Anthro Display Cart
Contents
1. 17 18 19 Cabinet Not shown Cabinet Handle Not shown Handle Fasteners Not shown 1 2 Button head Screw Not shown 8 Quantity Part Number 1 225 A310 05 03 00 2 125 5377 00 175 5310 00 225 4421 00 325 5548 00 1 225 4311 00 575 5073 00 325 5092 00 325 5629 00 280 A304 20 01 00 500 A310 05 01 00 1 175 A302 02 001 03 8 325 5106 00 4 150 5084 00 16 325 5264 00 22 325 5003 00 8 525 5037 00 SREE SS 2 175 5215 00 1 835 5455 00 1 175 A138 10 01 03 2 325 A129 18 01 00 325 5196 00 TOOLS These tools are S provided for this assembly i 5 32 hex ball end driver 5 32 hex driver bit 3 16 hex key 5 32 hex key These tools are required but not provided Level Phillips head screwdriver IF YOUR CART HAS A CABINET GO TO STEP 2 IF NOT START WITH STEP 1 STEP 1 CART WITHOUT CABINET Attach the Base to the Legs m Using the Anthro driver install the end caps on the base with 3 4 wood screws m Slide one rubber cable catcher blade into each leg Lay the legs on the floor side by side While one person lifts the base the second person slides one leg into the base rubber blade to the back until it reaches the bottom of the base Attach the leg to the base with four 3 4 Cap Screws using the 3 16 hex key Tighten all the way Repeat for the second leg WN ip ahead to Step 6 ND 3 4 Cap Screw wy 3 4 Wood Screw 325 5264 00 325 51062. 00 Lock all four casters One at a time thread them into the holes in the base Turn them until they re tight With the help of a second person carefully lift the cart upright End Caps D Y ae Rubber Cable Blade Top View STEP 2 CART WITH CABINET Assemble the Cabinet m Using your Phillips screwdriver install the handle onto the cabinet door m Using the Anthro driver remove the four fasteners holding the cabinet s back panel in place Set aside the fasteners and the panel Align one tapped rail with the holes on one of the cabinet s leg channels Using the Anthro driver loosely attach one 1 2 bracket screw through the metal flange on the cabinet and into the tapped rail Tighten just until the tip of the fastener reaches the outside of the tapped rail m Repeat for the other seven rails there are four on each of the two channels Place the cabinet on its back with the lock and handle facing up YD Miso STEP 3 CART WITH CABINET Install the Cabinet m Slide one rubber cable blade into each leg m Slide the legs into the leg channels blades to the back on the cabinet so the tapped rails fit into the slots on the legs Position each leg so it extends 2 3 4 beyond the bottom of the cabinet Use the Anthro driver to tighten the fasteners for the tapped rails STEP 4 CART WITH CABINET Install the Base and Add the Casters m Using the Anthro driver ins
3. ASSEMBLY INSTRUCTIONS Anthro Video Conferencing Cart WELCOME Thank you for purchasing your An thro Video Conferencing Cart If you have any questions or if we can help you in any way please contact us at 800 325 3841 hk ANTHRO Technology Furniture Fast and Friendly Warranty The Anthro Video Conferencing Cart has a Lifetime Warranty Notices Technology Furniture is a trademark of Anthro Corporation Anthro reserves the right to modify the design and specifications without prior notice Part Anthro Video Conferencing Cart DCO2SM BK5 Anthro Video Conferencing Cart w Cabinet DCO1SM BK5 NOTE The Camera Mount is not included Anthro Corporation 10450 SW Manhasset Dr Tualatin OR 97062 Toll free 800 325 3841 Fax 800 325 0045 email sales anthro com anthro com Outside the U S Tel 503 691 2556 Fax 503 691 2409 300 5528 00 July 2011 PARTS LIST Before beginning assembly of your Video Conferencing Cart please review the parts list to verify that your shipment is complete Product 01 02 15 Top Plate Handle Assembly Handle Bar Foam Handle Wrap Handle Bracket 1 3 4 Flat head Screw Monitor Mount Back Bracket Telehook Assembly Workstation Screw Flat Fender Washer Legs 50 long Base End Caps 3 4 Screws 5 Locking Casters 3 4 Cap Screws 1 2 Button head Screw Tapped Rails Rubber Cable Blade 50 Not shown CABINET COMPONENTS 16
4. ly with two 1 2 button head screws using the Anthro driver Tighten just until the tip of the fastener reaches the outside of the tapped rail Repeat for the second handle m Slide each handle assembly onto the cart legs until the top of the handle is 41 above the floor and tighten Repeat for the second handle ey one oe STEP 7 Install the Monitor Mount and Top Plate m Locate the monitor mount back bracket Loosely attach four tapped rails to the back of the bracket with eight 1 2 button head screws using the Anthro driver m Slide the back bracket onto the extrusions so the bracket is at the front of the cart Slide it down until it is just above the handle and loosely attach Align the top plate with the top of the extrusions Attach the top plate to the extrusions with eight 3 4 Cap Screws using the 3 16 hex key m Slide the monitor mount back bracket up to the desired height Make sure it s level then tighten its fasteners m The Telenhook Mount assembly is packaged in its own box Open that box and locate the Wall Plate m Using the Anthro driver attach the wall plate to the back plate using four Workstations Screws and four flat fender washers Follow the Telehook instructions to attach the brackets Bee to your display and then to attach the display to the Wall Plate m Slide the Security Bracket into place and
5. secure using two 1 2 button head screws and two nylock nuts For added security use your own padlock with 3 16 dia shackle instead COD yume ala Cap Screw Sy ee CONGRATULATIONS YOUR CART ASSEMBLY IS COMPLETE 4 Questions Call us at 800 325 3841 or visit anthro com We re happy to walk you through the assembly
6. tall the end caps on the base with 3 4 wood screws m Elevate the cabinet a few inches off the floor Use some of the packing materials included in your shipment m Align the base with the legs Make sure that the long extensions on the base will be under the door of the cabinet That s the front of the cart m Using the 3 16 hex key secure the base to the legs with eight 3 4 Cap Screws four for each side Tighten all the way m Lock all four casters One at a time thread them into the holes in the base Turn them until they re tight m With the help of a second person carefully lift the cart upright STEP 5 CART WITH CABINET Secure the Cabinet Reinstall Back Panel m Use your level to verify that the cabinet is level Use your Anthro driver to loosen the fasteners holding the tapped rails and adjust the cabinet until it is level m Tighten all the fasteners for the tapped rails m Using the Anthro driver reinstall the back panel Make sure that the cord wraps are on the outside of the cabinet and the cord pass throughs are at the bottom Rubber Cable Blade Top View Vv Ne 3 cap Sr Anthro Video Conferencing Cart Assembly Instructions STEP 6 Install the Cart Handles m Ifyou are including an Additional Shelf in this assembly install it now using its instruction m Loosely attach two tapped rails to each handle assemb
Download Pdf Manuals
Related Search