Rose CrystalView DVI Multi
Contents
1. and Operations Manual Figure 1 Typical connections The following Installation steps should be used as a guideline to properly install the CrystalView DVI Multi transmitter and receiver units It is recommended that the same type of monitors be connected to all of the Receiver units Refer to figure 5 1 Remove power from the computer and all monitors Connect a DVI D mm cable from the computer DVI D video out connector to the Transmitter s DVI IN connector 3 Connect a monitor to the DVI OUT connector on the Transmitter See EDID Learning Apply power to the monitor Connect the supplied power adapter to the Transmitter and a power source Upon power up the Transmitter will Learn the EDID specifications of the monitor connected to the DVI OUT connector 6 Remove the monitor from the Transmitter and connect it to a Receiver units DVI OUT connector 7 Connect a shielded CAT6 or better cable from the RJ45 connector on the Transmitter to the RJ45 connector on the Receiver 8 Connect the supplied power adapter to the Receiver and a power source 9 Make sure power is applied to the Transmitter Receiver s and all connected DVI monitors then boot the computer OI gt You should see the boot up seguence on all connected monitors NOTE The CrystalView DVI Multi will automatically read on power up the EDID information from any monitor connected to the Transmitters DVI OUT connector and save the information If no m2. in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense IBM AT and PS 2 are trademarks of International Business Machines Corp Microsoft and Microsoft Windows are registered trademarks of Microsoft Corp Any other trademarks mentioned in this manual are acknowledged to be the property of the trademark owner Copyright Rose Electronics 2010 All rights reserved No part of this manual may be reproduced stored in a retrieval system or transcribed in any form or any means electronic or mechanical including photocopying and recording without the prior written permission of Rose Electronics Rose Electronics Part MAN CRVDVIMUL Printed In the United States of America Revision TABLE of CONTENTS Contents Page System Introduction veri ica nennen 1 RUIT 2 Package Contents lea 2 Additional Items needed na n n nana naa nannaa anne 2 Rose Electronics web inia nannaa 2 Product Registration isc ie daa 2 Models sikti a it 3 Product AStallaAtION Re 4 EDI
3. CrystalView DVI Multi INSTALLATION AND OPERATIONS MANUAL 2 ROSE ELECTRONICS u 10707 Stancliff Road Phone 281 933 7673 Houston Texas 77099 WWW ROSE COM LIMITED WARRANTY Rose Electronics warrants the CrystalView Multi to be in good working order for one year from the date of purchase from Rose Electronics or an authorized dealer Should this product fail to be in good working order at any time during this one year warranty period Rose Electronics will at its option repair or replace the Unit as set forth below Repair parts and replacement units will be either reconditioned or new All replaced parts become the property of Rose Electronics This limited warranty does not include service to repair damage to the Unit resulting from accident disaster abuse or unauthorized modification of the Unit including static discharge and power surges Limited Warranty service may be obtained by delivering this unit during the one year warranty period to Rose Electronics or an authorized repair center providing a proof of purchase date If this Unit is delivered by mail you agree to insure the Unit or assume the risk of loss or damage in transit to prepay shipping charges to the warranty service location and to use the original shipping container or its equivalent You must call for a return authorization number first Under no circumstances will a unit be accepted without a return authorization number Contact an authorized repair c
4. D Learning aan n cnn an naan nana a nana 4 Maintenance and Repair n aina n aan naan aa aan annan naan naan 6 Technical SUPP OMT ka an 6 SLE 7 Safety and EMC Regulatory Statements 8 Figures Page Figure 1 Typical connections seeeeeene nennen 5 Appendices Page Appendix A General 9 INTRODUCTION Disclaimer While every precaution has been taken in the preparation of this manual the manufacturer assumes no responsibility for errors or omissions Neither does the manufacturer assume any liability for damages resulting from the use of the information contained herein The manufacturer reserves the right to change the specifications functions or circuitry of the product without notice The manufacturer cannot accept liability for damages due to misuse of the product or other circumstances outside the manufacturer s control The manufacturer will not be responsible for any loss damage or injury arising directly or indirectly from the use of this product System Introduction The CrystalView DVI Multi from Rose Electronics is the perfect addition to your video distribution system Whether you are enhancing an existing system or designing a new video distribution system the CrystalView DVI Multi can easily integrate int
