Bosch PSU-124-DC050 power supply unit
Contents
1. II Power Supply PSU 124 DC050 6 BOSCH en Installation manual Power Supply Table of Contents en 3 Table of Contents 1 Safety 4 1 1 Safety precautions 4 1 2 Important safety instructions 5 1 3 Important Notices 8 1 4 FCC amp ICES compliance 9 1 5 UL certification 11 1 6 Bosch notices 12 2 Installation 13 2 1 Tools reguired 13 2 2 Opening the side covers 13 2 3 Mount the unit 13 2 4 Connecting the input cable 14 2 5 Connecting the output cables 15 3 Technical Data 16 3 1 Specifications 16 3 1 1 Dimensions 17 Bosch Security Systems Installation manual AR18 10 B002 v1 1 2011 10 4 en Safety Power Supply 1 Safety 1 1 Safety precautions DANGER High risk This symbol indicates an imminently hazardous situation such as Dangerous Voltage inside the product If not avoided this will result in an electrical shock serious bodily injury or death WARNING Medium risk Indicates a potentially hazardous situation If not avoided this could result in minor or moderate bodily injury CAUTION Low risk Indicates a potentially hazardous situation If not avoided this could result in property damage or risk of damage to the unit AR18 10 B002 v1 1 2011 10 Installation manual Bosch Security Systems Power Supply Safety en 5 1 2 Important safety instructions Read follow and re2. 10 B002 v1 1 2011 10 Installation manual Bosch Security Systems Power Supply Installation en 15 2 5 Connecting the output cables T lt Figure 2 4 Connecting the output cables Connect the two output cables as follows Cut back the insulation of the cable wires to approximately 5 mm 0 2 in Pass the output cables through the supplied grommets For each wire push back the tab behind the terminal with a small screwdriver and insert the wire respect the polarity shown in the figure release the tab to clamp the wire in place Secure the grommets firmly Return the protective cover to its position and fasten in place with the four cross head screws Note Tighten screws firmly to ensure protection against water ingress Bosch Security Systems Installation manual AR18 10 B002 v1 1 2011 10 16 en Technical Data Power Supply 3 Technical Data 3 1 Specifications Model PSU 124 DC050 Output DC voltage 24 VDC Rated current 2 0 A Rated power 50 W Input Voltage range 100 to 240 VAC Freguency range 50 to 60 Hz AC current 0 9 A 115 VAC 0 2 A 230 VAC Construction Weight 850 g Material Casing Aluminum extrusion End caps mild steel Finish Powder coated paint RAL 9010 Pure White Cable glands Suitable for cable diameter 4 to 8 mm Environment Water protection IP66 Worki
3. d terminer la production d interf rences en mettant l appareil successivement hors et sous tension tout en contr lant la r ception radio ou t l vision L utilisateur peut parvenir liminer les interf rences ventuelles en prenant une ou plusieurs des mesures suivantes Modifier l orientation ou l emplacement de l antenne r ceptrice Eloigner l appareil du r cepteur Brancher l appareil sur une prise situ e sur un circuit diff rent de celui du r cepteur Consulter le revendeur ou un technicien qualifi en radio t l vision pour obtenir de l aide Toute modification apport e au produit non express ment approuv e par la partie responsable de l appareil est strictement interdite Une telle modification est susceptible d entra ner la r vocation du droit d utilisation de l appareil La brochure suivante publi e par la Commission f d rale des communications FCC peut s av rer utile How to Identify and Resolve Radio TV Interference Problems Comment identifier et r soudre les probl mes d interferences de radio et de t l vision Cette brochure est disponible aupr s du U S Government AR18 10 B002 v1 1 2011 10 Installation manual Bosch Security Systems Power Supply Safety en 11 1 5 Printing Office Washington DC 20402 Etats Unis sous la r f rence n 004 000 00345 4 UL certification Disclaimer Underwriter Laboratories Inc UL has not tested the performance or
