Chief K3F310B flat panel desk mount
Contents
1. Installation Instructions K3F310 CAUTION Using screws of improper size may damage your display Proper screws will easily and completely thread Center faceplate 3 into display mounting holes array stand not shown for clarity 3 Using Phillips screwdriver carefully install two selected ZA screws J or H through selected spacers L or M into the 0 253 upper mounting holes the display Thread screws completely into display then back out 3 complete turns See Figure 7 4 Pickup and align display so that screws installed on the back of the display in the previous step fit into the mounting holes on the faceplate Lower the display firmly into place See Figure 7 Figure 8 7 Tighten all four screws Do not overtighten Adjustments Pivot Adjustment 1 Array arms may pivot toward the front of mount up to 15 per arm See Figure 9 WARNING Pivoting array arms toward the back of mount may cause K3F310 mount to tip over causing serious Center faceplate personal injury or damage to equipment Do not pivot arms array stand not shown for clarity toward back of mount See Figure 9 Figure 7 top view 5 Slide two remaining selected spacers L or M in between faceplate and display positioning them over the ower two mounting holes See Figure 8 6 Install two remaining selected screws J or H through lower t2. Sicherheitsschl ssel Chave de seguran a Chiave di sicurezza Veiligheidssleutel Cl de s curit 10 Installation Instructions TOOLS REQUIRED FOR INSTALLATION e 3 16 included 5 32 included C 1 table top base A 1 3 array assembly B 3 cable management cover 22 F 4 G 6 D 1 column cap E 1 1 4 20 11 4 bumper base cover e e e H 12 J 12 12 M4x30mm M4x20mm M4x12mm GC Li N 1 1 Q 1 5 16 3 16 5 32 Installation Instructions K3F310 Assembly And Installation 1 Usefour1 4 20 1 1 4 flat head cap screws F to secure table top base C to array assembly A See Figure 1 NOTE Make sure front of base long legs is on the display side when attaching base to array See Figure 1 front of base Figure 1 2 Carefully manipulate base cover E to create an opening large enough to wrap cover around array column See Figure 2 3 Wrap base cover around column and slide it down until base cover fits securely onto table top base C See Figure 2 d Figure 2 4 Snap column onto top of array assembly See Figure 3 5 Figure 3 Apply bumpers G to unders
3. INSTALLATION INSTRUCTIONS Triple Dual Array Table Top Stand S CHIEF K3F310 Our Mounts Your Installation Instructions K3F310 DISCLAIMER Milestone AV Technologies and its affiliated corporations and subsidiaries collectively Milestone intend to make this manual accurate and complete However Milestone makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind Milestone makes no representation of warranty expressed or implied regarding the information contained herein Milestone assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document Chief is a registered trademark of Milestone AV Technologies All rights reserved A IMPORTANT SAFETY INSTRUCTIONS WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions DIMENSIONS WARNING Failure to read thoroughly understand and follow all instructions can result in serious personal injury damage to equipment or voiding
4. See Figure 5 Center faceplate array stand not shown for clarity Figure 5 3 Pickup and align display so that screws installed on the back of the display in the previous step fit into the mounting holes on the faceplate Lower the display firmly into place See Figure 5 4 Using Phillips screwdriver install two M4x12 mm Phillips pan machine screws K through the lower mounting holes on faceplate into the display See Figure 6 Center faceplate oQ x 2 array stand not shown for clarity Figure 6 5 Tighten all four screws Do not overtighten NOTE If roll adjustment is desired for center faceplate do not tighten screws 6 Repeat Steps 1 5 for outside displays 7 Proceed to Cable Management Section Recessed Mounting Holes NOTE If faceplate does not fit into recessed area of display proceed with the steps in this section 1 Determine depth of recessed mounting holes relative to back surface of display against which faceplate will contact 2 Select proper length spacer and screw from table below NOTE All spacers used should be the same length If the recess depths result in multiple spacer lengths then select the longer spacer IF recess DEPTH is THEN use spacer AND screw 3 8 or less L 3 8 long J M4 x 20mm More than 3 8 up to M 3 4 long H M4 x 30mm and including 3 4
