Nilfisk E 130.2-9 X-TRA
Contents
1. and other accessories in the holders of the machine Should the machine by mistake be frozen it will be necessary to check it for damage NEVER START UP A FROZEN MACHINE Frost damages are not covered by the guarantee carefully up 1 Wind up the electric cable on the appropriate hooks Built in clip for good holding 1 The lower hook can be turned to release the electric cable 2 The high pressure washer comes in two models A with hook for storage of high pres sure hose 14 B with a hose reel 13 The standard accessories spray gun f spray lance a nozzles b foam sprayer c can be stored on the pressure washer The nozzle cleaning tool d and a Click amp Clean brush e can also be stored on the product 12 7 Maintenance WARNING Always disconnect the electrical plug from the socket prior to maintenance or cleaning To ensure a long and problem free working life please take the following advice e Wash out water hose high pressure hose spray lance and accessories before mounting 7 1 Cleaning of water inlet filter D JD 7 2 Cleaning of nozzle 7 3 Cleaning of machine vents The machine should be kept clean so as to let cooling air 7 4 Greasing of couplings To ensure an easy connec tion and that o rings do not amp Clean the connectors of dust and sand Make sure that no sand or dirt is blocking the2. movement of the pawl on the Click amp Clean spray lance e Rinse the detergent spraying attachment after use amp Clean the nozzles Any repair should always be made in an authorized work shop with original spare parts Clean the water inlet filter regu larly once a month or more fre quently according to use Care fully loosen the filter with a pair of pliers and clean it Check that it is intact before re mounting it The inlet filter must always be fitted inside the water inlet pipe to filter out sand limestone and other impurities as they will damage the pump valves CAUTION Failure to fit the filter will invalidate the guarantee A clogging up in the nozzle Causes a pump pressure which is too high This is why cleaning is required immediately 1 Stop the machine and dis connect the nozzle 2 Clean the nozzle IMPOR TANT The cleaning tool 11 should only be used when the nozzle is detached 3 Flush the nozzle backwards with water pass freely through the ma chine vents dry up the couplings should be greased regularly 13 END 8 Trouble shooting To avoid unnecessary disappointments you should check the following before contacting the Nilfisk service organization Symptom Machine refuses to start Fluctuating pressure Motor busses Machine stops Fuse blows Machine pulsating Machine often starts and stops by itself Machine starts but no water comes out Ca
3. 2 Clean the filter See section 7 1 Straighten out hose Contact your nearest Nilfisk Service Centre Wait for pump hoses or accessory to thaw Connect inlet water Clean the filter see section 7 1 Clean the nozzle see section 7 2 In case problems other than the above occur please contact your local Nilfisk distributor UK Customer Services at Penrith 01768 868995 14 9 Further information 9 1 Recycling the washer 9 2 Warranty conditions Make the old cleaner unusable immediately 1 Unplug the cleaner and cut the electric cable Do not discard electrical appli ances with household waste Nilfisk guarantees high pres sure washers for domestic use for 2 years If your high pres sure washer or accessories are handed in for repair a copy of the receipt must be enclosed Guarantee repairs are being made on the following condi tions e that defects are attributable to flaws or defects in materi als or workmanship wear and tear as well as misuse are not covered by the guar antee e that the directions of this instruction manual have been thoroughly observed e that repair has not been car ried out or attempted by oth er than Nilfisk trained service staff e that only original accessories have been applied amp that the product has not been exposed to abuse such as knocks bumps or frost As specified in European Direc tive 2002 96 EC on old electri cal and electronic
4. CO See illustration at the end of this manual Start stop switch Water inlet with filter High pressure connection only models without hose reel High pressure hose Electric cable Click amp Clean spray lance Spray gun with lock Click amp Clean Tornado PR nozzle Click amp Clean Powerspeed nozzle Click amp Clean foam sprayer Nozzle cleaning tool Trolley handle telescopic handle 13 Hose reel not standard 14 Hose hook 15 Model tag 16 Quick coupling 17 Button for telescopic handle 18 Turnable cable hook Specifications See model tag 15 of machine Sound pressure level meas ures in accordance with ISO 3744 EEC directive 2000 14 EEG La 69 9 dB A Lwa 84 dB A Hand arm vibrations measured according to ISO 5349 is lt 2 5 m s We reserve the right to alter the specifications 3 Before you start using your pressure washer 3 1 Mounting of trolley handle and hose hook standard models 3 2 Mounting of hose reel handle models with hose reel 1 Push down the trolley handle 12 over the two metal tubes Make sure that the handle is mounted as illustrated Mount screws with nuts make sure that the screws go through handle as well as tube 2 Mount the hose hook 14 on the machine 2 screws Note the hose hook can be mounted on the front as well as on the back Front position is to be used if the product is used together with a special wall hook for wall
