Chief CMSH3 projector accessory
Contents
1. key C to lock mount in its current position See Figure 2 Figure 2 NOTE Micro height adjustment is still possible with set screw tightened but the set screw must be loosened in order to adjust height with the quick release button See Adjustments section for details Figure 1 CMSH3 Installation Instructions 3 Thread projector mount onto interior pipe by rotating until hand tight See Figure 3 rear view 9 lt gt 2 RSM shown Figure 5 Figure 3 4 Complete installation following projector mount installation instructions ADJUSTMENTS Micro Height Adjustment 1 Rotate micro adjustment collar to raise or lower projector mount as desired See Figure 4 K micro adjustment collar Figure 4 Quick release Button Height Adjustment 1 Loosen locking set screw with 5 64 hex key C to release quick release button adjustment mechanism See Figure 5 2 Press quick release button and adjust height to desired level See Figure 5 3 Tighten locking set screw with 5 64 hex key C to lock mount in its current position See Figure 5 Installation Instructions CMSH3 CMSH3 Installation Instructions Installation Instructions CMSH3 CMSH3 Installation Instructions E F USA International Our Mounts Your Vision Europe Chief Manufacturing a p2. INSTALLATION INSTRUCTIONS 3 Micro Height Adjust Accessory a CHIEF CMSH3 Our Mounts Your Vision CMSH3 Installation Instructions DISCLAIMER Milestone AV Technologies Inc and its affiliated corporations and subsidiaries collectively Milestone intend to make this manual accurate and complete However Milestone makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind Milestone makes no representation of warranty expressed or implied regarding the information contained herein Milestone assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document Chief is a registered trademark of Milestone AV Technologies All rights reserved A IMPORTANT WARNINGS AND CAUTIONS WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions DIMENSIONS WARNING Failure to read thoroughly understand and follow all instructions can result in serious personal injury damage to equipment or voiding of factory warranty It i
3. roducts division of Milestone AV Technologies 8800 002062 Rev00 2010 Milestone AV Technologies a Duchossois Group Company www chiefmfg com 11 10 Asia Pacific gt TU 8401 Eagle Creek Parkway Savage MN 55378 800 582 6480 952 894 6280 877 894 6918 952 894 6918 Fellenoord 130 5611 ZB EINDHOVEN The Netherlands 31 0 40 2668620 31 0 40 2668615 Office No 1 on 12 F Shatin Galleria 18 24 Shan Mei Street Fotan Shatin Hong Kong 852 2145 4099 852 2145 4477 DI 2 2 ORCONsUMERS
4. s the installer s responsibility to make sure all components are properly assembled and installed using the instructions provided WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of all components attached to the CMSH3 does not exceed 25 Ibs 11 34 kg The weight capacity of the CMSH3 may be LIMITED to the lowest weight capacity of any other components located between the CMSH3 and the supporting structure Lg TLS WPT THREAD 1 5 11 5 NPS THREAD I 6 0 C 161 9 5 38 I PRESSED LENG TH iti 1 21 EXTENDED LENGTH PICHIEE CHIEF MEASUREMENTS MILLIMETERS INCHES Installation Instructions CMSH3 TOOLS REQUIRED PARTS PROVIDED so 5 64 included 1 CMSH3 cu B 1 5 64 8 32 x 3 8 ATTACHING CMSH3 TO CEILING PIPE 2 Secure CMSH3 to ceiling pipe using 5 64 hex key and 8 32 x 3 8 set screw B See Figure 1 1 igus th i A onto ceiling pipe until hand tight See MOUNTING PROJECTOR MOUNT TO CMSH3 Li ee 1 Press quick release button to lower interior pipe to desired mounting height See Figure 2 2 Tighten locking set screw with 5 64 hex
Download Pdf Manuals
Related Search