Gefen DVI-32432 video switch
Contents
1. display telnet welcome 0 Telnet welcome at login is set to OFF display telnet welcome 1 Telnet welcome at login is set to ON 37 865 232 TELNET COMMANDS ipconfig Command Prints the current IP configuration on the screen syntax ipconfig Parameters None Example ipconfig xc EE TCP IP Settings eeeeeescecces MAC add 00 1C 91 02 80 18 IP add 192 168 2 238 Net Mask 255 255 255 0 Gateway 192 168 2 1 Web Server Port 80 Telnet Server Port 23 Telnet password at login is set to OFF Telnet welcome at login is set to OFF 38 885 232 TELNET COMMANDS resetip Command The resetip command resets the IP configuration to the factory default setting Syntax resetip Parameters None Notes The default IP address is 192 168 1 75 The default IP gateway is 192 168 1 254 The matrix must be rebooted after executing this command Example resetip Reset ip configuration to factory default ipconfig e TCP IP settings e MAC add 00 1C 91 02 80 18 IP add 192 168 1 75 Net Mask 255 255 255 0 Gateway 192 168 1 254 Web Server Port 80 Telnet Server Port 23 Telnet password at login is set to OFF Telnet welcome at login is set to OFF 39 RS 232 TELNET COMMANDS http port Command Specifies a new port The underscore character must be included w2. 1080 el wexse DVI Matrix GEF DVI 3eua3e User Manual wwWw gefenpro com ASKING FOR ASSISTANCE Technical Support Telephone 818 772 9100 800 545 6900 Fax 818 772 9120 Technical Support Hours 8 00 AM to 5 00 PM Monday through Friday Pacific Time For 24 7 support see the back of the product for the support number Write To Gefen LLC c o Customer Service 20600 Nordhoff St Chatsworth CA 91311 www gefenpro com support gefenpro com Notice Gefen LLC reserves the right to make changes in the hardware packaging and any accompanying documentation without prior written notice 32x32 DVI Matrix is a trademark of Gefen LLC 2012 Gefen LLC All rights reserved All trademarks are the property of their respective owners Rev AS O gt 0 1 40 0 0102 0 S N ND NS gt gt gt gt O Q AN O O OO O Q O OQ1 OO gt gt O Introduction Operation Notes Features Front Panel Layout Front Panel Descriptions Back Panel Layout Back Panel Descriptions CONTENTS Connecting the 32x32 DVI Matrix Wiring Diagram Operating the 32x32 DVI Matrix Main Display Displaying Additional Information Displaying the Current Routing State Mode Buttons Routing Sources System Lock Mode Cancelling a Function Cycling between Information Screens Saving the current Routing State Recalling a sto
3. 9 to specify individual local inputs which will receive the default EDID If more than eight inputs need to be specified then edidbatolo command must be executed twice Examples ediddetolo 2 3 4 5 6 7 8 9 Loading default EDID to locals please wait Finished Loading ediddetolo 0 Loading default EDID to all locals EDID please wait Finished Loading 29 385 232 TELNET COMMANDS ediddstoba Command The ediddstoba command reads the downstream EDID and stores it to a specified EDID bank Syntax ediddstoba paraml param2 Parameters 1 downstream display 1 32 param2 EDID bank offset 1 20 Example ediddstoba 1 2 Loading Output 1 EDID to EDID bank 2 please wait Finished Loading 30 865 232 TELNET COMMANDS ediddstolo Command The ediddstolo command reads the downstream EDID and stores it to a local input Syntax ediddstolo paraml param2 param9 Parameters 1 downstream display 1 32 param2 param9 Input list 1 32 Notes If param2 0 then the downstream is stored in all 32 DVI inputs If more than eight inputs need to be specified in order to receive the downstream EDID the edidsdtolo command must be executed twice Examples ediddstolo 1 3 8 9 10 Loading Output 1 EDID to locals EDID please wait Finished Loading ediddstolo 1 0 Loading Output 1 EDID to all locals EDID please wait
4. Finished Loading 31 865 232 TELNET COMMANDS lock_edid Command The lock_edid command enables disables the loading of EDID on each input during a power cycle Syntax lock edid paraml Parameters 1 EDID lock state 0 1 0 lock edid 1 Enable lock EDID mode lock edid 0 Disable lock EDID mode 32 RS 232 TELNET COMMANDS prbaedid Command The Zprbaedid command reads the EDID file from the specified bank Syntax prbaedid Parameters param 1 Example prbaedid 0x00 0 4 0 34 OxOA OxOF 0x81 0x95 0x80 0x45 0x66 0x40 0x00 0x4B 0x20 0x00 OxOA 0x02 0x03 0x01 0x03 0x37 0x20 0x00 0 1 OxSA Ox8A 0 2 0x13 0 50 0 00 OxOF 0x18 0x00 0 21 0 70 0 1 0 20 0x53 0x20 0x03 0x20 0x00 0x01 0x2D 0x01 0 6 0 00 0 16 0 00 0 20 0 01 0 91 0 54 0 81 OxB3 0x71 0 50 0 36 0 00 0x51 0x20 0x41 0x20 0x29 0x22 0x00 0 6 0 20 0 1 0 28 OxlE 0x20 0x00 OxEO 0x00 0x00 0 06 0 03 OxBD 0 40 0 00 0 38 Ox5A 0 00 0 00 0 17 0 20 0 4 0 20 x23 xE2 0x03 OxDO 0x00 0x55 0x01 0x58 0x00 0x2D 0x00 0x00 Bank OxFF 0x01 0x80 0x54 OxEF 0x81 OxA9 0 2 0 00 0x51 OxAO 0x00 0x00 0x00 0x53 0x20 0x46 0x09 0x00
5. m The front panel LCD will display the following 2 Press any Input button s A1 D8 to select the EDID data destination s 4 4 4 4 4 4 4 24 MODE BUTTONS 3 Press the Set button to copy the default EDID to the selected Input Press the Set button T The front panel LCD will indicate that the EDID is being copied After a few moments front panel LCD will indicate that the EDID copy process was completed 25 5 232 e 9876 Only Pins 2 RX 3 TX and 5 Ground are used on the RS 232 serial interface RS232 Settings Pil pero T 19200 5 9 Es LOU T 1 CONGO RR IMPORTANT When sending RS 232 commands a carriage return and a line feed character must be included at the end of each line Telnet Command Names are case sensitive NOTE The return value will be displayed when using a terminal based application indicating the current value after executing the command 26 IP CONFIGURATION Configuring the IP Address The 32x32 DVI Matrix supports IP based control using Telnet or the built in Web based GUI To set up IP control the network settings for the 32x32
6. param9 Parameters None Notes Unlike other commands do not precede the command with the symbol If param2 0 then the specified input will be routed to all outputs also refer to s com mand on the next page If more than eight inputs need to be specified then the com mand must be executed twice Examples r 12 Input 1 is routed to outputs 2 Routing Input 1 to Output 2 r 14 5 6 7 9 l0 Input 1 is routed to outputs 4 5 67 9 10 Routing Input 1 to Output 4 Routing Input 1 to Output 5 Routing Input 1 to Output 6 Routing Input 1 to Output 7 Routing Input 1 to Output 9 Routing Input 1 to Output 10 rf d O All outputs are routed to input 1 Routing Input 1 to 11 Outputs 54 RS 232 TELNET COMMANDS s Command The s command routes the specified input to the designated output s Syntax S paraml Parameters None Notes Unlike other commands do not precede the s command with the symbol If param1 O then all inputs will be routed to their respective outputs e g 1 1 2 2 3 3 4 4 5 5 Examples S 5 Routing Input 5 to all Outputs s 0 Routing 11 2223 55 activebolo fadefault help lock_fo reboot set_input_name set_output_name show_temp RS 232 TELNET COMMANDS System Activates the boot loader Resets the matrix to factory default settings Displays the list of available commands