5. appliances used electrical goods must be collected separately and recycled ecologically Contact your local authorities or your nearest dealer for further information e that only water without any impurities has been used e that the high pressure wash er has not been used for rental nor used commercially in any other way Repairs under this guarantee include replacement of defec tive parts exclusive of packing and postage carriage Besides we refer to your national law of sale The machine should be for warded to one of the service centres of the Nilfisk organisa tion with description specifica tion of the fault Repairs not covered by the guarantee conditions will be invoiced l e malfunctions due to Causes mentioned in section Troubleshooting Chart of the instruction manual 15 EN 9 3 Accessories Only use original accessories Click amp Clean Special nozzle for enameled surfaces Optimal distance 30 Car nozzle 50 cm Click amp Clean 90 angled special nozzle for undercarriage and wheel arches Undershassis Integrated guide shoes nozzle Click amp Clean Adjusted in angles from 0 90 for better working posture and Multiangle cleaning of hard to get at places as for instance barrels or the adaptor underside of the lawn mower Fits all nozzles Click amp Clean For cars and other surfaces Available in more shapes Brushes Extension hose 7 m extension hose increasing t
6. sure washer for the first time this instruction manual must be read through carefully Save the instructions for later USE Safety instructions marked with this symbol must be observed to pre vent danger to persons WARNING amp High pressure jets can be dangerous Never direct the water jet at persons pets live electrical equipment or the machine itself e Never try to clean clothes or footwear on yourself or other persons e Hold the spray lance firmly with both hands The spray lance is affected by a thrust of up to 16 4 N during ope ration e The operator and anyone in the immediate vicinity of the site of cleaning should take action to protect themselves from being struck by debris dislodged during operation Wear goggles during opera tion This symbol is used to mark safety instruc tions that must be observed to prevent damage to the machine and its performance This symbol indicates tips and instructions to simplify work and to ensure a safe operation e Never use the machine in an environment where there could be a danger of explo sion If any doubt arises please contact the local authorities e It is not allowed to clean asbestos containing surfaces with high pressure e This high pressure washer must not be used at tempe ratures below 0 C e Never let any persons stay under the product when stored on the wall WARNING Inadequate extension cables can be dangerous Ca
7. valve this water is not considered to be drinking water any more 2 Description 2 1 Application This high pressure washer has been developed for domestic use within Car motorbike boat cara van trailer patio drive flag stones woodwork brickwork barbecue garden furniture lawn mower Section 5 describes the use of the high pressure washer for vaious cleaning jobs IMPORTANT Only use wa ter without any impurities If there is a risk of running sands in the inlet water i e from your own well an additional filter should be mounted Repair and maintenance WARNING Always remove the electric plug from the socket be fore carrying out maintenance work on the machine Safety devices Locking device on spray gun 7a see foldout at the end of this manual The spray gun features a lock ing device When the pawl is activated the spray gun cannot be operated Thermal sensor A thermal sensor protects the motor against overloading The machine will restart after a few minutes when the thermal sen sor has cooled Pressure safety device An integrated hydraulic safety valve protects the system from excessive pressure Only use the high pressure washer for purposes described in this manual The safety precautions must be observed to prevent damage to the machine the surface to be cleaned or severe personal injuries 2 2 Operation elements and model survey N CONDO OF
