Elo Touch Solution 1523L
Contents
1. After accepting the end user license agreement the drivers will finish installing Reboot your computer after the install is complete eS e l TOUCH User Manual 1523L 1723L SOLUTIONS SW601951 Rev A Page 10 of 29 Chapter 3 Mounting Rear VESA Mount For the 15 inch touchmonitor a four hole 75x75mm mounting pattern for M4 screws is provided on the rear of the monitor Remove the stand using a Phillips screwdriver to access this mounting interface The VESA FDMI compliant counting is coded VESA MIS B 75 C M4 THREAD KENSINGTON LOCK MAX SCREW LENGTH RECEPTICAL fmm FROM MOUNTING SURFACE 4 User Manual 1523L 1723L SW601951 Rev A Page 11 of 29 For the 17 inch touchmonitor a four hole 75x75mm mounting pattern for M4 screws is provided on the rear of the monitor Remove the stand using a Phillips screwdriver to access this mounting interface The VESA FDMI compliant counting is coded VESA MIS B 75 C M4 THREAD L KENSINGTON LOCK MAX SCREW LENGTH RECEPTICAL 7mm FROM MOUNTING SURFACE x4 User Manual 1523L 1723L SW601951 Rev A Page 12 of 29 Base Mount For the 15 inch touchmonitor a threaded three hole mounting pattern for M4 screws is provided on the bottom of stand base for mounting or securing 196 aie a hia THREAD GABLE HOLE MAX SCREW LENGTH Timm FROM MOUNTING a a 7 im ej l 39 5 CABLE HOLE 174 7 126 4 For the 17 inch touchm2. Parameter Available Adjustment Brightness Increase decrease monitor brightness Default Maximum Contrast Increase decrease monitor contrast Default Best gray shade performance Clock Allows fine adjustments of the panel s pixel dot clock Only applicable for VGA input video Phase Allows fine adjustments of the panel s pixel dot clock phase Only applicable for VGA input video Automatically adjusts the system clock to the input analog VGA video signal affecting Auto Adjust the H position V position Clock and Phase menu items Only applicable for VGA input video Moves the image horizontally on the display in single pixel increments H position Default Centered Only applicable for VGA input video Moves the image vertically on the display in single pixel increments V position Default Centered Only applicable for VGA input video Switches the scaling method between Full Scaling and Maintain Aspect Ratio Default Full Scaling Full Scaling scales the X and Y dimensions of the input video up or down as needed to the display s native resolution Fill To Aspect Ratio Assuming a landscape orientation and an input video with aspect Aspect Ratio ratio smaller than 1024 x 768 for the 15 inch or 1280 x 1024 for the 17 inch scales the Y dimension of the input video up or down as needed to the display s Y resolution and scales the X dimension to maintain the input video s aspect ratio and fills the rest of t
3. USER MAN Elo Touch Solutions 1523L and 1723L Touchmonitors SW601951 RevA Copyright 2012 Elo Touch Solutions Inc All Rights Reserved No part of this publication may be reproduced transmitted transcribed stored in a retrieval system or translated into any language or computer language in any form or by any means including but not limited to electronic magnetic optical chemical manual or otherwise without prior written permission of Elo Touch Solutions Inc Disclaimer The information in this document is subject to change without notice Elo Touch Solutions Inc and its Affiliates collectively Elo makes no representations or warranties with respect to the contents herein and specifically disclaims any implied warranties of merchantability or fitness for a particular purpose Elo reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation of Elo to notify any person of such revisions or changes Trademark Acknowledgments Elo logo Elo Touch Solutions IntelliTouch iTouch are trademarks of Elo and its Affiliates Windows is a trademark of Microsoft Corporation User Manual 1523L 1723L SW601951 Rev A Page 2 of 29 Table of Contents Chapter 1 NATO GU CUNT a ccenicctncccnntncntnancnancnendnsntndnenontnsncrantntnbnanantntsbarnencraneibencanintd 4 Chapter 2 Installation 2 0 0 ccc cece ceeeeceee cece eeceeeeesesaceeeeseeeeteteeseteneeees 5