7. Syntax This command will be available in a future release Parameters This command will be available in a future release 57 865 232 TELNET COMMANDS help Command The help command displays help on the specified command Syntax help Parameters 1 Command optional Notes If param7 is not included then the full list of commands is displayed Example ediddetolo Store the default Internal EDID to local inputs EDID Syntax ediddetolo paraml param8 Paraml 0 All inputs Paraml Param8 1 32 Input list e g ediddetolo 5 6 7 58 865 232 TELNET COMMANDS lock_fo Command The lock_fo command locks unlocks the 5V power lock state Enabling this feature will store the 5V status for each input prior to shutting the unit down This preserves the 5V state when the unit is restarted Enabling this feature should be used when attaching fiber optic extenders to the outputs on the matrix Syntax lock lo paraml Parameters param1 State O 1 CENE Disable Power Lock Enable Power Lock Example lock lo 1 Enable lock Power mode lock lo 0 Disable lock Power mode 59 RS 232 TELNET COMMANDS reboot Command The reboot command reboots the 32x32 DVI Matrix The parameter 10 must be included as part of the command Unlike RS 232 if the reboot command is entered via Telnet the Telnet connection will be lost and will need t
8. To activate other board boot loader please type the command again without any parameter Type the command activebolo 2 This will load the Back Panel FW into the Memory The unit will exit the boot loader screen and return to the standard Hyperterminal window Note If there is any Board Failure message appears at this stage please ignore it Repeat steps 3 12 for the file MMTX DVIinout e 0 1 17 bin 89 24 25 26 27 28 29 30 FIRMWARE UPDATE message will appear in Hyperterminal Download Completed Successfully Name MMTX BP e 0 2 26 bin Size 47536 Bytes Saved new version on Programs memory Activate Boot loader from application again with parameters activebolo 5 The unit will exit the boot loader screen and return to the standard Hyperterminal window Type the command activebolo Following text should appear on terminal screen The System detect FW on memory DVI8 IN OUT boards To activate this board boot loader please type the command again with the parameter 5 To activate other board boot loader please type the command again without any parameter Type the command activebolo 5 Following text will appear on the terminal window Forced boot loader activation for DVI8 IN OUT boards Please This will load the Input and Output boards FW into the Memory This process may take a few minutes to complete 90 RACK MOUNT SAFETY INFORMATION Maximum re
9. Used for routing an Input to an Output Each of these buttons represents an Input See page 11 for more information on routing sources BACK PANEL LAYOUT Back Panel BACK PANEL DESCRIPTIONS Back Panel Out 1 32 Connect DVI displays to these ports In 1 32 Connect computers or other DVI source devices to these ports RS 232 Serial Port Connects to the RS 232 control device The 32x32 DVI Matrix may be switched remotely using this port See page 26 for more information Telnet Control Connect the 32x32 DVI Matrix to a network in order to use IP Telnet control IR Connect an IR extender to this IR port Power This LED indicator glows bright red when the matrix is powered on Power Supply 1 2 Connect the included AC power cords from these receptacle to an available electrical outlet The redundant secondary power cable should be connected to an electrical outlet on a different circuit Each power supply is 110 220V AC CONNECTING THE 32X32 DVI MATRIX How to Connect the 32x32 DVI Matrix 1 Connect up to 32 DVI source devices to the DVI inputs on the rear panel of the 32x32 DVI Matrix using DVI cables 2 Connect up to 32 DVI displays to the DVI outputs on the rear panel of the 32x32 DVI Matrix 3 Connect the included power cord to the power input receptacle on the rear panel of the 32x32 DVI Matrix Connect the opposite end of the cable into a open wall power socket Wi
10. A0A0A0A0A0A0A20A2020202020A20A20A20A0 32 51 RS 232 TELNET COMMANDS savepreset Command The savepreset command saves the current routing and masking state to the specified memory preset Syntax Savepreset paraml Parameters param1 Routing preset 1 16 Notes If param2 0 all outputs will be masked If more than eight inputs need to be specified then the maskout command must be executed twice Example 2 Saved current set 2 52 RS 232 TELNET COMMANDS m Command The m command displays the routing status table Syntax m Parameters None Notes Unlike other commands do not precede the m command with the symbol Example m Routing status table Outputs 0 1 2 3 4 5 6 7 1 1 2 3 4 5 6 7 8 9 9 10 11 12 13 14 15 16 17 17 18 19 20 21 22 23 24 23 25 26 27 28 29 30 31 32 Masking status table Outputs 0 1 2 3 4 T5 6 7 1 A A A A A M M M 9 A A A A A A A A 17 A A A A A A A A 25 A A A A A A A A Monitor HPD status table Outputs 0 1 2 3 4 5 6 7 1 H L L L L L L L 9 L L L L L L L L 17 L L L L L L L L 25 L L L L L L L L 53 RS 232 TELNET COMMANDS Command The r command routes the specified input to the designated output s Syntax paraml
11. 0x0C 0x04 0 72 0 00 Ox1D 2 9 0 10 0 00 0 00 0 00 0 66 0 4 0 80 0 80 0 40 0 40 0 00 0 00 0 5 OxFD OxOA 0x00 0 55 0 20 0 90 0 07 OxOF 0x00 0 01 0 51 OxAO 0x80 0x25 0x8C 0x10 0x00 0x00 0 00 0 39 0 99 71 0 95 0 02 0x58 0x00 0x1B 0x00 0x00 0x20 0x00 0 4 0 01 0 04 0 07 OxE3 0 20 0 40 OxDO 0 5 0 18 0 00 OxOA x3E 0x00 0x00 33 0x00 0x00 0x78 0x26 4 0 00 2 0 30 0 00 0 18 0x20 0x47 0x59 0x05 0x83 0x05 0x00 0x00 0 00 0 71 OxDO 0x96 0 00 0 65 1 20 385 232 TELNET COMMANDS prdsedid Command The prdsedid command displays the specified downstream EDID Syntax prdsedid paraml COMMAND DOES NOT WORK PROPERLY Parameters param1 A downstream display 1 32 Example prdsedid 1 Read Output EDID 1 please wait 0 00 OxFF OxFF OxFF OxFF OxFF OxFF 0x00 0 4 Ox2D OxAC 0x06 0x01 0x00 0x00 0x00 0x34 0x13 0x01 0x03 0x80 0x66 0x39 0x78 OxEE 0x91 0x54 0 4 0x99 0x26 OxOF 0x50 0x54 OxBD OxEF 0x80 0x71 0 4 0x81 0x00 0x81 0x40 0x81 0x80 0x95 0x00 0x95 0 0 OxB3 0x00 9 0x40 0x02 0 3 0x80 0x18 0x71 0x38 Ox2D 0x40 0x58 0 2 0x45 0 00 0 5 0x00 0x00 0x00 0 1 0x66 0x21 0x50 0x51 0x00 0x30 0x40 0x70 0x36 0x00 0 0 5
12. 69 WEB INTERFACE Legend Provides color coded information on the status of each Input and Output PRG 32x32 Modular Matrix Routing Status Manag EDID Configuration Log Out Routing Preset Names VO Names 5V Output Masks 525 9999999999595999995999598 mw Pt 26 ot 26 27 27 28 28 26 29 29 Eo 30 31 31 on 31 32 32 32 Choci Save Routing Preset 1 Preset_l Save Recall Routing Preset 1 Preset 1 Save Routing Preset Saves the current routing state to memory Click the drop down list to select the desired routing preset then click the Save button to save the preset to memory 7 Recall Routing Preset Loads the selected routing state into memory Click the drop down list to select the desired routing preset then click the Recall button to load the preset into memory 70 WEB INTERFACE Routing gt gt Preset Names Refresh Updates the Web page to reflect the new Preset Name 32x32 Modular Matrix Status Manage EDID Configuration Preset Cancel Preset Preset 3 Preset 4 Preset 5 Preset 6 Name Type the desired name of the Preset in this field Click the Save Changes button to save the Preset Name Click the Cancel button to restore the previous name Save Changes Cancel Saves the current c
