EK Water Blocks 3831109856024
Contents
1. liquid cooling tubes and connect the water block s into the cooling circuit while holding the M3 nut with your thumbs firmly EKWB recommends using EK PSC fittings with the EK FC570 GTX SE series water blocks To ensure that the tubes are securely attached to the barb fittings please use hose clamps or an appropriate M3x6 screw substitute The use of an algaecide is always recommended for any liquid cooling system You can use any opening as an inlet outlet port EK PSC Fitting High Flow Fitting HIGH FLOW FITTING Carefully lift your card with installed block and insert it in your PC case Please bear in mind that your card suddenly withstands extra weight thus again be very careful not to bend it or cause any other unneeded moves that might damage your card or block during installation REQUIRED TOOLS AND MOUNTING SCREWS Scissors philips screwdriver 13 x screws M3x4 DIN7985 1 x M3x6 DIN7985 14 x PVC washers Val thermal grease All disclosures notices and warranty conditions are being written on the EKWB website Please read terms of use Released on 17 of August 2011 Revision 1 0 1 x M3 nut2. the original heat sink after removing all screws should be removed There are 17 screws on the back of the graphic card fasteners securing it to the board and bracket Wipe off the remains by using non abrasive cloth or Q tip as shown on sample photo of the original thermal compound until the components and circuit board are completely clean EKWB does not recommend using any liquids for removing paste E ones tae be a a na then a 8 j Fi iil il Ti TO i mn m LY i q A MEDknintnnnes e EEEE E 3 ee oe ee ee ae ee zs s LJ b Vy z 0 Mmufoctured efter 18 F E oe Q y u a a Aa A a Rea Bane 3 APPLYING THERMAL COMPOUND Apply thermal 4 CUTTING THERMAL PADS Your block comes with thermal pads some of which are already pre cut Others have compound lightly coat nVidia GF110 GPU chip with for to be cut to smaller chunks in order to cover all the VRM components such as MOSFETs and inductors chokes example Arctic Cooling MX 2 or MX 4 thermal PLEASE REMOVE THE PROTECTIVE FOIL FROM BOTH SIDES OF THE THERMAL PADS PRIOR TO INSTALLATION grease EKWB recommends to apply thermal grease in cross form for best performance see sample picture Thickness 1mm for memory Thickness 0 5mm for VRM MOSFETS and inductors R30 STEP 3 INSTALLING WATER BLOCK 1 PLACING THERMAL PADS ON PCB Place thermal pads on chips so that numbers on chips 2 PLACING GPU REINFORCE PLAT
3. E ON PCB Place metal reinforce and washer on match size of thermal pads EKWB made sure users have more than enough pads to cover PCB as shown on picture below and screw it in with enclosed M3x4 screws Please all surfaces that need to be covered to make block fully functional EK recommends using use encased PVC washers under each screw Make sure you use fasten screws small drops of electrically non conductive for example Arctic Cooling MX 2 or MX 4 equally and do not use too much force thermal grease on each phase regulator that is being covered with thermal pad in order to even further improve the thermal performance of the EK FC570 GTX SE series water block ong a bail rae at 3 c ye A O N TORR EA be Washer _ oonn TTTS Orientation of reinforcer is important E FETT x Sag Ea ony GF110 275 A1 m f a Ia Eo i ka pritnin amp pA iE imu K A aol I a n A CORET 1a ape AA EVIA ETAR PVC washer All disclosures notices and warranty conditions are being written on the EKWB website Please read terms of use Released on 17 of August 2011 Revision 1 0 3 PLACING STANDOFFS ON BLOCK Brass standoffs are obligatory in order to attach this 4 PLACING BLOCK TO GRAPHIC CARD During this process please make sure you water block to the printed circuit board of the graphics card Please use the enclosed key to screw them to the copper base
4. ekwD Installation and mounting manual for EK FC570 GTX SE water block This product is intended for installation only by expert users Please consult with a qualified technician for installation Improper installation may result in damage to your equipment EK Water Blocks assumes no liability whatsoever expressed or implied for the use of these products nor their installation The following instructions are subject to change without notice Please visit our web site at www ekwaterblocks com for updates Before installation of this product please read important notice disclosure and warranty conditions printed on the back of the box or our home page The barb hose fittings require only a small amount of force to screw them in otherwise the high flow fittings might break These fittings do not need to be tightened with much force because the liquid seal is made using o rings The use of an algaecide and corrosion inhibitors is always recommended for any liquid cooling system STEP 1 GENERAL INFORMATION Sample picture of GeForce 570 GTX HD graphics card PCB NVA P1263 STEP 2 PREPARING YOUR GRAPHIC CARD 1 REMOVING STOCK COOLER Remove encircled screw on the bracket required only on certain models M i we Y u oe u u GF110 275 A1 ne F umy J STEP 2 cont PREPARING YOUR GRAPHIC CARD 1 cont REMOVING STOCK COOLER Remove all encircled screws All heat sink assembly 2 CLEANING THE PCB Carefully detach
5. of the water block pay attention not to scratch surface Brass M4 M3 Standoff key 3 9mm standoff align holes on PCB with holes on block Also pay attention not to use too much force by pressing block down to PCB Chip dies are prone to cracking 5 ATTACHING BLOCK TO GRAPHIC CARD By using Philips screwdriver screw in enclosed M3x4 DIN7985 screws EKWB recommends start screwing the screws around the GPU core and continue outwards e Tightening the standoffs O Use 9 enclosed PVC washers Temporarily remove the water block to check for uniform surface contact between the block and the components Note the pattern of contact on a piece of paper Then repeat substeps in previous section to reattach the block In case you fail to obtain good contact please check again your thermal pad thickness or contact our support service Use one M3x6 screw one PVC washer and one M3 nut to secure the I O Please use spacer only on copper base if you use fitting with G1 4 thread longer than 5mm see also known as PCI bracket firmly to the circuit board This will allow the sample picture Screw in the fittings and plugs use spacers on copper base in case you have computer chassis to carry the weight of the waterblock thus reducing the fittings with G1 4 thread longer than 5mm Use 6mm allen key to screw in and tighten new EK tension on the PCI express slot Tighten the screw with Philips screwdriver Plug G1 4 Attach the
Download Pdf Manuals
Related Search