4. Chapter 3 Mounting seit baa sista cts sete las Stns ae staal des dapat bd deans 11 Chapter 4 Operation o oo cece ccceccccececeeceeeeceeeeeaceeeeceeeeeaeesaceseeeseetaeereatens 14 Chapter 5 Technical Support c eee cece ee eececeeceeeeeeeeeeeceeeeeeeeteteetatees 20 Chapter 6 Safety amp Maintenance ccececeeeeeeeceeeeeeeeeeteeeetees 22 Chapter 7 Regulatory Information 0 0 0ccc cece eeeeeeeeeeeeteeeeeteeeeetees 24 Chapter 8 Warranty Information 0 0 0 00 0 cece cece cece ee eeeeeteeeeeeteeeeeees 28 e 0 User Manual 1523L 1723L SW601951 Rev A Page 3 of 29 Chapter 1 Introduction Product Description Your new touchmonitor combines the reliable performance of Elo Touch Solutions touch products with the latest developments in touch technology and display design This combination of features creates a natural flow of information between the user and the touchmonitor This touchmonitor incorporates a 16 2M color active matrix thin film transistor LCD panel to provide high quality display performance Its LED backlight significantly reduces power consumption and eliminates mercury compared to CCFL backlit panels Other features that enhance this LCD monitor s performance are Plug amp Play compatibility on screen display OSD controls and a family of optional peripherals including magnetic stripe reader MSR webcam and radio frequency identification RFID module Precautions Follow
5. with X exemptions were taken according to EU RoHS User Manual 1523L 1723L SW601951 Rev A Page 26 of 29 Explanation of Markings 1 In accordance with the SJ T11364 2006 requirement the electronic information products are marked with the following pollution control logo The Environment Friendly Use Period for this product is 10 years The product will not leak or mutate under normal operating conditions listed below so that the use of this electronic information product will not result in any severe environmental pollution any bodily injury or damage to any assets Operating Temperature 0 40 Humidity 20 80 non condensing Storage Temperature 20 60 Humidity 10 90 non condensing 2 It is encouraged and recommended that this product be recycled and reused according to local laws The product should not be thrown away casually ES V Power Adapter Specifications Electrical Ratings Input 100 240VAC 50 60Hz Output 12VDC minimum 4 16A LPS VI Monitor Specifications Electrical Ratings Input 12VDC 4 16A Operating Conditions Temperature 0 C 40 C Humidity 20 to 80 non condensing Altitude 0 to 3 048m Storage Conditions Temperature 20 C 60 C Humidity 10 to 90 non condensing Altitude 0 to 12 192m User Manual 1523L 1723L SW601951 Rev A Page 27 of 29 Chapter 8 Warranty Information Except as otherwise stated herein or in an order acknowledgment delive
6. Source The monitor continually scans for active video on the VGA and DVI connectors This adjustment selects which of those input ports should be given priority to be displayed The options are VGA Priority DVI Priority Default DVI Priority All touchmonitor adjustments made through the OSD are automatically memorized as soon as they are entered This feature saves you from having to reset your choices every time the touchmonitor is unplugged or powered off and on If there is a power failure the touchmonitor settings will not default to the factory specifications OSD and Power Lockouts Press and hold the Menu and Up buttons for two seconds to enable disable the OSD Locking feature When the OSD Locking is enabled pressing any of the Menu Up Down or Select keys will have no effect on the system Press and hold the Menu and Down buttons for two seconds to enable disable the Power Locking feature When the Power Locking is enabled pressing the power switch will have no effect on the system User Manual 1523L 1723L SW601951 Rev A Page 19 of 29 Chapter 5 Technical Support If you are experiencing trouble with your touchmonitor refer to the following suggestions If the problem persists please contact your local dealer or contact Elo Touch Solutions Customer Service Solutions to Common Problems Problem Suggested Troubleshooting Check that the DC power adaptor is properly
7. 361 4800 Tel 32 0 16 35 2100 Tel 81 45 478 2161 Tel 786 923 0251 301 Constitution Drive Fax 1 650 361 4722 Fax 32 0 16 35 2101 Fax 81 45 478 2180 Fax 305 931 0124 Menlo Park CA 94025 customerservice elotouch com elosales elotouch com www tps co jp www elotouch com ar Copyright 2012 Elo Touch Solutions Inc All rights reserved e 0 User Manual 1523L 1723L SW601951 Rev A Page 29 of 29
8. EE This product should not be disposed of with household waste It should be X deposited at a facility that enables recovery and recycling e 0 User Manual 1523L 1723L SW601951 Rev A Page 23 of 29 Chapter 7 Regulatory Information I Electrical Safety Information Compliance is required with respect to the voltage frequency and current requirements indicated on the manufacturer s label Connection to a different power source than those specified herein will likely result in improper operation damage to the equipment or pose a fire hazard if the limitations are not followed There are no operator serviceable parts inside this equipment There are hazardous voltages generated by this equipment which constitute a safety hazard Service should be provided only by a qualified service technician Contact a qualified electrician or the manufacturer if there are questions about the installation prior to connecting the equipment to mains power ll Emissions and Immunity Information Notice to Users in the United States This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interfe
