Wilson Electronics AG Pro 70
Contents
1. IC 4726A 271265 FCC ID PWO271265 Model Number Antenna connectors Antenna impedance Dimensions Weight Frequency Passband Gain nominal 220 dB Bandwidth nominal 800 MHz 45 MHz 1900 MHz 88 MHz Power Output 800 MHz 1900 MHz Power output for single cell phone uplink 30 8 dBm 30 5 dBm Power output for single received channel downlink 26 0 dBm 25 2 dBm 3Power output for multiple transmitted channels uplink Maximum Power The maximum ipower is reduced Number of channels 800 MHz 1900 MHz by the number of channels 2 24 0 dBm 21 3 dBm 3 20 5 dBm 17 8 dBm 4 18 0 dBm 15 3 dBm 5 16 0 dBm 13 3 dBm 6 14 5 dBm 11 8 dBm 800 MHz 1900 MHz AG Pro 75 amp AG Pro Installer Specifications N Female 50 ohms 70 dB Typical 75 dB Maximum 4Power output for multiple received channels downlink The maximum power is reduced by the number of channels Noise Figure typical downlink uplink Isolation Power Requirements Notes Number of channels 2 3 4 5 6 1 Nominal gain is the maximum gain at any frequency in the passband 2 Nominal bandwidth is the difference between two frequencies that are adjacent to the passband where the amplification is 20 dB lower than the passband amplification One of the frequencies is lower than the passband and the other is higher 3 The Manufacturer s rated output power of this equipment is for single carrier operation For situations when multiple carrie2. sold separately Install the Lightning Surge Protector LSP close to the Signal Booster Attach the cable from the Outside Antenna to the surge protector using a short length of low loss cable attach one end to the LSP and the other to the Outside Antenna connector on the Signal Booster Ensure the LSP is properly grounded ground wire not included For AG Pro 70 use part 859988 75 Ohm Lightning Surge Protector Visit www WilsonElectronics com or call 800 204 4104 to purchase To Outside Antenna Lightning Surge Protector sold separately lt q Ground Wire not included To Inside Antenna Surge Protector Power Strip recommended for all AC power supplies Selecting a Direction for the Outside Antenna Select a location on the roof of the building to install the Outside Antenna Use a cell phone in test mode to find the strongest signal from the cell tower see below for more information To get the strongest signal possible it is very important to set up your Outside Antenna properly The Inside and the Outside Antenna must be mounted in such a way that they are able to pick up the best possible cell signal on the outside of the building and provide the best possible signal on the inside of the building Mount the Outside Antenna as high as possible facing the cell tower in an area with the best possible signal coverage Note Never point the front of a Directional Ant
3. su Adjustable Gain Signal Boosters AG Pro 75 AG Pro 70 AG Pro Installer AG SOHO 65 AG SOHO 60 SOHO Small Office Home Office In Building Wireless 800 1900 MHz Smart Technology I Contents Antenna Options amp Accessories 0 0 0 0 ee ee 1 Quick Install Overview weed vai dawd Ce wed wees ed dee w ea 2 Installation Diagram 1 0 eee 3 Before Getting Started nanana aana ee 4 Installing the Outside Antenna 0 0 0000 eee eee 5 Finding the Strongest Signal 0 00 eee 6 Installing the Inside Antenna 0 0 0 0 eee 8 Installing a Wilson Electronics Signal Booster 9 Powering up a Wilson Electronics Signal Booster 9 Understanding the Signal Booster Lights 10 Warnings and Recommendations 13 Guarantee amp Warranty 000 eee 14 Specifications 0 0 2 ee Back Cover Appearance of device and accessories may vary Note This manual contains important safety and operating information Please read and follow the instructions in this manual Failure to do so could be hazardous and result in damage to your Signal Booster Q Wilson Electronics Inc Installation Instructions for the Following Wilson Electronics Signal Boosters AG Pro 75 AG Pro 70 AG Pro Installer amp AG SOHO 65 AG SOHO 60 In Building Wireless 800 1900 MHz Smart Technolo
4. need to turn the gain to maximum and then turn the Outside Antenna away from the cell tower until the light turns to blinking green If the Signal Booster will not respond turn the gain down 5 dB and move the Outside Antenna Continue to adjust the gain and the antenna position until the light turns blinking green Contact Wilson Electronics Technical Support Team for assistance 866 294 1660 3 SOLID RED A A red light indicates that the booster has shut down to prevent an oscillation most likely caused by the Inside and Outside Antennas being physically too close to each other Without this patented protection oscillations could be transmitted to the cell tower blocking calls to and from the cell tower Oscillation occurs just like in an audio system when you put a microphone next to a speaker and get a big squeal When the Inside Antenna is too close to the Outside Antenna the same type of oscillation occurs If the booster has a red light the following procedure needs to be done for each affected band B Either there is a problem with the Inside and Outside Antennas being too close together or there is a loose or bad cable or possibly a defective booster First check the booster by unplugging the power cord then removing the coax cables from the two connectors of the booster Adjust the Downlink DL Gain to minimum and plug the booster back in You should now have a green light if not call Wilson Electronics Technical Support Nex
