Zalman CNPS9900DF
Contents
1. keys on Insert the Nuts to the Backplate according to the socket type and secure them with Side Caps l Caution S Take note of the orientation of the Nuts and the Side Caps ZALMAN COM Peel off the Loading Block cover and attach it to the Backplate with the sticky side facing the center of the Backplate Loading Block Peel off one side of the Double sided Tape and attach it with the sticky side facing the Loading block Then peel off the top cover Double sided Tape Please note that the sticky side of the Loading Block serves to attach the Loading Block to the backplate Dismantle the CPU cooler retention bracket on the motherboard by unscrewing the four bolts located at each corner method may vary consult the motherboard manual for details Be sure to keep the retention bracket so the stock CPU cooler can be used as a backup Attach the Backplate assembly to the back side of the motherboard by aligning the Nuts to the motherboard mounting holes If you were unsuccessful at first attempt you may continue with the installation without the Double sided Tape as it is not a necessary component Apply thermal grease just enough to thinly cover the CPU surface Then insert four Silver Bolts B through the AMD Clip holes and using the 32. Socket LGA 1366 Socket LGA 2011 Socket AMD LGA1156 1155 775 ZALMAN COM 2 Intel Socket LGA 1366 1156 1155 775 Installation Insert the Nuts to the Backplate according to the socket type and secure them with Side Caps Socket 775 Socket 1156 1155 Socket 1366 A Caution S Take note of the orientation of the Nuts and the Side Caps Ca Ss Socket LGA 1366 1156 1155 Installation Peel off one side of the Double sided Tape and attach it to the center of the Backplate with the sticky side facing down Then peel off the top cover X Socket LGA 1366 1156 1155 Installation does not require the Loading Block ZALMAN COM Socket LGA 775 Installation Peel off the Loading Block cover and attach it to the Backplate with the sticky side facing the center of the Backplate Peel off one side of the Double sided Tape and attach it with the sticky side facing the Loading block Then peel off the top cover Double sided Tape A Caution Please note that the sticky side of the Loading Block serves to attach the Loading Block to the backplate cT im i l 0 a a r ZALMAN COM Attach the Backplate assembly to the back side of the motherboard by aligning the Nuts to the motherboard mounting holes If you were unsuccessful at first attempt you may continue with the inst
3. problems with electrical power accident neglect alteration repair improper installation or improper testing D 2 Specifications Ee ee 140 L x 110 W x 154 H m RPM Center 140mm 900 1 400rpm 10 4pin Fan Noise Level 19 27dBA 10 Bearing Type Long Life Bearing ZM STG2 Temperature Range 40 C 150 C 40 F 302 F O 3 Components 1 Common Components Manual Backplate User s Manual Kee Cz Thermal Grease H ZM STG2 Side Caps Allen Wrench 3 32 SIS 5 SE Pee J jee Gold Bolts Silver Bolts A 4mm Silver Bolts B 3mm Socket LGA 1366 Socket LGA 2011 Socket AMD LGA 1156 1155 775 m i EE sea 4404 CO Y Connector Cable Nuts Loading Block Double sided Tape 3 AMD Components Socket FM2 FM1 AM3 AM3 AM2 AM2 2 Intel Components Socket LGA 2011 1366 1156 1155 775 Intel Clip AMD Clip ZALMAN COM J 4 Installation Requirements 1 Space Requirements The installation requires unobstructed space of 110mm width x 140mm length x 154mm height with the CPU as the central reference point Before installation please check if memory modules or motherboard heatsinks will not have any clearance issues with the CPU cooler 2 Air Guide Removal Air guides on enclosures must be removed before the cooler s installation for they protrude into the cooler s required space 3 Protective Brace Removal Please u
4. 23 Allen Wrench fasten the Bolts incrementally while alternating between them Allen Wrench A Caution Please make sure to use the Bolts with correct color and thread length as they can appear quite similar Gold Bolts Sliver Bolts A 4mm Sliver Bolts B 3mm Socket LGA 1366 Socket LGA 2011 Socket AMD LGA 1156 1155 775 S Connect the Y Connector Cable to the 4Pin 140mm Center FAN 3pin 120mm Front FAN Connect the Y Connector Cable to the mother board 4 XQ B60 A Caution amp make sure that PWM Control Mode is activated in the motherboard s BIOS settings Beware of fan wire interuption ZALMAN COM