5. ION Product Installation Figure 1 shows a typical installation of the CrystalView DVI Multi using the x2 model All models install in the same manor The x1 model uses 1 CAT6 cable from the transmitter to one receiver the x2 model uses 2 CAT6 cables from the transmitter to two receivers the x4 model uses 4 CAT6 cables from the transmitter to four receivers the x8 model uses 8 CAT6 cables from the transmitter to eight receivers Each CAT6 cable can be up to 220 feet in length It is recommended that all monitors connected to the receiver unit s 1 2 4 or 8 be the same make model and type of monitor EDID Learning procedure The CrystalView DVI Multi has its own built in EDID table and uses these monitor specifications in place of the actual monitor s EDID specifications The Transmitter unit can Learn the monitor s EDID specifications and provide these to the computer so the correct resolutions and refresh rates can be used To set up the Transmitter to Learn the monitor s EDID specifications connect the DVI monitor to the DVI OUT connector on the transmitter and apply power to the Transmitter On power up the CrystalView DVI Multi will read and store the EDID specifications of any monitor connected to the DVI OUT connector If no monitor is connected to the DVI OUT connector during power up the internal EDID information is not modified N b W gt gt e 0 E CrystalView DVI Multi Installation
6. enter or Rose Electronics for further information ALL EXPRESS AND IMPLIED WARRANTIES FOR THIS PRODUCT INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED IN DURATION TO A PERIOD OF ONE YEAR FROM THE DATE OF PURCHASE AND NO WARRANTIES WHETHER EXPRESS OR IMPLIED WILL APPLY AFTER THIS PERIOD SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU IF THIS PRODUCT IS NOT INGOOD WORKING ORDER AS WARRANTED ABOVE YOUR SOLE REMEDY SHALL BE REPLACEMENT OR REPAIR AS PROVIDED ABOVE IN NO EVENT WILL ROSE ELECTRONICS BE LIABLE TO YOU FOR ANY DAMAGES INCLUDING ANY LOST PROFITS LOST SAVINGS OR OTHER INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OF OR THE INABILITY TO USE SUCH PRODUCT EVEN IF ROSE ELECTRONICS OR AN AUTHORIZED DEALER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR FOR ANY CLAIM BY ANY OTHER PARTY SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR CONSUMER PRODUCTS SO THE ABOVE MAY NOT APPLY TO YOU THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH MAY VARY FROM STATE TO STATE NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated
7. er if any of the following conditions occur The power cord or connection cables are damaged or frayed The Unit has been exposed to any liquids The Unit does not operate normally when all operating instructions have been followed The Unit has been dropped or the case has been damaged The Unit exhibits a distinct change in performance indicating a need for service CrystalView DVI Multi Installation and Operations Manual Safety and EMC Regulatory Statements Safety information A Documentation reference symbol If the product is marked with this symbol refer to the product documentation to get more information about the product WARNING A WARNING in the manual denotes a hazard that can cause injury or death CAUTION A CAUTION in the manual denotes a hazard that can damage equipment Do not proceed beyond a WARNING or CAUTION notice until you have understood the hazardous conditions and have taken appropriate steps Grounding These are Safety Class products There must be an un interruptible safety earth ground from the main power source to the product s input wiring terminals power cord or supplied power cord set Whenever it is likely that the protection has been impaired disconnect the power cord until the ground has been restored Servicing There are no user serviceable parts inside these products Only service trained personnel must perform any servicing maintenance or repair The user may adjust
8. iew DVI Multi video extender splitter has been tested for conformance to safety regulations and requirements and has been certified for international use Like all electronic equipment the CrystalView DVI Multi should be used with care To protect yourself from possible injury and to minimize the risk of damage to the Unit read and follow these safety instructions Follow all instructions and warnings marked on this Unit Except where explained in this manual do not attempt to service this Unit yourself Do not use this Unit near water Assure that the placement of this Unit is on a stable surface or rack mounted Provide proper ventilation and air circulation Keep power cord and connection cables clear of obstructions that might cause damage to them Use only power cords power adapter and connection cables designed for this Unit Use only a grounded three wire electrical outlet Use only the power adapter provided with the CrystalView DVI Multi Keep objects that might damage this Unit and liquids that may spill clear from this Unit Liquids and foreign objects might come in contact with voltage points that could create a risk of fire or electrical shock Operate this Unit only when the cover is in place Do not use liquid or aerosol cleaners to clean this Unit Always unplug this Unit from its electrical outlet before cleaning Unplug this Unit from the electrical outlet and refer servicing to a qualified service cent
