Denver MT-979DVBT
Contents
1. SET After connection is firmed and securely done plug AC ADAPTER to an applicable wall outlet and turn on the player CHARGE THE BUILT IN BATTERY The player is with a rechargeable lithium battery Before using the battery please make sure it is charged If not charge it first Slide the power switch to OFF position and then connect one end of the supplied adapter to the wall outlet and the other end to the unit for charging the built in battery Note 1 The battery only could be charged at powering off mode 2 If the unit is not in use for a prolonged period of time it is recommendable to charge the built in battery each three months CONNECTING TO A CAR ADAPTOR The car power adaptor is designed for use with vehicles that have a 12V negative ground electrical system WARNING Disconnect the car power adaptor when not in use Not in use in 24V vehicles L To the cigarette lighter socket CAUTIONS e Use the unit only with the recommended car power adaptor use with other car power adaptor might damage the unit e The recommended car power adaptor is for use with this unit only Do not use it with other equipment e Inthe interests of road traffic safety do not operate the unit or view video software while driving a vehicle e Make sure the unit is fastened securely to prevent from moving outside of the vehicle in an accident e When the inside of the cigarette lighter socket is dirty with ashes or dust2. is disabled 1 3 TV TYPE it is used to select the TV scan mode please set as per your TV set Options 4 3PS Normal Pan amp scan mode 4 3LB normal Letter box mode 16 9 16 9 wide screen mode 1 4 PASSWORD input password to unlock the system The steps are as follows 1 4 1 Enter SYSTEM SETUP select the PASSWORD item by scrolling the down navigation button and then press the right navigation button to select the input box 1 4 2 Input user s password 0000 to unlock it in this case select the input box again to change the password by inputting another new four numeric numbers and then press OK button to confirm When the password is changed you are needed to input the new one to unlock the system 1 4 3 Once you forget your own password use the supervisor s password 8200 to unlock it NOTE If wrong password was input in unlock status the system will lock 1 5 RATING Set the rating of this player If you want to change the rating of parental lock please input the password to unlock first Options 1 KID SAFE 2G 3PG 4PG 13 5 PG R 6R 7 NC 17 8 ADULT 1 6 DEFAULT Reset to factory settings Options RESTORE 2 LANGUAGE SETUP LANGUAGE SETUP OSD LANGUAGE AUDIO LANG SUBTITLE LANG MENU LANG 2 1 OSD LANGUAGE It is used to select different On Screen Display language for different user 2 2 AUDIO LANG select preferred audio language DVD only need disc software support 2 3 SUBTITLE
3. sure that the batteries are recycled in accordance with legislature and will not harm the environment All cities have established collection points where electric and electronic equipment and batteries can either be submitted free of charge at recycling stations and other collection sites or be collected from the households Additional information is available at the technical department of your city
4. the plug section may become hot due to poor contact Be sure to clean the cigarette lighter socket before use e After use disconnect the car power adaptor from both the unit and cigarette lighter socket FUSE REPLACEMENT POSITIVE CAP NOTE Don t throw out the positive cap when replace the fuse CONNECTING THE AERIAL TO THE PLAYER Aerial input 1 When this player is connect to the outdoor aerial make sure that the TV programme is available from the signal tower 2 The quality of video is depend on the signal strength 3 When this player is connect to the outdoor aerial in avoid that the huge buildings or obstacle would block the signal OPERATIONS PREPARATION Power on the TV set and select video input mode Power on the audio system which is connected to the player GET STARTED 1 Slide POWER switch to turn on the player 2 Press disc cover Open button to open the disc tray 3 Place a disc onto the disc tray 4 Close the disc tray by hand and the playback starts automatically 5 When a menu screen appears on the TV move the navigation buttons or press the numeric buttons to select a preferred track number then press OK button to start playback NOTE If at DVB T mode pressing FUNCTION button on the remote or long pressing FUNCTION button on the unit for switching to DVD mode is necessary ADJUST THE VOLUME Press VOLUME button repeatedly to increase or reduce the volume M