13. Standby Mode to cycle through each of the information screens Press the Cancel button 15 1 MODE BUTTONS Saving the current Routing State Set the routing state see page 11 then press the PreSet button twice to activate Preset Mode Press the PreSet button twice After pressing the PreSet button once the following will be displayed on the front panel LCD screen Press the PreSet button again The following will be displayed on the front panel LCD screen 16 MODE BUTTONS 2 Press an Input button D8 to store the current routing state BERR EEE D D D T ERE EE Bs 4 3 Press the Set button to complete the operation The system will remain in Save Current Preset Mode Press the Set button HR The front panel LCD screen will indicate that the current routing state has been saved 17 MODE BUTTONS Recalling a stored Routing State 1 Press the PreSet button once to activate Recall Preset Mode Press button once The following will be displayed on the front panel LCD screen 2 Press the Input button A1 D8 of the routing state to be recalled 18 MODE BUTTONS 3 Press the Set button to complete the operation The system will remain in Save Current Preset Mode Press the Set button i 4 The front panel LCD screen will indicate that the current routing state has
14. port The MAC address cannot be changed Click the Save Settings button to apply changes Click the Set Defaults button to restore the factory default IP settings The 32x32 DVI Matrix must be rebooted for any changes to take effect MAC Address 00 1 91 02 80 28 IP Address 192 168 1 205 I Subnet Gateway HTTP Port TGP Telnet Terminal Port UDP Port 32x32 Modular HTTP Port Administrator New Password Confirm New Password Username Old Password SYSTEM CONFIGURATION onfiguration Download 83 WEB INTERFACE TCP Telnet Terminal LOGIN SETTINGS Sets the user name and password for Telnet sessions to the 32x32 DVI Matrix Click the Save Settings button to apply changes Click the Force Password on Connect check box to have the 32x32 DVI Matrix prompt for a password each time a Telnet session is started User Name Administrator Old Password New Password Contin New Password Force Password on Gonnect Remote UDP IP Address 192 168 2206 Remote UDP Port 50021 Enable UDP Access Save Settings UDP Connection SETTINGS Sets the remote UDP IP Address and Port Click the Save Settings button to apply changes Click the Enable UDP Access check box to 84 WEB INTERFACE WEB LOGIN SETTINGS Sets the user name and password for Web Interface sessions
15. 0x00 0x00 0x00 0x1E 0x00 0x00 0x00 OxFD 0x00 0x18 0x4B 0 1 0x51 0x17 0x00 Ox0A 0x20 0x20 0x20 0x20 0x20 0x20 0x00 0x00 0x00 OxFC 0x00 0x53 0x41 0x4D 0x53 0x55 0x4E 0x47 0 0 0x20 0x20 0x20 0x20 0x20 0x01 0x59 0x02 0x03 0x29 0 1 0x46 0x90 0x04 0x05 0x03 0x20 0x22 0x23 0x09 0x07 0x07 0x83 0x01 0x00 0x00 0xE2 0x00 OxOF 0xE3 0x05 0x03 0x01 0x6E 0x03 0x0C 0x00 0x20 0x00 OxB8 0x2D 0x20 OxDO 0x04 0x01 0x40 0x00 0x37 0x01 OxlD 0x00 0x72 0x51 0xD0 0x1E 0x20 Ox6E 0x28 0x55 0x00 OxAO 0x5A 0x00 0x00 0x00 0x1E 0x01 0x1D 0x80 0x18 0x71 0 1 0x16 0x20 0x58 0 2 0x25 0x00 0 0 0 5 0x00 0x00 0x00 Ox9E Ox8C OxOA OxDO 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0 00 0x00 0x00 0x00 0x00 0x00 0x00 0x65 34 RS 232 TELNET COMMANDS predidst Command The predidst command prints a table that contains details relating to the Local EDID source and the display name Syntax predidst Parameters None Example predidst Input Source ID Monitor name 1 1 SAM SAMSUNG 2 1 SAM SAMSUNG 3 1 SNY SONY 4 1 SNY SONY 5 1 SAM SAMSUNG 6 1 SAM SAMSUNG 7 1 SAM SAMSUNG 8 1 NEC NEC 10 1 SAM SAMSUNG 11 1 SAM SAMSUNG 12 1 SAM SAMSUNG 13 1 SAM SAMSUNG 14 1 SAM SAMSUNG 15 1 SAM SAMSUNG 30 1 SAM SAMSUNG 31 1 SAM SAMSUNG 32 1 SAMSUNG 35 RS 232 TELNET COMMANDS Zprloedid Command The prloedid command reads the local EDID of a specified input and spools it to the
16. 98 Output 10 Output 11 Output 12 Output 13 Output 14 VO Names 45V Output Masks DVI OUT put 23 put 25 put 20 OUT rm m mi i l j a Type Displays the type of output card used in slot This matrix can only accept DVI outputs Output Click to place a check mark in the box and select the desired output Multiple outputs can be selected at a time Name Displays the current name of the output The name of each output can be changed See page 62 for details Check All Places a check mark in each box under the Output column Clear All Clears all check marks from the Output column 68 WEB INTERFACE INPUTS Provides information on each Input on the matrix 32x32 Matrix Input 1 6 Input 2 0 Input 4 Input 5 0 Input 6 Input 7 Input 8 Input 9 E moestaes O sv co c RM Input 10 Click this button to route Input 11 the current input and output Input 12 selection s a Input 13 Name Displays the current name of the input The name of each input can be changed See page 61 for details Input Click the radio button next to the desired input to be routed Only one input can be selected at a time Type Displays the type of input card used in slot This matrix can only accept inputs
17. DVI Matrix must be configured via RS 232 The default network settings for the matrix are as follows IP Address 192 168 1 72 Subnet 255 255 255 0 Gateway 192 168 1 254 HTTP Port 80 Telnet Port 23 1 Connect an RS 232 cable from PC to 32x32 DVI Matrix 2 Launch a terminal emulation program e g HyperTerminal and use the following settings Baud Rate 19200 Data Bits 8 Parity None Stop Bits 1 Flow Control None eo NOTE Depending upon the network the IP address subnet mask gateway IP Telnet port and HTTP port will need to be set Consult your network administrator to obtain the proper settings 3 IP address for the matrix using the sipadd command see page 45 for details 4 Set the subnet mask using the snetmask command see page 46 for details 5 Setthe gateway router IP address using the sgateway command see page 43 for details 6 Setthe Telnet listening port using the set telnet port command see page 42 for details 7 Setthe HTTP listening port using the set http port command see page 40 for details 8 Power cycle the matrix to reboot and complete all IP setting changes 9 Type the IP address that was specified in step 3 in a web browser to access the Web GUI or use the same IP address to Telnet to the matrix 27 RS 232 TELNET COMMANDS edidbatolo Read downstream EDID and stores in any Local Input ediddet
18. F OFF OFF OFF OFF OFF OFF OFF 3 OFF OFF OFF OFF OFF OFF OFF OFF 4 OFF OFF OFF OFF OFF OFF OFF OFF 66 WEB INTERFACE Using the Built in Web server The Web GUI is divided into four main pages Routing Status Manage EDID and Configuration Each of these pages is represented by a tab Click on the desired tab to open the its page Each page also has it s own set of tabs which can be accessed When the Web GUI is opened the Routing page tab will be displayed Routing gt gt Routing Tabs Click a tab to open the desired page Status Manage EDID Configuratii Preset Names Names 5V 32x32 Modular Matrix outin Status Manage EDID Configuration Routin Preset Names Names 5V Output Masks 100 10 LOCK Matrix Locks unlocks the matrix When the Matrix is locked no modifications can be made using the Web GUI Output The number of the output The blue highlight indicates that the output has been masked See page 75 for more information on masking outputs Input Displays the input that has been routed to the output In the illustration above Input 22 has been routed to Output 1 HPD Indicates the Hot Plug Detect HPD status of the input 67 WEB INTERFACE OUTPUTS Provides information on each Output on the matrix Manage EDID Configuration e Es Output 1 Output 2 Output 3 Output 4 Output 5 Output 6 Output 7 Output 8 Output