5. allation Instructions GS CHIEF Our Mounts Your Vision Chief Manufacturing a products division of Milestone AV Technologies 8800 002254 Rev00 2012 Milestone AV Technologies a Duchossois Group Company www chiefmfg com 10 12 USA International Europe Asia Pacific gt TU 6436 City West Parkway Eden Prairie MN 55344 800 582 6480 952 225 6000 877 894 6918 952 894 6918 Franklinstraat 14 6003 DK Weert Netherlands 31 0 495 580 852 31 0 495 580 845 Office No 1 on 12 F Shatin Galleria 18 24 Shan Mei Street Fotan Shatin Hong Kong 852 2145 4099 852 2145 4477 SCH 52 d D
6. ide of table top base C See Figure 4 Figure 4 K3F310 Installation Instructions Display Installation WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of all components located on the K3F310 up to and including the display does not exceed 15 105 6 8 kg per display CAUTION Using screws of improper size may damage your display Proper screws will easily thread into display mounting holes NOTE Supplied screws H J and K may not fit properly for all displays See displays operating instructions for details Flush Mounting Holes IMPORTANT Always install center display FIRST in order to prevent stand from tipping If only using two displays remove center faceplate assembly and be sure to support opposite arm when mounting displays to prevent stand from tipping NOTE Set height of center display prior to installing display See Height Adjustment Section for details Center of display must be at least 18 above desk surface 1 Position faceplate in desired mounting position Adjust as required before proceeding See Height Adjustment Section for details 2 Using Phillips screwdriver carefully install two M4 x 12mm Phillips pan machine screws K into the upper mounting holes on the display Thread screws completely into display then back out 3 complete turns
7. iz Stiftmarkierung Marcar com lapis Segno a matita Potloodmerkteken Marquage au crayon Loosen Fastener Aflojar elemento de fijaci n Befestigungsteil l sen Desapertar fixador Allentare il fissaggio Bevestiging losdraaien Desserrez les fixations Drill Hole Perforar Bohrloch Fazer furo Praticare un foro Gat boren Percez un trou Phillips Screwdriver Destornillador Phillips Kreuzschlitzschraubendreher Chave de fendas Phillips Cacciavite a stella Kruiskopschroevendraaier Tournevis a pointe cruciforme Adjust Ajustar Einstellen Ajustar Regolare Afstellen Ajuster Open Ended Wrench Llave de boca Gabelschl ssel Chave de bocas Chiave a punte aperte Steeksleutel Cl fourche Remove Quitar Entfernen Remover Rimuovere Verwijderen Retirez By Hand A mano Von Hand Com a m o A mano Met de hand la main Optional Opcional Optional Opcional Opzionale Optie En option C y 4 d 3 Hex Head Wrench Llave de cabeza hexagonal Sechskantschlussel Chave de cabe a sextavada Chiave esagonale Zeskantsleutel Cl a t te hexagonale D 80 Security Wrench Llave de seguridad
8. n adjusted arm to lock position See Figure 12 Figure 12 Faceplate Assembly Removal Center Faceplate NOTE Center faceplate may be removed to create a 2 x 1 display solution 1 Remove column cap D from array column See Figure 13 2 Loosen height adjustment screws for center faceplate assembly See Figure 13 3 Slide faceplate assembly up through column channel until it is removed from column See Figure 13 Installation Instructions K3F310 Figure 13 Outside Faceplates 1 Remove hex head bolt from bottom of faceplate assembly See Figure 14 2 Slide out removable plate from bottom of faceplate assembly See Figure 14 Figure 14 3 Remove faceplate assembly from array arm See Figure 14 To Reattach Outside Faceplate Assembly NOTE Faceplate assemblies may be reattached on the fixed part of the arm See Figure 15 4 Place faceplate assembly on array arm at desired mounting position See Figure 15 5 Slide removable plate back into slot at bottom of faceplate assembly See Figure 15 6 Reinstall hex head bolt removed in Step 1 to secure faceplate assembly to array arm See Figure 15 removable plate Or Figure 15 Lateral Shift On Fixed Arm NOTE The procedure below applies when the outside faceplates have been attached to the fixed arm If outside faceplates are still attached to extension a
