Vogel's PFW 6851 Display wall mount - turn & tilt, 80 kg
Contents
1. flat panel Step 3 Using a screwdriver insert and tighten the mounting hardware and adapter plates to the back of the flat panel Do not over tighten the Adapter Plate screws Griplate Mounting Hardware Flat Panel Step 4 Place the universal mounting brackets over the threaded mounting studs that are on the adapter plate Step 5 Place one 1 5 16 flat washer onto each threaded mounting stud Step 6 Thread one 1 M8 nylon nut onto each threaded mounting stud Adapter Plate A vor Before tightening the nylon nut be sure that both universal mounting brackets are POEKNA level and aligned with each other If they are not aligned and level the flat panel will not sit properly when mounted to the PFW 6851 Step 7 Once the universal mounting brackets are level l gt APOIAN use a 1 2 socket and socket wrench to tighten Flat Washer the M8 nylon nuts Do not over tighten the Universal Mounting SCrews Bracket Installation Instructions Page 11 agers professional PEW 6 8 5 1 Attaching the Flat Panel to the Wall Plate A caution Two people are required for this step Ay warninc Do not release the flat panel until verifying the connection between the universal mounting brackets and the upper and lower mounting bars e ff Upper Mounting ra Bar Oy mS Lower Mounting Bar Fla2. tighten the lag bolt at this time Step 10 Re level the PFW 6851 Step 11 Using a 1 2 socket wrench completely tighten the two 2 upper lag bolts A warning DO NOT over tighten lag bolts when attaching the mount to the wall Improper installation may result in personal injury or damage to property A A minimum of two 2 wall studs must be used in the installation of this product Repeat these steps to secure the lower mounting channel to the wall note There will be a total of four 4 mounting points 2 for the upper mounting channel and 2 for the lower mounting channel A wore if the studs are 12 304 8mm apart use three 3 76 2mm lag bolts for the upper mounting channel and three 3 76 2mm lag bolts for the lower mounting channel If the studs are 16 406 4mm 18 457 2mm or 24 609 6mm apart use two 3 lag bolts for the upper mounting channel and two 3 lag bolts for the lower mounting channel Page 6 Installation Instructions Wagers professional PEW 6 8 5 1 Concrete Surface Installation Ay warninc THE FOLLOWING STEPS MUST BE PERFORMED BY TWO PEOPLE A wore lf concrete wedge anchors are not used as described in these installation instructions and you decide on other mounting hardware please follow the installation instructions as provided with that hardware Step 1 Determine the desired viewing location Step 2 Place the mount into position against the wall and level the m
3. AN BE USED WITH THIS PRODUCT IS 79 KG PROPER INSTALLATION PROCEDURE BY A QUALIFIED SERVICE TECHNICIAN AS OUTLINED IN THE INSTALLATION INSTRUCTIONS MUST BE ADHERED TO FAILURE TO DO SO COULD RESULT IN SERIOUS PERSONAL INJURY OR EVEN DEATH SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE ASSEMBLY OF THIS PRODUCT USE PROPER SAFETY ay GEAR AND TOOLS FOR THE ASSEMBLY PROCEDURE TO PREVENT PERSONAL INJURY At least two qualified people should perform the assembly procedure Injury and or damage can result from dropping or mishandling the flat panel If mounting to studs make sure that the mounting screws are anchored into the center of the studs Use of an edge to edge stud finder is recommended Be aware of the mounting environment If drilling and or cutting into the mounting surface always make sure that there are no electrical wires in wall Cutting drilling into an electrical line may cause serious injury POO Make sure there are no water lines inside the wall where the mount is to be located Cutting drilling into a water line may cause severe water damage to the mounting surface This product is intended for indoor use only Use of this product outdoors could lead to product failure and personal injury Do not install near sources of high heat Do not install on a structure that is prone to vibration movement or chance of impact Page 2 Installation Instructions wogel s Wdger s PEW 6851 Parts List Ext
