Metra 99-7612B car kit
Contents
1. Figure F Right side Figure D y Memor d 99 7612 Dash Disassembly Remove the unified meter a c amp from radio chassis assembly Figure G Remove 8 Phillips screws securing the switch panel to the radio trim panel Unplug and keep the harness and trim panel for Kit Assembly Figure H Continue to kit assembly Figure H y Meer d Kit Assembly 99 7612 ISO DIN head unit provision with pocket 1 Trim the shaded areas from the factory radio trim panel Figure A Do not cut the locator and screw hole off as they will be necessary to mount the 99 7612 radio housing See detail 2 Attach the 99 7612 Radio Housing to the Radio Trim Panel using 4 supplied 3 8 Phillips screws Figure B 3 Mount the Radio Housing Brackets to the head unit with the screws supplied with the unit Figure C 4 Mount the pocket to the radio bracket assembly using 4 supplied 3 8 Phillips screws Figure C Figure C Figure A y Memor d Kit Assembly 99 7612 ISO DIN head unit provision with pocket 5 Mount the Unified Amp Meter to the radio bracket assembly using 2 supplied 3 8 Phillips screws Figure D 6 Plug the factory harness removed in disassembly into the 99 7612 7 Mount the whole radio pocket meter assembly to the radio trim panel using 4 supplied 3 8 Phillips screws Figure E 8 Locat2. Continued on next page y Meer d 99 7612 SWC Button Reassignment Remapping For instance the next command to be mapped is the Volume Down command Let s say you want the Mode button on your steering wheel to be the Volume Down command Hold down the Mode button till the LED lights up solid red and then release it Now your Mode button on the steering wheel is Volume Down 5 After the last button is programmed on your steering wheel you do not have to go through the whole list hold down the Volume Up button for at least 10 seconds then the led will go out Or After the 18th button is programmed or skipped the LED will go out and the remapping is completed y Menz INSTALLATION INSTRUCTIONS FOR PART 99 7612 REV 5 9 12 METRA THE WORLD S BEST KITS 800 221 0932 4 metraonline com COPYRIGHT 2004 2011 METRA ELECTRONICS CORPORATION
3. e the factory wiring harness and antenna plug in the dash Metra recommends using the proper mating adapters from Metra and or AXXESS Figure D 9 Follow the wiring instructions in this manual and reassemble dash in reverse order of disassembly Figure E y Menz Kit Assembly 99 7612 DDIN head unit provision 1 Trim the shaded areas from the factory radio trim panel Figure A Do not cut the locator and screw hole off as they will be necessary to mount the 99 7612 radio housing See detail 2 Attach the 99 7612 Radio Housing to the Radio Trim Panel using 4 supplied 3 8 Phillips screws Figure B 3 Slide the Double DIN head unit into the radio housing brackets and secure with screws supplied with the unit Figure C Figure C y Memor d Kit Assembly 99 7612 DDIN head unit provision 4 Mount the Unified Amp Meter to the radio bracket assembly using 2 supplied 3 8 Phillips screws Figure D 5 Plug the factory harness removed in disassembly into the 99 7612 6 Mount the whole DDIN radio meter assembly to the radio trim panel using 4 supplied 3 8 Phillips screws Figure E 7 Locate the factory wiring harness in the dash Metra recommends using the proper mating adapter from Metra or AXXESS Re connect the negative Figure D battery terminal and test the unit for proper ope
4. ing of the steering wheel controls process within the first 20 seconds of turning the ignition key on If you wait longer then the 20 seconds you will have to turn the ignition off then back on again e Within the first 20 seconds if any button other then Volume Up or Volume Down is pushed the remapping process will stop e f during the remapping process no button is pushed for 30 seconds the remapping process is aborted and the original settings are reset So let s begin the remapping process 1 Turning off the radio is recommended 2 Within the first 20 seconds of turning the ignition on press and hold down the Volume Up button for at least 25 seconds 3 The lights on the 99 7612 will light up solid Release Volume Up and the lights will go out Volume Up has now been programmed 4 Follow the list below in order however pushing the steering wheel control button you want for the function below If you want to skip a command press the Volume Up on the steering wheel this will tell the 99 7612 to skip the command and go to the next one 1 Volume Up 6 Mute 11 Play Enter 16 Fan Down 2 Volume Down 7 Preset Up 12 PTT Push To Talk 17 Temp Up 3 Seek Up Next 8 Preset Down 13 On Hook 18 Temp Down 4 Seek Down Prev 9 Power 14 Off Hook 5 Source Mode 10 Band 15 Fan Up Note Remember not all radios will have all these commands Please refer to the radios owners manual for specific commands recognized by the radio
