Home

AMX HPG-10, 100 pack

image

Contents

1. y Ze Overview The HPG 10 3 4 Mini Grommets FG570 01 10K are an elegant means to control cables in conference rooms meeting rooms and personal workspaces HPG 10 3 4 Mini Grommets are designed to be mounted into a variety of surfaces such as a conference room table desk or lectern in order to manage A V power and or networking cables FIG 1 HPG 10 3 4 Mini Grommet Product Specifications HPG 10 Specifications Dimensions HWD e Max above mounting surface 08 2mm 1 1 27mm Diameter 1 2 13 mm N A e Table Cutout Dimensions 3 4 19mm Round Hole Weight 10z 05 Kg Installation e Max below mounting surface e Mounting surface footprint e Min mounting surface thickness e Max mounting surface thickness Tools Required e Drill e 93 4 Drill bit Forstner Auger or Spade Bit CAUTION This installation requires specific woodworking skills This installation should be performed by an experienced person comfortable with these types of woodworking operations Improper installation may result in damage to the mounting surface AMX is not responsible for damage caused by improper installation Read these instructions in their entirety before beginning the installation The installation requires specific steps to be performed in specific order 1 Select a Suitable Location for the HPG 10 e Note the space requirements for installing the system FIG 2 e Note that the HPG 10 requires 0 2 5mm
2. above the mounting surface 2 Drill The Hole In The Mounting Surface Note AMX recommends a high quality name brand Forstner Bit Auger Bit or Spade Bit to create the 3 4 19mm hole Some lower quality drill bits may create torn edges or a slightly larger hole which will cause the HPX 10 to fit loosely in the hole or expose edges of the cut If in doubt test the drill bit for proper fit before drilling into the final mounting surface 1 Carefully measure the tabletop or other mounting surface to locate the desired position of the HPG 10 Take care to ensure that the top surface of the mounting surface is not damaged beyond the width of the trim bezel as the cutout is made 2 Use an appropriate drill and 3 4 19mm drill bit to drill a 3 4 hole in the mounting surface e Make sure cutting tool used is appropriate for the material to be cut and will not tear or chip the top surface e Note that the process of making the cutout will create substantial dust and prepare the environment appropriately For full warranty information refer to the AMX Instruction Manual s associated with your Product s 10 11 2011 AMX All rights reserved AMX and the AMX logo are registered trademarks of AMX AMX reserves the right to alter specifications without notice at any time 3000 RESEARCH DRIVE RICHARDSON TX 75082 800 222 0193 fax 469 624 7153 technical support 800 932 6993 e www amx com Installation Guide HPG 10 Hydraport 3 4
3. inch Mini Grommet 0 75 19 050 OEE 12 700 FIG 2 HPG 10 Installation Specifications 3 Insert the Cables and Install the Mini Grommet For cables for which the far end of the cable is not accessible either because the cable has been run under carpet is in a conduit or structure or is otherwise fixed the cable must be placed through the cutout in the table prior to installation see FIG 2 1 Place the cable through the mounting surface 2 Place each half of the HPG 10 Mini Grommet on either side of the cable and press the two halves together they will interlock 3 Press the assembled HPG 10 Mini Grommet into the 3 4 hole FIG 3 The fit of the grommet in the hole should be snug FIG 3 Topside of Installed Unit 93 0570 02 REV A NU Aa IAR

Download Pdf Manuals

image

Related Search

Related Contents

転写パットリくん A3フラットベッドスキャナー Ver.2  Disque Dur Multimédia Movie Cube D120H/D850H  PONT L`EVEQUE 2005  SP 350 Repair Manual  Graco 310643T User's Manual  SBM 42 - Lidl Service Website  ファイル名:gozonjidesuka サイズ:4.89 メガバイト  Mode d`emploi du test de fertilité FertiQUICK    

Copyright © All rights reserved.
Failed to retrieve file