5. to play 2 Press NEXT or PREVIOUS button to skip forward or backward Note Press and hold STOP button on the remote or press DVD USB SD button on the unit to make selection among USB card and disc via navigation LEFT RIGHT button confirm by pressing OK button lt gt CENTER CAUTION To avoid electronic static discharge don t touch the USB port and card slot during playback INITIAL SETTINGS Initial settings page is for you to make your preferred settings up for your player Once the initial settings are done they are retained in the CPU of the player until otherwise modified COMMON PROCEDURES FOR INITIAL SETTINGS 1 Press SETUP button to access the setup menu 2 Use the navigation buttons to select the item you want to modify setting page with further setting items displayed shows on the TV screen Again use navigation buttons to make changes Press OK button to confirm modifications 3 Use navigation buttons to switch to another setting on the main setting page 4 Press SETUP button to exit main setting page 1 SYSTEM SETUP SYSTEM SETUP TV SYSTEM SCREEN SAVER TV TYPE PASSWORD RATING DEFAULT 1 1 TV SYSTEM it is used to select the TV mode Please select this option as per your TV set 1 2 SCREEN SAVER when the player is not in use for several minutes a running DVD logo will move across the TV screen to protect the TV screen Options On Screen saver is enabled Off Screen saver
6. DENVER Operating Manual PORTABLE LCD DVD PLAYER Model MT 979DVBT 0O o O Od jo OD 00 READ THESE INSTRUCTIONS INCLUDED IN THIS IM THOROUGHLY PRIOR TO CONNECTING AND OPERATING PLEASE RETAIN THIS MANUAL IN CASE YOU MAY NEED IT FOR FUTURE REFERENCE THE ILLUSTRATIONS amp GRAPHICS HEREIN ARE FOR REFERENCE ONLY AND SUBJECT TO CHANGE WITHOUT NOTICE ALL RIGHTS RESERVED COPYRIGHT DENVER ELECTRONICS A S www denver electronics com OVERVIEW OF THE DVD PLAYER ANT JACK DISC COVER OPEN KEY DISC TAKEN AREA DISC COVER NAVIGATION LEFT KEY CH NAVIGATION DOWN KEY TFT SCREEN SPEAKERS PREVIOUS amp F BWD KEY 10 NEXT amp F FWD KEY 11 FUNCTION PLAY PAUSE KEY 12 STOP KEY 13 VOLUME KEY 14 VOLUME KEY 15 SETUP KEY 16 DVD USB SD KEY 17 CH NAVIGATION UP KEY 18 NAVIGATION RIGHT KEY 19 OK KEY 20 DC IN JACK 21 SD MMC CARD SLOT 22 POWER ON OFF SWITCH 23 AV OUT JACK 24 PHONE JACK 25 USB PORT 26 CHARGE INDICATOR REMOTE SENSOR POWER INDICATOR ONOahWHND MUTE button LANGUAGE button SCREEN ON OFF button STOP amp USB CARD button VOLUME button DVD MENU button NAVIGATION UP amp CH button NAVIGATION LEFT button OK PLAY PAUSE button TV RADIO button 11 NUMERIC buttons 19 12 PROGRAM ANGLE EPG button 13 FUNCTION 4 4 VOL DISPLAY I
7. LANG Select preferred subtitle language DVD only need disc software support 2 4 MENU LANG Select preferred disc menu language DVD only need disc software support 3 VIDEO SETUP VIDEO SETUP BRIGHTNESS CONTRAST HUE SATURATION 3 1 BRIGHTNESS to set the brightness for the display Options 0 2 4 6 8 10 12 3 2 CONTRAST to set the contrast effect for display Options 0 2 4 6 8 10 12 3 3 HUE to set the colour impression for display Options 6 4 2 0 2 4 6 3 4 SATURATION to set the saturation level for display Options 0 2 4 6 8 10 12 5 4 SPEAKER SETUP SPEAKER SETUP DOWNMIX 4 1 DOWNMIX Options LT RT Left Right mix mode STEREO Select this option if you don t have a 5 1 channels amplifier DVB OPERATIONS GET STARTED e Be sure the TV antenna is connected to your player properly e Power on the player and press FUNCTION button on the remote or press and hold FUNCTION button on the unit to switch to DVB T mode A dialogue of first time installation shows on the screen select YES option to perform the first time installation then select the options as mentioned in the dialogue to finish the first time installation select NO option to exit this interface SEARCH A PROGRAM Press NAVIGATION UP DOWN button to change the channel number A desired channel can be reached using these two keys Once the desired channel is selected it will start broadcasting the se
8. NFO 16 an m q 3 COONOoaRWND O ON OUR UN a m 1 fi 20 PREVIOUS amp F_BWD button SUBTITLE 21 14 FUNCTION button 22 15 SETUP button Aili 16 DISPLAY INFO button 11 4 C4 C8 C6 CH az 17 VOLUME button sea 18 TITLE button ee pee a 19 NAVIGATION RIGHT button 12 25 20 TTX button ae ax Sa Se a 21 NAVIGATION DOWN amp CH button 22 SUBTITLE button PPI 13 COE 23 AUDIO button DE NVE R 24 SEARCH button 25 REPEAT FAV button 26 ZOOM SLOW button 27 NEXT amp F_FWD button CONNECT DVD PLAYER TO OTHER APPLIANCES e t is recommended you connect the player to a multi system TV e Ensure that this player and other appliances TV set and amplifier that will be connected to the player are set to OFF mode and that the AC cords are disconnected from the wall outlet e Avoid blocking ventilation holes of the connected appliances and make sure air around there can circulate freely e Read carefully and follow the instructions before connecting other appliances e Ensure that you observe the color coding when connecting audio video cables If the RCA adapter is supplied only the audio video RCA cable is required Plug one end of the RCA adapter to the unit Then connect the audio video RCA cable to the RCA adapter and the television Note The AV cable with 3 5mm diameter and 1 5cm length plug is not applied to the product TV