9. o your system and provide perfect DVI video quality to all connected displays If you need to extend a single video to a remote monitor the CrystalView DVI Multi single model works perfectly for the task If you have multiple monitors that you need to display information to the x2 x4 and x8 models can handle the job With all models you can view locally what is being distributed to the remote monitors The remote displays can be extended up to 220 feet away from the controlling computer This is ideal for many applications where the controlling computer needs to be remotely located in a secure area away from the DVI displays especially in a retail environment All models offer a local DVI connection for viewing on a locally connected DVI monitor CrystalView DVI Multi Installation and Operations Manual Features x1 x2 x4 and x8 models available Supports resolutions up to 1920 x 1200 Splits and extends DVI D single link video signal up to 220 feet 67m Image quality does not degrade over all resolutions Local DVI video connection Supports single link DVI D computers Status indicator shows power and loss of signal Automatic EDID learning feature for supporting any DVI monitor Mac and PC DVI D support Package Contents Transmitter unit as ordered Receiver units as ordered 5VDC power adapter Installation manual Additional Items needed Computer with DVI D output CAT6 STP cable s DVI D mm cable Local DVI D monito
10. onitor is connected the internal EDID data will not be modified CrystalView DVI Multi Installation and Operations Manual EX SUPPORT and MAINTENANCE Maintenance and Repair This Unit does not contain any internal user serviceable parts In the event a Unit needs repair or maintenance you must first obtain a Return Authorization RA number from Rose Electronics or an authorized repair center This Return Authorization number must appear on the outside of the shipping container See Limited Warranty for more information When returning a Unit it should be double packed in the original container or equivalent insured and shipped to Rose Electronics Attn RA 10707 Stancliff Road Houston Texas 77099 USA Technical Support If you are experiencing problems or need assistance in setting up configuring or operating your CrystalView DVI Multi consult the appropriate sections of this manual If however you require additional information or assistance please contact the Rose Electronics Technical Support Department at Phone 281 933 7673 E Mail TechSupport rose com Web www rose com Technical Support hours are from 8 00 am to 6 00 pm CST USA Monday through Friday Please report any malfunctions in the operation of this Unit or any discrepancies in this manual to the Rose Electronics Technical Support Department E CrystalView DVI Multi Installation and Operations Manual SAFETY Safety The CrystalV
11. only items mentioned in this manual EN CrystalView DVI Multi Installation and Operations Manual APPENDICES Appendix A General Specifications Resolution Singlelink 1920 x 1200 60Hz Video compatibility DVI D Interconnect cable CATE shielded Max cable length 220 feet 67 meters Power 90 240 VAC input 5VDC output Dimensions Height Width Depth Weight in mm in mm in mm 16 kg x1 0 8 22 0 3 44 87 3 2 8 71 0 0 2 0 1 x2 1 6 42 0 5 30 135 0 2 9 75 0 1 0 0 45 x4 1 6 42 0 7 38 201 6 3 56 90 5 2 1 0 95 x8 1 75 44 5 9 8 249 0 5 0 127 0 2 4 1 22 Operating Temp 32 104 0 40 Storage Temp 4 122 20 50 Relative Humidity Approvals Appendix B Part Numbers Part Number Description Kits CRK 21DLC 1x Transmitter 1x Receiver CRK 22DLC 1x Transmitter 2x Receiver CRK 24DLC 1x Transmitter 4x Receiver CRK 28DLC 1x Transmitter 8x Receiver CRV DL1DLC Transmitter 1 Port RJ45 CRV DL2DLC Transmitter 2 Port RJ45 CRV DL4DLC Transmitter 4 Port RJ45 CRV DL8DLC Transmitter 8 Port RJ45 CRV SRDLC Receiver CrystalView DVI Multi Installation and Operations Manual ES NOTES CrystalView DVI Multi Installation and Operations Manual 10707 Stancliff Road Phone 281 933 7673 Houston Texas 77099 WWW ROSE COM
12. r optional Rose Electronics web site Visit our web site at www rose com for additional information on the CrystalView DVI Multi and other products offered by Rose Electronics that are designed for data center applications classroom environments digital wall signage display systems industrial and military systems and many other access switching and extending applications Product Registration Register your Rose Electronics products online at www rose com htm online registrationform htm and take advantage of the following Rose Electronics standard warranty Plus Free lifetime firmware updates Free lifetime technical support 30 day money back guarantee Priority First In Line status for technical support E CrystalView DVI Multi Installation and Operations Manual MODELS Models Front View Connectors m Rear View DVI In I DVI Out DVI IN DV OUT __ Power 5VDC X1 Transmitter Part Number CRV DL1DLC Front View Connectors RJ45 Link 1 RJ45 Link 2 DVI In DVI Out Power 5VDC X2 Transmitter Part Number CRV DL2DLC Front View Connectors RJ45 Link 1 RJ45 Link 2 RJ45 Link 3 RJ45 Link 4 DVI In DVI Out Power 5VDC X4 Transmitter Part Number CRV DL4DLC Front View Connectors RJ45 Link 1 Rear View DVI Out Power 5VDC OUT SVDC Receiver for All Models Part Number CRV SRDLC CrystalView DVI Multi Installation and Operations Manual ES INSTALLAT
Download Pdf Manuals
Related Search