Ergotron 97-729
Contents
1. 12345 NOTE User should 1 Enter Master PIN then press 1 change Master PIN 2 Numbers 3 and 5 on the Keypad will start flashing indicating the Master PIN has been accepted upon receipt of cart 3 Simultaneously press 3 and 5 while they are flashing 4 Allthe numbers will light you have 3 seconds to enter a PIN 5 Enter anew PIN any sequence of 5 numbers The first PIN programmed is the new Master PIN 6 When the PIN is accepted all of the LEDs will flash once in acknowledgement you have 3 seconds to enter the next PIN 7 You can then proceed to program up to 11 PINs by repeating steps 5 and 6 8 When finished entering new PINs system will exit program mode after 3 seconds with a series of LED flashes Unlock Drawer 3 methods e Enter Master PIN then press desired drawer number e Enter User PIN then press desired drawer number e Key turn clockwise 1 4 turn Drawer Numbers Lock Drawer 2 methods Erase All Personal PINs cannot erase only one PIN or Master e Wait 4 seconds for drawer to lock automatically PIN e Press 1 and 2 on number pad simultaneously 1 Enter Master PIN then press 1 2 Press 3 and 5 simultaneously while blinking 3 Press 1 and 2 simultaneously Lost Master PIN Contact Ergotron Customer Care for instructions Drawer Troubleshooting Flashing LED Meaning Key pad numbers are dark 1 Drawer is open Touch anywhere on number pad to activate back light drawer remains 1 amp 2 Waiting for2. rev C 12 12 4 10 LiFe Powered Carts SLA Powered Carts gt 8 On Powered Carts only reset drawer power so keypad will recognize added drawer NOTE This step is not needed on Non Powered Carts A Turn off all mounted equipment b Disconnect Power System from power source C Turn power system off by holding down the AC Outlet Power button for 1 3 seconds Power light will shut off Unplug drawer power cable and a then plug it back in to reset E GEAR VIEW 888 97 283 G 00 rev C 12 12 5 10 SLA Powered Carts SS On Powered Carts only reset drawer power so keypad will recognize added drawer NOTE This step is not needed on Non Powered Carts a Turn off all mounted equipment b Disconnect Power System from power source um A e Se olding down the AC Outlet Power button for 1 3 seconds Power light will shut off E Unplug drawer power cable and then plug it back in to reset 888 97 283 G 00 rev C 12 12 6 10 9 LIFT TENSION Fy AFTER SET UP Adjustment CUSTOMER H A 822 421 00 It is important that you adjust this product according to the weight of the mounted equipment as described in the following steps Any time equipment is added or removed from this product resulting in a change in the weight of the mounted load you should repeat these adjustment steps to ensure safe and optimum operation Adjustments should move smoothly and easily through the fu
3. drawer selection see Unlock Drawer locked until you enter valid PIN 3 amp 5 Unit is ready to program master or user PINs see Programming New PIN Check to make sure battery pack is connected 5 Drawer is unlocked PIN is accepted but drawer does not open All New PIN accepted Make sure drawer is fully closed before entering PIN Drawer won t open when User PIN is entered Test system by entering Master PIN If drawer doesn t unlock contact Ergotron customer care for Lost Master PIN instructions 888 97 283 G 00 rev C 12 12 9 10 10 10 ERGOTRON 2012 Ergotron Inc All rights reserved While Ergotron Inc makes every effort to provide accurate and complete information on the installation and use of its products it will not be held liable for any editorial errors or omissions including those made in the process of translation from English to another language or for incidental special or consequential damages of any nature resulting from furnishing this instruction and performance of equipment in connection with this instruction Ergotron Inc reserves the right to make changes in the product design and or product documentation without notification to its users For the most current product information or to know if this document is available in languages other than those herein please contact Ergotron No part of this publication may be reproduced stored in a retrieval system or transmitted in any form or by an
4. e Heer Guide ERGOT ROI Y StyleView Supplemental Drawer GH www ergotron com USA 1 800 888 8458 N Europe 31 0 33 45 45 600 www ergotron com China 86 769 86018920 User s Guide English Guia del usuario Espanol Manuel de l utilisateur Francais Gebruikersgids Nederlands Benutzerhandbuch Deutsch Guida per l utente Italiano Anvandarhandbok svenska UOUUUUU UU UUUU UI For service and warranty visit www ergotron com Si desea informacion de servicio y garantia visite www ergotron com Pour toute question concernant la garantie ou le service client consultez www ergotron com Weitere Informationen zu Service und Gew hrleistung erhalten Sie unter www ergotron com Ga voor service en garantie naar www ergoton com Per assistenza e la garanzia visitare www ergotron com Ga in pa www ergotron com for service och garanti T EABKO REC OLY CEL CIE www ergotron com ZS CES TEE ARREAK WWE www ergotron com SD2 r E LC saaa or lt 2 lbs 1 kg lt 0 25 Ibs 0 1 kg Total weight capacity per drawer Total weight capacity per drawer 10 5 267 mm 10 5 267 mm 12 5 3 75 315 mm 96 mm SSE 888 97 283 G 00 rev C 12 12 1 10 14mm 9 16 el IMPACT HAZARD MOVING PARTS CAN CRUSH AND CUT A CAUTION Close worksurface before opening drawers Open only one drawer at a time Do Not Minimize Lift Tension BEFORE Remov