5. Antenna 301129 B 50 Ohm Lightning Surge Protector N Connector 859902 3 Wide Band Directional Antenna 700 MHz C 75 Ohm Lightning Surge Protector F Connector 859988 2700 MHz 304411 Splitter options on page 8 3 A B H TTT k CT Le E s E I oer Appearance of device and accessories may vary To purchase call Wilson Electronics Sales Department at 800 204 4104 Contact Wilson Electronics Technical Support Team with any questions at 866 294 1660 or email tech wilsonelectronics com Mon Fri Hours 7 am to 6 pm MST Quick Install Overview See Installation Diagram on page 3 Contact Wilson Electronics Technical Support Team with any questions at 866 294 1660 1 Select a location to install the Signal Booster that is away from excessive heat direct sunlight moisture and has proper ventilation Do not place the Signal Booster in an air tight enclosure Select a location on the roof of the building to install the Outside Antenna Use a cell phone in test mode to find the strongest signal from the cell tower See page 6 Visit www WilsonElectronics com to find test mode function for your particular cell phone Run the Outside Antenna cable to the Signal Booster and attach it to the connector labeled Outside Antenna on the Signal Booster Run the Inside Antenna cable to the Signal Booster and attach it to the connector labeled Inside Antenna on the Signal Booster For more information on running cab
6. ble up into the fascia of the attic overhang In this circumstance the cable will be accessible in the attic for further routing Installing the Inside Antenna Instructions are for optional Panel Antenna Select a location for the Inside Antenna preferably in the center of where the signal needs to be amplified A minimum separation distance of 20 vertical feet is necessary for operation If the inside coverage is not sufficient you may need as much as 75 feet of horizontal separation See installation diagram on pages 3 amp 4 Inside Antenna Ceiling Ceilin gt Drywall Rafters In some cases multiple Inside Antennas may be required for instance if you have multiple rooms with poor signal A signal may be split by using a splitter sold separately If using more than one Inside Antenna a separation up to 75 horizontal feet may be necessary between Inside Antennas See configuration on pages 3 amp 4 A Warning An Inside Antenna must have a separation distance from all persons that is at least 15 inches for the Panel Antenna Optional Wide Band Inside 5 7 l Antenna sold Splitter Options sold separately separately j 2 way 3 way 4 way 859957 859980 859981 Contact Wilson Electronics Technical Support Team with any questions at 866 294 1660 or email tech wilsonelectronics com Mon Fri Hours 7 am to 6 pm MST Installing a Wilson Electronics Signal Booster Select a location to in
7. e All gain controls should be set to maximum If you have green lights the installation is complete If one or more lights are blinking orange the Signal Booster is experiencing receiver overload Reduce the uplink UL gain control without reducing the downlink DL gain to eliminate the overload This configuration will eliminate cell tower interference overload without reducing coverage in the building Contact Wilson Electronics Technical Support Team with any questions at 866 294 1660 or email tech wilsonelectronics com Mon Fri Hours 7 am to 6 pm MST Warnings and Recommendations A Warning The Directional Antenna must always be located so the back or side points to the Inside Antenna Never point the front of the Outside Antenna toward the Inside Antenna this is to prevent oscillation A Warning Connecting the Signal Booster directly to the cell phone with use of an adapter will damage the cell phone A Warning Use only the power supply provided Use of a non Wilson Electronics product may damage your equipment As Warning RF Safety FCC regulations require that any fixed Outside Antenna used with this Signal Booster may not have gain less cable loss that exceeds 15 dBi and must be located at least 30 inches from all people Inside Antennas must not exceed 7 dBi gain less cable loss in the 800 MHz band or 10 dBi gain less cable loss in the 1900 MHz band and must be located at least 15 inches fro
