Zotac ZBOX nano ID62
Contents
1. 4 Setting up your system 4 Care during use 4 Welcome 5 Package contents 5 Getting to know your ZOTAC ZBOX nano 6 Front view 6 Rear V eW 7 BIOS settings of specific functions 8 How to disable the ring LED indicator 8 How to enable USB 2 0 charge for S3 S4 Sleep status 9 How to disable integrated IR receiver 10 Customizing the ZOTAC ZBOX nano 12 Installing a memory module 13 Installing a hard disk 14 Connecting a S PDIF cable2. 24 ZOTAC ZBOX nano Product specifications Chipset e Intel NM70 Product Dimensions e 127 x 127mm x 45mm Onboard CPU Intel Core processor 1007U dual core 1 5GHz Onboard graphics Intel HD Graphics HDMI amp DP output Memory support One 204 pin DDR3 1600 1333 SO DIMM slot Up to 8 GB of memory USB ports Four USB 2 0 ports amp two USB 3 0 ports Storage support SATA 6 0 Gb s transfer rates Supports one 2 5 inch SATA HDD or SSD 9 5mm max height One eSATA port Network support Gigabit 10 100 1000Mbps LAN IEEE 802 3 compatible WiFi BT support e Compliant with IEEE802 11b g n standard High speed wireless connection up to 300 Mbps Fully qualified Bluetooth v4 0 Audio 2 channel high definition audio Jack sensing compatible Optical SPDIF Operating System support e Windows 7 amp Windows 8 32 bit and 64 bit support IR receiver Support carrier frequencies 36k Hz ZOTAC ZBOX nano Safety information Your ZOTAC ZBOX is designed and tested to meet the latest standards of safety for information technology equipment However to ensure your safety it is important that you read the following safety instructions Setting up your system Read and follow all instructions the documentation before you operate your system Do not use this product near water or a heat source such as a radiator Set up the
3. Playback Recording Sounds Communications Select a playback device below to modify its settings Philips 234EL Intel R Display Audio Default Device Speakers Realtek High Definition Audio Ready Realtek Digital Output Realtek High Definition Audio Ready Configure 1 Access the Sound settings via the system Control Panel 2 Under Playback devices click the display device that corresponds with your HDMI audio compatible display 3 Click the Set Default button in the lower right hand corner 4 Click OK to exit the setup 24 291 MA247 00 Qe Time WWW ZOTAC COM
4. 10 Save amp Exit Press F10 to save the configuration and exit The PC will reboot How to enable USB 2 0 charge for S3 SA Sleep status 1 2 In PowerManage menu select USB 2 0 53 54 55 Charge Function and press lt Enter gt Use the arrow keys to enter the item Front Left Right USB2 0 S3 S4 S5 Charge and select Enabled Front Left USB2 harge Disabled Front Right US S5 Charge Disabled Front Left USB2 0 53 54 55 Charge Enabled Enter Dbl Click Change Opt Fi General Help F2 Previous Values F9 Optimized Befaults 10 Save 8 Exit D Right Click EXE ZOTAC ZBOX nano 3 Press F10 to save the configuration and exit Note Before charging via USB 2 0 in S5 status please make sure the Deep S5 Deep Sleep in PowerManage menu is disabled X Setting Advanced PcHealth Boot Security Save amp Exit Enabled Enabled Enabled Enabled Select Screen Enter Dbl Click Select Change Opt Fi General Help F2 Previous Values F3 Optimized Defaults 10 Save amp Exit How to disable integrated IR receiver 1 Use the arrow keys to navigate to the Advanced menu and select CIR Controller Main X Setting PcHealth PowerManage Boot Security Save amp Exit Enabled Realtek Ethernet Controller Configuration Ente Click Change Opt Fi General Help F2 Previous Values F9 Optimized Defaults 10 Save 8 Exit 10 ZOTAC ZBOX nano 2 Enter CIR Contro
5. 15 Setting up the ZOTAC ZBOX nano 16 Positioning ZOTAC ZBOX nano 18 Mounting the ZOTAC ZBOX nano to a LCD monitor 18 IR receiver 19 Remote control optional 20 Function keys 20 Lithium Battery installation 21 Installing drivers and software 22 Installing an operating system 22 Installing system drivers 22 Using your ZOTAC ZBOX nano 23 Configuring wireless connection 25 Configuring wired connection 23 Using a static P 23 Using a dynamic IP PPPoE connection 24 Configuring audio output via an HDMI device