4. reliability of the security or signaling aspects of this product UL has only tested fire shock and or casualty hazards as outlined in UL s Standard s for Safety for Closed Circuit Television Eguipment UL 2044 UL Certification does not cover the performance or reliability of the security or signaling aspects of this product UL MAKES NO REPRESENTATIONS WARRANTIES OR CERTIFICATIONS WHATSOEVER REGARDING THE PERFORMANCE OR RELIABILITY OF ANY SECURITY OR SIGNALING RELATED FUNCTIONS OF THIS PRODUCT Disclaimer Underwriter Laboratories Inc UL has not tested the performance or reliability of the security or signaling aspects of this product UL has only tested fire shock and or casualty hazards as outlined in UL s Standard s for Safety for Information Technology Eguipment UL 60950 1 UL Certification does not cover the performance or reliability of the security or signaling aspects of this product UL MAKES NO REPRESENTATIONS WARRANTIES OR CERTIFICATIONS WHATSOEVER REGARDING THE PERFORMANCE OR RELIABILITY OF ANY SECURITY OR SIGNALING RELATED FUNCTIONS OF THIS PRODUCT Bosch Security Systems Installation manual AR18 10 B002 v1 1 2011 10 12 en Safety Power Supply 1 6 Bosch notices Disposal Your Bosch product was developed and manufactured with high guality material and components that can be recycled and reused This symbol means that electronic and electrical appliances which have reached the end of their
5. the eguipment so it is easily accessible AR18 10 B002 v1 1 2011 10 Installation manual Bosch Security Systems Power Supply Safety en 9 1 4 FCC amp ICES compliance FCC amp ICES Information U S A and Canadian Models Only This eguipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This eguipment generates uses and can radiate radio freguency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this eguipment does cause harmful interference to radio or television reception which can be determined by turning the eguipment off and on the user is encouraged to try to correct the interference by one or more of the following measures reorient or relocate the receiving antenna increase the separation between the equipment and receiver connect the equipment into an outlet on a circuit different from that to which the receiver is connected consult the dealer or an experienced radio TV technician for help Intentional or unintentional modifications not expressly approved by the party responsible for compliance shall not be made Any s
6. working life must be collected and disposed of separately from household waste material Separate collecting systems are usually in place for disused electronic and electrical products Please dispose of these units at an environmentally compatible recycling facility per European Directive 2002 96 EC Copyright This manual is the intellectual property of Bosch Security Systems and is protected by copyright All rights reserved Trademarks All hardware and software product names used in this document are likely to be registered trademarks and must be treated accordingly NOTE This manual has been compiled with great care and the information it contains has been thoroughly verified The text was complete and correct at the time of printing The ongoing development of the products may mean that the content of the user guide can change without notice Bosch Security Systems accepts no liability for damage resulting directly or indirectly from faults incompleteness or discrepancies between the user guide and the product described More information For more information please contact the nearest Bosch Security Systems location or visit www boschsecurity com AR18 10 B002 v1 1 2011 10 Installation manual Bosch Security Systems Power Supply Installation en 13 2 Installation CAUTION Installation should only be performed by qualified service personnel in accordance with the National Electrical C
7. ightning and power line surges Controls adjustment Adjust only those controls specified in the operating instructions Improper adjustment of other controls may cause damage to the unit Use of controls or adjustments or performance of procedures other than those specified may result in hazardous radiation exposure Bosch Security Systems Installation manual AR18 10 B002 v1 1 2011 10 6 en Safety Power Supply 7 10 11 Overloading Do not overload outlets and extension cords This can cause fire or electrical shock Power cord and plug protection Protect the plug and power cord from foot traffic being pinched by items placed upon or against them at electrical outlets and its exit from the unit For units intended to operate with 230 VAC 50 Hz the input and output power cord must comply with the latest versions of EC Publication 227 or IEC Publication 245 Power disconnect Units have power supplied to the unit whenever the power cord is inserted into the power source The power cord plug is the main power disconnect device for switching off the voltage for all units Power sources Operate the unit only from the type of power source indicated on the label Before proceeding be sure to disconnect the power from the cable to be installed into the unit For battery powered units refer to the operating instructions For external power supplied units use only the recommended