8. will break down the plug and flush the dirt backwards pipes etc Rust paint Water sandblasting Mount the water sand blasting equipment and rust and paint equipment is efficiently and quickly removed Beware not to damage the surface to be sandblasted Green Tornado PR nozzle Wash with high pressure and maybe a brush You may use Stone house brush Stone amp amp Wood Cleaner to remove moss and algae Wood Cleaner Garden Tornado PR Rinse the worst dirt off with the nozzle Apply Metal Cleaner with tools nozzle Power the foam sprayer and let it act for approx 5 min Wash with the lawn speed nozzle nozzle You may use the multiangle adaptor for hard to get at mover multiangle adaptor areas to avoid splashing Metal Cleaner 11 6 1 Storing the washer 6 2 Winding up of electric cable and high pressure hose The machine should be sto red in a frost free room Pump hose and accessories should always be emptied of water prior to storing as follows h Stop the machine turn the start stop switch 1 to posi tion O and detach water hose and accessory 2 Restart the machine and activate the trigger Let the machine run until no more water runs through the spray gun To avoid accidents the electric cable and the high pressure hose should always be winded EN 6 After using your pressure washer 3 Stop the machine unplug and wind up hose and cable 4 Place spray handle nozzles
9. AN Nilfisk 130 2 Nilfisk 140 2 Nilfisk 145 2 ee HELLE LA LI LEN EN User Manual LL eS Copyright O 2011 Nilfisk Division of Nilfisk Advance A S Index 1 Safety precautions and warnings cccccceseeeeeeeeeeeeeeeeseeeeens 3 2 DBESCHID HON EE she rene EENE Da 4 3 Before you start using your pressure washer 5 4 Operating your pressure washer cccseeeecseeeeeceeeeeseeeeeneeees 6 5 Fields of Application and Working Method ccccccececceeeeeeeeeeseeeeeeeseeeeseeeesseeeees 10 6 After using your pressure WaSher rrnnrrnnnnnnnnnnnrennnnnennnnnnen 12 7 Maintenance vasse dieee dene hetaledisannsddes 13 ETE SON Gen 14 9 Further information 4 oseccencintdesecvasbaceidoepcanornacnanadecaceeadanesasenssess 15 10 EG Declaration of Gonormihunaammaanmnsmenmeavneinsisne 17 1 Safety Precautions and Warnings r Symbols used to mark in structions Do not let children or people who have not read the instruc tion manual operate the ma chine Before starting up your machine please check it carefully for any defects If you find any do not start up your machine and con tact your Nilfisk distributor Especially check e The insulation of the electric cable should be faultless and without any cracks If the electric cable is damaged an authorized Nilfisk distributor should replace it Before starting up your high pres
10. ake in water from a rain water tank as an example The hose for the wa ter Supply must not be too long approx 5m Make sure that the water tank is not placed on a lower level than the machine 1 Place the other end of the water hose in the water tank The machine features a tele scopic handle To raise or lower the handle press the knob and move the handle upwards or downwards When a click is heard the handle is in right position Do not cover the machine during operation Note If the ma I chine is left or not used for 5 minutes it must be switched off on the start stop switch O 1 1 Turn the start stop switch to position O 2 Disconnect the electrical plug from the socket 3 Shut off the water supply and activate the trigger to relieve the machine of pressure 4 Lock the spray gun When releasing the trigger of the spray gun the machine automatically stops The ma chine will start again when you re activate the spray gun Use an external filter if the water contains impurities 2 Turn the start stop switch to position I 3 Activate the trigger of the spray gun and let the water run until the air has escaped from the water hose and the pump 4 Mount spray lance and nozzle 4 7 Pressure regulation on the TORNADO PR nozzle High pressure Low pressure 4 8 Stationary use The pressure can be regulated on the TORNADO PR nozzle If mounting a speci
11. al wall hook not standard the pressure washer can be used as a sta tionary solution meaning that it can be operated while hanging on the wall Only mount the wall hook ona sturdy wall Adjust the length of the screws and size of rawl plugs to the type of wall On the wall hook garden rim brush a foam sprayer b Click amp Clean brush c and Click amp Clean nozzles d can be stored Important The bearing capacity of the wall hook is max 30 kg EN EN 5 Fields of application and working methods 5 1 General 5 1 1 Detergent and foam 5 1 2 Mechanical effect Efficient high presure cleaning is achieved by following a few guide lines combined with your own personal experience of specific cleaning tasks Accessories and detergents when correctly cho sen can increase the efficiency of your pressure washer Here is some basic information about cleaning Foam or detergent should be applied onto dry surfaces so that the chemical product is in direct contact with the dirt Detergents are applied from bottom to top for example on a car bodywork in order to avoid super clean areas where the detergent collects in higher concentration and streams downwards Let the detergent work for several minutes before rinsing but never let it dry on the surface be ing cleaned Note It is important that the detergents do not dry up Otherwise the surfac that has to be cleaned can be damaged In order to break down t