9. of factory warranty It is the installer s responsibility to make sure all components are properly assembled and installed using the instructions provided WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of all components located on the K3F310 up to and including the display does not exceed 15 105 6 8 kg per display WARNING Use this mounting system only for its intended use as described in these instructions Do not use attachments not recommended by the manufacturer WARNING Never operate this mounting system if it is damaged Return the mounting system to a service center for examination and repair WARNING Do not use this product outdoors SAVE THESE INSTRUCTIONS MIN DISTANCE BETWEEN MONITORS MAX DISTANCE BETWEEN MONITORS 55 93 1420 6 WIDTH 0 31 COMPATIBLE L 5 22 68 5 576 0 THIC KNESS 15 MAX ANGLE 1 21 18 54 30 6 470 9 MAX MONITOR CENTER HEIGHT FROM SURFACE 21 12 536 4 Installation Instructions K3F310 LEGEND Tighten Fastener Apretar elemento de fijaci n Befestigungsteil festziehen Apertar fixador Serrare il fissaggio Bevestiging vastdraaien Serrez les fixations Pencil Mark Marcar con lap
10. rms use the extension arms for lateral shift 1 Loosen knob on top of outside faceplate assembly until faceplate can slide freely along array arm See Figure 16 2 Adjust lateral position as desired See Figure 16 Tighten knob to secure lateral position See Figure 16 Figure 16 10 Installation Instructions Pitch Roll Yaw Adjustment Outside Faceplates 1 2 3 Loosen knob on top of faceplate assembly See Figure 17 Adjust pitch roll and or yaw as desired See Figure 17 Tighten knob to secure desired faceplate position See Figure 17 Figure 17 Center Faceplate Pitch 1 Loosen knob on side of center faceplate assembly See Figure 18 Adjust pitch as desired See Figure 18 Tighten knob to secure desired pitch position See Figure 10 Figure 18 Roll LE 2 3 Loosen screws holding display to faceplate slightly Adjust roll position as the mounting holes on faceplate allow Tighten screws to lock roll position Cable Management 1 Route cables from display through cable management covers B as desired See Figure 19 Install cable management covers B onto array A See Figure 19 Figure 19 Installation Instructions K3F310 11 10 Inst
11. wo mounting holes on faceplate selected spacers L or M into the ower mounting holes on the display See Figure 8 Figure 9 10 Installation Instructions 2 Whenarms are at desired pivot position lock pivot position by tightening pivot adjustment screws using 5 16 hex key N See Figure 10 Figure 1 Height Adjustment NOTE Height adjustment for center display should be set prior to installing display Due to the location of the height adjustment screws for the center display the center display will need to be removed in order to adjust the height See Figure 11 1 Loosen height adjustment screws for specific display that will be adjusted See Figure 11 2 Adjust arm or display to desired height See Figure 11 3 Tighten height adjustment screws to lock display s position See Figure 11 Ny A KL 6 Figure 11 Arm Extension NOTE For smaller displays or if converting to a 2x1 array faceplate assemblies may be removed and reattached to fixed part of the arm See Faceplate Assembly Section Outside Faceplates for details 1 arm extension adjustment knob counter clockwise on arm to be adjusted See Figure 12 2 Adjust arm extension as desired See Figure 12 Turn arm extension adjustment knob clockwise o
Download Pdf Manuals
Related Search