4. e flat panel Place the other hand on the center bottom edge of the flat panel Using the upper hand gently pull the top of the flat panel away from the wall while the lower hand gently pushes the bottom of the flat panel towards the wall Plastic Channel Cover Installation Step 1 Step 2 Place the plastic channel covers over the mounting plate 2 side covers and 1 center cover Gently push each cover into place covering the mounting slots of the mounting plate A wore Repeat steps and 2 for the installation of the lower plastic channel covers Installation Instructions Side Cover Long PFW 6851 Tension Bolt Adjusting the Flat Panel Up Step 1 Step 2 Step 3 Center Cover Short Place one hand at the center top edge of the flat panel Place the other hand on the center bottom edge of the flat panel Using the upper hand gently push the top of the flat panel towards the wall while the lower hand gently pulls the bottom of the flat panel away from the wall Side Cover Long Page 13 eger s professional PEW 6 8 5 1 Technical Specification All measurements are in inches mm 25 71 26 4 653 671 2 Page 14 Installation Instructions
5. ension Adapter Hardware Pack O O O O a O 6 O o Nae Nae aa 5 16 Flat Washers Griplate Qty 6 Qty 4 Qty 4 Thread Depth Universal Indicator Qty 1 Spacers Qty 24 Channel Covers Qty 6 Installation Tools not supplied 1 2 Socket and Socket Wrench Installation Instructions Page 3 o 5 professional Kr M4 x 30mm Qty 6 ogy M4 x 25mm Qty 6 KE M4 x 16mm Qty 6 eddd Page 4 M6 x 45mm Qty 6 M6 x 30mm Qty 6 M6 x 25mm Qty 6 M6 x 16mm Qty 6 M5 x 30mm Qty 6 M5 x 25mm Qty 6 M5 x 16mm Qty 6 M8 x 70mm Qty 4 M8 x 45mm Qty 6 M8 x 30mm Qty 6 M8 x 25mm Qty 6 M8 x 16mm Qty 6 PFW 6851 Installation Instructions professional PEW 6851 Wood Stud Installation warni THE FOLLOWING STEPS MUST BE PERFORMED BY TWO PEOPLE a Wall Stud Electronic Stud Finder Step 2 Once the studs have been located use a pencil Step 1 Determine the desired viewing location Use a to mark the center of each stud stud finder to locate two studs closest to the viewing location A vor A minimum of two 2 wall studs must be used in the installation of this product y Upper Mounting t Wall Stud Channel Mounting Slot Flat Washer 5 16 Lag Bolt 1 4 Drill Bit 1 2 Socket Wrench A vor Wo people must perform the installat
6. hpick 1 8 above the depth of the threaded insert as shown in Figure 1 O Insert the small straw or toothpick into the remaining threaded inserts to compare and verify their depth using the straw or toothpick s 1 8 allowance mark Locate the correct diameter screw for the threaded insert If the screw you selected is longer than the 1 8 allowance mark on the small straw or toothpick as shown in Figure 2 and Figure 3 do not use this screw The screw length must not bypass the mark O Test each size of the screws provided The correct screws should thread easily into the mounting point and not pull out when tension is applied You must account for the bracket spacers and Griplate depths when using the Thread Depth Indicator to measure the thread depth of your flat panel AN PFW 6851 Level Threaded Shaft Nut 1 2 Socket wore lf concrete wedge anchors are not used as described in these installation instructions and you decide on other mounting hardware please follow the installation instructions as provided with that hardware Marking the 1 8 Allowance Marking the Depth Threaded Insert Small Straw or Toothpick Figure 2 Small Straw Depth Plus 1 8 Allowance Small Straw or Toothpick Depth Plus 1 8 Allowance or Toothpick Mark Page 8 ogere professional PEW 685 1 Universal Spacers Installation optional A v
7. ion One person must hold the mount while the other person levels the mount The mount must remain in place while the mounting hardware is tightened A When determining viewing height the center of the TV should be at eye level while sitting in Step 4 Level the mount an upright position When using the flat panel Step 5 Align the mounting slot with the drilled hole as room decoration raise it to the point where Step 6 Insert and tighten one 1 5 16 x 3 lag bolt and the bottom of the screen is at eye level while flat washer Tighten using a 1 2 socket sitting and the top is eye level when standing wrench Do not completely tighten the lag bolt at this time Step 3 Drill a pilot hole at the marked location using a power drill and a 1 4 drill bit A warning DO NOT over tighten lag bolts when A warns Only use 1 4 drill bit when drilling the a eee Me EE i a pilot holes i ae damage to property Installation Instructions Page 5 o 5 rofessional PFW 6851 Mounting Slot Flat Washer Upper Mounting Channel 5 16 Lag Bolt 1 2 Socket Wrench A vor Before drilling the second mounting hole re level the mount Step 7 Drill a pilot hole at the marked location using a power drill and a 1 4 drill bit Step 8 Align the mounting slot with the drilled hole Step 9 Insert and tighten one 1 5 16 x 3 lag bolt and flat washer Tighten using a 1 2 socket wrench Do not completely
