Miele DA 420 V cooker hood
Contents
1. dai1692b The control module is fitted in the tower after the cover plate has been unscrewed from the ceiling The control module is supplied with its own detailed operating and installation instructions 35 Connection for air extraction N Important To avoid the danger of toxic fumes please observe the Warning and Safety instructions This is especially crucial when using the cooker hood at the same time as another heating appliance which relies on air from the same room The cooker hood should be installed according to local and national building regulations Seek approval from the building inspector where necessary All ducting pipework and fittings must be of non flammable materials The exhaust ducting should be as short and straight as possible To ensure efficient air extraction the diameter of the exhaust ducting should not be less than 150 mm If exhaust ducting with a diameter of less than 150 mm or if flat ducting is used the noise level of the cooker hood will increase and extraction will be less efficient Only reduce the diameter of the ducting if absolutely necessary e g where narrower ducting has already been installed Only use wide radius bends Tight bends reduce the air throughput of the cooker hood Only use smooth pipes or flexible hoses made from non flammable materials for extraction connection 36 Where ducting is horizontal it must be laid to sl2. P Always switch the cooker hood on when a cooking zone is in use otherwise condensation may collect in the hood which could cause corrosion P When cooking with oil or fat chip pans and deep fat fryers etc do not leave the pans unattended Never leave an open grill unattended when grilling Overheated oil and fat can ignite and could set the cooker hood on fire P Do not use the cooker hood without the filters in place This way you will avoid the risk of grease and dirt getting into the appliance and hindering its smooth operation P The filters should be regularly cleaned or changed as appropriate Saturated filters are a fire hazard See Cleaning and care P The cooker hood can get very hot during cooking due to heat rising from the hob Do not touch the housing or the grease filters until the cooker hood has cooled down P Do not use a steam cleaner to clean this appliance Steam could reach the electrical components and cause a short circuit Correct installation P Refer to the cooker or hob manufacturer s instructions as to whether a cooker hood may be operated above the cooker hob P The minimum safety distances between the top of the cooker or hob and the bottom of the cooker hood given in the Appliance dimensions section of this booklet must be maintained unless the hob manufacturer states that a greater safety distance is required If more than one cooking appliance is fitted b
3. or if itis no longer effective in absorbing kitchen odours It should however be replaced at least every 6 months Used charcoal filters can be disposed of with the normal household waste m After fitting the new charcoal filter press the charcoal filter touch control for approximately 3 seconds to re set the operating hours counter The indicator lamp will go out m f a charcoal filter is replaced before the operating hours counter has reached its maximum the charcoal filter touch control should be pressed for approximately 6 seconds to reset the counter 25 Cleaning and care Changing a halogen lamp m Before any cleaning or maintenance work disconnect the cooker hood from the mains supply Ensure that itis switched off at the isolator or the screw out fuse is removed in countries where this is applicable N Exercise caution when changing halogen lamps They get very hot during use and remain hot for some time after being switched off Let them cool down before you change them Do not touch the surface directly when changing a lamp as grease particles from your fingers will adhere to the surface and damage it Please follow the manufacturer s instructions 26 dai2328 dai2329 m To access the halogen lamp push the lamp cover gently upwards The cover will open and can be pulled down m Pull the old halogen lamp out of the connection socket an
4. www miele co nz Singapore Miele Southeast Asia Miele Pte Ltd 163 Penang Road 04 02 03 Winsland House Il Singapore 238463 Tel 65 6735 1191 Fax 65 6735 1161 E Mail infosea miele com sg nternet www miele sg South Africa iele Pty Ltd 63 Peter Place Bryanston 2194 P O Box 69434 Bryanston 2021 Tel 27 0 11 548 1900 Fax 27 0 11 548 1935 E mail infoQmiele co za nternet www miele co za United Arab Emirates Miele Appliances Ltd P O Box 11 47 82 Gold amp Diamond Park Sheikh Zayed Road Building 6 Offices Nos 6 214 to 6 220 Dubai Tel 971 4 341 84 44 Fax 4971 4 341 88 52 E Mail infoQmiele ae Internet www miele ae Alteration rights reserved 4309 Ce M Nr 07 261 480 04
5. 6 P Installation maintenance and repairs may only be carried out by a Miele authorised person in accordance with current national and local safety regulations Repairs and other work by unqualified persons could be dangerous The manufacturer cannot be held liable for unauthorised work P Faulty components must only be replaced by genuine Miele original parts The manufacturer can only guarantee the safety of the appliance when Miele replacement parts are used P During installation maintenance and repair work the appliance must be disconnected from the mains electricity supply It is only completely isolated from the electricity supply when itis switched off at the isolator or the screw out fuse is removed in countries where this is applicable or the mains fuse is disconnected or itis switched off at the wall socket and the plug withdrawn or the fuse from the fused spur connection unit is withdrawn Warning and Safety instructions P Do not connect the appliance to the mains electricity supply by a multi socket unit or an extension lead These do not guarantee the required safety of the appliance e g danger of overheating P For appliances with an external fan motor fitted EXT models the connection of the two units must be made using the connection cable and the plug connectors These models may only be combined with a Miele external motor P This applian
