Chief CMS490 projector accessory
Contents
1. Grounding label Figure 13 CMS490 Installation Instructions WARNING RISK OF ELECTROCUTION All electrical wiring required for installation should be installed by a qualified electrician IMPORTANT The appropriate outlet being installed must be the grounding type and properly grounded in accordance with all local codes and ordinances 3 Wire outlet into junction box in accordance with all local codes and ordinances Adding Components 1 Open and lower door on CMS490 2 Loosen but do NOT remove four thumb nuts on component tray See Figure 14 3 Slide tray and lower to remove from CMS490 See Figure 14 Figure 15 Component tray Figure 14 Add components to component tray Lift component tray to CMS490 ensuring all power and signal wires and cables are properly installed on the tray See Figure 15 Slide component tray to narrow end of thumb nut openings Fasten tray into place by tightening four thumb nuts Close CMS490 door and lock in place 10 Installation Instructions CMS490 11 CMS490 CHIEF Our Mounts Your Vision Chief Manufacturing a products division of Milestone AV Technologies 8800 002117 Rev00 2011 Milestone AV Technologies a Duchossois Group Company www chiefmfg com 11 11 USA International Europe Asia Pacific TUDD TTU D T U Installation Instructions 8401 Eagle Creek Parkway Savage MN 55378 800 582 6480 952 894 6280 877 894 62. N to ceiling framework using one 10 24 x 1 2 Phillips head screw D through each track clip D at each corner See Figure 3 Figure 2 Figure 3 CMS490 Ceiling Framework CMS490 Installation Instructions Securing CMS490 Frame to Ceiling Structure 1 Examine ceiling structure concrete steel truss or wood above CMS490 frame N to identify four support cable anchor locations Each location should be approximately 15 outside of support holes in CMS490 frame N Mark locations with pencil See Figure 4 Figure 5 2 Tap anchor KC into each hole to a depth of at least 1 See Figure 5 WARNING Failure to properly set anchor may result in failure of anchor and serious personal injury or damage to equipment 3 Using claw portion of hammer set each anchor KC by pulling it out of hole approximately 1 4 See Figure 5 4 Insert portion of manufactured loop on cable KA through Solid Concrete Ceiling Structure hole in anchor KC and insert end of cable KA through loop Repeat for 3 remaining support locations See Figure 5 WARNING Anchors must be installed into structurally Steel Truss Ceiling Structure sound solid concrete with a minimum thickness of 1 75 44 5mm or greater Installation into hollow concrete block 1 Route end of cable KA over truss at marked cable anchor support location and then through cable loop Repeat for 3 mortar or concrete that exhibits cracking spal
3. 918 952 894 6918 Franklinstraat 14 6003 DK Weert Netherlands 31 0 495 580 852 31 0 495 580 845 Office No 1 on 12 F Shatin Galleria 18 24 Shan Mei Street Fotan Shatin Hong Kong 852 2145 4099 852 2145 4477
4. INSTALLATION INSTRUCTIONS Ceiling Tile Storage Kit GCHIEF CMS490 Our Mounts Your CMS490 DISCLAIMER Milestone AV Technologies and its affiliated corporations and subsidiaries collectively Milestone intend to make this manual accurate and complete However Milestone makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind Milestone makes no representation of warranty expressed or implied regarding the information contained herein Milestone assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document Chief is a registered trademark of Milestone AV Technologies All rights reserved A IMPORTANT SAFETY INSTRUCTIONS WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions WARNING Failure to read thoroughly understand and follow all instructions can result in serious personal injury damage to equipment or voiding of factory warranty It is the installer s responsibility to make sure all components are proper
5. RY OR DAMAGE TO EQUIPMENT It is the installers responsibility to make certain the structure to which the kit is being mounted is capable of supporting five times the weight of the kit and all attached equipment Reinforce the structure as required before installing the kit NOTE The following instructions assume a suitable mounting structure and surface exists prior to installation IMPORTANT This kit must be grounded If there is a malfunction or break down of any components grounding provides a path of least resistance for electric current to reduce the risk of electric shock Grounding Instructions This product must be connected to a grounded metal permanent wiring system and must be properly installed and grounded in accordance with all local codes and ordinances This product is suitable for use in Other Environmental Air Spaces in Accordance with Section 300 22 C of the National Electrical Codes 2008 1 Attach one of the grounding wires M using one 10 32 grounding nut P between the door and the CMS490 box at one of the points marked with grounding labels See Figure 12 2 The other grounding wire M should be attached between the removable tray and the CMS490 box using one 10 32 grounding screw E in desired location on removable tray and one 10 32 grounding nut P See Figure 13 CMS490