19. URES Features Combine 32 cross platform computers and 32 digital displays Supports resolutions up to 1080p Full HD and 1920 x 1200 Advanced EDID management permits upload of custom settings RS 232 Serial interface for remote control via a computer or control automation systems LCD status window Front panel push buttons for local switching IP Telnet Control with built in Web server Routing states can be stored and recalled at the touch of a button Built in dual redundant hot swappable power supplies Output masking command Standby mode Grounding screw Fan module optional Filter module optional Power ON OFF switch Supports DDWG standards for DVI Rack mountable Package Includes 1 GefenPRO 32x32 DVI Matrix 2 AC power cords 1 Quick Start Guide FRONT PANEL LAYOUT Front Panel H33439 FRONT PANEL DESCRIPTIONS Front Panel Mode Buttons These buttons are used to control other features on the product See pages 11 25 for more information Output Buttons 1 32 Used for routing an Input to an Output Each of these buttons represents an Output See page 11 for more information on routing sources Power Indicator This LED indicator will glow red when the power is turned on LCD Display Displays the current routing status of the Matrix and is also used to manage source routing Input Buttons 1 32
20. URPOSE ARE DISCLAIMED IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT INDIRECT INCIDENTAL SPECIAL EXEMPLARY OR CONSEQUENTIAL DAMAGES INCLUDING BUT NOT LIMITED TO PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES LOSS OF USE DATA OR PROFITS OR BUSINESS INTERRUPTION HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY WHETHER IN STRICT LIABILITY OR TORT INCLUDING NEGLIGENCE OR OTHERWISE ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE 94 MA GETF DbDVI 2324 58 1 800 545 6900 20600 Nordhoff St Chatsworth CA 91311 818 772 9100 www gefenpro com support gefenpro com E Rev fax 818 772 9120
21. ages of each input and output board inside the matrix Syntax show temp Parameters None Example show voltage ADC UI measurment result CORE 1 8 Value 1848 mVolt 501 DS460 501 PSOK Value 3061 mVolt 501 Imon Value 258 mV gt 2 Power result mV for all boards Power result mV for BP board 5v 3 3V 1 2V 1 2V 5038133301121311218 Power result mV for Inputs board 3 3 5 1 2 3 3 1 6 1 5070 33081 1805 2 5126 3336 1814 3 5114 3302 11801 4 5128 334611815 Power result mV for Outputs board Board 1 5 1 8 1 5076 331411803 2 5106 3268 1797 3 5064 3354 1795 4 5070 334611806 65 RS 232 TELNET COMMANDS f Command The f command enables disables 5V on the input The f command can also be used without parameters to return the state of each input ON is returned if 5V is enabled on the DVI input OFF is returned if 5V is disabled on the DVI input Syntax f paraml param2 Parameters param1 Input 1 32 param2 State 0 1 Mes O Notes The f command can also be used without parameters to return the state of each input is returned if 5V is enabled the DVI input OFF is returned if 5V is disabled on the DVI input Examples Turn on input 5 FO inputs status table Board 0 1 2 3 4 5 6 7 1 OFF OFF OFF OFF OFF OFF OFF OFF 2 OF
22. ank Bank 2 Ba nk 3 Bank 4 Bank 5 Bank 6 Bank 7 Bank 8 Bank 9 Save Changes c 03 amp Bank Indicates the EDID bank number Name Type the desired name of the EDID bank in this field Click the Save Changes button to save the bank name Click the Cancel button to restore the previous name Save Changes Save Changes Cancel Saves the current name Restores the previous names for each EDID change to the EDID bank s bank if a change was made 81 WEB INTERFACE Manage EDID gt gt Upload Download 32x32 Modular Matrix select EDID File to Upload Select Bank Location Select Bank Upload Browse Click this button to upload the EDID Click this button to to the specified bank select the EDID file to be uploaded Select Bank Location Click this drop down list to select the bank list to where the EDID will be uploaded Click this box to select the EDID that is to be saved Options to a file The EDID file will Bank_1 Bank_20 be saved in binary format bin Options Download Click this button to download the selected EDID to a file 1 Bank_ 20 Output 1 Output 32 Input 1 Input 32 82 WEB INTERFACE Configuration CHANGE IP SETTINGS Assigns address subnet gateway HTTP listening port and Telnet
23. been recalled 19 MODE BUTTONS Masking Outputs Masking prevents the output device display etc from receiving an output signal instead of powering down the output device The masking process is identical for masking or unmasking outputs 1 Press the Mask button to activate Mask Mode Press the Mask button The front panel LCD screen will indicate that the 32x32 DVI Matrix is in Mask Mode 20 MODE BUTTONS 2 Select the Output A1 D8 to be masked 2 11 11111111111114 1 k 4 ssi 4 3 Press the Set button to complete the operation Press the Set button B The front panel LCD screen will indicate that the selected output has been masked 21 MODE BUTTONS EDID Management Saving the Downstream EDID data to Local memory 1 Press EDID button once to activate DSTOLO Downstream Local Mode Press the EDID button once The front panel LCD display will show the following 2 Press any Output button A1 D8 to select the EDID data source MODE BUTTONS 3 Press any Input button A1 D8 to select the EDID data destination 4 Press the Set button to complete the operation Press the Set button i 23 in 2 OR 2 23 MODE BUTTONS Saving the Default EDID data to Local memory 1 Press the EDID button twice to activate DETOLO Default To Local Mode Press the EDID button twice
24. commended ambient temperature 45 104 Increase the air flow as needed to maintain the recommended temperature inside the rack Do not exceed maximum weight loads for the rack Install heavier equipment in the lower part of the rack to maintain stability Connect a bonding wire between an approved safety ground and the grounding screw on the chassis 91 SPECIFICATIONS Maximum Pixel u m 165 2 Vi ausos 1 2 Volts Video Input Connectors 32 DVI I 29 pin female digital only Video Output Connectors 32 DVI I 29 pin female digital only II o up d 3 5 mm mini stereo Ethernet IP control port RJ 45 jack 100BaseT USB firmware 55 232 Inter Tel OB sucus biens iaptnttntus DB 9 serial female Power SUP DIES NR 2 100 240V AC hot swappable Power 028 120 Fack mountabl uu u L 60 rack space rack ears included Dimensions W x H x D a 17 25 x 10 5 x 12 438mm x 267mm 305mm 20811886 u
25. ct or omission in this manual even if advised of the possibility of such damages The technical information contained herein regarding the features and specifications is subject to change without notice For the latest warranty coverage information refer to the Warranty and Return Policy under the Support section of the Gefen Web site at www gefen com PRODUCT REGISTRATION Please register your product online by visiting the Register Product page under the Support section of the Gefen Web site 93 LICENSING IwIP is licenced under the BSD licence Copyright c 2001 2004 Swedish Institute of Computer Science All rights reserved Redistribution and use in source and binary forms with or without modification are permitted provided that the following conditions are met 1 Redistributions of source code must retain the above copyright notice this list of conditions and the following disclaimer 2 Redistributions in binary form must reproduce the above copyright notice this list of conditions and the following disclaimer in the documentation and or other materials provided with the distribution 3 The name of the author may not be used to endorse or promote products derived from this software without specific prior written permission THIS SOFTWARE IS PROVIDED BY THE AUTHOR AS IS AND ANY EXPRESS OR IMPLIED WARRANTIES INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR P