6. Press the On Off touch control to switch the fan off 5415 co o m Press the run on option touch control and the grease filter touch control at the same time The indicator lamp for the grease filter touch control and one of the touch control lamps will flash 2 085000 The control lamps show the time which has been set 1st lamp from the left 20 hours 2nd lamp from the left 2 30 hours 3rd lamp from the left 2 40 hours 4th lamp from the left 2 50 hours m Use the touch controls to select the desired time o m Confirm the selection by pressing the grease filter touch control All the indicator lamps will go out If you do not confirm your selection within 4 minutes the cooker hood will automatically revert to the original setting Use Setting and altering the charcoal m Use the touch controls to select filter operating hours counter the desired time with recirculation mode The charcoal filter is needed for recirculation mode The cooker hood is set at the factory for m Confirm the selection by pressing the extraction mode On delivery the charcoal filter touch control operating hours counter for the charcoal filter is set to unlimited ANE MAICA TRENDS IU GeO For recirculation mode the operating If you do not confirm your selection hours counter needs to be set to the within 4 minutes the cooker hood required time will automatically
7. level 42 Touch control for the run on option The fan can be set to switch off automatically after either 5 or 15 minutes 49 Touch control for the grease filters The indicator lamp for the grease filter touch control lights up when the grease filters need to be cleaned This control is used to reset the operating hours counter after cleaning the grease filters see Cleaning and care It can also be used to check and alter the operating hours counter 43 Touch control for the charcoal filter DA 420 V only The indicator lamp for the charcoal filter touch control lights up when the charcoal filter used in recirculation mode needs to be replaced For this to happen the operating hours counter needs to be set before the appliance is used for the first time The control is used to reset the operating hours counter after replacing the charcoal filter see Cleaning and care It can also be used to check and alter the operating hours counter 49 Controls for raising and lowering the canopy The height of the canopy can be adjusted by up to 260 mm this can be extended to 300 mm see Installation For information about using the appliance see Operation Miele home Con ctivity dai2385 This cooker hood is communication enabled Communication module XKM 2000 DA available as an optional extra enables the operation of the cooker hood to be automatically c
8. mm0 0 SSD 4 screws 8 x 60 mm with 4 washers and 4 plugs S 10 to secure the cover plate to the ceiling NThe screws and plugs are for use in concrete ceilings only For other types of construction alternative suitable fixings will be required Make sure the ceiling is strong enough to bear the weight of the cooker hood 30 2 screws M4 x 8 mm for securing the tower c 4 spacers to use in the event of an uneven ceiling 1 floating bracket to give a choice of position for the exhaust cut out in the ceiling 1 hose clip for securing the exhaust ducting to the exhaust stub Special installation instructions for recirculation mode In order to use the cooker hood in recirculation mode it has to be fitted with a special conversion kit which is available from the Spare Parts Department see Technical data It is supplied with its own fitting instructions After the cooker hood has been installed the charcoal filter has to be fitted and the operating hours counter has to be set See Cleaning and Care and Filter operating hours counter Installation Extending or limiting the adjustment range The height range for the appliance can be extended or limited by moving the limit switch It may be necessary to do this if the distance between the hob and the canopy when it is lowered is less than the minimum safety disance required By moving the limit switch the height range for the app
9. required Touch control higher setting Touch control lower setting Depending on the intensity of the cooking vapours levels to Ill green indicator lamps are usually sufficient for normal cooking Intensive setting When frying or cooking food with a strong aroma you may wish to select the Intensive setting yellow indicator lamp for a short period Automatic switch off of the Intensive setting You can set the Intensive setting so that it only runs for 10 minutes before reverting automatically to level Ill m To set this option both the fan and the hob lighting must be switched off 5215 606 m Press the run on option touch control for approximately 10 seconds The first fan setting indicator will light up m hen press one after the other the hob lighting touch control 0000 the touch control and the hob lighting touch control again Use 2 0000 w The indicator lamps for fan power levels and IV will flash if the automatic switch off of the Intensive setting is not activated m Press the touch control to activate automatic switch off The indicator lamps for fan power levels and IV will now light up constantly Press the touch control to deactivate the automatic switch off function m Press the run on option touch control to confirm your selection If you do not confirm your selection within 4 minutes the cooker ho