8. enna toward the Inside Antenna See Figures 1 amp 2 on page 10 Finding the Strongest Signal When installing your Signal Booster s Outside Antenna aiming it towards the best signal source from you service provider is important The best way of getting the strongest signal is to have one person on the roof to rotate the Outside Antenna which is connected to the Signal Booster Turning the Outside Antenna about 45 degrees at a time while the second person is watching the signal strength on the phone inside the building This allows Contact Wilson Electronics Technical Support Team with any questions at 866 294 1660 or email tech wilsonelectronics com Mon Fri Hours 7 am to 6 pm MST you to read the signal strength from the cell tower It is preferable to have the phone in the test mode so the actual signal strength can be read as bars are not the most accurate Go to www WilsonElectronics com for help in finding the test mode for your phone Always make sure the person inside the building gives the signal time to arrive and register on the phone between 10 30 seconds for phone to reset to the signal reading Cell Signal Outside h Wide Band Antenna Signal Strength Graph A EXCELLENT NO SIGNAL 60dB 70dB 80dB 90dB 100dB 110dB Signal readings usually appear as a negative number for example 86 The closer you get to zero the stronger the signal See graph above Mounting Tips for Running O
9. gy I Signal Boosters Model 271265 FCC ID PWO271265 IC 4726A 271265 The term IC before the radio certification number only signifies that Industry Canada technical specifications were met How it Works Wilson Electronics Signal Boosters are bi directional devices that deliver service levels consistent with what would be expected in areas of high cell network coverage They amplify a weak or shadowed signal in mobile marine and in building applications When using a Wilson Electronics Signal Booster in conjunction with Wilson Electronics antennas the Outside Antenna will collect the cell tower signal and send it through the cable to the Signal Booster The signal is then amplified and re transmitted through the Inside Antenna into the room Cell phones and cellular data cards in that area then communicate with the improved signal When a cell phone or cellular device transmits the signal is received by the Inside Antenna amplified by the Signal Booster and transmitted back to the cell tower through the Outside Antenna Inside this Package Note Kits may contain different accessories i AC DC Signal N Female FME F le Adapt Power Booster Sold with the Supply The AG Pro Installer AG SOHO 60 has a different knob configuration MT a Outdoor Antenna Options Indoor Antenna Options amp Accessories 1 1900 MHz Yagi PCS Antenna 301124 A Wide Band Panel Antenna 700 2700MHz 301155 2 800 MHz Yagi Cellular
10. he 1900 MHz band For the first 15 minutes that the Signal Booster is plugged in itis fora test and alignment period During this time both lights will do one of the following 4 things Note If after the initial 15 minutes you are not done with the installation the Signal Booster can be reset and enter installation mode again by disconnecting and reconnecting the power supply from the Signal Booster 1 BLINKING GREEN If the Signal Booster is blinking green the Signal Booster is operating properly If you are happy with the coverage area in your building then you are done Blinking will stop after the 15 minute installation period 2 BLINKING ORANGE Note For AG Pro Installer see additional instructions on page 12 If either of the two lights on the Signal Booster are blinking orange the Signal Booster is experiencing receiver overload The Signal Contact Wilson Electronics Technical Support Team with any questions at 866 294 1660 or email tech wilsonelectronics com Mon Fri Hours 7 am to 6 pm MST Booster has protection shut off circuits to prevent the disruption of cell towers If one or both lights are blinking orange this indicates that the Signal Booster has shut down due to close proximity to a cell tower First turn down the gain control on the band that is blinking until you get a blinking green light The Signal Booster is now working with reduced gain If the gain is not adequate for good coverage you will
11. hysical or electronic properties Failure to use a surge protected AC Power Strip with at least a 1000 Joule rating will void your warranty RMA numbers may be obtained by contacting Technical Support at 866 294 1660 This device complies with Part 15 of FCC rules The transaction is subject to two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Changes or modifications not expressly approved by Wilson Electronics could void the authority to operate this equipment Disclaimer The information provided by Wilson Electronics Inc is believed to be complete and accurate However no responsibility is assumed by Wilson Electronics Inc for any business or personal losses arising from its use or for any infringements of patents or other rights of third parties that may result from its use Copyright 2012 Wilson Electronics Inc All rights reserved One or more of the following U S Patent numbers may apply to the Signal Booster in this product D596 614 D596 615 D563 381 7 729 669 7 486 929 7 729 656 7 409 186 7 783 318 7 684 838 12 714 994 Contact Wilson Electronics Technical Support Team with any questions at 866 294 1660 or email tech wilsonelectronics com Mon Fri Hours 7 am to 6 pm MST AG Pro 75 AG Pro 70 AG Pro Installer AG SOHO 60 amp AG SOHO 65 Specifications