6. now YOUR PALM SIZED MINI PC lt lt BuurrDOTH D 11 LLL EL ZOTAC ZBOX nano ID62 ZOTAC ZBOX nano D62 PLUS USER S M aNuUaL ZOTAC ZBOX nano ZOTAC ZBOX nano User s Manual No part of this manual including the products and software described in it may be reproduced transmitted transcribed stored in a retrieval system or translated into any language in any form or by any means except documentation kept by the purchaser for backup purposes without the express written permission of ZOTAC Products and corporate names mentioned in this manual may not be registered trademarks or copyrights of their respective companies and are used for identification purposes only All trademarks are the property of their respective owners Every effort has been made to ensure that the contents of this manual are correct and up to date However the manufacturer makes no guarantee regarding the accuracy of its contents and reserves the right to make changes without prior notice CAUTION Risk of explosion if the battery is replaced with an incorrect type Batteries should be recycled where possible Disposal of used batteries must be in accordance with local environmental regulations ZOTAC ZBOX nano Table of Contents Product specifications 3 Safety information
7. Utility Software Usb Charger setup exe X your driver disk letter Click the icon b to review the Page 2 of the driver DVD E SATA Controller c amp Each driver must be installed individually to ensure proper operation of the ZOTAC ZBOX nano 3 Select the driver you want to install The driver installer should launch 4 Follow the onscreen instructions for the selected driver to install 5 Restart the system Using your ZOTAC ZBOX nano Configuring wireless connection Please follow the instructions below to connect to a wireless network 1 Double click the wireless network icon pic in the notification area 2 Select the wireless network you want to connect to from the list and click Connect 3 After connection is established you will see Connected Note 1 For security concerns Do NOT connect to an unsecured network otherwise the transmitted information without encryption might be visible to others Note 2 Enter the network security key if necessary 4 10 10AM Configuring wired connection Using a static IP 1 Right click the network icon in the notification area and select Open Network Connections 2 Right click Local Area Connection and ndi Obtain an IP address automatically se l ect ro pe rti es Use the idiots IP address IP address 3 Highlight Internet Protocol TCP IP sarete Default gateway and click Prop
8. Optical S PDIF adapter 2 Locate the front panel and connect the mini Optical S PDIF adapter to the headphone mini Optical S PDIF jack ZOTAC ZBOX nano Setting up the ZOTAC ZBOX nano Please connect your peripherals before using your ZOTAC ZBOX 1 Connecting a DisplayPort display Connect the DisplayPort connector to the DP port 2 Connecting USB 3 0 device Connect USB 3 0 devices such as external hard drives SSDs and flash drives to the USB 3 0 port 3 Connecting USB 2 0 device Connect USB 2 0 devices such as wired wireless keyboards mice and printers to the USB 2 0 ports 4 Connecting the WiFi antenna module Connect the WiFi antenna module to the WiFi antenna connector ZOTAC ZBOX nano Turning on the system Connect the supplied AC adapter to the DC IN jack on the system rear panel and then press the power switch on the front panel to turn on the system Connecting to an HDMI display Connect one end of an HDMI cable to the HDMI port on the system rear panel and the other end to a HDMI compatible display such as an HDTV or monitor When both the HDMI and the DP are connected the audio output is from HDMI by default Connecting to a network device Connect one end of a network cable to the LAN port on the system rear panel and the other end to a network hub switch or router Connecting an eSATA device Connect the eSATA cable to the eSATA port Note When your ZOTAC ZBOX nano is not in use unplu