10. revert to the original setting D e m Press the On Off touch control to switch the fan off SA o0 amp D m Press the run on option touch control and the charcoal filter touch control at the same time The indicator lamp for the charcoal filter touch control and one of the lamps above the touch controls will flash 00009 The control lamps show the time which has been set 1st lamp from the left 120 hours 2nd lamp from the left 2 180 hours 3rd lamp from the left 240 hours Ath lamp from the left unlimited 20 Use Adjusting the height of the canopy The height adjustment feature on the canopy can be used to adapt the height of the hood to suit the installation conditions adjust the working area underneath the hood to the height of the user maximise vapour extraction by lowering the canopy during particularly intensive cooking create more working space above the hob by raising the canopy when required The height of the canopy can be adjusted by up to 260 mm this can be extended to 300 mm see Installation m he canopy can be raised or lowered by touching the Up or Down controls briefly m Pressing the control again stops the canopy If itis not stopped the canopy will automatically be raised or lowered to its fullest extent Repeated use of the height adjustment feature over several minutes will cause it
11. the brightness to the level required and then release it If you keep the touch control pressed in the light will continually change between bright and dim To switch the lighting off m Press the hob lighting touch control briefly to switch the lighting off The indicator lamp will go out Safety cut out Should the cooker hood be left on the fan will switch off automatically after 10 hours The lighting will remain on D e m Pressing the On Off touch control will switch the fan back on again Use Filter operating hours counter The number of hours the appliance has been in operation is stored in memory eG o The indicator lamp for the grease filter touch control will come on after 30 hours of operation The grease filters must then be cleaned Afterwards the filter operating hours counter must be reset m o do this press and hold the grease filter touch control for about 3 seconds The indicator lamp for the touch control will go out For recirculation mode the operating hours counter for the charcoal filter needs to be set to the required time see Setting and altering the charcoal filter operating hours counter GG e eJ The indicator lamp for the charcoal filter touch control will light up after the cooker hood has operated for the number of hours set The charcoal filter must then be replaced with a new one Afterwards the filter operating hours counter must be rese
12. Miele Operating and installation instructions Cooker hoods DA 420 V DA 420 V EXT DA 424 V DA 424 V EXT To avoid the risk of accidents en GB AU NZ or damage to the appliance it is essential to read these instructions before it is installed and used for the first time M Nr 07 261 480 Contents Caringfortheenvironment 4 Warning and Safety instructions 5 Modesofoperation 11 Guidetotheappliance 12 Mieledehome 14 AA en ta trie aro aa Bunt aod CES daa Ca Der we e ite gas 14 USG oco ev Pa PERRA REPE eg Bae La mera eee ees ER 15 To Switeh thedati OE x asco etc te oy at e ea oer do m bae RO a deles 15 To Selecta power level sa cited tex td RC tt P c e pat Bede 15 Intensive soting uua ceo kapa e Ra em cd co d c RU OR UR i en 15 Fi rizori OptlOFi atrae Reged IA 16 To witeh thiedal Of aee itte eee etr od ace ao er dob eet qa epos 16 To Switch the lighting oni easet eriei enie e obe Pen 17 Dimming the liGhtihG i52 dee AI e bees 17 To switch the lighting off iilii 17 Filter operating hours counter 18 Adjusting the height of the canopy 21 Cleaning and care 22 FIOUSING Su deg e
13. and Safety instructions Technical safety P Before installation check the cooker hood for visible signs of damage Under no circumstances should you use a damaged appliance A damaged appliance is dangerous P Before connecting the appliance to the mains supply make sure that the voltage and frequency details given on the data plate correspond with the on site electricity supply otherwise the appliance could be damaged Consult a qualified electrician if in any doubt P The electrical safety of this appliance can only be guaranteed when continuity is complete between it and an effective earthing system which complies with current local and national safety regulations It is most important that this basic safety requirement is present and tested regularly and where there is any doubt the household wiring system should be inspected by a qualified electrician The manufacturer cannot be held liable for the consequences of an inadequate earthing system e g electric shock P For safety reasons this appliance may only be used when it has been fully installed P Only open the housing as described in the instructions given in the installation sheet and in the Cleaning and care section of this booklet Under no circumstances should any other parts of the housing be opened Tampering with electrical connections or components and mechanical parts is highly dangerous to the user and can cause operational faults
14. bove 28 Appliance dimensions Safety distance between hob and cooker hood S The minimum safety distances between the top of a cooker or hob and the bottom of the cooker hood are as follows unless a greater distance is specified by the manufacturer of your cooking appliance 550 mm GB 600 mm AU NZ above electric hobs and cookers 650mm above an open grill or deep fat fryer 650mm above gas hobs and cookers If this cooker hood is installed above a Miele Wok CS 1028 CombiSet appliance a minimum safety distance of 760 mm must be maintained between the burner and the lower edge of the cooker hood For further advice see Warning and Safety instructions If the distance falls below the recommended safety distance when the canopy is lowered the maximum interval it is allowed to be lowered must be re set during installation see Installation 29 Installation Before installation it is important to read the information given on the following pages as well as the Appliance dimensions and the Warning and Safety instructions at the beginning of this booklet This is particularly crucial when using the cooker hood at the same time as a heating appliance that relies on oxygen from the same room to avoid the danger of toxic fumes building up Installation instructions See enclosed Installation sheet for instructions on how to install this appliance Assembly parts