8. irsssrerrsrerrrrrrerrrrrrrrrrrrre 11 Attaching th Flat Panel tothe Wai oaceeceree acces intre ngoentcndecanseeiauenuse Ene eai Taa EEEa 12 Sec rine aud Leveling the Flat Pang leesniirearitpeierintnideninn kn NESEN a EEEE 12 Poise the Fla Panel Tieso ene EEEE r O E E EE EEEE AE EE EAEE 13 Plastic Channel Cover Installation 000000 0c ccc cece ec ecececeeeceeceseeeceseuseeuceseusssecuseueseeusesestseneneess 13 Technical Specifica ONS xc rcacerqennpconctantqusdendseahansead Ea EEA EEOSE EEE ANAE 14 VY AI AL OY ss sarees neoinean E EEEE AA E E EE RE tants 15 Warning Statements PRIOR TO THE INSTALLATION OF THIS PRODUCT THE INSTALLATION INSTRUCTIONS SHOULD BE READ AND PD comecerey UNDERSTOOD THE INSTALLATION INSTRUCTIONS MUST BE READ TO PREVENT PERSONAL INJURY AND PROPERTY DAMAGE KEEP THESE INSTALLATION INSTRUCTIONS IN AN EASILY ACCESSIBLE LOCATION FOR FUTURE REFERENCE VOGELS DOES NOT WARRANT AGAINST DAMAGE CAUSED BY THE USE OF ANY VOGE S y PRODUCT FOR PURPOSES OTHER THAN THOSE FOR WHICH IT WAS DESIGNED OR DAMAGE CAUSED BY UNAUTHORIZED ATTACHMENTS OR MODIFICATIONS AND IS NOT RESPONSIBLE FOR ANY DAMAGES CLAIMS DEMANDS SUITS ACTIONS OR CAUSES OF ACTION OF WHATEVER KIND RESULTING FROM ARISING OUT OF OR IN ANY MANNER RELATING TO ANY SUCH USE ATTACHMENTS OR MODIFICATIONS THE SURFACE MUST BE CAPABLE OF SUPPORTING AT LEAST FIVE TIMES THE WEIGHT OF THE FLAT PANEL IF NOT THE y STRUCTURE MUST BE REINFORCED THE MAXIMUM WEIGHT THAT C
9. o PaA Je vogels eo professional PFW 6851 Display Wall Mount Turn amp Tilt 80 kg INSTALLATION INSTRUCTIONS 9531 007 Z00 01 ogor professional PEW 685 1 Table of Contents Warning Statements 0d vndcrssnsuava ateoiteawedeavenenia endvedeyiobadoadcslenveavieeee anne aleni lt aninapinetvecteas seaunebendss 2 Parie Loi eeaeee AEA EEE EEA EEEE EENE 3 Installation EOS cap cas corer eee sence area eee screed eee anne nDA a ENAREN EREE NEEE RE EPEE a i ERT aa EE IT Rie 3 Wood Stud Installation oscncnucacesstiesdeconnpsaneensav denwesawendcnasp tas papeslaaddevenaavesesiusia Seneoctadsenaasmbeeaiens 5 Concrete Surface INS ta A O8 peicoinasuscapnsdynsdeaveuscecswnesencamesadeeaeyehvebludapuinnniaidseda men EErEE EEE EEE EEEE Ereren 7 Determining the Mounting Hardware eeeeeeieeeeiireseeireresrirrrstriersstrirrssritrssrirrsrrrrrrorrrrrni 8 Universal Spacer Installation cc cscviavatsieeueiatasrsasnvendasvaemsectonwonseaseniaasosusnectinnnasseoetasiesinnarvorses 9 Oe US ered page EI EE E EIE ce gece api E NA A E 9 Mounting Bracket Installation cserreesicasecssererciersredrirssres arenar ed Errn a E ARR EAEN 10 Adapter Plate Installation optional es seeeeiseessiiesssiiesssrierssreessreerssr
10. om lf your flat panel has uneven mounting points or recessed mounting points please use the provided universal spacers oRoR oR OR OR OR ORO OROROROR OR OR OR OR OROROR The universal spacer may be stacked six 6 high for a total stacking height of 1 1 2 The universal spacers must be stacked in the direction shown above The universal spacers must be placed between the mounting bracket and the flat panel The universal spacer will fit M4 M5 M6 and M8 screws sizes Dimples Griplate Installation we The Griplates have M4 M5 M6 and M8 hole patterns to yE fit the hardware that your flat panel requires iii Ea EXAMPLE If your flat panel uses M8 screws use the M8 mounting points DIMPLES FACING UP Pre install the mounting screws universal spacers and Griplates Once mounted push down to eliminate movement from the bracket then tighten the rest of the hardware Repeat this process for the installation of the remaining mounting bracket DIMPLES FACING UP oZ 4 Faas FACING DOWN Installation Instructions Page 9 Yegers professional PEW 685 1 Mounting Bracket Installation This kit provides a variety of screws with different lengths and diameters to accommodate most flat panels A note The number and location of mounting points will vary between manufacturers A warme Do NOT over
