Audio-Technica ATH-BT03
Contents
1. power from the last charge remains charging will end sooner Connection diagram PC Micro USB When charging starts the blue LED blinks and the red LED lights When battery power is low A warning sound is heard and the red LED and the blue LED both blink at 0 5 second intervals When the battery becomes completely depleted an ending sound is heard and the power is automatically turned off When the LED start blinking charge the product according to the above instructions Operating time Continuous transmission including music playback time Max 6 hours Continuous standby time Max 200 hours X The above figures depend on operating conditions The following conditions during charging may cause the red LED to go off before charging completes At temperatures outside the operating temperature range 5 to 45 C The rechargeable battery is defective If this happens charge the battery again at the temperature range above If the battery still cannot be recharged contact your Audio Technica dealer The rechargeable battery may not operate long on the first charge and when it has been recharged after a long period after not being used After repeated charging and discharging it will become possible to adequately charge the battery The rechargeable battery has reached the end of its service life when battery operating time after charging shrinks to about half of what it first wa2. three seconds or longer will turn off the headsets Blue LED When the 3D BASS effect function is on the blue LED goes on for one second When the 3D BASS effect function is cancelled the red LED goes on for one second POWER EFFECT button Briefly press the button to turn on the 3D BASS effect function during music playback Pressing the POWER EFFECT button briefly again will result in two beep sounds and the red LED will go on for one second indicating the 3D BASS effect function has been cancelled x The 3D BASS effect may distort some types of music If this happens turn the 3D BASS effect function off Before making calls on a mobile phone with Bluetooth confirm the following The Bluetooth on the mobile is enabled This product and the Bluetooth mobile phone have been paired and set to use HSP or HFP 1 With this product in power off mode press and hold the POWER EFFECT button for three seconds or longer to turn the power on 2 Refer to the instruction manual of the transmitting Bluetooth device to connect the Bluetooth device ATH BTO3 appears in the list on the Bluetooth mobile phone screen When a Bluetooth mobile phone supporting HFP and HSP is used connect using HFP X For details on profiles see Supported Bluetooth version and profile gt page 2 Microphone Operation button Press the top or bottom of the button to adjust the sound volume E Receiving phone calls When t
3. INSTRUCTIONS audio technica Thank you for purchasing this headset Before using this headset please read through these operating instructions to ensure that you will use the headset correctly This device complies with Part 15 of FCC Rules and RSS Gen of IC Rules Operation is subject to the following conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation of this device You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment Note This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the
4. LED will blink three times as this product is turned on 3 Refer to the instruction manual of the transmitting Bluetooth device to connect the 1 Bluetooth device 4 Start playback on the transmitting Bluetooth device The blue LED blinks during Bluetooth connection The left earpiece has a protruding part Controlling a transmitting Bluetooth device If the transmitting Bluetooth device supports operation control functions Bluetooth profile AVRCP you can use the Operation button on this product to control the transmitting Bluetooth device Some transmitting Bluetooth devices may not support this function Operation button Operation function on transmitting device Briefly press the center the of the Operation button to play and pause a Press and hold the of the Operation button to l Briefly press Play Pause stop Press and hold Stop Briefly press the of the Operation button to Briefly press Forward Press and hold Fast forward forward tracks and press and hold for fast forward Briefly press Reverse Press Briefly press the ma of the Operation button to aaa ici reverse tracks and press and hold for fast backward To adjust the volume Press the top and bottom of the Operation button to adjust the sound volume Press the top of the Operation button to increase the sound volume and press the bottom to decrease it Pressing and holding the Operation button will al
5. Press and hold the Power Effect button for three seconds or longer Bluetooth devices that have been paired may have to be paired again under the following conditions When 9 or more Bluetooth devices have been paired The product allows pairing for up to 8 devices When you pair an additional device after having paired the product with 8 devices this pairing will overwrite the oldest pairing data When the pairing data in the product has been deleted due to a repair for example When connection history data in the other Bluetooth device has been deleted Listening to music This product supports SCMS T a content protection method for Bluetooth wireless technology It allows you to listen to music or audio from mobile phones One Seg TVs and other devices that support SCMS T Confirm the following before starting to use The transmitting Bluetooth device is on This product and the transmitting device have been paired The transmitting Bluetooth device supports the music transmission function profile A2DP gt For information on profiles refer to Supported Bluetooth version and profiles on page 2 1 Put on your headphones as shown in the figure on the right Place the left headphone marked L in your left ear and the right headphone marked R in the right ear 2 With this product in power off mode press and hold the POWER EFFECT button for three seconds or longer The startup chime sounds and the blue