15. ce may only be used in mobile installations such as ships caravans aircraft etc if a risk assessment of the installation has been carried out by a suitably qualified engineer P In areas which may be subject to infestation by cockroaches or other vermin pay particular attention to keeping the appliance and its surroundings in a clean condition at all times Any damage which may be caused by cockroaches or other vermin will not be covered by the guarantee Using at the same time as other heating appliances that depend on the air from the room Warning danger of toxic fumes AS L RH t rom d A188 0000 NY dai1474 P Great care should be taken when using the cooker hood at the same time and in the same room or area of the house as another heating appliance which depends on the air in the room Such appliances include gas oil wood or coal fired boilers and heaters continuous flow or other water heaters gas hobs cookers or ovens which draw air in from the room and duct exhaust gases out through a chimney or extraction ducting When used in extraction mode with or without an external motor fitted the appliance draws air in from the room in which it is installed and from neighbouring rooms If there is insufficient air an underpressure will occur The heating appliance may be starved of oxygen impairing combustion Harmful gases could be drawn out of th
16. d replace it with a new one 20 W G 4 fitting m Push the cover back up and make sure it clicks into place After Sales Service In the event of a fault which you cannot correct yourself or if the appliance is under guarantee please contact Your Miele Dealer Chartered Agent or The Miele Customer Contact Centre see back cover for address When contacting your Dealer or Miele please quote the model and serial number of your appliance These are shown on the data plate which is visible when the grease filter is removed For G B Please note that telephone calls may be monitored and recorded for training purposes 27 Appliance dimensions 1 Cut out for feeding through the exhaust ducting the mains cable and with EXT models the connection cable to the external motor In recirculation mode only the mains cable is required 2 Height range for appliance in extraction mode the appliance is delivered with this height range as standard 3 Height range for appliance in recirculation mode 4 Possible height range for appliance in extraction mode see Installation 5 Ventilation grille positioned at the top for recirculation DA 420 V Exhaust connection 150 mm not Ceiling fixing viewed from above needed for recirculation mode 260 O i O 1 NA ra UR 260 4 910 9 A gos n 90 4 730 02 70 190 DA 424 V Ceiling fixing viewed from a
17. e chimney or extraction ducting back into the room with potentially fatal consequences Warning and Safety instructions In order to ensure safe operation and to prevent gases given off by the heating appliances from being drawn back into the room when the cooker hood and the heater are in operation simultaneously an underpressure of 0 04 mbar 4 pa is the maximum permissible in the room dai1477 Ventilation can be maintained by air inlets which must not be blocked in windows doors and outside wall vents or by other technical measures such as ensuring that the cooker hood can only be switched on when the heating appliance is switched off or vice versa A ventilation brick alone is not generally sufficient to ensure safe ventilation NThe overall ventilation condition of the dwelling must be taken into account If in any doubt the advice of a competent builder or for gas a qualified gas fitter registered with an official gas safety body in accordance with national safety regulations must be sought One of the following technical measures may be necessary to ensure safe operation f the only way of ensuring adequate ventilation is via an open window a window contact switch should be fitted to ensure that the cooker hood can only operate when the window is opened sufficiently Take care when ventilating the room through an open window that
18. e ducting system It can be sited at any suitable position in the ducting system between the cooker hood and the external motor on EXT model cooker hoods On extraction models it can be fitted nearest the ducting outlet to the outside to reduce neighbourhood noise 37 Technical data Total connected load 455 W Fari motor ccc ve wkd ees 200 W Variable height motor 175 W Hob lighting 4x 20W VONAGE asin D AC 230 V FIGQUENCY esa erat E Rae 50 Hz Fuse rating GB 00 5A AUS NZ Pl g rating csse siati 10A Test marks Electrical safety RESUME B uod Rab dona e dans C Tick Mark Electrically suppressed according to AS NZS 1044 Weight DA 420 V II 42 kg DA 420 V EXT 38 8 kg DA 424V 0 0 00 ee 47 kg DA 424 V EXT 43 8 kg 38 Fan performance Extraction power according to EN 61591 Extraction system 2 150 mm L vell Jua Rex 200 m3 h Level Wily ciem RE RS 320 m n Level Il 480 m3 h Intensive Setting 700 m h Unrestricted 730 m3 h Recirculation with charcoal filter Levell 150 m3 h LevellI 260 m3 h Level Il 400 m3 h Intensive Setting 500 m h Optional extras for recirculation mode Conversion Kit DUI 31 Miele charcoal filter DKF 12 1 For EXT models the connected load and extraction power will d
19. eneath the cooker hood and they have different minimum safety distances to the cooker hood select the greater distance Warning and Safety instructions P Safety regulations prohibit the fitting of a cooker hood over solid fuel stoves P All ducting pipework and fittings must be of non flammable material These can be obtained from the Miele Spare Parts department or from builders merchants P The appliance must not be connected to a chimney or vent flue which is in use Neither should it be connected to ducting which ventilates rooms with fireplaces gt If exhaust air is to be extracted into a chimney or ventilation duct no longer used for other purposes seek professional advice Accessories P Only use genuine Miele spare parts and accessories with this appliance If spare parts or accessories from other manufacturers are used this will invalidate the guarantee and Miele cannot accept liability The manufacturer cannot be held liable for damage caused by non compliance with these Warning and Safety instructions 10 Modes of operation The cooker hood works with air extraction quw The air is drawn in cleaned by the grease filters and directed outside The cooker hood is fitted with a non return flap which is closed when the cooker hood is switched off No exchange of room air and outside air can take place When the cooker hood is switched on the non return flap opens for t
