Paxton Net2Air bridge Ethernet, PoE
Contents
1. not be effective until the Net2 Server has been restarted Cancel Apply Cancel opi Click on Detect and the MAC address of the device s will appear in the table You must then use the IP address configuration tab to manually assign the IP address subnet mask and gateway Be aware that if the IP address that you give the device is not in the same IP range as the PC the device will no longer respond until you connect to it with a PC that is in the same IP range Some firewall virus protection software and other wireless hardware can block the IP detection process Disable these and try to detect the device again Please contact Technical Support if you require further advice If you detect the MAC address but the device now shows Not Responding you must check the IP address to make sure it is still in range with the PC or network If it is not you should either change the IP address of the PC or the IP address of the device so they are both again in the same range Our Technical team can talk you through this if you need help If the MAC address does not appear when you click Detect ensure that the following ports are open on all devices between this unit and the Net2 PC If you still cannot detect the MAC address of the device connect it directly to your PC via a network cable and call our Technical Help line Connecting to a WAN or different subnet mask If you are connecting this device to a remote subne2. 05 07 2012 Wp Ins 30175 Net2Air Ethernet bridge in plastic housing axton Technical Support 01273 811011 Support paxton co uk Technical help is available Monday Friday from 07 00 19 00 GMT Saturday from 09 00 13 00 GMT Documentation on all Paxton products can be found on our website http www paxton co uk Enclosure Software Requires Net2 v4 14 or later Net2Air wireless communication The access control unit connects to the Net2 system using Paxton Net2Air proprietary wireless technology through a Net2Air bridge Radio signals do not always behave as you might expect For example a mobile phone that displays a full signal on one part of the site will lose signal completely only a few metres away These problems can be addressed by using the Net2 site surveyor kit 690 200 See also AN1095 Net2 wireless access control How does it work lt http paxton info 974 gt AN1096 How to plan a Net2 wireless installation lt http paxton info 975 gt Ins 30096 Net2Air site surveyor lt http paxton info 1015 gt Radio frequency This product should not be installed within 3 metres of other wireless equipment operating on a 2 4Ghz frequency To ensure optimum performance other wireless networks should avoid WiFi channels 1 2 and 3 to reduce the possibility of interference Net2Air Site Surveyor 690 200 This access control unit uses wireless communication It is recommended that a Net2Air site sur
3. t which is different from the Net2 software PC the standard detect mechanism cannot work across the network routers between them The IP address along with the correct Subnet mask and gateway for the remote subnet have to be set Either do this on the local subnet with the existing Net2 PC or use a PC on the remote subnet once the device is installed The PC that has the Net2 server installed must be able to access the IP address range on the WAN remote site This may require the routers and gateways to be configured between the networks Again this would be done by the Network administrator of that site Make sure the ports listed above are open on all intermediate routers Once installed create a record with the Add button if none was created during initial set up and you should then be able to detect its MAC by entering the IP address in the Configuration screen Ping box LED indications 4 secxze 1099909 pe Power aa i s j 4 des An EAN o eee ja E V k J t i Q a 7 a f Maes TTE Ce i SEBS aL 2 i AS Eeka E k oe s Reset button Power LED Server Connected The TCP IP interface is communicating with the PC Net2 server TCP IP LAN connection Net2Air wireless activity Tx Rx Blue Data Reset To clear all settings back to their factory default including clearing the current IP address and setting the bridge to acquire new addresses using DHCP power on the uni
4. t with the reset button held down for 3 seconds The unit will beep to acknowledge once the reset is complete Sounder The device will beep when detected by the Net2 Server Configuration Utility or when new IP settings are applied The sounder will also respond to a direct Ping over the network This is a feature to assist with finding devices hidden from view Specifications System Specification Min ACU s per Net2Air bridge Recommended 1 Net2Air USB bridge per system Net2Air Ethernet bridge per system Carrier frequency 2 405 GHz 30 m Max 10 1 100 Net2Air wireless range ax M Min Dc supply voltage o f o ooe owo S O besu py cure O oo o o oma S O Min Max Operating temperature o o o o o se Waterproof i Length Width Height TS om om O o This product is not suitable for retail sale All warranties are invalid if this product is not installed by a competent person C 0889 The declaration of conformity is available on request Contact details are provided at http paxton info 596
5. veyor is used to determine the best position for the bridge and control units Connecting to the PC via the Ethernet port The IP address should be assigned a fixed value or should be given a DHCP reservation Unreserved IP addresses issued by DHCP servers are not guaranteed to be constant leading to potential failure of communication between Net2 software and the bridge Run the Net2 Server Configuration Utility Start Programs Net2 and Click on Net2Air Bridge Q Net2 Server Configuration Utility a a a gt o Ds General Database Wiegand Dial up nodes TCP IP node Net2Air Bridge Paths System Features Diagnosti_4 gt m Net24ir Bridges Name Serial number MAC address IP Address Net2air Bridge 904962 904962 00 CF D6 0D CF 02 10 10 25 19 M Net2Air Bridge 904962 904962 00 CF D6 0D CF 02 10 10 25 19 Configuration IP address configuration Configuration IP address configuration You can get an IP address assigned automatically if your network supports this capability Otherwise you need to ask Serial number 304362 your network administrator for an IP address Name Net2 ir Bridge 904962 IP Address 10 10 25 13 C Obtain an IP address automatically use DHCP MAC address 00 CF D6 0D CF 02 Use the following IP address Subnet 255 255 0 0 IP Address i E ON E rA a AE fs Ping Gateway 0 0 0 0 Subnet 255 255 0 0 7 Gateway 0 0 0 0 Changes to the Net24jir Bridges IP configuration will
Download Pdf Manuals
Related Search