6. astener Drill Hole Loosen Fastener By Hand Aflojar elemento de fijaci n Phillips Screwdriver Open Ended Wrench Destornillador Phillips Llave de boca Gabelschlussel O CMS490 TOOLS REQUIRED FOR INSTALLATION 1 4 concrete 5 32 wood K 1 CMS490 Securement Kit KB 4 Cable support S KD 4 0 262 x 1 5 16 1 KA 4 1 16 x 25 Wire cable M 2 Grounding wire assembly BAG C C 2 10 24 x 1 2 D 4 10 24 x 1 2 BAGE E 2 10 32 x 3 8 Installation Instructions F 4 06 32 x 1 2 BAG G G 2 08 32 1 4 J 1 Outlet box attachment plate Installation Instructions PREPARING FOR INSTALLATION Installation Requirements The CMS490 has been designed to be mounted recessed into Ceiling Framework a suspended ceiling consisting of 2 x 2 ceiling tiles and secured by a WireVice system Preparing Framework 1 Attach track clips 2 left A 2 right B one at each corner of the CMS490 frame N using one 06 32 x 1 2 Phillips flat head screw F on each clip See Figure 1 Figure 1 Installing CMS490 Framework 1 Remove one 2 ft x 2 ft tile from ceiling 2 Insert CMS490 frame N with attached brackets into the empty ceiling space See Figure 2 3 Set CMS490 frame N over top of ceiling framework hooking each track clip A and B onto the ceiling framework See Figure 3 4 Secure CMS490 frame
7. ling or other remaining support locations See Figure 6 defects may result in failure of anchor and serious personal injury or damage to equipment 1 Drill 1 4 diameter x 1 1 8 deep pilot hole at each marked cable anchor support location Ensure hole is at least 2 1 2 from nearest concrete edge Remove debris from hole See Figure 5 Figure 6 Installation Instructions Wood Ceiling Structure WARNING Anchors must be installed into wood with a minimum thickness of 1 1 2 38 1 mm or greater 1 Drill a 5 32 diameter x 1 1 2 deep pilot hole at each marked cable anchor support location Ensure hole is at least 5 8 from nearest wood edge Remove debris from hole See Figure 7 Figure 7 Fully thread eye lag KD into each hole See Figure 7 Route end of cable KA through eye lag KD and then through cable loop Repeat for 3 remaining support locations See Figure 7 Figure 8 CMS490 Installing Cable to CMS490 Frame CAUTION Failure to properly tension cables KA may result in damage to ceiling tile framework 1 Threadeach cable KA completely through cable lock KB corresponding hole in corner of CMS490 frame N and completely through opposite side of cable lock KB See Figure 8 2 Adjust cable tension until CMS490 frame N is supported entirely and evenly by all four support cables but not so tight as to distort ceiling tile framework CAUTION Cable lock KB will al
8. low cable to enter from only one direction per side indicated by arrows on lock Depress spring loaded pins on cable lock KB to release cable tension Installing Electrical Box and Outlet 1 Install Listed electrical box not included to outlet box attachment plate J 2 Install the plate J with attached electrical box onto the CMS490 frame N using two 8 32 x 1 4 Phillips screws G See Figure 9 electrical Figure 9 CMS490 Installation Instructions Placing CMS490 Into Ceiling Structure 1 Orient CMS490 so that the electrical opening lines up with the outlet box attachment plate J on the CMS490 frame See Figure 10 2 Lift CMS490 L into place through the CMS490 frame N See Figure 10 3 Lower onto CMS490 frame carefully lining up outlet box attached to CMS490 frame with opening in CMS490 See Figure 11 4 Secure the CMS490 L to the CMS490 frame N using four 8 32 x 1 Phillips head screws H two in the front and two in the back of the CMS490 See Figure 11 5 Secure the outlet box attachment plate J to the CMS490 using one 8 32 x 1 Phillips head screw H See Figure 11 Electrical Opening Figure 10 NOTE Ensure that there are four audible clicks each corner hook clicking into place onto the frame See Figure 11 Corner Hook Figure 11 Installation Instructions WARNING IMPROPER INSTALLATION CAN LEAD TO KIT FALLING CAUSING SEVERE PERSONAL INJU
9. ly assembled and installed using the instructions provided WARNING Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment Reinforce the structure as required before installing the component WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of all components and the CMS490 does not exceed 50 Ibs 22 7 kg Installation Instructions WARNING Use this mounting system only for its intended use as described in these instructions Do not use attachments not recommended by the manufacturer WARNING Never operate this mounting system if it is damaged Return the mounting system to a service center for examination and repair WARNING Do not use this product outdoors SAVE THESE INSTRUCTIONS Installation Instructions CMS490 DIMENSIONS DOOR HIDDEN DIMENSIONS MILLIMETERS INCHES LEGEND Tighten F
Download Pdf Manuals
Related Search