9. all warnings precautions and maintenance as recommended in this user manual to maximize the life of your unit to ensure user safety and to prevent risks See the Safety amp Maintenance chapter for more information This manual contains information that is important for the proper setup and maintenance of the unit Before setting up and powering on your new touchmonitor read through this manual especially the Installation Mounting and Operation chapters User Manual 1523L 1723L SW601951 Rev A Page 4 of 29 Chapter 2 Installation Unpacking the Touchmonitor Open the carton and verify that the following items are present e Touchmonitor with removable protective sheet for its face eUser Manuals CD e Japanese language regulatory information pamphlet eQuick Install Guide eVGA cable eDVI cable eUSB cable eAudio cable eAC DC power adaptor eNorth American power cable eEuropean power cable User Manual 1523L 1723L SW601951 Rev A Page 5 of 29 Stand Positions The stand of the touchmonitor can be converted between two positions the low profile hostess position and the high profile upright position The touchmonitor ships in the low profile hostess position Low profile hostess position e 0 AEON User Manual 1523L 1723L SULU HUNS SW601951 Rev A Page 6 of 29 To convert the stand into the high profile upright position secure the thumbscrews into the high or H
10. ariations in video graphic card outputs may require user adjustments through the OSD to optimize the quality of the touchmonitor s displayed image These adjustments are remembered by the touchmonitor Also to reduce the need for adjustments for different video mode timings the monitor correctly scales and displays some of the video industry s most common video timing modes Refer to the technical specifications for this monitor at http Awww elotouch com for a list of these Preset Video Modes On Screen Display OSD Four OSD buttons are on the bottom of the monitor These can be used to adjust various display parameters User Manual 1523L 1723L SW601951 Rev A Page 16 of 29 MENU lt 4 gt SELECT l The buttons and their functionality are Button Function when OSD is not displayed Function when OSD is displayed Menu Display OSD main menu Return to previous OSD menu 4 Display OSD Brightness submenu Decrease value of selected parameter select previous menu item gt Display OSD Contrast submenu Increase value of selected parameter select next menu item Select Auto Adjust Select parameter for adjustment select submenu to enter eS User Manual 1523L 1723L SW601951 Rev A Page 17 of 29 The OSD buttons control an on screen graphical user interface which displays on top of your input video This allows for intuitive adjustment of the following display parameters
11. chmonitor it uses Windows HID drivers The drivers for the Windows 7 and XP systems are available on the Elo Touch Solutions website Visit www elotouch com for e The most up to date touch driver versions eAdditional touch driver information eDetailed touch driver installation guides e Touch drivers for other operating systems User Manual 1523L 1723L SW601951 Rev A Page 8 of 29 Select the applicable driver from the Elo Touch Solutions website and download Elo Touch Solutions Driver and file downloads Windows Internet Explorer J amp J BID http elotouch com Support Downloads dnid asp B 4 i File Edit View Favorites Tools Help i Favorites BID Elo Touch Solutions Driver and file downloads im EER EG Worldwide e TOUCH maa a SOLUTIONS Products hdi Home gt Support gt Downloads gt Solutions Driver and File Downloads Technologies Subscribe to The Touch Monitor the Elo email newsletter for information on the latest driver releases Les Support Help with downloads Help with identifying your touch technology How To Buy pis Archived unsupported drivers are available on this paqe Partners F Windows XP Pro operating system licensing will be valid through 2016 on Elo TouchSystems products As well as offering additional new OS options support of Windows XP will continue up to 2016 lt About Elo The Acoustic Pulse Recognition APR and Projected Capaciti