6. ces Unless the earpieces properly fit the ear you will not hear the bass properly This product comes with four sizes of silicon earpieces XS S M and L The medium sized earpieces are attached to the earpieces at shipment The earpieces must fit the inner ear to provide a high quality music experience If the medium sized earpieces do not fit change to a size that does Cleaning procedure Remove earpieces from the headphones and clean them with a diluted detergent After cleaning dry before use Replacing earpieces Remove a worn earpiece and replace it with a new one as shown in the figure on the right Be sure to fully insert the earpiece so that it is flush with the base of the earpiece Z CAUTION The earpieces pick up dirt easily and should be regularly cleaned If the earpieces are no cleaned the sound producing parts may become contaminated and sound quality will degrade The earpieces are consumable parts and will deteriorate from storage and use Earpieces that no longer fit properly or show signs of wear should be replaced at the earliest opportunity Contact your Audio Technica dealer for purchasing consumables and other parts Make sure that a removed earpiece is properly installed on the earpiece before use Otherwise the earpiece could be lodged inside the ear and would have to be removed to prevent injury or disease Reset function If this product fails to respond to buttons bei
7. f any article is not supplied or is damaged contact your Audio Technica dealer e XS size x 2 pcs e009 e S size x 2 pcs 000 e M size x 2 pcs XS SML e L size x2 pcs Earpieces ER CKM55 This product is supplied with the M size earpieces on the product n Charging USB cable 1 0 m ATH BT03 Headset parts E Headphones Housing Earpieces Bushing External view Slider Reset button 60 cm cord For details see page 13 Operation button Use to listen to music E Control or make a call LED red Micro USB Call button LED blue jack Press to make a call x Paiting C5 button J Power Effect button Turns this product on and off Doubles as a 3D BASS effect mode switch For details see 3D BASS effect function on page 9 Release the cap from the claw Charging This product is not charged when purchased You must charge the product before you can start using it 1 Remove the cap from the product and connect the supplied USB charging cable to the micro USB jack 2 Correctly connect the USB charging cable to the USB port of a PC 1 3 When charging starts the blue LED blinks and the red LED lights After about three to four hours of charging the red LED will go off indicating that charging is completed 2 X 1 If the USB cable is not properly connected the red LED on the case blinks X 2 This is the time it normally takes to charge an empty battery If
8. he product operates up to 10 meters from a transmitting Bluetooth device however obstacles between the transmitting Bluetooth device and the product or the structure of the building you are in may reduce the operating distance Interference with other devices Microwave ovens digital cordless phones devices using wireless LAN Bluetooth devices and other devices using the same 2 4 GHz frequency band may cause dropouts Similarly since this product will also interfere with such devices it is essential that devices that are likely to interfere with each other are kept apart Note that Audio Technica accepts no liability whatsoever for leakage of data during Bluetooth transmission Supported Bluetooth version and profile This product supports the following Bluetooth version and profile E Communication system Bluetooth Ver 2 1 EDR E Compatible Bluetooth Profiles e A2DP Advanced Audio Distribution Profile Sends and receives stereo quality audio data e AVRCP Audio Video Remote Control Profile Play stop skip volume control and other AV device controls e HSP Headset Profile Making calls receiving incoming and making outgoing mobile phone calls e HFP Hands Free Profile Making hands free calls and receiving incoming and making outgoing mobile phone calls with hands free Verifying package contents Before you start using the product make sure that all the following articles have been supplied I
9. here is an incoming call a ring toneis 2 heard from the headphones Press the Call button to take the call X Press and hold the Call button for two seconds or longer to reject a call E Making a call Use your mobile phone to make a call If you cannot hear the dial tone from this product press and hold the Call button for two seconds or longer Power Effect button E Redialing a call Press and hold the Call button for two seconds or longer when the mobile phone is in standby mode The phone dials last dialed number again The procedure for redialing may differ depending on mobile phone Use the top and bottom part of the Operation button to adjust the sound volume E Ending a call Press the Call button on this product to end the call After use Set the transmitting Bluetooth device to disconnect Bluetooth connection After use press and hold the POWER EFFECT button for three seconds or longer to turn this product off Receiving a call during music playback Calls during music playback To call during music playback requires not only A2DP but also HFP or HSP Bluetooth connection 1 Use the steps described under Making calls on page 10 using HFP or HSP to make a Bluetooth connection from your mobile phone x For details refer to the instruction manual supplied with your mobile phone 2 Operate the Bluetooth device portable player or mobile phone that plays back music to establish a Bluetooth connection