20. epend on the type of external motor fitted Length of connection cable to external MOLOG sus onere e a SCRI s 1m 39 United Kingdom Miele Co Ltd Fairacres Marcham Road Abingdon Oxon OX14 1TW Tel 0845 365 0555 Fax 0845 365 0777 Customer Contact Centre Tel 0845 365 6600 E mail info miele co uk Internet www miele co uk Australia Miele Australia Pty Ltd ABN 96 005 635 398 1 Gilbert Park Drive Knoxfield VIC 3180 Tel 03 9764 7130 Fax 03 9764 7149 Internet www miele com au China Miele Shanghai Suite 4105 06 Plaza 66 1266 Nanjing Road West Jing An District Shanghai 200040 PRC Tel 86 21 6288 4200 Fax 86 21 6288 4100 E mail mieleshanghai cn miele com Internet www miele cn Hong Kong Miele Hong Kong Limited AIA Plaza 24 Floor 18 Hysan Avenue Causeway Bay Tel 852 2610 1331 Fax 852 2610 1013 E mail mielehk miele com hk Internet www miele hk India Miele Appliances India Pvt Ltd Ground Floor Copia Corporate Suites Plot No 9 Jasola New Delhi 110025 Tel 011 46 900 000 Fax 011 46 900 001 E mail customercare miele in Internet www miele in Ireland Miele Ireland Ltd Broomhill Road Tallaght Dublin 24 Tel 01 461 0710 Fax 01 461 07 97 E Mail info miele ie Internet www miele ie New Zealand Miele New Zealand Limited Unit L 10 20 Sylvia Park Road Mt Wellington 1060 Auckland NZ Tel 0800 264 353 Fax 0800 463 453 Internet
21. from materials which are environmentally friendly for disposal and can normally be recycled Packaging e g cling film polystyrene and plastic wrappings must be kept out of the reach of babies and young children Danger of suffocation Dispose of or recycle all packaging materials safely as soon as possible Disposal of your old appliance Electrical and electronic appliances often contain materials which if handled or disposed of incorrectly could be potentially hazardous to human health and to the environment They are however essential for the correct functioning of your appliance Please do not therefore dispose of it with your household waste Please dispose of it at your local community waste collection recycling centre or contact your dealer for advice Ensure that it presents no danger to children while being stored for disposal It should be unplugged or disconnected from the mains electricity supply by a competent person Warning and Safety instructions This appliance complies with all relevant local and national safety requirements Inappropriate use can however lead to personal injury and damage to property To avoid the risk of accidents and damage to the appliance please read these instructions carefully before using it for the first time They contain important information on the safety installation use and maintenance of the appliance Keep these instructions in a safe place and ensu
22. h stainless steel housing This infomation does not apply to the controls Stainless steel surfaces can be cleaned using the Miele E cloth or with a proprietary non abrasive cleaning agent designed specifically for use on stainless steel To help prevent re soiling a conditioning agent for stainless steel can also be used Apply sparingly following the instructions on the label If too much conditioning agent is used traces of it may appear in the area where the canopy rises and falls Cleaning and care Controls The controls may suffer discolouration or damage if soiling is left on them for too long Remove soiling straight away Observe the General notes on cleaning earlier in this section Do not use stainless steel cleaning agents on the controls Grease filters Re usable metal filters are fitted which remove solid particles oil dust etc from the kitchen vapours preventing soiling of the cooker hood oj The grease filters should be cleaned regularly at least every 3 4 weeks to avoid a build up of grease However they should be cleaned immediately if the grease filter touch control lamp comes on N An oversaturated filter is a fire hazard dai2051 m To take out the grease filters release the locking clip on the filter lower the filter 45 unhook it at the back and remove it To avoid damaging the filter or the hob below make sure you hold the fi
23. he cooking vapours to be blown directly outside air recirculation Applies to the DA 420 V only A conversion kit and charcoal filter are required which are available as optional accessories see Technical Data URE The air is drawn in and cleaned first by the grease filters and then by a charcoal filter The cleaned air is then recirculated back into the kitchen through grilles in the top of the cooker hood telescopic tower Before using the cooker hood in recirculation mode ensure that the charcoal filter is in place See Cleaning and care an external motor EXT models only uw EXT models are designed to be connected to an external motor located outside the room The external motor is connected to the cooker hood by means of a control cable and is operated by the controls on the cooker hood Guide to the appliance Guide to the appliance Cover plate 2 Telescopic tower 8 Canopy The canopy is not designed to be used as a shelf 4 Grease filters 8 Charcoal filter Available as an optional accessory for recirculation mode DA 420 V only Recirculation grille only for recirculation mode on the DA 420 V Controls Hob lighting Touch control for hob lighting This control switches the lighting on and off and is also a dimmer switch On Off touch control for the fan Touch controls to select the fan power