9. P to enter preview mode 2 SKIP TO NEXT PREVIOUS PICTURE Press NEXT button to skip to the next picture or PREV button to the previous picture 3 PICTURE ROTATIONS Press RIGHT and LEFT navigation buttons to rotate the picture Clockwise and anti clockwise respectively 4 PICTURE FLIP AND TURN Press UP navigation button to flip the picture up or down Press DOWN navigation button to flip the picture left or right 5 PICTURE ZOOM IN OUT Press ZOOM button continuously the picture zooms in by 2 3 4 times or zooms out by 1 2 1 3 1 4 of the original size Press this button once more when the picture getting 1 4 size to return to the normal play If the picture is enlarged you may use the navigation buttons to view blocked parts of the picture 6 SLIDE SHOW TRANSITION MODES During slide show playback press the PROGRAM button cyclically to select one transition mode to play picture EXTERNAL MEMORY MEDIA OPERATION USB amp SD MMC CARD Prepare the player for External Memory media operation 1 Slide the POWER switch to ON position Insert a USB data traveller filled with media files into the USB port or plug a SD MMC card into the card slot the USB or the SD MMC card is successfully detected select a corresponding function via navigation right left button for play and press OK Button to confirm Ib ENTER Folders show on the screen and use navigation buttons to select your desired folder and track
10. UTE While the power is on the audio output of the main unit is to be switch off by pressing the button Press it again to resume sound output SKIP AHEAD OR BACK Press PREVIOUS button during play to skip previous chapter DVD or a track CD Press NEXT button during play to skip next chapter DVD or a track CD RAPID ADVANCE REVERSE During playback press and hold F FWD button or F BWD button to scan the disc forward or backward at X2 X4 X8 X20 of normal speed Press PLAY PAUSE button to resume normal play STOP PLAYBACK Press STOP button during playback to stop playback the player activates its resume function when STOP is pressed in STOP mode press PLAY PAUSE button again playback resumes at the point it stopped previously open the disc tray or press the STOP button one more time to clear the resume function SLOW MOTION PLAY DVD Press and hold SLOW button during playback the disc will be played at 1 2 of normal speed at first each time this button is pressed the play speed becomes slower down to 1 7 of normal speed Press PLAY PAUSE button normal play will resume REPEAT Press REPEAT button during play it will repeat play one chapter title or repeat all for DVD disc or repeat play a track or all tracks for CD or repeat the sections between two specific points A B SEARCH FOR PREFERRED SCENE 1 Press SEARCH button during play and highlight the item to be played Title Chapter or Chapter tim
11. anning the channels Manual scan scroll to manual scan option a dialogue shows on the screen for you to set after then select lt start scan gt option to begin scanning the channels Default setup select this option to restore the factory setting DISC HANDLING PRECAUTIONS e Hold the disc by the edge so the surface will not be soiled with finger prints Finger prints dirt and scratches can cause skipping and distortion Do not write on the label side with a ball point pen or other writing utensils Do not apply benzine thinner and liquid that prevents against static electricity Be careful not to drop or bend the disc Install only one disc on the disc tray Do not try to close the disc tray when the disc is not installed properly Be sure to store the disc in its case when not in use TROUBLESHOOTING If your DVD player does not seem to be functioning properly check the items below before you contact an authorized service center Symptom Check Power does not turn on or e Make sure the adapter is securely plugged in suddenly turns off e Turn the power off and then back on Battery pack is in place but Check that the battery pack is charged If not recharge it the power does not turn on or suddenly turns off Remote control won t work Check that the battery is inserted in the and direction properly e The battery may be flat Replace it with a new one e Check that the signal transmissi
