Vision Snapshot
Contents
1. NG THE UNIT Before moving the unit be sure to pull out the power cord from the AC outlet and disconnect the interconnection cords with other units WARNI NG SI GNS If you detect an abnormal smell or smoke turn this product off immediately and unplug the power cord Contact your reseller or Vision PACKAGI NG Save all packing material It is essential for shipping in the event the unit ever needs repair IF ORIGINAL PACKAGING IS NOT USED TO RETURN THE UNIT TO THE SERVICE CENTRE DAMAGE IN TRANSIT WILL NOT BE COVERED BY WARRANTY 3 TC2 CTL3_manual_en FRONT AND REAR PANELS 1 1 2 3 4 5 BUTTONS 1 3 5 Learn Confirmation LED green Learn Mode LED red IR Receiver Internal IR Blaster Emitter Function Buttons 3 Hao WEA LAC AEL Ari 6 RS 232 i k i i i 1 o na J 7 PWR in 12V 0 5A 8 12V Trigger out 9 RS 485 10 IR out 10 4 TC2 CTL3_manual_en CONTROL OPTIONS IR Techconnect Control learns and replicates codes sent from a device s infrared remote control An IR emitter integrated into the front panel is adequate for small rooms For larger rooms three external wired IR emitters are included one with a 10m cable and two without cables Techconnect Minijack cables are suitable to extend these NOTE There is no theoretical cable length limit on IR cables NOTE Remote controls which co2. IC SHOCK DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE All products are designed and imported into the EU by Vision who is wholly owned by Azlan Logistics Ltd Registered in England Nr 04625566 at Lion House 4 Pioneer Business Park Clifton Moor York YO30 4GH WEEE Registration GDOO46SY DECLARATION OF ORIGIN All Vision products are made in the People s Republic of China PRC 2 TC2 CTL3_manual_en USE ONLY DOMESTIC AC OUTLETS Connecting the unit to an outlet supplying a higher voltage may create a fire hazard HANDLE THE POWER CORD WITH CARE Do not disconnect the plug from the AC outlet by pulling the cord always pull the plug itself Pulling the cord may damage it If you do not intend to use your unit for any considerable length of time unplug the unit Do not place furniture or other heavy objects on the cord and try to avoid dropping heavy objects on it Do not tie a knot in the power cord Not only could the cord be damaged but a short circuit could also be caused with a consequent fire hazard PLACE OF INSTALLATI ON Avoid installing this product under the following conditions Moist or humid places Places exposed to direct sunlight or close to heating equipment e Extremely cold locations Places subject to excessive vibration or dust Poorly ventilated places Do not expose this product to dripping or splashing DO NOT PLACE OBJECTS FILLED WITH LIQUIDS ON OR NEAR THIS PRODUCT MOVI
3. NECT CABLES Connect appropriate cables and fit the module into the surround In very simple installations it may not be necessary to connect any cables 6 TC2 CTL3_manual_en SIMPLE MODE PROGRAMMING Appropriate for controlling one IR device only e g projector 1 PUT DEVICE INTO LEARN MODE Press and hold buttons 3 and 4 middle buttons The learn LED on the front panel will turn red and stay on PRESS BUTTON TO ASSIGN CODE TO Press function button on the front panel which the incoming code will be assigned to One code can be assigned to each button TEACH CODE Point remote control at the front panel of Control module Press and hold the button on the remote until the green confirmation LED flashes If red LED flashes it has failed to learn the code Try again NOTE Remote control should be 100mm from IR receiver and not held at an angle Shield from ambient light REPEAT The device will revert back to normal mode once it has learnt a code Repeat steps above to program other buttons BUTTON 2 Automatically sends code twice Suitable for projector off This can be disabled with the computer software BUTTON 5 6 Sends codes repeatedly when held down Suitable for volume control This can be disabled with the computer software 7 TC2 CTL3_manual_en ADVANCED MODE PROGRAMMING NOTE Device must use mains power for these advanced functions Use when you need to Program multiple codes to each button Use RS 232
4. VISION installation innovation TECHCONNECT CONTROL OWNERS MANUAL www visionaudiovisual com techconnect tc2 ctl3 1 TC2 CTL3 manual en DECLARATION OF CONFORMITY Where applicable Vision products are certified and comply with all known local regulations to a CB Certification standard Vision commits to ensure all products are fully compliant with all applicable certification standards for sale in the EU and other participating countries The product described in this owner manual is in compliance with RoHS EU directive 2002 95 EC and WEEE EU directive 2002 96 EC standards This product should be returned to the place of purchase at the end of its useful life for recycling WARNINGS RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL user to the presence of uninsulated dangerous voltage within the product s enclosure that may be h The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the of sufficient magnitude to constitute a risk of electric shock to persons important operating and maintenance servicing instructions in the literature accompanying the 1 The exclamation point within an equilateral triangle is intended to alert the user to the presence of appliance WARNING TO REDUCE THE RISK OF FIRE OR ELECTR
5. eath or injury EU85 374 EEC This warranty protects you against the following e Failure of any components including the power supply Damage when the product is first removed from its packaging if reported within 24 hours of purchase If you find you do have a problem with this product you should contact the AV reseller you purchased this product from The original purchaser is responsible for shipment of the product to the manufacturer s appointed service centre for repair We will endeavour to return repaired units within 5 working days however this may not always be possible in which case it will be returned as soon as practicably possible In line with our WEEE commitments the manufacturer endeavours to replace the faulty parts of the product rather than replacing the whole unit This warranty does not protect this product against faults caused by abuse misuse incorrect installation unstable or faulty power input which might be caused by ignoring the guidelines set out in this manual LEGAL DISCLAIMER Because we are committed to improving our products the details above may change without prior warning This User Manual is published without warranty and any improvements or changes to the User Manual necessitated by typographical errors inaccuracies of current information or improvements to programs and or equipment may be made at any 11 TC2 CTL3_manual_en time and without notice Such changes will be incorporated into ne