12. ing multiple inside antennas Surge Protecto 2 Power ee Contact Wilson Electronics Technical Support Team with any questions at 866 294 1660 I or email tech wilsonelectronics com Mon Fri Hours 7 am to 6 pm MST a Reasons for Weak Cellular Signals Anyone who uses a cell phone or cellular data card knows the frustration of not being able to connect to or maintain a strong cellular signal When this occurs it is generally due to one of two reasons 1 Location of the Nearest Cell Tower Cell towers are situated to provide broad coverage however there are many areas in which signal strength may be reduced by topographic features or by local government restrictions on the height or placement of the towers themselves Rural areas generally have fewer cell towers than urban regions 2 Natural and Man Made Obstructions Signal strength can also be negatively affected by trees hills buildings weather and other obstructions You may be relatively close to a cell tower but still unable to make a call This often occurs in homes offices and other buildings in which stucco concrete or metal walls may block the signal The Signal Booster works with two antennas The Inside Antenna communicates with your cell phone and the Outside Antenna communicates with the cell tower The Outside Antenna receives the cell tower signal and sends it through the cable to the Signal Booster where it is amplified and re tra
13. le see page 7 Lightning Surge Protection is recommended for all in building installations See page 6 Select a location for the Inside Antenna preferably in the center of where the signal needs to be amplified A minimum separation distance of 20 vertical within the null zone or 50 horizontal feet is necessary for proper operation If the inside coverage is not sufficient you may need to increase the separation distance even further See installation diagram on pages 3 amp 4 Before powering up the Signal Booster verify that both the Outside Antenna and the Inside Antenna are connected and check that all connections are tight Note Be careful when plugging the connectors in so as not to bend the center pins on the connectors see page 9 The Signal Booster has been packaged with the gain control knobs adjusted to the highest gain position If one or both of the lights are not green please refer to pages 10 12 For AG Pro Installer see page 12 Warning Connecting the Signal Booster directly to a cell phone with use of an adapter will damage the cell phone and or the Signal Booster IMPORTANT NOTICE e Itis very important to power your Signal Booster using a surge protected AC Power Strip with at least a 1000 Joule rating Z5 B Failure to do this will void your warranty in the event of a power surge or lightning strike Contact Wilson Electronics Technical Support Team with any que
14. m all people As Warning Verify that both the Outside Antenna and the Inside Antenna are connected to the Signal Booster before powering up the Signal Booster Recommendation Lightning Surge Protection is recommended for all in building installations About Wilson Electronics Wilson Electronics Inc has been a leader in the wireless communications industry for over 40 years The company designs and manufactures Signal Boosters antennas and related components that significantly improve cellular phone signal reception and transmission in a wide variety of applications both mobile marine RV vehicles and in building home office M2M With extensive experience in antenna and Signal Booster research and design the company s engineering team uses a state of the art testing laboratory including an anechoic chamber and network analyzers to fine tune antenna designs and performance For its Signal Boosters Wilson Electronics uses a double electrically insulated RF enclosure and cell tower simulators for compliance testing Wilson Electronics Signal Boosters feature patented Smart Technology I that enables them to automatically adjust their power based on cell tower requirements By detecting and preventing oscillation feedback signal overload and interference with other users these Smart Technology I Signal Boosters improve network cell phone areas without compromising carrier systems All products are engineered and asse
15. mbled in the company s 55 000 square foot headquarters in St George Utah Wilson Electronics has product dealers in all 50 States as well as in countries around the world Contact Wilson Electronics Technical Support Team with any questions at 866 294 1660 or email tech wilsonelectronics com Mon Fri Hours 7 am to 6 pm MST 30 Day Money Back Guarantee All Wilson Electronics products are protected by Wilson Electronics 30 day money back guarantee If for any reason the performance of any product is not acceptable simply return the product directly to the reseller with a dated proof of purchase 1 Year Warranty Wilson Electronics Signal Boosters are warranted for one 1 year against defects in workmanship and or materials Warranty cases may be resolved by returning the product directly to the reseller with a dated proof of purchase Signal Boosters may also be returned directly to the manufacturer at the consumer s expense with a dated proof of purchase and a Returned Material Authorization RMA number supplied by Wilson Electronics Wilson Electronics shall at its option either repair or replace the product Wilson Electronics will pay for delivery of the repaired or replaced product back to the original consumer if located within the continental U S This warranty does not apply to any Signal Booster determined by Wilson Electronics to have been subjected to misuse abuse neglect or mishandling that alters or damages p