12. e by navigation buttons 2 Input the desired number or time via the numeric buttons 3 Press OK button to confirm and the playback from the located scene starts 4 To exit search menu press SEARCH button directly PROGRAM PLAY UP TO 16 MEMORIES 1 Press PROGRAM during playback to display the program menu PROG TeC T C T C T C 1 EA 5 9 i 13 i 2 a 10 nse 14 on osere al e ue aa 8 i 12 416 PLAY CLEAR 2 Select location s to be memorized via navigation buttons and then enter desired Titles Chapters numbers via numeric buttons Example Track 3 press 3 Track 12 press 1 and then 2 Track 21 press 2 and then 1 3 To start programmed playback select PLAY on the menu pressing PROGRAM button again to exit programming 4 To change programmed items scroll the navigation button to the item to be changed and enter the desired track number on the screen the selected Item will be changed To clear all items select the lt CLEAR gt on the menu and then press OK button on remote control 5 You can also cancel program mode by clearing all the items in the program menu ZOOM PLAY Press ZOOM button continuously to zoom in the picture by 2 3 and 4 times zoom out by 1 2 1 3 1 4 of normal size Press this button once more when the picture is at 1 4 size to return to the normal size display Scroll to view the enlarged picture using Navigati
13. hannels It is used to enter the Radio channels list for you to select or sort the Radio channels as your desired Channels class Select this option to edit the programs as your desired Channels edit Select this option to edit the channels name move or delete the channels as your desired so LA 2 System config TV setting TV system it is used to select TV system TV type it is used to select the TV scan mode please set as per your TV set Options 4 3PS Normal Pan amp scan mode 4 3LB Normal Letter box mode 16 9 16 9 wide screen mode Video setting BRIGHTNESS to set the brightness for the display CONTRAST to set the contrast effect for display HUE to set the colour impression for display SATURATION to set the saturation level for display Language Please select one of desired language for the system Parent Control Change pin lt is used to change the password 1 Enter old password in the OLD PIN row 2 Enter new password in the NEW PIN row 3 Enter the new password again in the CONFIRM row The default user password is 0000 Channel lock it is used to lock the channels Time setting Time zone it is used to select local time zone System info Select this option the system info shows on the screen such as Update date Tuner info F W version Model version etc 3 Installation Auto Scan select one of country from lt select area gt row then enter lt start scan gt row by navigation button to begin sc
14. lected channel immediately SWITCHING BETWEEN TV RADIO During DVB play mode press TV RADIO button on the remote to switch to RADIO play mode Need signal source support TELETEXT Press TTX button to display teletext information Need signal source support ELECTRONIC PROGRAM GUIDE Press EPG button on the remote to enter into electronic program guide in DVB mode Need signal source support PROGRAM INFORMATION Press INFO button during DVB play mode to show the program detail information Need signal source support LANGUAGE Press LANGUAGE button on the remote to change different language supplied by TV programs in DVB mode Need signal source support FAVORITE Press FAV button to enable or disable the favorite function after set the channels class on the setup menu and press navigation UP DOWN menu to switch the channel among your favorite channels selected on the setup menu DVB T SETUP MENU 1 Press SETUP Button once the setup menu will be called out on the screen 2 Use navigation LEFT RIGHT button to switch among the three different main setup interfaces Press navigation UP DOWN button to highlight the setting options and enter corresponding submenu as indication After setting press SETUP button to go back main setup interface 3 Use SETUP button to exit setup menu 1 Channel Guide TV channels It is used to enter the TV channels list for you to select or sort the TV channels as your desired Radio c
15. ly e No naked flame sources such as lighted candles should be placed on the apparatus e Minimum distances 2 0cm around the apparatus for sufficient ventilation The ventilation should not be impeded by covering the ventilation openings with items such as newspapers table cloths curtains etc e The use of apparatus is in tropical and or moderate climates e Attention should be drawn to the environmental aspects of battery disposal e CAUTION Danger of explosion if battery is incorrectly replaced Replace only with the same or equivalent type e Battery shall not be exposed to excessive heat such as sunshine fire or the like e Excessive sound pressure from earphones and headphones can cause hearing loss e The marking plate is located at the bottom of the apparatus Electric and electronic equipment and included batteries contains materials components and substances that can be hazardous to your health and the environment if the waste material discarded electric and electronic equipment and batteries is not handled correctly Electric and electronic equipment and batteries is marked with the crossed out trash can symbol seen below This symbol signifies that electric and electronic equipment and batteries should not be disposed of with other Es household waste but should be disposed of separately As the end user it is important that you submit your used batteries to the appropriate and designated facility In this manner you make