9. RJ 45 LAN port supports standard Ethernet cable for connection to a local area network LAN with speeds of 10 100 1000Mbps 6 USB 2 0 ports The USB Universal Serial Bus ports are compatible with USB devices such as keyboards mice cameras and hard disk drives 7 eSATA port The external SATA port is compatible with e SATA devices such as external hard drives and Blu ray drives 8 WiFi antenna connector The WiFi antenna connector supports the included WiFi antenna 9 Ventilation area The ventilation area is vital for proper system cooling Do not cover ZOTAC ZBOX nano BIOS settings of specific functions The ZOTAC ZBOX nano has specific functions that can be enabled or disabled in the BIOS settings such as LED indicator USB 2 0 charging and integrated IR receiver How to disable the ring LED indicator 1 Turn on the ZBOX nano mini PC then press lt Delete gt to enter the BIOS SETUP UTILITY 2 Use the arrow keys to navigate to the PowerManage menu and select Back Light X Setting Advanced PcHealth Boot Security Save amp Exit Enabled Enabled Enabled D P Disa Enabled wer ON OFF R Device 55 Charge Function Fe Previous iis F9 Optimized Defaults 10 Save 8 Exit 3 4 ZOTAC ZBOX nano Press lt Enter gt and select Disabled x Setting Advanced PcHealth Boot Security Save amp Exit Back Light Disabled 1 General Help 2 Previous Values F9 Optimized Defaults
10. ZBOX nano ships with a remote control Follow the instructions below to use the remote control Function keys e Ei RECORD PAUSE STOP START BACK INFORMATION 4 DOWN LEFT RIGHT 4 DP REW PLAY FWD REPLAY SKIP Shortcut Buttons 1 2 3 amp I 5 6 GUIDE SLEEP 7 8 9 0 Audio and Video Buttons VOLUME MUTE CHANNEL UP DOWN UP DOWN D RED GREEN YELLOW BLUE Note Some remote control functions listed above are only available with select applications You are unable to use these functions if the software is not compatible with the remote The ZOTAC ZBOX nano 15 designed to meet Windows Media Center standards The MCE remote control is compatible with Windows 7 Media Center 20 ZOTAC ZBOX nano Lithium Battery installation 1 Locate the arrow the rear cover of the remote control and push the cover as desginated by the arrow 2 Remove the rear cover and insert the CR2032 lithium batteries into the battery jar at a 45 degree angle 3 Gently press down on the CR2032 lithium batteries and reinstall the rear cover 21 ZOTAC ZBOX nano Installing drivers and software Installing an operating system The ZOTAC ZBOX does not ship with an operating system preinstalled The user must install the operating system before the ZOTAC ZBOX can be used The following operating systems are supported e Win
11. dows 7 e Windows 8 Follow instructions below to install an operating system Attach external DVD drive via USB Insert disk for operating system Wait for the ZOTAC ZBOX nano to boot from the disk Follow the onscreen directions to install the operating system Install system drivers to gain full functionality of the ZOTAC ZBOX hardware and features Note For best compatibility please only use the eSATA or USB 2 0 ports as the OS installation source drive connection Installing system drivers Before you can use the full features of the ZOTAC ZBOX nano the system drivers must be installed The following types of operating systems are supported by the ZOTAC ZBOX nano driver DVD e Windows 7 e Windows 8 Follow the instructions below to install the system drivers 1 Insert the ZOTAC ZBOX nano driver DVD If autorun is enabled the driver installation main menu will show up automatically Note If autorun is disabled you can click the file Launch EXE to bring up the driver installation main menu 2 The following drivers are available on the DVD Intel Chipset Driver HDA Sound Driver e Intel Graphics Driver Ethernet PCI E Driver USB 3 0 Controller Driver Wireless Network Driver Intel Management Engine CIR Driver Bluetooth Driver MassStorage Driver 22 ZOTAC ZBOX nano USB Charger optional Note If you want to use USB charger for iPhone iPad please install the driver at X