10. ng pressed for example use the Reset button to clear up the problem Use the steps below to reset this product using the Reset button on the right side of the controller 1 Reset this product 2 Insert a thin stick in the reset hole and press as shown in the figure on the right until you can feel the Reset button has been pressed Pressing the reset button will turn off this product X This operation will not delete pairing data Troubleshooting Guide Q1 The power does not go on A1 Check whether the battery is properly charged A2 Check whether the battery is recharging The power will not go on during charging Q2 Pairing is not possible or does not complete A1 Check whether this product and the other Bluetooth device are placed too far apart gt Place this product and the other Bluetooth device within one meter of each other and perform pairing again A2 Check whether the other Bluetooth device is a compatible device Check compatibility A3 Check whether profiles have been set up gt Refer to the instruction manual of the other Bluetooth device to complete the profile setup on that device Q3 A Bluetooth connection cannot be made A1 Check whether this product and the other Bluetooth device are powered up gt If not on turn them on A2 Check whether the Bluetooth function on the other Bluetooth device is enabled gt Enable the Bluetooth function Q4 N
11. o music output A1 Check whether this product and the other Bluetooth device are powered up gt If not on turn them on A2 Check whether this product and the other Bluetooth device are connected using A2DP gt Connect using A2DP A3 Check whether the other Bluetooth device is playing back music gt Set it to play back music A4 Check whether the sound volume on this product or the connected device is too low gt Turn up the sound volume 3 Q5 The music is distorted and plagued by dropouts A1 Check whether there is a microwave oven or wireless device operating on the 2 4 GHz wave band near this product or the other Bluetooth device gt If there is move them further away A2 Check whether the 3D BASS Effect function is on gt The 3D BASS Effect may distort some music sources If this happens turn the 3D BASS Effect function off A3 Check whether multiple applications are running on the other Bluetooth device gt Some mobile phones when connected to this product may cause dropouts in music and speech if multiple applications are simultaneously running on the phone A4 Check if the other Bluetooth device is too far away gt Move the other Bluetooth device within transmission distance of this product Q6 Poor music sound quality A1 Confirm whether this product and the other Bluetooth device have connected using HSP gt Switch Bluetooth connection to A2DP Q7 The other part
12. on for three seconds or longer The blue LED will blink three times as the product is turned on 3 Press and hold the Pairing button for three seconds or longer to activate the pairing mode A beep sound will be heard to indicate that pairing has started The red and blue LEDs will blink alternately during pairing XPairing may take a while 4 Perform pairing on the other Bluetooth device to find the product The screen of the other Bluetooth device will display a list of found devices This product will appear as ATH BT03 on the screen 5 Select ATH BT03 displayed on the screen of the other Bluetooth device When you are prompted for a pass code on the screen of the other Bluetooth device enter 0000 When the blue LED changes to slow blinking pairing is complete XTo connect to multiple profiles the paring procedure in steps 4 and 5 will have to be repeated several times X Some devices perform Bluetooth connection automatically to load a compatible profile For details refer to the instruction manual supplied with your mobile phone If pairing is not completed within five minutes the product will terminate pairing mode and shut down Should this happen perform the pairing procedure again The Reset button gt page 13 cannot be used to delete pairing data Operation during pairing The red and blue LEDs will blink alternately during pairing Press and hold the Pairing button for three seconds or more
13. receiver is connected Consult the dealer or an experienced radio TV technician for help Bluetooth devices This product uses the 2 4 GHz frequency band Be sure to read and observe the following instructions to prevent interference with other devices using this frequency band The frequency band used by the product is also used by microwave ovens and other industrial scientific and medical instruments as well as short range wireless base stations for identifying mobile devices requires a license on plant production lines specified low power base stations does not require a license and amateur radio stations requires a license 1 Before using this product make sure there are no short range wireless base stations for identifying mobile devices specified low power base stations or amateur radio stations nearby 2 In the unlikely event that use of this product causes serious interference with a short range wireless base station for identifying mobile devices stop transmitting radio waves immediately Then contact your Audio Technica dealer regarding interferences countermeasures for example installing partitions etc to prevent interferences 3 Also contact your Audio Technica dealer regarding other problems involving serious interference with a short range wireless base station for identifying mobile devices and amateur radio stations or questions regarding such interference Available operating range T
14. s Contact your Audio Technica dealer to have the rechargeable battery replaced Do not expose the battery to sudden temperature changes direct sunlight condensation sand dust or electrical shocks Never leave it in a parked car The battery will not be properly charged if the product or the PC enters an energy saving mode during charging Check PC settings before connecting the product to a PC The red LED will go off automatically also when the PC enters an energy saving mode Should this happen recharge the battery Connect the product directly to the PC using the supplied USB cable Do not use a USB hub or USB extension cable to connect to a PC Be sure to fully insert the plug of the USB cable into the USB port Note Lithium polymer rechargeable battery is used for this headset When disposing of this headset please comply with local regulations Use this procedure to pair devices beforehand to allow them to communicate with each other Bluetooth devices should first be paired before connection To hear the verifying beep of pairing put on the headphones before you start the pairing procedure For information on how to put on the headphones see Listening to music on page 7 Also read the instruction manuals supplied with the products that are to be connected Place the Bluetooth devices within one meter of each other 2 With the product in power off mode press and hold the Power Effect butt