26. e makes is easier to keep track of each output device during the routing process The output name may contain a combination of letters and numbers Special characters and spaces are not permitted If a space is required as part of the out put name use the underscore character Syntax set output name param2 Parameters 1 Output 1 32 param2 String 15 characters max Example set output name 2 LCD display LCD display is assigned to output 2 62 RS 232 TELNET COMMANDS show_temp Command The show_temp command displays the temperature for each input and output board inside the matrix Syntax show temp Parameters None Example show temp Temperature result C deg for UI board 31 Temperature result C deg for BP board sensorl Mindspeed 47 sensor2 power 35 Temperature result C deg for Inputs board Board 1 2 1139 133 2 37 131 3134 130 4132 128 Temperature result deg for Outputs board Board 1 2 1144 38 2146 38 3145 36 4143 36 63 RS 232 TELNET COMMANDS Zshow ver data Command The Zshow ver data command displays the current hardware and firmware version Syntax show ver data Parameters None Example show ver data Firmware Realse version 0 2 35 Release date May 24 2012 Release time 14 23 39 64 RS 232 TELNET COMMANDS Zshow voltage Command The show temp command displays the volt
27. equired after using this command Example set telnet port 20 New Telnet port set to 20 42 865 232 TELNET COMMANDS set_telnet_username Command The set_telnet_username command assigns the Telnet username for login The underscore character _ must be included when typing the command name The user name may contain a combination of letters and numbers Special characters and spaces are not permitted If a space is required in the user name use the underscore character _ Syntax set telnet username parami Parameters 1 User name 20 characters Example set telnet username holiday Telnet Login updated holiday sgateway Command Specifies the new IP gateway The IP address must be typed using Dot decimal notation Syntax Sgateway paraml Parameters param 1 IP address Notes A reboot is required after using this command Example Sgateway 192 168 1 1 New IP Gatway set to 192 168 1 1 43 RS 232 TELNET COMMANDS Zshow telnet pass Command The Zshow telnet pass command displays the current Telnet password Syntax show telnet pass Parameters None Example show telnet pass Telnet password santaclause Zshow telnet username Command The Zshow telnet username command displays the current Telnet user name Syntax show telnet pass Parameters None Example show telnet username Telnet l
28. hanges Restores the previous names for each Preset if a change was made T1 WEB INTERFACE Routing gt gt I O Names Refresh Updates the Web page to reflect the new Input and or Output Name Modular Matrix Input_1 Name Type the desired 2 Input 2 name of each 5 3 Output or Input Input_3 in this field Click 4 Input 4 Save Changes 5 button or click the Input 5 Cancel button to 6 Input 6 restore the previous Save Changes cancel Saves the current changes Restores the previous names for each Input and or Output if a change was made 72 1 Routing gt gt 5V WARNING Use caution when applying power to inputs If the source device supplies 5V on the input then enabling the 5V may cause damage to the source and or the 32x32 DVI Matrix Refresh Updates the Web page to reflect LOCK Power the new Input and or Output Name Enables disables the power lock state See the RS 232 command lock fo command on page 59 for more information c Gha PRO 32 32 Status Configuration g Preset Names Names 5V Refresh 5 VOLT Warning Use caution when applying power to Inputs may damage your equipment LOCK Power 5 VOLT Name 5V Input 1 Input 2 Input 3 Input 4 Input 5 Input 6 In
29. hen typing the command name Syntax set http port paraml Parameters param1 Port 10 255 Notes A reboot is required after using this command Example set http port 72 New HTTP port set to 72 44 lt TCP IP SODLIDdB lt lt lt lt 00 1 91 02 80 18 192 168 1 75 Net Mask 255 255 255 0 Gateway 192 168 1 254 Web Server Port 72 Telnet Server Port 23 Telnet password at login is set to OFF Telnet welcome at login is set to OFF 40 865 232 TELNET COMMANDS set_telnet_pass Command The set_telnet_pass command specifies a new password The underscore character _ must be included when typing the command name The password may contain a combina tion of letters and numbers Special characters and spaces are not permitted If a space is required in the password use the underscore character _ syntax set http port paraml Parameters 1 Password 20 characters Notes A reboot is required after using this command Example set telnet pass santaclause Telnet password updated to santaclause 41 RS 232 TELNET COMMANDS Zset telnet port Command Specifies a new Telnet listening port The underscore character must be included when typing the command name Syntax set telnet port paraml Parameters param1 Port 0 255 Notes A reboot is r
30. iae tito EEE EEEE EE 40 Ibs 18 kg 92 Gefen warrants the equipment it manufactures to be free from defects material and workmanship If equipment fails because of such defects and Gefen is notified within two 2 years from the date of shipment Gefen will at its option repair or replace the equipment provided that the equipment has not been subjected to mechanical electrical or other abuse or modifications Equipment that fails under conditions other than those covered will be repaired at the current price of parts and labor in effect at the time of repair Such repairs are warranted for ninety 90 days from the day of reshipment to the Buyer This warranty is in lieu of all other warranties expressed or implied including without limitation any implied warranty or merchantability or fitness for any particular purpose all of which are expressly disclaimed 1 Proof of sale may be required in order to claim warranty 2 Customers outside the US are responsible for shipping charges to and from Gefen 3 Copper cables are limited to a 30 day warranty and cables must be in their original condition The information in this manual has been carefully checked and is believed to be accurate However Gefen assumes no responsibility for any inaccuracies that may be contained in this manual In no event will Gefen be liable for direct indirect special incidental or consequential damages resulting from any defe