12. erties nunt ote aah Use the following DNS server addresses ed ai He pends nee De inis 4 Select Use the following IP address ism 5 Enter your IP address subnet mask and Default gateway 6 Enter the preferred DNS server address ifi necessary 7 After entering all of the related values click OK to finish the configuration 23 ZOTAC ZBOX nano Using a dynamic IP PPPoE connection 1 Repeat Step 1 3 in the previous section 2 Select Obtain an IP address automatically and click 3 Click Create new connection to start the NEW Connection Wizard 4 Click Next 5 Select Connect to the Internet and click Next 6 Select Set up my AW connection manually Conte ot Ha 7 Select your connection AD type and click Next o 8 Enter your ISP Name and NNNM click Next p eg 9 Enter your User name and mee Password Click Next NI ed 10 Click Finish to finish the sean so ptm configuration 11 Enter your user name and password Click Connect to connect to the internet Note Contact your internet Service Provider ISP if you have problems connecting to the network Configuring audio output via an HDMI device Follow the steps below to enable audio output via HDMI when connecting the ZOTAC ZBOX nano to a TV or receiver via HDMI
13. es connectivity with digital audio receivers and speakers for crystal clear digital audio and surround sound from compatible soundtracks USB 2 0 ports The USB Universal Serial Bus ports are compatible with USB devices such as keyboards mice cameras and hard disk drives Microphone jack The microphone jack is designed to connect a microphone for video conferencing voice narrations or simple audio recordings Note 1 The power adapter may become warm to hot when in use Do not cover the adapter and keep it away from your body Note 2 Due to the unique tool less customizable design some connectors are placed upside down ZOTAC ZBOX nano Rear view Refer to the diagram below to identify the components on this side of the system 1 Power input DC19V The supplied power adapter converts AC power to DC power for use with this jack Power supplied through this jack supplies power to the mini PC To prevent damage to the mini PC always use the supplied power adapter 2 HDMI output The HDMI High Definition Multimedia Interface output supports Full HD 1080p displays such as an HDTV or monitor 3 DisplayPort The DisplayPort output supports displays with resolutions up to 2560x1600 4 USB 3 0 ports The USB 3 0 port supports the SuperSpeed USB 3 0 devices and is backwards compatible with USB 2 0 1 1 devices Use this port for USB 3 0 devices for maximum performance with USB 3 0 compatible devices 5 Ethernet port The eight pin
14. g the power adapter or switch off the AC outlet to conserve power ZOTAC ZBOX nano Positioning the ZOTAC ZBOX nano Do not position the ZOTAC ZBOX where the ventilation holes are covered To guarantee proper use leave 4 inches 10 cm of spacing in front of the ventilation holes ZOTAC ZBOX nano mini PC systems provide ample connectivity in a tiny form factor please choose connectors and cables in appropriate sizes to avoid interference Mounting the ZOTAC ZBOX nano to a LCD monitor You can attach your ZOTAC ZBOX to the back of a VESA75 100 compliant monitor 1 Secure the VESA mount to the LCD monitor using 4 screws not included Disclaimer ZOTAC cannot be held liable for damages resulting from an improper installation 2 Align the ZOTAC ZBOX mounting holes to the VESA mount attachment pegs Attach the ZOTAC ZBOX to the VESA mount and gently press down to secure the ZBOX to the mount ZOTAC ZBOX nano 3 Connect the ZOTAC ZBOX nano to your LCD monitor with an HDMI DP cable IR receiver Users can control compatible applications with the integrated IR receiver or included external USB IR receiver 1 Integrated IR receiver Note Please install CIR driver from DVD before using the integrated IR receiver Integrated IR receiver 2 External USB IR receiver please connect the external USB IR receiver to a USB 2 0 port External USB IR receiver 19 ZOTAC ZBOX nano Remote control optional The ZOTAC