12. and wash with the rim brush For steel rims use Car Com atomizer bi Cleaner Use the foam sprayer and wash with rim brush Alu Cleaner Be careful The high pressure jet may damage the tyres Flag Powerspeed Wash towards outlets or the like On surfaces with moss or stones nozzle algae you may start by applying Stone amp Wood Cleaner with concrete Stone amp Wood the foam sprayer Wash before the soap dries Another floors and Cleaner more effective and quicker method is to use the Patio other hard Patio Cleaner Cleaner Thus you will also avoid splashes surfaces Garden Wood Cleaner Apply Wood Cleaner and wash before the soap dries furniture Garden brush NOTE Use the garden brush to clean off the dirt wood Brickwork Powerspeed Same method as for flagstones but be careful bad joints and Wood nozzle wood may be damaged by high pressure You may choose only work Stone amp Wood to use the Tornado nozzle Adjust the distance pressure to Cleaner the quality of the joints and the wood Patio Cleaner can also be Patio Cleaner used on vertical surfaces Gutter Underchassis spray Wash the gutter with the nozzle Always wash towards lance downpipes Beware not to spray under the roofing Cleaning Tube cleaner Push the tube cleaner approx 7 m to mark into a tube or drain of drain and activate the trigger of the spray handle The nozzle opening pipes out turning backwards will pull the cleaner through the tube The lets down nozzle
13. ations Applied harmonised standards Applied national standards and technical specifications frk f rer Anton S rensen General Manager Technical Operations EAPC EU Declaration of Conformity High Pressure Washer Nilfisk E 130 2 E 140 2 E 145 2 230 V 1 50 Hz IP X5 2006 42 EC 2006 95 EC 2004 108 EC EC Machine Directive EC Low voltage Directive EC EMV Directive EN 60335 2 79 IEC 60335 2 79 Nilfisk Division of Nilfisk Advance A S Industrivej 1 DK 9560 Hadsund Hadsund 01 10 2010 17 Nilfisk www nilfisk com
14. bles on drums should always be com pletely unwinded to prevent the cable from overheating Extension cables should be of a watertight construction and comply with the below men tioned requirements for length and cable dimensions 1 0mm2 max 12 5 m 1 5mm2 max 20m 2 5mm max 30 m e Cable connections should be kept dry and off the ground Mains power connection 0 The following should be ob served when connecting the high pressure washer to the electric installation amp Only connect the machine to an installation with earth con nection e The electric installation shall be made by a certified elec trician e It is strongly recommended that the electric supply to this machine should include a re sidual current device GFCI Water connection Connection to the public mains according to regu lations This high pres sure washer is only allowed to be connected with the drinking water mains when an appro priate backflow preventer has been installed Type BA accord ing to EN 1717 The backflow preventer can be ordered under number 106411177 The length of the hose between the back flow preventer and the high pressure washer must be at least 10 metres to absorb pos sible pressure peaks min diam eter inch Operation by suction for ex ample from a rainwater vessel is carried out without backflow preventer Recommended suc tion set 126411387 As soon as water has flown through the BA
15. e pawl to detach the Click amp Clean nozzle IMPORTANT Only use wa ter without any impurities If there is a risk of running sands in the inlet water i e from your own well an additional filter should be mounted 1 Let the water run through the water hose before connecting it to the machine to prevent sand and dirt from penetrat ing the machine Note Check IS that the filter is fitted in the water inlet pipe and that it is not clogged up 2 Connect the water hose to the water supply by means of the quick connector inlet water max pressure 10 bar max temperature 50 C 3 Turn on the water EN EN 4 4 Telescopic handle 4 5 Start and stop of the ma chine when connected to a water supply 4 6 Start the machine when connected to open con tainers suction mode The spray lance is affected by a thrust during opera tion therefore always hold it firmly with both hands IMPOR TANT Point the nozzle at the ground Check that the machine is in upright position NOTE Do not place the ma chine in high grass 2 Release the trigger lock 3 Activate the trigger of the spray gun and let the water run until all air has escaped from the water hose 4 Turn the start stop switch 1 to position I 5 Activate the trigger of the spray gun Always adjust the distance and thus the pressure of the nozzle to the surface which is to be cleaned The washer can t