31. ked Selecting an output does not automatically enable masking The Set button must be used to enable masking To disable masking deselect the desired outputs and press the Set button 75 Output 1 Output 2 Output 3 Output 4 Output 5 Output 6 Output 7 Output 8 Output 9 Output 10 Output 11 Output 12 Output 13 Output 14 Output 15 Output 16 Output 17 Output 18 Output 19 Output 20 Output 21 Output 22 Output 23 Output 24 Output 25 Output 26 Output 27 1 0 WEB INTERFACE 32x32 Modular Matrix Status Manage EDID Configuration Routing Preset Names Names 5V Output Masks Refresh OUTPUT MASKS Output Mask 7 Output 2 Places a check mark in each box under the Mask column Clear Clears all check marks from the Mask column Set Click this button to enable masking on the selected output s See the previous page for information on selecting inputs Cancel Restores the previous masking state for each output if a change was made Masked legend If masking has been enabled on any of the outputs then these outputs will be highlighted in blue 76 WEB INTERFACE Status gt gt In Out The Status gt gt In Out tab provides information on the hardware and firmware of the 32x32 DVI Matrix The OUTPUTS column lists each Output Card that is installed The INPUTS column lists each Inpu
32. nd for information on how to save a routing mask preset Example callpreset 2 Recall Saved Set 2 50 RS 232 TELNET COMMANDS prpreset Command The command displays the preset table In the preset table A refers to an Ac tive output refers to a Masked output Syntax prpreset Parameters None Example prpreset Preset table Set Outputs 1 32 1 2 1 2 4 5 6 7 8 9 A10 All A12 A13 14 A15 A16 17 18 A19 A20 A21 A22 A23 A24 A25 A26 27 A28 A29 A30 A31 A32 3 A0A0A20A20A20A20A20A20A0A0A0A0A0A2020A0 4 5 6 A0A0A0A0A0A0A20A20A20A2020A20A20A20A20A0 7 8 9
33. o be manually re established Syntax parami Parameters param 1 10 Example reboot 10 The system will reboot itself please wait KKKKKKKKKKKKKKKKKKKKKKK GEFEN MultiMatrix 32 x 32 FW version 0 2 35 ACKCkCKCkC lt k lt x lt lt k lt x ck lt x lt x x x x lt Establish connection with Input Board 1 Board Type DVI input 8 channels Board SN 941651 FW ver 0 1 26 Establish connection with Input Board 2 Board Type DVI input 8 channels Board SN 941655 FW ver 0 1 26 Establish connection with BP Board Type BP Board SN 945889 FW ver 0 2 30 Init Routing Please wait Loading Output 1 EDID to all locals EDID please wait Finished Loading 60 865 232 TELNET COMMANDS Zset input name Command The Zset input name command names the specified input This feature makes is easier to keep track of each input source device during the routing process The input name may contain a combination of letters and numbers Special characters and spaces are not permitted If a space is required as part of the input name use the underscore character Syntax set input name paraml param2 Parameters param1 Input 1 32 param2 String 15 characters max Example input name 1 DVD player DVD player is assigned to input 1 61 865 232 TELNET COMMANDS set_output_name Command The set_output_name command names the specified output This featur
34. ogin doc holiday 44 865 232 TELNET COMMANDS sipadd Command The sipadd command specifies a new IP address The IP address must be typed using Dot decimal notation Syntax Sipadd paraml Parameters param 1 IP address Notes A reboot is required after using this command Example Sipadd 192 168 2 127 New IP set to 192 168 2 127 45 RS 232 TELNET COMMANDS snetmask Command The snetmask command specifies a new net mask The IP address must be typed using Dot decimal notation Syntax Snetmask paraml Parameters param 1 IP address Notes A reboot is required after using this command Example 1snetmask 255 255 255 0 New IP Mask set to 255 255 255 0 46 RS 232 TELNET COMMANDS Zuse telnet pass Command The Zuse telnet pass command enables disables the Telnet password on login Syntax tuse telnet pass parami Parameters param1 Telnet password use state 10 11 Notes A reboot is required after using this command Example use telnet pass 0 Telnet password at login is set to OFF use telnet pass 1 Telnet password at login is set to ON 47 RS 232 TELNET COMMANDS Masking maskout Masks the specified outputs unmaskout Unmasks the specified outputs maskout Command The maskout command disables masks the specified outputs on the matrix Syntax maskout paraml param8 Parameters param8 Outp
35. olo Set to default EDID on Local Input ediddstoba Read downstream EDID and stores in EDID Bank ediddstolo Read downstream EDID and stores into a Local EDID lock_edid Locks Local EDID and disables auto loading after power up prbaedid Read downstream EDID from bank and sends to serial port ordsedid Read downstream EDID and sends to serial port poredidst Spools the EDID details to the serial port porloedid Read Input Local EDID and sends to serial port edidbatolo Command The edidbatolo command reads an EDID from an EDID bank and stores it to any local input Syntax edidbatolo paraml param2 param9 Parameters param1 EDID bank offset 1 20 param2 param9 Input list 1 32 Notes If param2 0 then the EDID in the specified bank is copied to all 32 DVI inputs If more than eight inputs need to be specified in order to receive the EDID in the specified bank the edidbatolo command must be executed twice Examples redadbatolo 2 5 6 7 Loading EDID bank 2 to locals EDID please wait Finished Loading edidbatolo 2 0 Loading EDID bank 2 to all locals EDID please wait Finished Loading 28 885 232 TELNET COMMANDS ediddetolo Command The ediddetolo command stores the Default EDID in any Local EDID Syntax ediddetolo paraml param9 Parameters param param9 Input list 1 32 Notes If param1 0 all inputs will receive the default EDID or use param1
36. ont panel LCD will indicate that Routing Mode has been selected 2 Press the desired Output button s from the top two rows of push buttons One more Output buttons may be selected 11 MODE BUTTONS 3 Select any Input from the bottom two rows of buttons A1 D8 corresponding to the source to be displayed on the output s 4 Press Set button again to complete the operation Press the Set button B 4 4 4 The front panel LCD display will indicate that the routing process is complete 12 MODE BUTTONS System Lock Mode Locking the Matrix prevents changes to any of the Matrix settings This feature is useful in case any of the front panel buttons are pressed by accident Locking the Matrix also prevents changes using the IR Remote Control Unit 1 Press the Lock button to activate System Lock Mode Press the Lock button The front panel LCD screen will display the following while System Lock Mode 2 Press the Lock button a second time to deactivate System Lock Mode MODE BUTTONS Cancelling a Function Press the Cancel button while in any mode to return to cancel the current function and display the Standby Mode screen Cancel button The 32x32 DVI Matrix front panel LCD screen as it appears in Standby mode 14 MODE BUTTONS Cycling between Information Screens Press the Cancel button more than once while in
37. or help on a specific command Unlocks locks the 5V power lock state Reboots the matrix Specifies a name for the designated input Specifies a name for the designated output Displays the internal board temperatures show_ver_data Displays the current hardware and firmware version show_voltage Displays the internal board voltages Enables disables 5V on the inputs Zactivebolo Command The activebolo command activates the boot loader when updating the firmware Refer to the Firmware Update Procedure beginning on page 67 on how to use this command Syntax activebolo Parameters None Notes This command must be typed and executed twice in order to activate the boot loader Example factivebolo 56 RS 232 TELNET COMMANDS fadefault Command The fadefault command resets the matrix to the factory default settings Executing this command will erase all local memory EDID banks reset the matrix to default routing status 1 1 2 2 etc and clear all IP settings Syntax fadefault Parameters None Notes A reboot is required after using this command Example fadefault Matrix set to factory default Please wait Routing 18 1 2526 244 Activate all Outputs Loading default EDID to all locals EDID please wait Finished Loading fw_upgrade Command The fw_upgrade command is not used in this version of firmware This command will be available in a future release