12. connected Verify the DC power adaptor is functioning Use the OSD to increase the brightness Use the OSD to increase the contrast If the Power Status LED is blinking the monitor or Computer Module may be in SLEEP mode Press any key move the mouse touch the Touchscreen to see if the image reappears Check that the signal source device is turned on Check that that there are no loose cable connections Adjust your computer s resolution timing mode to be within the allowable timing ranges specified for your touchmonitor see website for specifications Adjust your computer s resolution timing mode to be within the allowable timing ranges specified for your touchmonitor see website for specifications Use the Auto Adjust function in the OSD Verify your PC has the latest Elo drivers installed Touch functionality doesn t work Perform the calibration routine provided with the latest Elo drivers The OSD buttons or power button does not Check to see if the OSD lock or power lock functions respond when pressed are on The touchmonitor does not respond when turning on the system Monitor display is dim Monitor display is blank Monitor displays an Out Of Range message Monitor display image looks abnormal e 0 User Manual 1523L 1723L SW601951 Rev A Page 20 of 29 Technical Assistance Visit www elotouch com products for technical specifications for this device Visit www elotouch c
13. ental damages Buyer assumes the risk and agrees to indemnify Seller against and hold Seller harmless from all liability relating to i assessing the suitability for Buyer s intended use of the Products and of any system design or drawing and ii determining the compliance of Buyer s use of the Products with applicable laws regulations codes and standards Buyer retains and accepts full responsibility for all warranty and other claims relating to or arising from Buyer s products which include or incorporate Products or components manufactured or supplied by Seller Buyer is solely responsible for any and all representations and warranties regarding the Products made or authorized by Buyer Buyer will indemnify Seller and hold Seller harmless from any liability claims loss cost or expenses including reasonable attorney s fees attributable to Buyer s products or representations or warranties concerning same e 0 User Manual 1523L 1723L SW601951 Rev A Page 28 of 29 Check out Our Website www elotouch com Get the latest eProduct Information eSpecifications eNews on upcoming events ePress releases eSoftware drivers e TouchMonitor Newsletter Getting in Touch with us To find out more about the extensive range of Elo touch solutions visit our website at www elotouch com or simply call the office nearest you North America Tel 800 ELO TOUCH Europe Asia Pacific Latin America Elo Touch Solutions Tel 1 650
14. f the Product with minimum insurance to Buyer shall be at Seller s expense Buyer shall bear the risk of loss or damage in transit and may insure the Product Buyer shall reimburse Seller for transportation cost incurred for Product returned but not found by Seller to be defective Modification or repair of Products may at Seller s option take place either at Seller s facilities or at Buyer s premises If Seller is unable to modify repair or replace a Product to conform to the warranty set forth above then Seller shall at Seller s option either refund to Buyer or credit to Buyer s account the purchase price of the Product less depreciation calculated on a straight line basis over Seller s stated Warranty Period These remedies shall be the Buyer s exclusive remedies for breach of warranty Except for the express warranty set forth above Seller grants no other warranties express or implied by statute or otherwise regarding the products their fitness for any purpose their quality their merchantability their non infringement or otherwise No employee of Seller or any other party is authorized to make any warranty for the goods other than the warranty set forth herein Seller s liability under the warranty shall be limited to a refund of the purchase price of the product In no event shall Seller be liable for the cost of procurement or installation of substitute goods by Buyer or for any special consequential indirect or incid
15. he display with equal black bars on the left and right The touchscreen may need recalibration when switching between Aspect Ratio options Adjusts sharpness of the displayed images Sharpness Default No sharpness adjustment Only applicable at non native input video resolutions Selects the display s color temperature The available color temperatures are 9300K 7500K 6500K 5500K and User Defined If the User Defined option is selected the user can change the color temperature by changing individual R G and B gains ona scale from 0 to 100 Default User Defined with R G and B all set to 100 Adjusts how long a period of OSD button inactivity the touchmonitor will wait before OSD Timeout closing the OSD The adjustable range is between 5 and 60 seconds Default 15 seconds Color Temperature User Manual 1523L 1723L SW601951 Rev A Page 18 of 29 Selects which language the OSD information is displayed in The available languages OSD are English French Italian German Spanish Simplified Chinese Traditional Language Chinese and Japanese Default English Volume Adjusts the volume of the internal speakers and headphone output Mute Toggles the audio output between Muted and Not Muted Default Not Muted Recall Selecting Recall Defaults restores all factory default settings for OSD adjustable Defaults parameters except OSD Language and for Preset Video Mode timings Video