15. ller and select Disabled ain xX Setting PcHealth PowerManage Boot Security Save amp Exit CIR Controller Enabled Realtek Ethernet Controller Configuration CIR Controller Disabled ct Item ick Select F1 General Help F2 Previous Values F9 Optimized Defaults 10 Save 8 Exit JESC Right Click Exit Enabled enable the internal IR receiver default Disabled disable the internal IR receiver 3 Press F10 to save the configuration and exit 11 ZOTAC ZBOX nano Customizing the ZOTAC ZBOX nano Before installing hardware please follow the instructions below to remove the cover of your ZOTAC ZBOX 1 Remove the four screws securing the bottom cover into place 2 Locate side with engraving that says Pull Upward Pull upward on the cover as shown below ZOTAC ZBOX nano Installing a memory module 1 Locate the SO DIMM memory slot and insert a SO DIMM memory module into the slot at a 45 degree angle 2 Gently press down on the memory module until it locks into place by the arms of the memory slot ZOTAC ZBOX nano Installing a hard disk 1 Locate the hard disk bracket remove the 2 screws and remove the hard disk bracket as shown in the image below 3 Insert the hard disk into the socket and gently slide into the connector 14 ZOTAC ZBOX nano 4 Reinstall the screws for the hard disk bracket Connecting a S PDIF cable 1 Connect the S PDIF cable to the mini
16. lowing illustration displays the package contents of your new ZOTAC ZBOX nano Please contact your retailer If any of the below items are damaged or missed Package contents 1x ZOTAC ZBOX nano mini PC e 1x ZOTAC VESA mount 4 x Mount screws e 1 x AC Adapter e 1 x Power Cord 1 x Headphone SPDIF adapter e 1x External USB IR receiver 1xWiFi antenna e 1 x Remote Control e 2x CR2032 Lithium Cells e 1 x User Manual 1 x Quick Start Guide 1x Support DVD ZOTAC ZBOX nano Getting to know your ZOTAC ZBOX nano Front view Refer to the diagram below to identify the components on this side of the system 1 2 Power switch The power switch turns the mini PC ON and OFF HDD status indicator The hard disk LED blinks when data is being written onto or read from the hard disk drive WiFi status indicator The WiFi LED blinks when data is being transfered over WiFi IR receiver The IR receiver is used to receive signals from the IR remote control Memory card slot The built in memory card reader reads and writes MMC SD SDHC MS MS Pro xD SDXC cards used in devices such as digital cameras MP3 players mobile phones and PDAs Headphone mini Optical S PDIF jack The headphone mini Optical SPDIF jack 3 5mm is used to connect the system s audio output to amplified speakers or headphones It supports mini Optical S PDIF output with the included mini Optical S PDIF adapter The optical S PDIF output enabl
17. system on a stable surface with the provided stand Never use the system alone without the stand Openings on the chassis are for ventilation Do not block or cover these openings Make sure you leave plenty of space around the system for ventilation Never insert objects of any kind into the ventilation openings Use this product in environments with ambient temperatures between 0 C and 35 If you use an extension cord please use the UL listed cord and make sure that the total ampere rating of the devices plugged into the extension cord does not exceed its ampere rating Care during use D D Do not walk power allow anything to rest it Do not spill water or any other liquids on your system When the system is turned off a small amount of electrical current still flows Always unplug all power modem and network cables from the power outlets before cleaning the system If you encounter the following technical problems with the product unplug the power cord and contact a qualified service technician or your retailer gt The power cord or plug is damaged gt Liquid has been spilled into the system gt The system does not function properly even if you follow the operating instructions gt The system was dropped or the cabinet is damaged gt The system performance changes ZOTAC ZBOX nano Welcome Congratulations on your purchase of the ZOTAC ZBOX nano mini PC The fol
Download Pdf Manuals
Related Search