38. output modules and dual redundant hot swappable power supplies allow the Matrix to be used in the most demanding environments offering maximum flexibility for all applications How It Works The GefenPRO 32x32 DVI Matrix has 32 DVI inputs and 32 DVI outputs Using DVI cables connect 32 sources to the DVI input ports on the GefenPRO 32x32 DVI Matrix Connect the GefenPRO 32x32 DVI Matrix s 32 DVI outputs to the monitors Connect an Ethernet cable from the network to the RJ 45 connector to use the built in IP interface to control routing EDID and other commands Connect an RS 232 cable from an RS 232 control device to control the Matrix via RS 232 Plug in the power cord and power on the GefenPRO 32x32 DVI Matrix The connected monitors will show video according to the routing selection OPERATION NOTES READ THESE NOTES BEFORE INSTALLING OR OPERATING THE 32X32 DVI MATRIX There is no internal scaling in the 32x32 DVI Matrix All of the attached monitors must be able to display the resolutions output by the source devices For maximum compatibility it is recommended that only one compatible common resolution be used by all of the source devices Routing features can be accessed using the serial control interface Telnet or the built in Web Interface See page 26 86 for more information IMPORTANT If the unit is installed closed or multi rack assembly do not block the ventilation holes of the enclosure FEAT
39. put 7 Input 8 Input 9 Input 10 2 Input 2 Input Indicates the number of each Input If the input has 5V enabled it will be highlighted in green as shown 14 ipu rd Input 17 Name The current name of each input Input 18 Input 19 5V Click to select the desired Input s 20 Selecting an input does automatically Input 21 enable the 5V Use the Set button to NI ES enable the 5V Input 27 E m 73 WEB INTERFACE 32x32 Modular Matrix Places a check mark in each box under the 5V column Clear All Clears all check marks from the 5V column Set Click this button to enable 5V on the selected input s See the previous page for information on selecting inputs Cancel Restores the previous 5V state for each input if a change was made 5V ON legend If 5V has been enabled on any of the inputs these inputs will be highlighted in green See the previous page for more information 74 WEB INTERFACE Routing gt gt Output Masks Refresh Updates the Web page to reflect the new Input and or Output Name Status Manage EDIO Configuration on 5 Output Indicates the number of each output If the output has been masked it will be highlighted in blue as shown Name The current name of each output Mask Click to select the desired Output s to be mas
40. red Routing Masking Outputs EDID Management Saving the Downstream State EDID data to Local memory Saving the Default EDID to Local memory RS 232 Control IP Configuration RS 232 Telnet Commands EDID Management IP Configuration Masking Routing System Web Interface Routing Status Manage EDID Configuration Firmware Update Rack Mount Safety Information Specifications Warranty Licensing INTRODUCTION Congratulations on your purchase of the 32x32 DVI Matrix Your complete satisfaction is very important to us GefenPRO In the realm of video distribution certain features are invaluable in a commercial or broadcast environment Accommodations such as a build in power supply and flat black rack mount enclosures set GefenPRO apart from our traditional products Complex distribution units allow for professional DVI 3G SDI and HDMI signals to be routed and converted easily and seamlessly while being backed up by a renowned and dependable technical support team Gefen invites you to explore the GefenPRO product line and hopes that you find the solution that fits your needs The Gefen 32x32 DVI Matrix The GefenPRO 32x32 DVI Matrix is a modular design for professionals Each input can route different resolutions at any time to any display by switching from the included IR Remote IP control RS 232 or by using the front panel push buttons The front panel display provides information on routing status Removable input and
41. ring Diagram for the GefenPRO 32x32 DVI Matrix ETHERNET CABLE RS 232 CABLE DVI CABLE 32 DVI Sources Matrix K 32 DVI Displays P RS 232 Controller _ IP Control 7 Neues WARNING This product should always be connected to a grounded electrical socket OPERATING THE 32X32 DVI MATRIX Booting Up Standby Screen The front panel LCD of the 32x32 DVI Matrix is a 16 character 2 line display This display is used to aid in performing routing commands as well as displaying additional system information When the unit is powered on the following screens are displayed After a few moments the standby screen is displayed OPERATING THE 32X32 DVI MATRIX Displaying the Current Routing State To display the current routing status of the Matrix press any one of the Input or Output buttons on the front panel Output buttons Input buttons In the example above Input A1 is routed to Output A4 Output A5 Output A7 Output A8 Output B1 Output B2 Output B3 Output C3 Output C5 and Output C6 A source does not need to be connected to the Matrix to display the current routing state By default all inputs are routed to their respective outputs e g A1 A1 A2 A2 C3 C3 D5 D5 etc 10 MODE BUTTONS Routing Sources 1 change the current routing state press the Set button to activate Routing Mode Press the Set button 3 The fr
42. serial port Syntax paraml Parameters param1 Input 1 32 Example prloedid 7 Read local EDID 7 please wait 0 00 OxFF OxFF OxFF OxFF OxFF OxFF 0x00 0 1 OxA6 0x00 0x00 0x00 0x00 0x00 0x00 0x01 0x14 0x01 0x03 0x80 0x34 0x21 0x78 OxEE OxEE 0x91 OxA3 0x54 0 4 0x99 0x26 OxOF 0x50 0x54 0xA5 0 4 0x00 0x81 0x80 OxA9 0x40 0x71 Ox4F OxB3 0x00 OxD1 0x00 1 0x40 0xD1 0 0 0x31 0x40 0x30 0 2 0x00 0x98 0x51 0x00 0x2A 0x40 0x30 0x70 0x13 0x00 0x52 0x0E 0x11 0x00 0x00 0x1E 0x00 0x00 0x00 OxFF 0x00 0x47 0x45 0x46 0x45 4 0 5 0x58 0x50 0x54 0 5 0x53 0 4 0x00 0x00 0x00 0 0x00 0x47 0x45 0x46 0x45 0x4E 0x5F 0x58 0x50 0x54 Ox5F 0x53 0 4 0 0 0x00 0x00 0x00 OxFD 0x00 0x38 0 4 0x1E 0x53 0x11 0x00 0 0 0x20 0x20 0x20 0x20 0x20 0x20 0x00 0x34 36 865 232 TELNET COMMANDS Configuration display_telnet_welcome Enable disable the Telnet welcome message on login ipcontig Displays the current IP configuration resetip Resets the IP configuration to factory defaults set http port Sets the HTTP listening port set telnet pass Sets the Telnet password telnet port Sets the Telnet listening port telnet username Sets the Telnet user name Zdisplay telnet welcome Command Enables disables the Telnet welcome message on login Syntax display telnet welcome Parameters param1 Telnet welcome message state 10 11