15. so allow you to adjust DOWN the volume A warning beep is heard when maximum or minimum sound volume is selected and the sound cannot be set any higher or lower Sound volume adjustment using Operation button Press the top of the button to increase sound volume and press the bottom of the button to lower it 5 Turn off this product when you are through listening Set the transmitting Bluetooth device to disconnect Bluetooth connection After use press and hold the Power Effect button for three seconds or longer to turn this product off The ending chime is heard and this product is turned off Continued on overleaf 3D BASS effect function Use the POWER EFFECT button to turn the 3D BASS effect function on and off The 3D BASS effect function employs SRS WOW HD technology developed by SRS Labs Inc x The 3D BASS effect function is turned on by default WOW HD significantly improves the playback quality of audio delivering SiIS a dynamic 3D entertainment experience with deep rich bass and high WOW HD frequency clarity for crisp detail S is a trademark or registered trademark of SRS Labs Inc WOW HD technology is incorporated under license from SRS Labs Inc Using 3D BASS effect function Briefly press the POWER EFFECT button during music playback a beep is heard and the blue LED goes on for one second X The 3D BASS effect function is turned on by default Pressing and holding the Effect button for
16. using A2DP with this product Redialing during music playback Operation button Press the top or bottom of the button to adjust the sound volume Press and hold the Call button for two seconds 2 or longer during music playback to redial The music pauses while a call is made to the last dialed phone number When an incoming call is received the music pauses and the ring tone is heard from the headphones of this product 1 Press the Call button on this product to take the call 2 When the call ends press the Call button to end it This product resumes music playback Call button If the ring tone cannot be heard during music playback use the following steps Pause music playback When the ring tone is heard press the Call button to take the call a Get into the habit of regularly cleaning your headphones to ensure that they will last for a long time Do not use alcohol paint thinners or other solvents for cleaning purposes E Controller To clean wipe with a dry cloth E Headphones ll Side view of headphones To clean wipe with a dry cloth Do not touch the parts used for sound reproduction x see figure at right as they are delicate Damage to the headphones may result E Cords X Sound Wipe away perspiration and any other dirt with a dry cloth after producing use part Cords that are not cleaned may deteriorate and cause a malfunction E Earpieces Size and type of earpie
17. wer Class2 Maximum communication range Line of sight approx 10 m Frequency band 2 4 GHz band 2 402 GHz 2 480 GHz Compatible Bluetooth Profiles A2DP AVRCP HFP HSP Support Codec SBC Supported content protection SCMS T method DC3 7V Built in lithium polymer rechargeable battery Electret condenser Omnidirectional Power source Microphone element Microphone direction characteristic Microphone sensitivity 40 dB 1 V Pa at 1 KHz Microphone effective frequency 10 4 000 Hz range Dimensions W19xH64xD25 mm excluding projecting parts Weight Approx 15 g 5 C to 45 C USB charging cable Earpieces XS S M L ER CKM55 XS S M L Operating temperature Accessories Spare earpieces available separately Headphones Driver Dynamic 8 8 mm Output sound pressure level 100 dB mW Frequency response 20 20 000Hz Impedance 16 Q Cord length 60 cm Y type Weight Approx 6 g including cord For product improvement this product is subject to modification without notice The Bluetooth word mark and logos are owned by the Bluetooth SIG Inc and any use of such marks by Audio Technica Corporation is under license All other trademarks are property of their respective owners audio technica Audio Technica Corp 2206 Naruse Machida Tokyo 194 8666 Japan 2011 Audio Technica Corp
18. y cannot be heard during a phone call A1 Check whether this product and the Bluetooth mobile phone of the other party are powered up gt If not on turn them on A2 Confirm whether this product and the other Bluetooth device have been connected using HFP or HSP gt Make Bluetooth connection using HFP or HSP A3 Confirm whether the voice setting of the Bluetooth mobile phone of the other party is set to use this product during a call gt Set the voice setting of the Bluetooth mobile phone to use this product A4 Check whether this product sound volume is set too low gt Turn up the sound volume A5 Check whether the sound volume of the connected mobile phone is set too low gt Turn up the sound volume Q8 Transmission distance during a call is too short A1 A microwave oven or wireless equipment using the 2 4 GHz band are used near this product and the other Bluetooth device gt Place the devices further apart A2 Place this product closer to the other Bluetooth device Q9 Cannot charge A1 Confirm whether the USB cable between this product and the PC is properly connected gt Be sure to fully insert the cable plugs A2 Confirm whether the PC is turned on gt Turn on the PC A3 Confirm whether the PC is in sleep mode gt Check PC power settings Specifications Control Communication System Bluetooth Version 2 1 EDR Output Bluetooth Specification Po
Download Pdf Manuals
Related Search