24. liance can be limited the canopy will not be lowered as far a greater adjustment range is required the canopy will be lowered further A maximum appliance height of 1030 mm is possible for extraction mode only not possible for recirculation mode m Install the cooker hood according to the installation instructions supplied m Press the Down button to lower the canopy The canopy will be lowered to its fullest extent Miele dai2257 m Remove the grease filters m Remove the cooker hood tower fixing screw Ensure that the tower is held securely while carrying out the following steps Danger of inury dai2258 00 o0 dai2259 m Now secure the tower with the screw you removed earlier 31 Installation dai2260 o 6666 o 6666 dai2261 2 dai2262 eo m Secure the limit switch opposite the guide on the telescopic tower see illustration m Raise and lower the canopy and check that the limit switch is working dai2263 m Remove the safety screw and push the tower downwards m f a greater safety distance S between the canopy and the hob is required raise the canopy until the required safety distance has bee
25. lter securely at all times when handling it 23 Cleaning and care Cleaning the grease filters by hand m Clean the filters with a soft nylon brush in a mild solution of hot water and a small amount of washing up liquid Do not use undiluted washing up liquid cleaning agents containing descaling agents powder cleaners cream cleaners or abrasive all purpose cleaning agents oven sprays Cleaning the grease filters in the dishwasher m Place the filters as upright as possible in the lower basket with the short sides upright and wash on a 65 C programme ensuring the spray arm is not obstructed If a Miele dishwasher is being used select the Sensor wash programme m Use a mild dishwasher detergent Depending on the cleaning agent used cleaning the filters in a dishwasher can cause permanent discolouration to the surface However this will not affect the functioning of the filters in any way m After cleaning leave the filters to dry on an absorbent surface before replacing them 24 m When removing the filters for cleaning also clean off any residues of oil or fat from the now accessible housing to prevent the risk of these catching fire dait619 When putting the grease filters back in position ensure that the locking clips are facing down towards the hob If the grease filters are inadvertently replaced upside down insert a small screwdriver blade i
26. n reached m f a greater adjustable range is required lower the canopy A maximum appliance height of 1030 mm is possible 32 dai2264 m hen secure the tower with the safety screw again Replace the grease filters Electrical connection All electrical work should be undertaken by a suitably qualified and competent person in strict accordance with current national and local safety regulations BS 7671 in the UK Installation repairs and other work by unqualified persons could be dangerous for which the manufacturer cannot be held liable Ensure power is not supplied to the appliance until after installation or repair work has been carried out Do not connect the appliance to the mains electricity supply by an extension lead These do not guarantee the required safety of the appliance The voltage and connected load are given on the data plate This is visible when the grease filters have been removed Ensure that these match the household mains supply Connection of this appliance should be made via a suitable isolator or a double pole fused spur connection unit which complies with national and local safety regulations and the On Off switch should be easily accessible after the appliance has been built in When switched off there must be an all pole contact gap of 3 mm in the switch including switch fuses and relays according to EN 60 335 If the switch is not accessible afte
27. nto the slits to disengage the clip m After replacing the grease filters press the grease filter touch control for approximately 3 seconds to re set the operating hours counter The indicator lamp will go out If the grease filters are cleaned before the operating hours counter has reached its maximum the grease filter touch control should be pressed for approximately 6 seconds to reset the counter Cleaning and care Fitting and replacing the charcoal filter If the cooker hood is connected for recirculation a charcoal filter must be inserted in addition to the grease filters It is designed to absorb cooking odours It is fitted in the canopy above the grease filters New filters can be purchased from your Miele Dealer Chartered Agent or from the Miele Spare Parts Department See back cover for contact details and Technical data for the model number of the filter m Before fitting or replacing a charcoal filter the grease filters must first be taken out see previous section for instructions on how to do this m ake the charcoal filter out of its packaging ead SE dai1671 m insert the charcoal filter into the canopy When fitting for the first time m Set the operating hours counter to suit your requirements see Operation Always replace the charcoal filter im mediately if the indicator lamp for the charcoal filter touch control lights up
28. od will automatically revert to the original setting 16 Run on option It is advisable to run the fan for a few minutes after cooking has finished to neutralise any lingering odours in the air whether you are using air extraction or recirculation mode The fan can be set to switch off automatically after either 5 or 15 minutes 5115 66 m After cooking has finished press the run on option touch control whilst the fan is still running Press once The fan will switch off after 5 minutes left hand indicator lamp Press twice The fan will switch off after 15 minutes right hand indicator lamp To switch off the run on option press the run on option touch control again The appliance will then not switch off automatically To switch the fan off D e m Press the On Off touch control to switch the fan off The indicator lamp will go out Use To switch the lighting on The hob lighting can be switched on and off independently of the fan m Briefly press the lighting touch control to switch on the hob lighting The indicator lamp will come on The lighting will switch on at maximum brightness Dimming the lighting The brightness of the lighting can be adjusted m With the lighting switched on press and hold the hob lighting touch control in The brightness will gradually dim until you release the touch control m Press the touch control in again to increase