16. he working range Underchassis Special spray lance for washing your car underneath spray lance Drain amp Tube 15 m long tube cleaner for the cleaning of tubes and drains cleaner Water sand For removal of paint and rust Sand available from do it your blasting equip self shops ment Patio Plus Equipment for quick cleaning of patio drive flagstones Garden brush Rotating brush for cleaning of wooden surfaces Rim brush Rotating brush for cleaning of wheel rims Wall hook For suspension of your high pressure washer on the wall Rotary brush For cleaning vehicles and other surfaces Water suction kit me For removal of large amounts of water from e g garden K CR W UR 7 Kors pounds 7 HV amp 16 Detergents Stone amp Wood Cleaner For flagstones brick and woodwork Suitable for moss and algae Plastic Cleaner For plastic and synthetic materials such as garden furniture Metal Cleaner For cleaning of metal such as garden tools Car Combi Cleaner For cars etc With rinsing wax Alu Cleaner For surfaces of aluminium Applied with an atomizer Oil amp Grease Cleaner For cleaning of grease and oil on motors for instance Applied with an atomizer Wood Cleaner For cleaning of wooden surfaces incl of wooden garden furniture 10 EU Declaration of Conformity C Product Type Description The design of the unit corresponds to the following pertinent regul
17. ough layers of dirt additional mechanical effect may be required Special wash brushes offer this supplemen tary effect that cuts through dirt especially by car washing 10 5 2 Typical fields of application Below you will find a description of a lot of cleaning tasks which can be solved by a pressure washer from Nilfisk in association with accessories and detergents Task Accessories Click Cleaning method amp Clear Car Car nozzle 1 Apply Car Combi Cleaner with the foam sprayer Always auto brush start from the bottom and work upwards Let Car Combi underchassis Cleaner act for at least 5 min nozzle 2 Wash the car with the car nozzle which has been optimized for Foam sprayer quick and gentle cleaning of enamelled surfaces the jet is wider Car Combi Cleaner and not so sharp Start at the front of the car and work back wards to avoid water from penetrating by the door mouldings 3 Use the brush for removal of traffic film which is not removed by the nozzle If the car is very dirty apply Car Combi Cleaner again 4 Attach the undercarriage nozzle and clean undercarriage and wheel arches 5 Remove water from the surface of the car with the scraper on the car brush Make sure that all grains of sand etc have been removed before using the scraper Wipe with a wash lea ther where the scraper cannot reach Rims alu Rim brush Apply Alu Cleaner with an automizer Let it act for approx minium auto nozzle 5 min
18. storage s k Click the hose reel handle on to the trolley handle no screws EN EN 3 3 Mounting of quick coupling 3 4 Mounting of high pressure hose 4 1 Connection of high pressure hose models without hose reel 1 Screw the quick coupling 16 tight on to the water inlet 2 Note The inlet filter must al ways be fitted in the water inlet pipe to filter out sand limestone and other impurities as these will damage the pump valves Caution Failure to fit the filter will invalidate the guarantee Attach the high pressure hose 4 to the spray gun 7 De h the high pressure hose by pressing the pawl A 1 Mount the high pressure hose on the outlet 3 4 2 Mounting of spray lance and Click amp Clean nozzles 1 Push the spray lance 6 into the spray gun 7 and screw it on 4 3 Water connection Note The spray lance 6 has a built in low pressure nozzle that can be used for flushing away dirt An ordinary 1 2 garden hose of min 10 m and max 25 m will be suitable NOTE Connec tion to the public mains according to regulations 2 Attach the nozzle Warning When attaching the Click amp Clean nozzles the pawl on the side of the spray lance should come out again Note The Tor I nado PR noz zle and the foam sprayer feature a swivel lock which must be positioned in the hole in the Click amp Clean spray lance Press th
19. use Machine not plugged in Defective socket Fuse has blown Defective extension cable Pump sucking air Valves dirty worn out or stuck Pump seals worn out Low voltage or low temperature Fuse has blown Incorrect mains voltage Thermal sensor activated Nozzle partially blocked Fuse too small Air in inlet hose pump Inadequate supply of mains water Nozzle partially blocked Water filter blocked Hose kinked Pump spray gun is leaking Pump hoses or accessory frozen No water supply Water filter blocked Nozzle blocked Recommended action Plug in machine Try another socket Replace fuse Switch off other machines Try without the extension cable Check that hoses and connections are air tight Clean and replace or refer to local Nilfisk distributor Clean and replace or refer to local Nilfisk distributor Activate the trigger of the spray gun Replace fuse Switch off other machines Check that the mains voltage corresponds to specification on the model tag Leave the washer for 5 minutes to cool down Clean the nozzle see section 7 2 Change to an installation higher than the amp consumption of the machine You may try without the extension cable Allow machine to run with open trigger until regular working pressure resumes Check that the water supply corresponds to specifications required see model tag NB Avoid using long thin hoses min 1 2 Clean the nozzle see section 7
Download Pdf Manuals
Related Search