11. ount Step 3 Mark off four holes to be used for securing the mount Mark Level Ar When determining viewing height the center of the TV should be at eye level while sitting in an upright position When using the flat panel as room decoration raise it to the point where Concrete Wedge Anchor the bottom of the screen is at eye level while sitting and the top is eye level when standing Step 4 Next drill holes using a masonry bit commercially available for your anchors Step 5 Insert a commercially available concrete anchor into each hole Step 6 Use a hammer and lightly tap each anchor into place so that only the threaded shaft of the concrete wedge anchor is protruding from the wall Drill Threaded Shaft Hammer Installation Instructions Page 7 e 5 lt Gagel S professional Step 7 Once all of the anchors are in place move the wall bracket into position Attach the nut onto the threaded shaft that is protruding from the wall Re level the wall plate and tighten all concrete wedge anchor nuts at this time Step 8 Step 9 A warna Do NOT over tighten the concrete wedge anchors Determining the Mounting Hardware Insert a small straw or toothpick into the threaded inserts found on the back of the flat panel Use a pencil to mark the depth of the threaded insert on the small straw or toothpick Mark the straw or toot
12. t Panel Step 1 Place the universal brackets and the flat panel over and onto the upper and lower mounting bars of the PFW 6851 and lower it down Do not release the flat panel until the flat panel is resting securely on the upper and lower mounting bars Securing and Leveling the Flat Panel A vorp 0 the event that the flat panel Screwdriver is tilted too far to one side the leveling screws will allow you to compensate for this tilt by Leveling simply adjusting the screws Screw with a _ screwdriver see illustration to the right for a clearer view Pre installed Step 1 Use a screwdriver to adjust the uN SS two 2 M6 x 30 leveling screws located on the top of the mounting brackets YNV N Step 2 Once the flat panel is level use a screwdriver to tighten the two 2 M6 x 30 locking screws located on the bottom of the mounting brackets Do not over tighten these screws Locking Screw Pre installed Page 12 Installation Instructions vogel s Ye professional Adjusting the Flat Panel Tilt A vorm LO ADJUST THE TILT TENSION OF THE PFW 6851 LOOSEN THE TENSION BOLTS LOCATED ON THE BOTTOM RIGHT AND LEFT SIDE OF THE MAIN ARM ASSEMBLY RE TIGHTEN THESE BOLTS TO ACHIEVE YOUR DESIRED TENSION Tension Bolt Adjusting the Flat Panel Down Step 1 Step 2 Step 3 Place one hand at the center top edge of th
13. tighten the screws a P Png SSS Mounting Hardware P ng lt Mounting Bracket Je Griplate Mounting Point Universal Spacer Flat Panel Step 1 Place your flat panel screen down on a soft flat surface and locate the threaded mounting points that are located on the back of the flat panel Step 2 Determine which screw is the correct length please see Determining the Mounting Hardware section Step 3 Attach each bracket to the flat panel by aligning the holes on each bracket with the threaded inserts on the back of your flat panel insert the screws through both and turn clockwise until they are fully inserted Page 10 Installation Instructions ogere professional PEW 685 1 Adapter Plate Installation optional A note The adapter plates can be used with mounting patterns from 200mm x 200mm to 650mm x 840mm yore I the event that your flat panel has recessed or an uneven mounting surface universal spacers may be stacked to achieve proper spacing Select the amount of universal spacer s that is closest in depth to keep your adapter plate as close to the flat panel as possible The universal spacer must be secured between the flat panel and the adapter plates AX warnine Do NOT over tighten the screws Step 1 Determine if your flat panel will need the adapter plates Step 2 Locate the mounting points on the back of the
Download Pdf Manuals
Related Search