43. t Card that is installed The information presented on this screen is used by Gefen Technical Support for troubleshooting purposes only 32x32 Modular Matrix S N Type FAW Ver Temp1 Temp2 Connection Power 3 3v Power 5 0 Power 1 981708 OUT 0 03 08 49 C deg 41 C deg 1 3282 mv 5064 mv 1806 mv 981809 OUT 0 03 06 50 C deg 35 C deg 1 3334 mv 1008 mv 1814 mv 77 S N Type FAW Ver Tempi Temp2 Connection Power 3 3v Power 5 0 Power 1 8v 959793 IN 0 03 08 40 C deg 32 C deg 1 1207 mv 3360 mv mv 959800 IN 0 03 06 37 C deg 30 C deg 1 1204 mv 3400 mv 0 mv WEB INTERFACE Status gt gt System The Status gt gt System tab provides additional detailed information on the 32x32 DVI Matrix hardware The information presented on this screen is used by Gefen Technical Support for troubleshooting purposes only 32x32 Modular Matrix Routing Status Manage onfiguration Log Out OFF SIN zu F W Ver 5 PTemp Power 3 3v Power 5 0v Core Power IO Power Fans Fans2 Fansa 78 WEB INTERFACE Manage EDID gt gt Assign EDID Lock Secures the Local EDID and disables the automatic loading after power up See the lock edid command on page 32 for more information Copy EDID From Select the EDID from the drop down list The EDID will be copied from
44. tart serial port boot loader Main Menu Download new program 1 Cancel cc ec ee 2 Press 1 on the computer keyboard to begin downloading program to the flash memory A message will appear in the terminal program Waiting for the file to be sent press a to abort In Hyperterminal click Transfer gt Send file Click Browse and select the file MMTX 01 0 2 31 bin Select Ymodem for the protocol Press Send on the Send File dialog box A message will appear in Hyperterminal Programming Completed Successfully Name UI e 0 2 31 bin Size 403072 Bytes The unit will exit the boot loader screen and return to the standard Hyperterminal window Repeat steps 3 11 for the file BP e 0 2 26 bin 88 FIRMWARE UPDATE 16 Amessage will appear in Hyperterminal 17 18 19 20 21 22 23 Download Completed Successfully Name MMTX BP e 0 2 26 bin Size 47536 Bytes Saved new version on Programs memory Activate Boot loader from application again with parameters activebolo 2 The unit will exit the boot loader screen and return to the standard Hyperterminal window Type the command activebolo Following text should appear on terminal screen The System detect FW on memory BP board To activate this board boot loader please type the command again with the parameter 2
45. the selected destination to the desired input s Options Default EDID Bank 1 Bank 20 Output 1 Output 32 Copy EDID From Default EDID Check Places a check mark in all boxes Clear Clears all check marks from each box Copy Copies the EDID source to the selected input s Cancel Clears all check marks from each box 79 WEB INTERFACE 32x32 Modular Matrix Log Out EDID Lock Copy EDID From 2 mmr 1 Input 1 F 2 Input 2 3 Input 3 E 4 Input 4 E mi 5 Input_5 6 Input_6 E 7 Input 7 8 Input 8 9 Input 9 Input 10 Input 11 EDID Source Output 25 Output 25 Output 25 Output 25 Output 25 Output 25 Output 25 Output 25 EDID Source Checkbox Displays the EDID source used by the Click to select the Input s to where the input In the illustration above the EDID source will be copied Selecting EDID source is Output 25 an input does not automatically copy the EDID source Click the Copy button to EDID Name copy the EDID to the input Displays the name of the EDID Input Indicates the number of each input Name The current name assigned to each input 80 WEB INTERFACE Manage EDID gt gt Bank Names 32x32 Modular Matrix Routing Status Manage EDID Configuration Bank Bank 2 Bank 4 Bank 6 B
46. this button to set the 32x32 DVI Matrix to factory default settings Reboot Click this button to reboot the 32x32 DVI Matrix 86 FIRMWARE UPDATE Firmware Update Procedure The following items are required to update firmware Computer running Windows XP RS 232 cable do not use a null modem cable Firmware files i e bin files s GefenPRO 32x32 DVI Matrix To begin the update procedure the matrix Boot Loader must be activated To activate the Boot Loader please follow the procedure below 1 Power on the matrix 2 Connect an RS 232 cable to the PC and open the terminal program using the following settings Baud rate 19200 Stop bits 1 Data bits 8 Flow control None 3 Type the command activebolo 4 following should be displayed on the terminal screen The System detect FW on memory DVI8 IN OUT boards To activate this board boot loader please type the command again with the parameter 5 To activate other board boot loader please type the command again without any parameters 5 Type the command activebolo This will begin the update process of the main board 87 10 11 12 13 14 15 FIRMWARE UPDATE The following text should appear on the terminal screen Activate new FW download boot loader Gefen MMTX Boot Loader v 3 4 Program on SPI memory don t match to UI board FW name aborting 4 Fail on reading UI FW from SPI flash S
47. using the 32x32 DVI Matrix Click the Save Settings button to apply changes Username Old Password New Password Operator gt Confirm New Password Download Current Configuration Restore Configuration Browse Warning All current settings will be lost SYSTEM CONFIGURATION Allows saving and loading of configuration files This feature allows the current state of the 32x32 DVI Matrix to be saved as a file This file can then be used to restore any previous configuration changes Restore Uploads the selected configuration file to the 32x32 DVI Matrix Download Click this button to download the current configuration to a file 85 WEB INTERFACE NOTE As of this writing the firmware update procedure is not functional from within the Web interface The firmware update procedure must be performed using RS 232 See page 87 Browse Update Selects the firmware file Updates the 32x32 DVI to be used to upgrade the Matrix with the selected 32x32 DVI Matrix firmware file HTTP Port Set Defaults Administrator Save Settings UDP Connection SETTINGS Remote UDP IP Address 192 168 2 206 Remote UDP Port 50021 Save Settings WEB LOGIN SETTINGS Username Old Password Restore Firmware Update Ul ver 03 38 Browse Factory Reset Heboot Reset Click
48. ut 1 32 Notes If param1 0 all outputs will be masked If more than eight inputs need to be specified then the maskout command must be executed twice Examples maskout 5 6 7 Masking outputs 5 6 7 Masking Output 5 Masking Output 6 Masking Output 7 maskout 0 Masked all outputs Masking all Outputs 48 RS 232 TELNET COMMANDS unmaskout Command The unmaskout command re enabled unmasks the specified outputs on the matrix Syntax unmaskout paraml param8 Parameters param8 Output 1 32 Notes If param7 0 all outputs will be masked If more than eight inputs need to be specified then the maskout command must be executed twice Examples funmaskout 5 6 7 Activate outputs 5 6 7 Activate Output 5 Activate Output 60 Activate Output 7 funmaskout 0 Activate all outputs Activate all Outputs 49 RS 232 TELNET COMMANDS Routing Recalls specified routing mask state preset Displays preset table savepreset Saves the current routing mask state to a preset Displays the routing status table Routes the specified input to the designated output s Routes the specified input to all outputs callpreset Command The callpreset command recalls a specified routing mask preset Syntax callpreset paraml Parameters param1 Routing preset 1 16 Notes See the savepreset comma
Download Pdf Manuals
Related Search