8. ng temperature 30 to 50 C 22 to 122 F Working humidity 20 to 95 RH non condensing Storage temperature 40 to 80 C 40 to 176 F Storage humidity 10 to 95 RH non condensing AR18 10 B002 v1 1 2011 10 Installation manual Bosch Security Systems Power Supply Technical Data en 17 Safety amp EMC Safety standards EN60950 1UL60950 1EN60950 22 IP66 Harmonic current Compliance to Class C less than 75 load EN61000 3 3 EMS immunity Compliance to EN61000 4 2 3 4 5 6 8 11 ENV50204 EN55024 EN61547 light industry level surge 4KV criteria A 3 1 1 Dimensions 123 4 84 E 101 3 98 81 3 17 H d 91 3 57 150 5 9 195 7 68 47 1 85 Figure 3 1 Dimensions Bosch Security Systems Installation manual AR18 10 B002 v1 1 2011 10 18 en Technical Data Power Supply AR18 10 B002 v1 1 2011 10 Installation manual Bosch Security Systems Bosch Security Systems Inc 850 Greenfield Road Lancaster PA 17601 USA www boschsecurity com Bosch Security Systems Inc 2011
9. ode or applicable local codes Disconnect the supply power before installing 2 1 2 2 2 3 Tools reguired Small flat blade screwdriver Crosshead screwdriver Wire cutter stripper tool Opening the side covers H K x K O Figure 2 1 Removing side covers Unscrew the four cross head screws at each corner and remove each of the side covers Mount the unit N K Figure 2 2 Mounting the unit Secure the unit to a flat surface using mounting screws not supplied in the four holes 4 mm shown in the figure Bosch Security Systems Installation manual AR18 10 B002 v1 1 2011 10 14 enl installation Power Supply 2 4 Connecting the input cable a 5 mm 0 2 in Input 110 230 VAC 50 60 Hz Neutral In Live In Earth In Figure 2 3 Connecting the input cable Connect input supply cable as follows Cut back the insulation of the cable wires to approximately 5 mm 0 2 in Pass the input cable through the supplied grommet For each wire push back the tab behind the terminal with a small screwdriver and insert the wire respect the polarity shown in the figure release the tab to clamp the wire in place Secure the grommet firmly Return the protective cover to its position and fasten in place with the four cross head screws Note Tighten screws firmly to ensure protection against water ingress AR18
10. or approved power supplies For limited power source units this power source must comply with EN60950 Substitutions may damage the unit or cause fire or shock For24 VAC units voltage applied to the unit s power input should not exceed 10 or 28 VAC User supplied wiring must comply with local electrical codes Class 2 power levels Do not ground the supply at the terminals or at the unit s power supply terminals If unsure of the type of power supply to use contact your dealer or local power company Servicing Do not attempt to service this unit yourself Opening or removing covers may expose you to dangerous voltage or other hazards Refer all servicing to gualified service personnel AR18 10 B002 v1 1 2011 10 Installation manual Bosch Security Systems Power Supply Safety en 7 12 13 14 15 16 Damage reguiring service Unplug the unit from the main AC power source and refer servicing to gualified service personnel when any damage to the eguipment has occurred such as the power supply cord or plug is damaged exposure to moisture water and or inclement weather rain snow etc liquid has been spilled in or on the equipment an object has fallen into the unit unit has been dropped or the unit cabinet is damaged unit exhibits a distinct change in performance unit does not operate normally when the user correctly follows the o
11. or protection of the device the branch circuit protection must be secured with a maximum fuse rating of 16A This must be in accordance with NEC800 CEC Section 60 Grounding and polarization This unit may be equipped with a polarized alternating current line plug a plug with one blade wider than the other blade This safety feature allows the plug to fit into the power outlet in only one way If unable to insert the plug fully into the outlet contact a locally certified electrician to replace the obsolete outlet Do not defeat the safety purpose of the polarized plug Alternately this unit may be equipped with a 3 pole grounding plug a plug with a third pin for earth grounding This safety feature allows the plug to fit into a grounded power outlet only If unable to insert the plug into the outlet contact a locally certified electrician to replace the obsolete outlet Do not defeat the safety purpose of the grounding plug Moving Disconnect the power before moving the unit Move the unit with care Excessive force or shock may damage the unit Outdoor signals The installation for outdoor signals especially regarding clearance from power and lightning conductors and transient protection must be in accordance with NEC725 and NEC800 CEC Rule 16 224 and CEC Section 60 Permanently connected eguipment Incorporate a readily accessible disconnect device external to the eguipment Pluggable eguipment Install the socket outlet near