5. ration 8 Follow the wiring instructions in this manual and reassemble dash in reverse order of disassembly Figure E y Meer d 99 7612 Wiring Instructions From the included 7612 harness 1 Plug the black 16 way connector into the 99 7612 2 Plug the black 12 way connector into the 99 7612 3 Plug the white 16 way connector into the factory harness Driver Information Center Button Control Note The metra kit button layout does not provide the MAINT or the E M buttons from the factory setup MAINT button on the 99 7612 is accessed by pressing the DAY NIGHT and HOUR buttons simultaneously The E M button is done by pressing PREV and MIN simultaneously SWC Instructions Plug the 3 5 jack into the aftermarket radio NOTE If using an Eclipse or Kenwood radio use supplied female 3 5 adaptor For Kenwood late model JVC radios e Connect the Kenwood SWC wire normally Blue Yellow to the Brown wire of the 3 5 jack Isolate and tape the Brown White wire it will not be used For Eclipse radios Connect the Eclipse SWC wires normally Brown and Brown Black to the Brown and Brown White wires of the 3 5 jack Brown goes to Brown and Brown White goes to Brown Black Other model radios connect key one to Brown and key two is not used y Meer d 99 7612 Wiring Instructions SWC Programming After all connections are made turn ignition and the 7612 buttons will flash the number of times that cor
6. respond with the radio installed See list below After the LED goes out test SWC functions Force mapping a radio type Programming must take place within 20 seconds of turning the ignition on 1 Hold the Volume Down button on the steering wheel for at least 25 seconds until the lights on the kit start to flash 2 Tap volume up to program the radio type Note Lights on kit will blink to corresponding number of button presses Use the following chart to choose which type of radio you are programming 1st LED flash is for Eclipse 2nd LED flash is for Kenwood 3rd LED flash is for Clarion 4th LED flash is for Sony and Dual 5th LED flash is for JVC 6th LED flash is for Pioneer and Jensen 7th LED flash is for Alpine 8th LED flash is for Visteon 9th LED flash is for Valor 10th LED flash is for Clarion 5V 11th LED flash is for Metra OE 3 Once you choose your radio type hold volume down for 5 seconds to finish programming the steering wheel controls Note The kit will confirm the radio type by the number of times the lights blink y Meer d 99 7612 SWC Button Reassignment Remapping Let s say you have the 99 7612 programmed to your vehicle and your radio and you want to change the button assignment for the steering wheel controls For instance you would like Seek Up to be Mute e The 99 7612 must have detected the vehicle and radio it is attached to before you can remap any buttons e You can only start the remapp
7. sories switches and especially air bag indicator lights must be plugged in before reconnecting the battery or cycling the ignition NOTE Refer also to the instructions included with the aftermarket radio eA KNOWLEDGE IS POWER gt e Enhance your installation and fabrication skills by 2 enrolling in the most recognized and respected mobile electronics school in our industry Log onto www installerinstitute com or call L 800 354 6782 for more information and take steps e o toward a better tomorrow rit Metra recommends MECP certified technicians y Memor d 99 7612 Dash Disassembly 1 Unclip and remove the trim panel surrounding the display and including the a c vents Figure A 2 Remove 2 Phillips screws exposed behind vent display trim panel Figure B 3 Unclip and remove the lower trim panel around the bottom of the radio panel Figure C Continued on next page Figure C y Memor d 99 7612 Dash Disassembly 4 Remove 1 Phillips screw per side of radio chassis exposed behind lower trim panel Figure D 5 Remove radio climate control assembly from the sub dash 6 Remove 4 Phillips screws securing the radio chassis to the factory radio trim panel Lift up slightly and proceed to step 7 Figure E 7 Unlock the connector on the switch panel and remove the cable joining the chassis and switch panel Figure F Continued on next page
8. y Meer d INSTALLATION INSTRUCTIONS FOR PART 99 7612 APPLICATIONS Nissan Murano 2003 2007 99 7612A 99 7612B KIT FEATURES e DDIN Head unit provisions e ISO DIN Head unit provision with pocket 7612A Coated with Brushed Aluminum look e 7612B Painted Matte Black KIT COMPONENTS e A Radio Housing e B Radio Housing Brackets e C Pocket e D 14 8 x 3 8 Phillips screws e E 2 8 x 1 2 Phillips screws e F 7612 wire harness G Female 3 5mm Connector w Brown and Brown White Wires TATTOO WIRING 8 ANTENNA CONNECTIONS Sold Separately Wiring Harness e 70 7550 1995 Up Nissan Harness e 70 7551 1995 Up Nissan Amp Integration Harness Antenna Adapter e 40 NI10 Nissan Antenna Adapter TOOLS REQUIRED Panel Removal Tool e Phillips Screwdriver e Socket Wrench METRA THE WORLD S BEST KITS 800 221 0932 4 metraonline com REV 5 9 12 COPYRIGHT 2004 2011 METRA ELECTRONICS CORPORATION y Memor d 99 7612 Table of Contents Dash Disassembly Nissan Murano 2003 2007 sis Vrbe aaa 3 5 Kit Assembly ISO DIN head unit provision with pocket 6 7 DDIN head unit provision an en ed qua XAR Era e PST ra ERES FEE Pads 8 9 SWC Instructions Wiring instructions irc iaa 10 11 SWC button reassignment remapping 12 13 Caution Metra recommends disconnecting the negative battery terminal before beginning any installation All acces
Download Pdf Manuals
Related Search