16. om go websupport for online self help Visit www elotouch com go contactsupport for technical support See this user manual s last page for worldwide technical support phone numbers User Manual 1523L 1723L SW601951 Rev A Page 21 of 29 Chapter 6 Safety amp Maintenance Safety To avoid risk of electric shock follow all safety notices and do not disassemble the touchmonitor They are not user serviceable Ensure that your installation is equipped to maintain the specified environmental conditions listed in the Technical Specifications chapter Care and Handling The following tips will help keep your touchmonitor functioning at an optimal level Disconnect the AC power cable before cleaning To clean the display unit cabinet use a clean cloth lightly dampened with a mild detergent It is important that your unit remains dry Do not get liquids on or inside the unit If liquid does get inside have a qualified service technician check it before you power it on again Do not wipe the screen with a cloth or sponge that could scratch the surface To clean the touchscreen use window or glass cleaner applied to a clean cloth or sponge Never apply the cleaner directly to the touchscreen Do not use alcohol methyl ethyl or isopropyl thinner benzene or other abrasive cleaners TAII 0 UCH A User Manual 1523L 1723L SOLUTIONS SW601951 Rev A Page 22 of 29 Waste Electrical amp Electronic Equipment Directive WE
17. onitor a threaded three hole mounting pattern for M4 screws is provided on the bottom of stand base for mounting or securing 196 M4 THREAD MAX SCREW LENGTH 7mm FROM MOUNTING 36 2 SURFACE X3 CABLE HOLE 172 4 User Manual 1523L 1723L SW601951 Rev A Page 13 of 29 Chapter 4 Operation Power To turn the touchmonitor on or off press the touchmonitor power button once The Power Status LED on the bottom of the touchmonitor functions according to the following table TouchMonitor Computer Module status LED status ae eT O OOE O OFF OFF SLEEP PULSING The system consumes low power when in SLEEP and OFF modes For detailed power consumption specifications refer to technical specifications on the Elo website http www elotouch com Touching the screen will bring the attached host PC out of SLEEP mode similar to moving the mouse or pressing a keyboard key To improve reliability and reduce wasteful power consumption disconnect the power adapter when long periods of disuse are planned Touch Your touchmonitor is factory calibrated and should not need manual calibration unless the input video is not fully scaled to the native resolution or the touch experience needs to be calibrated to a specific user iTouch Plus Touch Technology When connected to Windows 7 computers the touchmonitor can report 2 simultaneous touches When connected to Windows XP computers the touchmonitor reports single t
18. ouches The iTouch Plus touchscreen can be re calibrated to your displayed video image if a User Manual 1523L 1723L SW601951 Rev A Page 14 of 29 needed through the Calibration function in the Elo driver control panel The iTouch Plus driver will only support multiple monitor if they are all using the iTouch Plus touch technology To use multiple iTouch Plus monitors double click on the EloConfig desktop shortcut to open up the Elo Touchscreen Configuration screen lelo EloConfig Select Match Touch to Display to calibrate multiple monitors Copyrights Component versions Build info Restart Elo touch device service Restart Tablet Input Service Match touch input to a display for English OS with multiple monitors Match Touch to Display Align all touchmonitors Align Elo Touchmonitors Device info Edge acceleration Disable touch Restore default calibration Touchmonitor Properties Apply to all monitors Hide cursor during calibration Increase size of Windows title bars Common Settings Elo support info Download driver packages for different platforms Online Support Projected Capacitive Touch Technology When connected to Windows 7 computers the touchmonitor can report 2 simultaneous touches When connected to Windows XP computers the touchmonitor reports single touches No additional drivers are required for thi