16. nsmitted much stronger through the Inside Antenna into the room When the Inside Antenna picks up a signal from your cellular device the Signal Booster amplifies that signal and transmits it through the cable to the Outside Antenna and back to the cell tower Note The Signal Booster will only operate if there is an adequate signal to amplify Outside Antenna Installation part 304411 shown Antenna Drip hole on bottom The antenna should be mounted as shown in the illustration above The mounting bracket included with antenna is adjustable and will accommodate pipe diameters from 1 25 to 2 pipe sold separately part 901117 Mount the antenna so that there is at least 3 feet of clearance in all directions around it Position the antenna so that it has an unobstructed line of sight to the cell tower s strongest signal Make sure the antenna is not pointing across your own roof or at the Inside Antenna as this will cause the oscillation protection circuitry to shut down the Signal Booster see page 10 Cell Tower Contact Wilson Electronics Technical Support Team with any questions at 866 294 1660 or email tech wilsonelectronics com Mon Fri Hours 7 am to 6 pm MST A Warning Lightning protection is recommended for all installations sold separately part 859902 or 859988 Take extreme care to ensure that neither you nor the antenna comes near any electric power lines Installing Lightning Protection
17. r signals are present the rating would have to be reduced by 3 5 dB especially where the output signal is re radiated and can cause interference to adjacent band users This power AG Pro 70 Specifications AG SOHO 65 Specifications 271265 F Female N Female 75 ohms 50 ohms 5 7 x 4 2 x 1 5 inch 14 0 x 10 8 x 3 9 cm 1 27 Ibs 0 544 kg 824 894 MHz 1850 1990 MHz 65 dB Typical 60 dB Typical 70 dB Maximum 65 dB Maximum 800 MHz 24 8 dBm 21 3 dBm 18 8 dBm 16 8 dBm 15 3 dBm Maximum Power 3 5 dB nominal 6 dB nominal gt 90 dB 110 240 V AC 50 60 Hz 8 W reduction is to be by means of input power or gain reduction and not by an attenuator at the output of the device 4 The maximum power for 2 or more simultaneous signals will be reduced by 6 dB every time the number of signals is doubled Wilson Electronics Inc 3301 East Deseret Drive St George UT 84790 For additional Technical Support visit www WilsonElectronics com or email at tech wilsonelectronics com Phone 866 294 1660 Local 435 673 5021 www twitter com WilsonCellular 1900 MHz 23 7 dBm 20 2 dBm 17 7 dBm 15 7 dBm 14 2 dBm AG SOHO 60 Specifications FME Male 50 ohms 55 dB Typical 60 dB Typical Fax 435 656 2432 www facebook com WilsonCellular AIG 110769_Rev09_03 16 12
18. stall the Signal Booster that is away from excessive heat direct sunlight moisture and that has proper ventilation Do not place the Signal Booster in an air tight enclosure Recommended installation locations for in building Signal Boosters are near a power outlet and in a closet or on a shelf Note t is important to have adequate air ventilation Maintain at least 6 inches of clearance from surrounding objects Be careful when plugging the connector in so as not to damage the center pins on the connectors Run the Outside Antenna cable to the Signal Booster and attach it to the connector labeled Outside Antenna on the Signal Booster Run the Inside Antenna cable to the Signal Booster and attach it to the connector labeled Inside Antenna on the Signal Booster Note For distances of 20 feet or more use Wilson low loss cable Powering up a Wilson Electronics Signal Booster 1 Never point the front of a Directional Outside Antenna toward the Inside Antenna See Figures 1 amp 2 on page 10 2 Ensure that both the Outside Antenna cable and the Inside Antenna cable are connected to the Signal Booster and the connections are tight before powering up the Signal Booster OO Plug the power supply into the Signal Booster input marked 6V DC carefully to avoid damaging the center pin and then into a wall outlet Note Wilson Electronics recommends that all AC power supplies for home electronics be plugged into a S
