EK Water Blocks 3831109820902
Contents
1. EAN 3830046996626 5 PLACING THERMAL PADS ON MOTHERBOARD Place thermal pads you cut on PCB as shown on picture bellow PLEASE REMOVE THE PROTECTIVE FOIL FROM BOTH SIDES OF THE THERMAL PADS PRIOR TO INSTALLATION EK recommends using small drops of electrically non conductive for example Arctic Cooling MX 2 MX 4 or GELID GC Extreme thermal grease on each phase regulator that is being covered with thermal pad see picture below in order to even further improve the thermal performance of the EK FB ASUS M5E series water block Place 1 0mm thick thermal pads in larger strips over marked area and make sure all mosfet chips are covered All disclosures notices and warranty conditions are being written on EKWB web page Please check terms of use Revision 1 0 Published on November 9 2012 1 PLACING SB BLOCK ON MOTHERBOARD Place the EK FB ASUS M5E series water block with pre installed 2 1mm standoffs kit gently to the motherboard or vice versa Make sure that mounting holes are aligned Prior to fastening the screws please make sure the mounting holes on the motherboard s Temporarily remove the water block to check for uniform surface contact between circuit board are aligned with water block the block and the components Note the pattern of contact on a piece of paper Then repeat steps 3 and 4 to reattach the block applying more or less pressure to the areas where you have found it necessary Note that there is no need for2. Installation and mounting manual for EK FB ASUS MS5E water block This product is intended for installation only by expert users Please consult with a qualified technician for installation Improper installation may result in damage to your equipment EK Water Blocks assumes no liability whatsoever expressed or implied for the use of these products nor their installation The following instructions are subject to change without notice Please visit our web site at www ekwb com for updates Before installation of this product please read important notice disclosure and warranty conditions printed on the back of the box Before you start using this product please follow these basic guidelines 1 Please carefully read the manual before through before beginning with the installation process 2 Please remove your motherboard from the computer to assure safest mounting process in order to prevent any possible damages to your CPU and or motherboard s circuit board PCB 3 The EK High Flow and EK PSC type fittings require only a small amount of force to screw them firmly in place since the liquid seal is ensured by the rubber o ring gaskets 4 The use of quality market proved corrosion inhibiting coolants is always strongly recommended for any liquid cooling system STEP 1 GENERAL INFORMATION Sample photo of ASUS Maximus V Extreme motherboard za a m m Mosfets PLX PEX 8747 PCle lane splitter SsSnwixuw Jj Sau i xa CP
3. U socket Intel Z77 PCH SB c STEP 2 PREPARING YOUR MOTHERBOARD 1 REMOVING STOCK COOLER Remove all encircled screws There are 10 screws 2 CLEANING THE PCB Carefully detach the original stock cooler after removing all on the back of the motherboard that needs to be removed in order to remove the screws securing it to the board Wipe off the remains by using non abrasive cloth or factory installed MOSFET as well as NB SB heatpipe cooling solution gtip as shown on sample photo of the original thermal compound until the components Ro FS T E and circuit board are completely clean EKWB recommends the use of denatured alcohol Baie Ka i BnD De l cae a for removing TIM leftovers OLDO O O re A RL O R oe Jeo x a u seses E Aihala 3 APPLYING THERMAL COMPOUND Apply thermal compound lightly coat the 4 CUTTING THERMAL PADS Your block comes with two thermal pads which needs to Intel Z77 PCH SB as well as PLX PEX 8747 with electrically non conductive thermal be trimmed in order to fit the voltage regulation area VRM MOSFET on the grease for example Arctic Cooling MX 2 MX 4 or GELID GC Extreme EKWB motherboard s circuit board WARNING DIMENSIONS ON PICTURES BELOW ARE recommends to apply thermal grease in cross form for best performance see SCALED sample picture 100 3 GS AAN i U N X 16 Replacement thermal pads EKWB web shop Thermal PAD A 1 0mm 100x16mm
4. perfect thermal pad imprint on the inductors coils mentioned in STEP2 Use eight M2 5x4 DIN7985 and washers Tighten the screws beginning near the center of the board and continue evenly outwards Do not use excessive force when tightening the screws Re use ASUS factory stock backplate and two M2 5x8 to secure the last two mounting positions Use the enclosed screws and washers as shown in picture below Chip die thermal grease imprint M2 5x4 screw i e EN Thermal pad imprints ee ASUS factory backplate PVC washer Attach the liquid cooling tubes and connect the water block s into the cooling circuit EKWB recommends using EK PSC compression fittings with the EK FB ASUS M5E series water block You can use any opening as an inlet outlet port Plan your tubing routing in advance HBHHHBRHEHEHEHEHEHEHEHEHR HERR RE Ree ee ee 2 a5 PLEASE NOTE The largest i compatible fitting is EK PSC Fitting _ 12mm In order to use EK PSC Fitting 13mm or larger 3rd party connectors it is mandatory to use EK Extender G1 4 EAN 3831109845165 This extender is not enclosed and must be purchased separately EN REQUIRED TOOLS AND MOUNTING SCREWS E Z scissors philips screwdriver A thermal grease All disclosures notices and warranty conditions are being written on EKWB web page Please check terms of use Revision 1 0 Published on November 9 2012
Download Pdf Manuals
Related Search