19. red to Buyer Seller warrants to Buyer that the Product shall be free of defects in materials and workmanship The warranty for the Touchmonitors and their components is 3 three years Seller makes no warranty regarding the model life of components Seller s suppliers may at any time and from time to time make changes in the components delivered as Products or components Buyer shall notify Seller in writing promptly and in no case later than thirty days after discovery of the failure of any Product to conform to the warranty set forth above shall describe in commercially reasonable detail in such notice the symptoms associated with such failure and shall provide to Seller the opportunity to inspect such Products as installed if possible The notice must be received by Seller during the Warranty Period for such product unless otherwise directed in writing by the Seller Within thirty days after submitting such notice Buyer shall package the allegedly defective Product in its original shipping carton s or a functional equivalent and shall ship to Seller at Buyer s expense and risk Within a reasonable time after receipt of the allegedly defective Product and verification by Seller that the Product fails to meet the warranty set forth above Seller shall correct such failure by at Seller s options either i modifying or repairing the Product or ii replacing the Product Such modification repair or replacement and the return shipment o
20. rence to radio communications Notice to Users in Canada This equipment complies with the Class B limits for radio noise emissions from digital apparatus as established by the Radio Interference Regulations of Industrial Canada Notice to Users in the European Union Use only the provided power cords and interconnecting cabling provided with the equipment Substitution of provided cords and cabling may compromise electrical safety or CE Mark Certification for emissions or immunity as required by the following standards This Information Technology Equipment ITE is required to have a CE Mark on the Manufacturer s label which means that the equipment has been tested to the following Directives and Standards This equipment has been tested to the requirements for the CE Mark a User Manual 1523L 1723L SW601951 Rev A Page 24 of 29 as required by EMC Directive 2004 108 EC as indicated in European Standard EN 55022 Class B and the Low Voltage Directive 2006 95 EC as indicated in European Standard EN 60950 General Information to all Users This equipment generates uses and can radiate radio frequency energy If not installed and used according to this manual the equipment may cause interference with radio and television communications There is however no guarantee that interference will not occur in any particular installation due to site specific factors 1 In order to meet emission and immunity requirements the user must observe
21. s technology to work it uses Windows HID drivers A A l User Manual 1523L 1723L SOLUTIONS SW601951 Rev A Page 15 of 29 No calibration is required for this technology Gesture Support The Intellitouch Plus and Projected Capacitive touch technologies enable several gestures that support single and multiple contacts Refer to the Microsoft Website http msdn microsoft com en us library dd940543 on the various gestures that are supported in Windows 7 Video A display s native resolution is its width and height measured in number of pixels Generally for best performance an image displayed on this monitor will look best when your computer s output resolution matches this monitor s native resolution which is 1024 x 768 for the 15 inch and 1280 x 1024 for the 17 inch For computer output resolutions at non native resolutions the monitor will scale the video to its panel s native resolution This involves stretching or compressing the input image as needed in the X and Y dimensions to fit the display s native resolution An unavoidable byproduct of the scaling algorithms is a loss of fidelity wnen the computer s output video image is scaled by the monitor to fit the display This loss of fidelity is most apparent when viewing feature rich images at close distances for example images containing small font text Your touchmonitor will likely not require video adjustments However for analog VGA video v
