Shuttle X50V3L
Contents
1. X50V3L Series Quick Guide English Front Rear Side View Shusttle Placing on the desk m To place the machine on the desk and to carry it do the following a ma i n Sooo 10000010000010000000000 Powering on the system E Follow the steps 1 3 below to connect the AC adapter to the DCIN jack Press the Power Button to turn on the system Cleaning the screen m Follow these guidelines for cleaning the outside and handling the screen of the computer Turn off the system and disconnect all cables Use a damp or cleaning cloth soft lint free cloth with gentle water only and gently wipe the screen surface Do not spray liquid directly on the screen Note The product s color and specification will depend upon the actually shipping product j fi a a 1 ft ADA AAD Ltd ttt nr i ff J fy j fey i fy P fs T i 17 19 20 21 22 Stand Handle Power Button Microphone Stylus pen Webcam SD card reader LCD Display Single Touch Non Touch Optional Microphone Jack A WiFi LED Y Headphone Line out Jack Q Harddisk drive LED 8 LAN Port a Power LED y4 USB 2 0 Ports Stereo speakers Stand Handle Touch left click on the mouse Jm i tu SN TRR i ia iY f E HDMI Port som USB 2 0 Ports vcAPot J Power Input DCIN Printer Port Optional2. USB Controller E program and correct 4 point tion n screen with the Edge Compensation Hardware About SS 2 General Setting Display panel Linearization Curve Click Start All Programs eGalax Touch Configure Utility Select Tools tab and click 4 Points Calibration Clear linearization parameter and do 4 points alignment E When the 4 points calibration completed press OK to continue Safety Information a xtkutility Read the following precautions before setting up a Shuttle XSOV3L CAUTION i l 4 points calibration completed Press Ok to continue Do not walk on the power cord or allow anything to rest on it The warranty does not apply to the products that have been disassembled by users CAUTION Danger of explosion if battery is incorrectly replaced Replace only with the same or equivalent type recommended by the manufacturer Dispose of used batteries according to the manufacturer s instructions A Begin Installation 2 Unscrew three screws of the bracket and remove it 4 Carefully push down the memory module until it snaps into the locking mechanism 3 Mount HDD into the bracket with four screws 5 Repeat the above steps to install additional memory modules A For safety reasons please ensure that the power if required cord is disconnected before opening the case 1 Remove the cover on the bac
3. COM Ports Optional Kensington Lock Port How to use the Touch Panel Optional Touch and hold right click on the mouse X50V3L first Unscrew 4 screws of the stand mount and remove the stand mM X50V3L brings digital life for an easy touch experience Experience the ease of Place the X5OV3L on a flat surface such as a table Picture 1 and pull the stand managing your digital life with a few touches or the use of the stylus pen The upwards to an angle of 30 Picture 2 To carry or move your X50V3L fully extend touch of your finger replaces the mouse and is all you need to interact with the the angle to 180 Picture 3 XSOV3L Somes UNIT The VESA standard lets users mount it on to walls easily Please refer to the user guide of the wall arm mount kit you bought to install it lf you are mounting your X5OV3L to the wall remove the cover on the back of Note X5OV3L can be mounted to a wall using a VESA compatible 100 x 100mm wall arm bracket 62R X50V31 0601 X50V3L English Spanish Korean WI see Shuttle French German Quick Guide 4 Point Calibration Optional E Touch and hold the center of the target Repeat on four corners and the screen will adjust automatically m Run the screen calibration gt eGalaxTouch
4. k of X50V3L first unscrew four screws of the stand mount and remove the stand DIMM2 DIMM1 4 As shown install the HDD amp bracket in the chassis and push it towards the direction as indicated by the red arrow to connect the HDD connector 5 Tighten the HDD amp bracket with three screws 6 Replace the VESA Base and refasten four screws Screw VESA Base Stand Handle HDD 2 Unscrew four screws of the back cover and remove it Connector C Memory Module Installation A If you install only one memory module in your system install it in the slot labeled DIMM2 1 Locate the SODIMM slot on the mainboard 2 Align the notch of the SODIMM slot memory module with the one of the memory slot B HDD Installation 1 Unscrew four screws of the VESA Base and remove it first Back Cover Screw ar ende 2 Replace the cover complete 3 Gently insert the module into the slot in a 45 degree angle VESA Base bere TTL 53R X50V33 2501
Download Pdf Manuals
Related Search