16. on buttons ON SCREEN DISPLAY INFORMATION When the player is in operation press DISPLAY button continuously the screen will display parts of information current disc type title number chapter number playtime audio language audio type subtitle language and multi angle etc in a sequence CHANGING AUDIO SOUNDTRACK LANGUAGE DVD DISC It is possible to change the audio soundtrack language to a different language from the one selected at the initial settings This operation works only with discs on which multiple audio soundtrack languages are recorded Press AUDIO button during DVD disc play the sound track will be changed with a selected sound track showing on the screen NOTE When no soundtrack languages are recorded pressing this button will not work MULTI ANGLE VIEWING DVD ONLY Press and hold ANGLE button to select your desired angle to view the scene Note only the DVDs shot with multi angle scenes have this function CHANGING SUBTITLE LANGUAGE DVD ONLY Press SUBTITLE button several times during DVD playback the subtitle language will be changed with the a selected subtitle language showing on the screen When the desired language appears release the button to view the subtitle in that language Note this function only works on the DVDs recorded with multi language subtitles RETURN TO MAIN MENU AND PLAY THE TITLE DVD During playback press DVD MENU button to return to main menu and press TITLE but
17. on is directed at the remote control sensor on the DVD player e Remove the obstacle between the remote controller and remote control sensor No picture or sound e Check that the A V cables are securely connected e Check that the disc is a DVD DVD RW or AUDIO CD e Do not use a disc that has scratches or dirt e Check that the label side of the disc is facing up The pick up lens of the DVD player may be dirty Contact the service center for lens cleaning e Check that the TV channel is set to VIDEO or AV if viewing with a TV No picture e Check that the LCD display is turned on No sound e Check that the display panel is open If it is closed audio will not be output to the speakers e Check the volume setting If set to zero turn up volume level e Check that the headphones are plugged into the PHONES socket Speakers cannot be used with the headphones No picture and sound e Check that the battery is properly installed and the Adapter is properly connected Distorted video or sound e Use a disc without scratches or dents IMPORTANT SAFETY INSTRUCTIONS e The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids such as vases shall be placed on the apparatus e When the AC DC adapter is used as the disconnect device the disconnect device shall remain readily operable To be completely disconnected the power input the AC DC adapter shall be disconnected from the mains complete
18. ton to play the title MP3 MPEG 4 PLAYBACK 1 Load the MP3 MPEG 4 disc onto the disc tray then select a corresponding function to play the disc with navigation left right button and press OK Button to confirm Then the TV screen will show folders of corresponding format on the disc lt gt 2 Select the folder you want by the navigation buttons and then press OK button to confirm 3 The files in this folder are displayed and select your favourable track via navigation buttons and press ok button to start playback 4 Press NEXT and PREVIOUS button to select track directly 5 Press REPEAT button change play mode KODAK PICTURE CD JPEG CD PLAYBACK Load a Kodak picture CD JPEG CD disc onto the disc tray then select picture function to play the disc with navigation left right button and press OK Button to confirm Slide show of Kodak Picture CD begins automatically Folders of JPEG picture CD are displayed on the TV screen use the navigation buttons to select the desired folder and then press OK button to confirm The files in this folder are displayed and you can select your favourable pictures using the up down navigation buttons and press OK button to start playback Preview of the picture resolution size date will be displayed while you scroll across the file names KODAK PICTURE CD JPEG CD OPERATIONS 1 PLAY MODES Press REPEAT button to change play mode During playback press STO
Download Pdf Manuals
Related Search