22. screw holes in the bottom of the base Upright position To convert the stand into the low profile hostess position secure the thumbscrews into the low or L screw holes in the bottom of the base Connector Panel amp Interfaces 7 AUDIO INPUT 7 DC POWER INPUT 3 5mm TRS JACK BARREL ID 6 4mm 1Vrms MAXIMUM PIN OD 2 0mm BARREL DEPTH 8 8mm INPUT VOLTAGE 12V DC 5 i 1 i 4 L USB X2 p SB TOUCH OUTPUT OLUTIONS User Manual 1523L 1723L SW601951 Rev A Page 7 of 29 Touchmonitor Connections 1 Connect the DVI or VGA video cables between the monitor s DVI VGA input connectors and your DVI VGA video source respectively Tighten the video cable s screws for best performance 2 Connect the USB touch cable between the monitor s USB connector and your PC s USB port 3 Connect the audio cable between the monitor s Audio In jack and your audio source 4 Select the correct power cable for your region Connect the power adaptor s input connector to the AC power source Connect the power adaptor s DC output connector to the monitor s input power jack 5 The touchmonitor ships in an OFF state Press the power button to turn it on Installing the Touch Technology Software Drivers Some software installation is required for your iTouch Plus touchmonitor to work with your computer No additional drivers are required for your projected capacitive tou
23. the following a Use only the provided I O cables to connect this digital device with any computer b To ensure compliance use only the provided manufacturer s approved line cord c The user is cautioned that changes or modifications to the equipment not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment 2 If this equipment appears to cause interference with radio or television reception or any other device a Verify as an emission source by turning the equipment off and on If you determine that this equipment is causing the interference try to correct the interference by using one or more of the following measures i Move the digital device away from the affected receiver ii Reposition turn the digital device with respect to the affected receiver iii Reorient the affected receiver s antenna iv Plug the digital device into a different AC outlet so the digital device and the receiver are on different branch circuits v Disconnect and remove any I O cables that the digital device does not use Unterminated I O cables are a potential source of high RF emission levels vi Plug the digital device into only a grounded outlet receptacle Do not use AC adapter plugs Removing or cutting the line cord ground may in crease RF emission levels and may also present a lethal shock hazard to the user If you need additional help consult your dealer manufact
24. urer or an experienced radio or television technician a User Manual 1523L 1723L SW601951 Rev A Page 25 of 29 lll Agency Certifications The following certifications and marks have been issued or declared for this monitor Australia C Tick Canada CUL IC China CCC Europe CE IV China RoHS Japan VCCI Korea KCC e Standby Mexico CoC Taiwan BSMI United States FCC UL In accordance to Chinese law Administration on the Control of Pollution Caused by Electronic Information Products the section below lists out the name and amount of the toxic and or hazardous materials that this product may contain Component Toxic or Hazardous Substances and Elements Name Lead Pb Mercury Hg Cadmium Cd Hexavalent Polybrominated Polybrominated Chromium _ Biphenyls Diphenyl Cr6 PBB Ethers PBDE Plastic Parts O O O O O O Metal Parts X O O O O O Wire and X O O O O O Cable Assembly LCD Panel X O O O O O Touch X O O O O O Screen Panel PCBA X O O O O O Software O O O O O O CD etc O Indicates that this toxic or hazardous substance contained in all of the homogeneous materials for this component is below the limit requirement in SJ T 11363 2006 X Indicates that this toxic or hazardous substance contained in at least one of the homogeneous materials used for this component is above the limit requirement in SJ T 11363 2006 For items marked
25. ve touch technologies are not supported by all gt operating systems including Mac and some versions of Linux See the Technology notes for each driver on Lid vanish the Driver and File Downloads page to verify support for your touchscreen technology Touch Drivers gt Windows 7 XP Vista gt Windows XP For 1541L Product only gt Windows 7 XP Vista WEPOS Server 2003 For IDS products with APR gt Windows 7 Multitouch requires IntelliTouch Plus touchmonitors and digitizer gt Embedded Operating Systems gt Mac gt Linux Windows is a trademark of Microsoft Corporation Peripheral Drivers and Utilities For Windows XP installations install the USB Touchscreen Drivers when prompted Elo Touchscreen Setup 5 2 0 43 Welcome to Elo Touchscreen Setup TOUCHSYSTEMS Install Serial Touchscreen Drivers Install APR Touchscreen Driver lt Back Next gt Cancel TOUCH User Manual 1523L 1723L SOLUTIONS SW601951 Rev A Page 9 of 29 For Windows 7 installations check the Install driver box under Elo USB Interfaces Other Touchscreens Install drivers for all detected Elo Touchscreens Alp SOLI Elo USB Interfaces APR Touchscreens 0 detected Other Touchscreens 0 detected Install driver V Install driver C Install driver on selected port s Align touchscreens at end of installation Re detect Touchscreens Close
Download Pdf Manuals
Related Search