5. eck to make sure DC cable is connected e Drawer won t open when User PIN is entered Test system by entering Master PIN If drawer doesn t unlock contact Ergotron customer care for Lost Master PIN instructions Lights Meaning 1 2 3 4 5 or 6 and Red mute button Flashing and alarm sounding Drawer is open longer than 20 seconds Mute button can be pressed to mute alarm System will not function until drawer is shut and locked The number corresponding to the open drawer will Flash Red on the keypad All available drawer numbers Flashing Green Waiting for drawer selection see Unlock Drawer All available drawer numbers Flashing Red Firmware upgrade is happening All flash once New code accepted All flash three times Exiting program mode 888 97 283 G 00 rev C 12 12 8 10 Non Powered Carts AutoLock Drawer Battery Pack d CAUTION Only use rechargeable batteries Using non 4X rechargeable batteries may cause product damage Before the Auto Lock Drawer will function you will need to charge the ALD batteries for at least 1 or 2 hours To charge ALD batteries computer needs to be powered on and connected to the USB hub AA Rechargeable Nickel Metal Hydride USB to computer USB to charge ALD batteries S CAUTION Open only one drawer at a time Do Not push cart when drawers are open Failure to follow these instructions may cause the cart to be unstable Programming New PIN Default Master PIN
6. ime All numbers will light green You have 5 seconds to enter the new Master PIN 5 Input new 5 digit Master PIN All numbers will flash green 6 Wait 5 seconds for system to exit program mode All numbers will flash green several times Programming User PINS 1 Enter Master PIN All numbers associated with available drawers will light 2 Simultaneously press 4 and 6 Numbers 4 and 6 will light green 3 Simultaneously press 4 and 6 again Numbers 4 and 6 will flash green 4 Simultaneously press 4 and 6 a third time All numbers will light green You have 10 seconds to enter a new User PIN 5 Input new 5 digit User PIN All numbers will flash green You can continue to enter 5 digit User PINs until finished After sitting idle for 10 seconds system will exit program mode All numbers will flash green several times NOTE System will hold up to 100 User PINs Once 100 User PINs storage is exceeded the oldest User PIN will be overwritten by the next User PIN programmed Unlock Drawer 3 methods e Enter Master PIN then press desired drawer number e Enter User PIN then press desired drawer number e Key turn clockwise 1 4 turn j Drawer Numbers Lock Drawer e Wait 4 seconds for lock to engage automatically NOTE Drawer must be fully closed to lock Drawer Troubleshooting e Key pad numbers are dark Touch anywhere on number pad to activate back light drawer remains locked until you enter valid PIN Ch
7. ing Mounted Equipment push cart when drawers or worksurface are open Failure to follow these instructions may cause es the cart to be unsta ble To Minimize Lift Tension 1 Lower worksurface to lowest position 2 Turn adjustment nut at top of riser counterclockwise until it stops Adjustment may require 40 60 revolutions Failure to heed this warning may result in serious personal injury or property damage For More information and instructions refer to product guide at http 4support ergotron com or contact Ergotron Customer Care at 1 800 888 8458 822 052 3 Drawers M4 x 12mm ES 14mm 9 16 888 97 283 G 00 rev C 12 12 2 10 Slide the drawer only half way onto the bottom tracks of the top drawer control panel on the top drawer Remove the top cover on the top drawer and route Vay the cable attached to the bottom drawer up into the D GA IMPORTANT If you have a six drawer configuration you will need to unplug the top drawer cable from the up arrow jack and plug it into the down arrow jack Then plug the bottom drawer cable into the up arrow jack 888 97 283 G 00 rev C 12 12 3 10 3 Slide the drawer completely onto the bottom tracks of the top drawer 4 Replace the top cover on the top drawer 5 Remove the i top drawer s Secure the bottom drawer by attaching the two screws 6 F Replace the top drawer s 888 97 283 G 00
8. ll range of motion and stay where you set it If adjustments are difficult and do not stay in the desired position follow the instructions to loosen or tighten the tension to create a smooth easy adjustment motion Depending on your product and the adjustment it may take several turns to notice a difference Lift Up and down Release Brake to move riser ar NOTE Adjustment may require 40 60 revolutions 14mm 9 16 4 888 97 283 G 00 rev C 12 12 7 10 Powered Carts Non Powered Carts gt NOTE User should change Master Personal Identification Number OGRE HEH PIN upon receipt of cart Lost Master PIN Contact Ergotron Customer Care for instructions 1x Ensure that the main power system batteries are installed and functioning The power does not need to be turned on at the power system user interface CAUTION Close worksurface before opening drawers Open only one drawer at a time Do Not push cart when drawers or worksurface are open Failure to follow these instructions may cause the cart to be unstable Set up Master PIN for the First Time Default Master PIN 12345 Contact Ergotron Customer Care for instructions if Master PIN is lost 1 Enter Master PIN All numbers associated with available drawers will light 2 Simultaneously press 3 and 5 Numbers 3 and 5 will light green 3 Simultaneously press 3 and 5 again Numbers 3 and 5 will flash green 4 Simultaneously press 3 and 5 a third t
9. y means electronic mechanical photocopying recording or otherwise without the prior written consent of Ergotron Inc 1181 Trapp Road Eagan Minnesota 55121 USA Patents Pending and Patented U S amp Foreign Ergotron is a registered trademark of Ergotron Inc Americas Sales and Corporate Headquarters St Paul MN USA 800 888 8458 1 651 681 7600 www ergotron com sales ergotron com APAC Sales Tokyo Japan www ergotron com EMEA Sales Amersfoort The Netherlands 31 33 45 45 600 www ergotron com info eu ergotron com Worldwide OEM Sales www ergotron com info cem ergotron com apaccustomerservice ergotron com 888 97 283 G 00 rev C 12 12
Download Pdf Manuals
Related Search