12. perating instructions Replacement parts Be sure the service technician uses replacement parts specified by the manufacturer or that have the same characteristics as the original parts Unauthorized substitutions may cause fire electrical shock or other hazards Safety check Safety checks should be performed upon completion of service or repairs to the unit to ensure proper operating condition Installation Install in accordance with the manufacturer s instructions and in accordance with applicable local codes Attachments changes or modifications Only use attachments accessories specified by the manufacturer Any change or modification of the eguipment not expressly approved by Bosch could void the warranty or in the case of an authorization agreement authority to operate the eguipment Bosch Security Systems Installation manual AR18 10 B002 v1 1 2011 10 8 en Safety Power Supply 1 3 Important Notices All pole power switch Incorporate an all pole power switch with a contact separation of at least 3 mm in each pole into the electrical installation If it is needed to open the housing for servicing and or other activities use this all pole switch as the main disconnect device for switching off the voltage to the unit Environmental statement Bosch has a strong commitment towards the environment This unit has been designed to respect the environment as much as possible Fuse rating F
13. tain for future reference all of the following safety instructions Heed all warnings on the unit and in the operating instructions before operating the unit 1 Cleaning Unplug the unit from the outlet before cleaning Follow any instructions provided with the unit Generally using a dry cloth for cleaning is sufficient but a moist fluff free cloth or leather shammy may also be used Do not use liquid cleaners or aerosol cleaners Heat Sources Do not install the unit near any heat sources such as radiators heaters stoves or other eguipment including amplifiers that produce heat Ventilation Any openings in the unit enclosure are provided for ventilation to prevent overheating and ensure reliable operation Do not block or cover these openings Do not place the unit in an enclosure unless proper ventilation is provided or the manufacturer s instructions have been adhered to Object and liguid entry Never push objects of any kind into this unit through openings as they may touch dangerous voltage points or short out parts that could result in a fire or electrical shock Never spill liguid of any kind on the unit Do not place objects filled with liguids such as vases or cups on the unit Lightning For added protection during a lightning storm or when leaving this unit unattended and unused for long periods unplug the unit from the wall outlet and disconnect the cable system This will prevent damage to the unit from l
14. uch modifications could void the user s authority to operate the eguipment If necessary the user should consult the dealer or an experienced radio television technician for corrective action The user may find the following booklet prepared by the Federal Communications Commission helpful How to Identify and Resolve Radio TV Interference Problems This booklet is available from the U S Government Printing Office Washington DC 20402 Stock No 004 000 00345 4 Bosch Security Systems Installation manual AR18 10 B002 v1 1 2011 10 10 en Safety Power Supply Informations FCC et ICES modeles utilis s aux Etats Unis et au Canada uniquement Suite a diff rents tests cet appareil s est r v l conforme aux exigences impos es aux appareils num riques de classe B en vertu de la section 15 du r glement de la Commission f d rale des communications des Etats Unis FCC et en vertu de la norme CES 003 d Industrie Canada Ces exigences visent fournir une protection raisonnable contre les interf rences nuisibles lorsque l appareil est utilis dans le cadre d une installation r sidentielle Cet appareil g n re utilise et met de l nergie de radiofr quences et peut en cas d installation ou d utilisation non conforme aux instructions engendrer des interf rences nuisibles au niveau des radiocommunications Toutefois rien ne garantit l absence d interf rences dans une installation particuli re Il est possible de
Download Pdf Manuals
Related Search