29. ontrolled by the operating status of a Miele electric hob with onset controls For communication to take place the hob must be fitted with communication module XKM 2000 KM The hob transmits information about its operating status to the cooker hood via the household power supply Powerline 14 When the hob is switched on the cooker hood lights and the fan also comes on During cooking the cooker hood automatically sets its power level according to the number of cooking zones in operation and their power levels After switching the hob off the fan and the hob lighting will switch off automatically after a period of time For detailed information about this function please read the separate instruction booklet supplied with the XKM 2000 DA communication module The communication module is fitted to the cooker hood in the area of the motor and is connected to the controls of the cooker hood This module must be installed by a Miele service technician or suitably qualified electrician Use To switch the fan on m Press the On Off touch control The fan runs at power level II The indicator lamp will come on If the cooker hood has been connected to a window contact switch via the DSM 400 control module then the fan cannot be switched on if the window is shut The indicator lamp will flash To select a power level 6 000 m Use the controls to select the power level
30. ope away at at least 1 cm per metre This is to ensure that condensate cannot drain back into the cooker hood If the exhaust air is to be ducted into the open air the installation of a telescopic wall vent is recommended 2 E s f the exhaust air is to be ducted into a vent flue the ducting must be directed in the flow direction of the flue Connection for air extraction Important If the exhaust ducting is to run through rooms ceiling space etc where there may be great variations in temperature between the different areas the problem of condensation will need to be addressed The exhaust ducting will need to be suitably insulated Condensate trap optional accessory dai1585 In addition to insulating the exhaust ducting we recommend that a suitable condensate trap is also installed to collect and evaporate any condensate which may occur Condensate traps are available for 125 mm or 150 mm ducting When installing a condensate trap ensure that it is positioned vertically and if possible directly above the exhaust connection The arrow on the housing indicates the direction of air flow Cooker hoods designed for use with an external motor EXT models have an integrated condensate trap Silencer optional accessory dai2003 To achieve even further reductions in noise levels a special silencer can be fitted in th
31. r installation depending on country an additional means of disconnection must be provided for all poles For extra safety it is advisable to install a residual current device RCD with a trip current of 30 mA Important AUS This appliance is supplied for connection to an a c single phase 230 V 50 Hz supply The wires in the mains lead are coloured in accordance with the following code Green yellow earth Blue neutral Brown live WARNING THIS APPLIANCE MUST BE EARTHED 33 Operation with DSM 400 control module The Miele DSM 400 control module can be used to combine the cooker hood with other components It enables the following Connection to a window contact switch If adequate ventilation to the room can only be ensured by having a window open when the cooker hood is in use at the same time as a heating appliance which depends on the air from the same room then the control module can be used to connect a window contact switch not supplied to the appliance Once connnected the cooker hood can only be operated when the window is sufficiently open see also Warning and Safety instructions When the window is closed the cooker hood fan cannot be switched on The indicator lamp for the On Off touch control on the cooker hood will flash The same applies to operation with an external motor depending on model The cooker hood lighting is not affected by this EXT models can al
32. re that all users are familiar with the contents Pass them on to any future owner of the appliance Correct application P This appliance is intended for domestic use only Any other usage is at the owner s risk and could be dangerous The manufacturer cannot be held liable for damage resulting from incorrect or improper use or operation P This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience or knowledge unless they are supervised whilst using it or have been shown how to use it correctly by a person responsible for their safety Safety with children P This appliance is only intended for use by adults who have read these instructions P This appliance is not a toy To avoid the risk of injury keep children well away and do not allow them to play with it or to use the controls They will not understand the potential dangers posed by it They should be supervised whenever you are working in the kitchen P Older children may use the cooker hood only when its operation has been clearly explained to them and they are able to use it safely recognising the dangers of misuse P Please be aware that on cooker hoods with halogen lighting the lamps will get very hot during use and remain hot for some time after switching off To safeguard against burning keep children well away from the lamps at all times Warning