19. stions at 866 294 1660 or email tech wilsonelectronics com Mon Fri Hours 7 am to 6 pm MST Installation Diagram seme T Outside Antenna Inside Antenna Preferred Method Place the Inside Antenna in the ceiling facing down for the best coverage Note The Inside Antenna may be mounted on the wall directly under the Outside Antenna in the null zone if 20 feet of vertical separation can be maintained Zz Optional Null Zone The area under the second Outside Antenna where the gt antenna for Outside Antenna radiates the additional least coverage Note A Lightning Surge Protector is recommended for all building installations sold separately Make sure the protector is installed in line between the Outside Antenna and the Signal Booster ypical Installation Contact Wilson Electronics Technical Support Team with any questions at 866 294 1660 or email tech wilsonelectronics com Mon Fri Hours 7 am to 6 pm MST Before Getting Started This guide will help you properly install your Wilson Electronics Signal Booster It is important to read through all of the installation steps for your particular application prior to installing any equipment Read through the instructions visualize where all the equipment will need to be installed and do a soft installation before mounting any equipment Contact Wilson Electronics Technical Support with any questions at 866 294 1660 Splitter if us
20. t unplug the booster reconnect the coax cables to the booster and tighten all connections and plug the booster back in C Increase the DL Gain until you get a red light for example it may be at 50 dB for the red light This indicates that an oscillation occurs at gains 50 dB and higher Separating the antennas is very important to get the necessary gain for the system to give maximum coverage and a green light Lowering gain decreases your coverage area The Outside Antenna if directional needs to be pointed at the cell tower with its back to the Inside Antenna The Inside Antenna needs to have its back facing the back of the Outside Antenna Without proper orientation of the antennas you will not be able to get maximum gain from the booster Contact Wilson Electronics Technical Support Team with any questions at 866 294 1660 or email tech wilsonelectronics com Mon Fri Hours 7 am to 6 pm MST Note Ifthe antennas cannot be sufficiently separated the booster will have to operate with reduced performance by decreasing the Downlink Gain until a green light is obtained 4 SOLID GREEN The indicator lights on the Signal Booster will be a solid green after the first 15 minute installation period if the unit is powered up and working properly Additional Instructions for the AG Pro Installer with separate uplink and downlink gain controls This Signal Booster is supplied with separate uplink and downlink gain controls Not
21. urge Protector Power Strip 4 If the Signal Booster does not have a green light s please see pages 10 12 See page 12 for AG Pro Installer O1 If you know that only one frequency band 800 or 1900 is available in your coverage area or going to be used reduce the gain control on the frequency band that is NOT in use to the lowest setting This will reduce the power consumption of the Signal Booster 6 Using multiple Signal Boosters in one installation could cause interference to the cell tower except for the In Line Signal Booster 7 Contact Wilson Electronics Technical Support Team with any questions at 866 294 1660 or email tech wilsonelectronics com Technical Support hours are Mon Fri 7am to 6 pm MST Contact Wilson Electronics Technical Support Team with any questions at 866 294 1660 or email tech wilsonelectronics com Mon Fri Hours 7 am to 6 pm MST Figure 1 Figure 2 CORRECT INSTALLATION INCORRECT INSTALLATION Point antennas away from each other Never point antennas toward each other Li k B Outdoor f Antenna DN Outdo Inside Pa Antenna Antenna e Signal Booster Signal Booster Understanding the Signal Booster Lights and Troubleshooting During installation mode the Signal Booster is resetting itself very quickly to aid the installer The Signal Booster is equipped with two indicator lights one for the 800 MHz band and the other for t
22. utside Antenna Cable If you are mounting the Outside Antenna on the roof of your building we have found that it is easiest to run your cable underneath the down side of your roof s flashing If you have satellite TV service installed you may be able to follow the same route as the satellite TV cables that are already running from outside of your building to the inside After routing the cable we recommend sealing any areas where the cable passes into the building with cable bushings silicone or other waterproof sealant to keep your installation from leaking If you are mounting the Outside Antenna to the outside wall of your home or building the simplest way is to run the cable on the outside of the wall and attach it to the exterior of your home or office Then drill a hole through the wall where you want the cable to appear on the inside of the building Before drilling make sure that there are no electrical outlets sewer or water pipes or electrical wiring in the wall that you are about to drill through as this could potentially harm you or damage the building Contact Wilson Electronics Technical Support Team with any questions at 866 294 1660 or email tech wilsonelectronics com Mon Fri Hours 7 am to 6 pm MST After drilling the required hole run the cable through and seal it with cable bushings silicone or other waterproof sealant to enclose the hole that you have created In some instances it may be possible to run the ca
Download Pdf Manuals
Related Search