5. CNPS9900 DF Intel Socket LGA 2011 1366 1156 1155 775 CPUs AMD Socket FM2 FM1 AM3 AM3 AM2 AM2 CPU amp APUs To ensure safe and easy installation please read the following precautions www ZALMAN com H 1 Precautions 1 2 3 4 5 6 7 8 9 10 Avoid inserting objects or hands into the fan while it is in operation to prevent product damage and injuries Do not ingest the Thermal Grease and avoid its contact with skin and eyes If contact is made with skin wash off with water If ingested or irritation persists seek medical attention To prevent possible injuries gloves must be worn while handling this product Excessive force exerted on the fan may cause damage to the fan and or system Use and keep product away from the reach of children and pets Check the components list and condition of the product before installation If any problem is found contact the retailer to obtain a replacement Zalman Tech Co Ltd is not responsible for any damages due to overclocking Before transportation of the system the cooler must be removed Zalman is not responsible for any damages that occur during the transport of a system Enable PWM function in BIOS settings after installation Product design and specifications may be revised to improve quality and performance Disclaimer Zalman Tech Co Ltd is not responsible for any damages due to external causes including but not limited to improper use
6. allation without the Double sided Tape as it is not a necessary component Apply thermal grease just enough to thinly cover the CPU surface Then insert four Silver Bolts B for socket LGA 1156 1155 775 or Gold Bolts for LGA 1366 through the Intel Clip holes and using the 3 32 Allen Wrench fasten the Bolts incrementally while alternating between them Gold Bolt Socket 1366 Sliver Bolt B 3mm Socket 1156 1155 775 VAN Caution Please make sure to use the Bolts with correct color and thread length as they can appear quite similar a Gold Bolts Sliver Bolts A 4mm Sliver Bolts B 3mm Socket 1366 Socket 2011 Socket 1156 1155 775 AMD Connect the Y Connector Cable to the 4Pin 140mm Center FAN 3pin 120mm Front FAN Connect the Y Connector Cable to the mother board A Caution Please make sure that PWM Control Mode is activated in the motherboard s BIOS settings Beware of fan wire interuption ZALMAN COM J au S Fz B AMD Socket Installation 1 AMD Socket FM2 FM1 AM3 AM3 AM2 AM2 Installation Partially unscrew the four bolts located on the base of the CPU cooler Then insert the AMD Clips between the base and the heatpipe cover with the clips bent away from the heatsink Base Ly the heatpipe cover for secure Clip C installation l F N The holes in the Clip as shown ii below are matched to the
7. nclip and remove the heatsink s plastic brace before installing the cooler 4 Cooler Orientation Orient the cooler so that the thinner heatsink is facing the rear exhaust fan while the thicker heatsink is facing the front case fan see right image 5 Fan Protection Pad Removal amp Cooler Handling Remove the fan protection pad before you begin the installation process Also due to the sharp heatsink fins wearing gloves while handling the heatsink fins is strongly recommended g 5 Installation A Intel Socket Installation Go to Page 8 For AMD Sockets Partially unscrew the four bolts located on the base of the CPU cooler Then insert the Intel Clips between the base and the heatpipe cover with the clips bent away from the heatsink 1 Intel Socket 2011 Installation Base K A Intel Clip The holes in the Clip as shown below are matched to the keys on the heatpipe cover for secure Clip installation Apply thermal grease just enough to thinly cover the CPU surface Then insert four Silver Bolts type A through the outermost Intel Clip holes and using the 3 32 Allen Wrench fasten the Silver Bolts incrementally while alternating between them Sliver Bolt A 4mm j A Caution Please make sure to use the Bolts with correct color and thread length as they can appear quite similar Sliver Bolts A 4mm Sliver Bolts B 3mm
Download Pdf Manuals
Related Search