33. so be connected to a window contact switch Take care when ventilating the room through an open window that ventilation is not impaired by a closed blind or curtain 34 If the control module is disconnected in order to operate the cooker hood without the window contact switch e g after moving house the cooker hood electronics must be reset by a Miele service technician Potential free connection This enables a further appliance to be controlled by the switch setting on the cooker hood fan For instance it can be used to ensure a sufficient supply of fresh air when the cooker hood and a heating appliance which also depends on the air in the room are being used together by switching on an air intake fan or opening a motorised inlet flap as soon as the cooker hood fan is switched on It is important to ensure that the fan power is sufficient and that the air intake has a suitable cross sectional diameter If a sufficient air intake cannot be guaranteed then the potential free contact will enable a heating appliance which depends on air in the same room as a cooker hood to be switched off when the cooker hood is in operation See also Warning and Safety instructions Operation with DSM 400 control module Connection to a light switch The control module can be used to Switch on the cooker hood lighting and also to dim it depending on model via a light switch in the house Installation
34. t m Press the charcoal filter touch control for about 3 seconds The indicator lamp for the touch control will go out 18 Reading the filter operating hours counter To check the percentage of time set already used o m Press the On Off touch control to switch the fan on e o o m Press and hold the grease filter or the charcoal filter touch control 0G000 E One or more of the indicator lamps for the touch controls will flash The number of flashing lamps shows the percentage of the operating time which has already been used up 1llamp 25 2lamps 50 3lamps 75 4lamps 100 The number of operating hours used remains in the memory even when the appliance is switched off or there is a power cut Use Filter operating hours counter You can set the operating hours counter to suit the type of cooking you do Select a short time if you roast or fry a lot f you use very little fat for cooking select a longer time If you only cook occasionally we recommend that you still select a short time because grease which has built up gradually over a long period of time will harden on the grease filter and make cleaning more difficult Altering the grease filter operating hours counter The operating hours counter for the grease filter is set at 30 hours The time set can be lengthened or shortened you can choose 20 30 40 or 50 hours m
35. t o ede ona ce a UA Ode OR ERE sd e b a OR Dd AS 22 Greasefilters 23 Fitting and replacing the charcoalfilter 25 Changing a halogen lamp Aa e 26 After Sales Service 27 Appliance dimensions 28 Safety distance between hob and cooker hood S 29 Installation ini oed Reb SERE b Ie bach ALIA 30 Installation instructions usse eene mask dox ghe x x ohne p hc E Rom wa 30 Assembly DANS x aque g aedi ee ortos ede GE or cen D Ice o Ret qne ra 30 Special installation instructions for recirculationmode 30 Extending or limiting the adjustment range 31 Electrical connection II UWA dakaten 33 Contents Operation with DSM 400 control moduee 34 Connection to a window contact Switch 34 Potential free connection 34 Connectiontoalightswitch 35 Connection for air extraction 36 Condensate trap lisse 37 AA UE ABA NI KUNATA MANA ETENIM 37 Technical data 38 Caring for the environment Disposal of the packing material The transport and protective packing has been selected
36. to cut out It can be used again after a pause 21 Cleaning and care Before carrying out any cleaning or maintenance work disconnect the cooker hood from the mains supply Ensure that itis switched off at the isolator or the fuse is withdrawn from the fused spur connection unit or the mains fuse is disconnected or the screw out fuse is removed in countries where this is applicable A range of Miele branded cleaning and conditioning agents are available to order through your Miele Dealer Chartered Agent the Miele Spare Parts Department or via the internet on www miele shop com Housing General notes The surfaces and controls are susceptible to scratches and abrasions Please observe the following cleaning instructions m All external surfaces and controls can be cleaned with warm water and a small amount of washing up liquid applied with a well wrung out soft sponge or cloth m Wipe the surfaces dry using a soft cloth Do not use too much water when cleaning the controls Water could penetrate into the electronics and cause damage 22 Avoid cleaning agents containing soda acids chlorides or solvents abrasive cleaning agents e g powder cleaners or cream cleaners and abrasive sponges as well as pot scourers or sponges which have been used previously with abrasive cleaning agents These will damage the surface material Important for appliances wit
37. ventilation is not impaired by a closed blind or curtain The cooker hood can be set up to automatically switch on an air intake fan or open a motorised inlet flap when it is switched on The cooker hood can be set up to automatically switch off a heating appliance which also depends on the air from the room when it is switched on The Miele DSM 400 control module offers the possibility of combining other components with the cooker hood see Operation with Control module DSM 400 It is available to purchase as an optional extra If in any doubt the advice of a competent builder or for gas a qualified gas fitter must be sought If the hood is being operated in recirculation mode the above restrictions do not apply Warning and Safety instructions Correct use P Never use an open flame beneath the cooker hood To avoid the danger of fire do not flamb or grill over an open flame When switched on the cooker hood could draw flames into the filter Fat particles drawn into the cooker hood present a fire hazard P When using the cooker hood over a gas hob ensure that any burners in use are always covered by a pan Switch the cooking zone off when a pan is removed even for a short time Regulate the flame so that it does not burn up the sides of the pan Do not allow the pans to overheat excessively e g when using a wok The cooker hood can become damaged when exposed to excessive heat
Download Pdf Manuals
Related Search