insert foreign objects in between rotating fan blades CAUTIONS c 1 All wiring must be in accordance with national and local electrical codes ANSI NFPA 70 If you are unfamiliar with wiring use a qualified electrician c 2 Use only Hunter replacement parts Tools Needed www HunterFan com 1 888 830 1326 amp Power Drill 9 64 Drill Bit a Screwdrivers optional optional If mounting to a support structure you will also need these tools 3 M0047 01 11 26 12 Hunter Fan Company ejo Ceiling Bracket www HunterFan com 1 888 830 1326 Use wood screws Use machine screws included when securing
6. ow move the reverse switch to the opposite position Changing the direction of air TN A low and off J medium 1 M0047 01 11 26 12 Hunter Fan Company The pull chain controls the fan high e2 6 Ko W v e 5 ems U Q J S U d Switch Housing continued Troubleshooting www HunterFan com 1 888 830 1326 Fan doesn t work Excessive wobbling Noisy Operation e Make sure power switch is on e Tighten all of the blade and e Tighten the blade and blade l blade iron screws until they iron screws until they are snug Pull the pull chain to make sure are snug it is on e Check to see if any of the e Use the provided balancing blades are cracked If so replace Push the mMotgr reversing switch kit and instructions to balance all of the blades firmly left or right to ensure that the fan it is engaged Check the circuit breaker to ensure the power is turned on Make sure the blades spin freely Turn off power from the circuit breaker then loosen the canopy and check all the connections according to the wiring diagram on page 7 Check the plug connection in the switch housing M0047 01 11 26 12 Hunter Fan Company
7. provided with outlet to support structure with box when securing to approved electrical outlet existing ceiling fan rated Make sure all four 4 bumpers are still attached box Drill 9 64 pilot holes outlet box Make sure in support structure toaid itis securely installed in securing ceiling bracket and is acceptable for fan with hardware foundin support of 31 8 kg 70 Ibs the X hardware bag or less To avoid possible electrical shock before installing your fan disconnect the power by turning off the circuit breakers to the outlet box associated with the wall switch location Refer to warning w 1 on pg 2 M0047 01 11 26 12 Hunter Fan Company ogo Ceiling Bracket continued Preparation www HunterFan com 1 888 830 1326 Time Saver Tip Get a helper to insert grommets found in the Il hardware bag into the blades while you re doing the next couple of steps 5 M0047 01 11 26 12 Hunter Fan Company Hanging the Fan Ground Wire While holding the wires out of the way lift the motor assembly and place the square hanger into the opening in the ceiling bracket Be sure the ground wire attached to the hanger faces out of the large opening in the ceiling bracket Locking Screw Once the motor is in the ceiling bracket use the two locking screws found in the X hardware bag to secure the motor to the ceiling bracket M0047 01 11 26 12 Hunter Fan Company www Hunter
Download Pdf Manuals
Related Search