6. ling function do this once all of the codes have been learnt IMPORTANT The software contains a pre set library of RS 232 codes When you add new codes and sync and software those new codes become available to all users when they sync and can be edited If an extension keypad is used all code will be saved on the master device The slave device is connected to the master via the RS485 terminal TROUBLESHOOTING If your system is not operating properly please refer to the following information If the problem persists disconnect from power and contact your AV reseller immediately Problem No LED when buttons pressed Module fails to learn the code Correction If powered by batteries make sure switch under batteries set to BATT or PWR as appropriate Replace batteries Voltage must be higher than 2 8V Check mains power connection if using If using mains power remove batteries Make sure codes have been learnt Make sure the original remote is 50mm away from the IR receiver on the top front of the module and at 90 degrees Make sure the original remote has fresh batteries Hold down the button on the original remote for longer and release only after the green LED lights on the module 9 TC2 CTL3_manual_en Module learns code but doesn t Re program the buttons control the projector If you programmed in simple mode try programming in advanced mode Use external IR blaster Check IR blaster cable to make sure i
7. me with projection screens are often RF not IR To control these screens use the 12v trigger RS 232 Professional control format used to control a variety of devices including projectors More reliable than IR and uses two way communication with the control device to confirm commands has been received Requires 3 core cable Limited cable lengths NOTE If using RS 232 the TC2 CTL3 needs to be mains powered 12v Trigger Simple trigger voltage commonly used to activate projection screens Requires 2 core unshielded cable NOTE If using 12v Trigger the TC2 CTL3 needs to be mains powered RS 485 Using the same codes as RS 232 this protocol offers longer cable distances of around 100m and only requires 2 core cable Few AV devices can decode RS 485 If using an additional Control module to extend the keypad this terminal is used to connect the Slave module to the master NOTE If using RS 485 the TC2 CTL3 needs to be mains powered 5 TC2 CTL3_manual_en INSTALLATI ON 1 FIT LABELS Use flat head screwdriver to unclip clear button covers then apply labels as shown 2 SELECT POWER SOURCE The control module is set to be powered by mains power by default If you choose to power with 2 x AAA batteries not included move switch inside the battery compartment to BATT NOTE 1 If powered by batteries buttons will only light when pressed NOTE 2 If powered by mains ensure batteries are not left in device 3 CON
8. or 12v trigger Add an extension keypad Program scheduled actions Duplicate to multiple devices LOAD SOFTWARE ONTO PC Download from Vision s website www visionaudiovisual com techconnect tc2 ctl3 CONNECT CONTROL MODULE VIA USB In the battery compartment there is a standard USB B mini connector USB cable not included The software can be used without a control module connected but if learning IR codes you will need to connect a control module LAUNCH SOFTWARE You can create a new program edit program saved on PC or edit program saved on device VISTON Pr Ex tere On Kay pad Cikcoobiuionb ed A second Taciconneci Costui device n bm weed to mata rei the bey ped No stored on t ogam cats tension teayped arm ali e commande CIRO Kca 5 6 Tacr onnect Como cansend coma nce a Lecheduled Sem Cith ro 10 setup START BY ASSIGNING CODES click a button A window will open which will allow you to set the codes for that button Once you have finished the button will be blue to show codes are allocated LEARNING CODES When learning IR codes from an original remote connect TC2 CTL3 to PC via USB External power is not required for the module Set power switch to PWR 8 TC2 CTL3 manual en NOTE When you press learn in software wait until the red LED appears on the module then point original remote at front of module and press and hold button 6 SCHEDULE LAST If using the schedu
9. t hasn t been damaged 10 TC2 CTL3_manual_en SPECI FI CATIONS PRODUCT DIMENSIONS 71 x 42 x 31mm length x width x height PRODUCT WEIGHT 63 grams CONSTRUCTION MATERIAL Plastic COLOUR White POWER SUPPLY 100 240v AC 50 60Hz External Power Supply integrated transformer plug type DC Output 12V 0 5A DC Cable 3m Transformer size 62 x 42 x 22 mm Interchangeable prongs including UK EU AU US Note a normal figure 8 cable can be plugged into the transformer if preferred POWER CONSUMPTION Static lt 5uA Sending lt 20mA Copying lt 10Ma COMPLIANCE RoHS WEEE amp CE Compliant ACCESSORIES INCLUDED 5 x Blanking buttons 1 x Labels 1 x Single Gang Techconnect Backbox 1 x Single Gang Techconnect Surround 1 x IR Blaster with 150mm cable terminated with female minijack 1 x IR Blaster with 10m cable WARRANTY This product comes with a 2 year return to base warranty effective from the date of purchase This warranty applies only to the original purchaser and is not transferable For the avoidance of doubt this will be taken from the information held by the appointed national distributor at the point of sale If the product is DOA dead on arrival you have 21 days from purchase date to notify the national distributor via your AV reseller The liability of the manufacturer and its appointed service company is limited to the cost of repair and or replacement of the faulty unit under warranty except for d
10. w editions of the User Manual 12 TC2 CTL3 manual en
Download Pdf Manuals
Related Search