Mace 80200 motion detector
Contents
1. INSTALLATION Remove the screw from the battery compartments cover slide it down to remove the cover Install an alkaline 9 Volt battery FIG 1 Replace the battery cover and the screw FOR WALL MOUNT Using the battery cover as a template mark the location of holes and in stall anchors and screws Place the unit over the screws and slide the unit down to secure in place FIG 2 FIG 1 FIG 2 We suggest that you mount the unit between 3 to 6 5 feet 1 to 2 meters above the floor and position the adjustable sensor head to the left or right to obtain the best coverage of the protected area NOTE unit can also be installed with Velcro not included FOR SHELF TOP INSTALLATION Turning the sensor head clockwise rotate it 180 de grees so it is facing backwards The head can then be adjusted upward to the desired angle for coverage Lay the unit flat on top of a shelf as shown in figure 3 FIG 3 TO USE AN AC ADAPTOR not included The unit can be powered with an AC adaptor with out put 9V DC 200 MA with 3 5mm diameter male plug center positive Plug to the adaptor jack on the side of the unit FIG 4 FIG 4 PROGRAM SETTINGS The security code is factory set at 0 0 0 After you install a battery you can program your own security code using up to six digits If more than 6 digits are entered you will hear an error tone continued on back gt gt gt TO PROGRAM THE SECUR2. ITY CODE 1 Press the digits 0 0 0 2 Press the PROGRAM button 3 Enter your new code number up to six digits 4 Press the PROGRAM button again TO CHANGE EXISTING CODE TO A NEW CODE 1 Enter the old code number 2 Press the PROGRAM button 3 Enter your new code number up to six digits 4 Press the PROGRAM button again TO PROGRAM THE ALARM TIMING 1 Press the PROGRAM button 2 Choose one of three options e Press 1 for 30 second alarm 2 cycles 30 seconds rest in between or e Press 2 for 60 second alarm 2 cycles 30 seconds rest in between or e Press 3 90 second alarm 2 cycles 60 seconds rest in between The default setting is Option 1 TO PROGRAM THE ENTRY DELAY TIMING 1 Press the PROGRAM button 2 Choose one of three options e Press 7 for 15 second delay default setting e Press 8 for 8 second delay e Press 9 for 0 second delay instant alarm NOTE For added protection the unit can only be programmed when its set to the DISARM mode TO ARM THE UNIT 1 Enter your security code or 0 0 0 if you did not change the code 2 Press the ARM button you should hear 3 short beeps to confirm that the unit is armed NOTE e make sure the chime switch is set to OFF before arming the unit e There will be a beep after 60 seconds sensor warm up and exit delay after arming the unit TO DISARM THE UNIT 1 Enter your security code 2 Press the DISARM button you should hear one beep to confirm that the unit has
3. SHOOTING Cannot Arm Disarm the Unit e Re enter the security code to make sure it was entered correctly e if it still doesn t work remove the battery wait three minutes before replacing and try again If the Alarm Sound is Low or the Sensor is not Detecting Movement it indicates that the battery is low replace battery promptly DISCLAIMER This unit can provide valuable protec tion for your home and property if utilized properly However this unit cannot guarantee complete protec tion against burglary or robbery therefore MSI will not be held responsible for any loss or damages which may occur RACI WW EEIE SECURITY INTERNATIONAL
4. been disarmed ACTIVATING THE DOOR CHIME 1 Slide the chime switch to ON 2 Wait for 60 seconds after a beep for the sensor to warm up 3 Whenever movement is detected the unit will sound a DING DONG chime 4 Slide the switch to OFF to deactivate the door chime mode NOTE the door chime does not function when the unit is in ARM mode PANIC BUTTON Pressing the PANIC button triggers an immediate 30 second alarm To stop the alarm enter your security code and press the DISARM button TESTING THE DETECTION AREA After selecting a location for installation of the unit turn the chime on and wait 60 seconds for the sen sor to warm up Walk in front of the unit When the unit detects motion the chime will sound You can determine the coverage by walking around the area There will be no chime sound if you walk beyond the sensor s range By testing the detection range you can adjust the location and the sensor head angle for best coverage of the area you want Turn the chime off after you ve tested the unit BATTERY LOW INDICATOR When in ARM mode the LED will flash once every 3 seconds to indicate when the battery is low Change the battery promptly to ensure proper functioning INTRUSION MEMORY INDICATOR If there has been an intrusion while the unit was set to ARM mode it will be indicated by the LED flashing three times when you DISARM the system Be sure to check your home office thoroughly after entering TROUBLE
5. mace MOTION DETECTOR WITH SECURITY ALARM SSS SECURITY a ALARM 470 MODEL 80200 INTRODUCTION The Motion Alert s unique passive infrared system concentrates motion detection on an area you select The motion detector responds only when a person moves into range of the sensor and will sound an alarm In the Entry Chime mode the chime will sound each time motion is detected FEATURES e motion sensor detects motion amp activates alarm e programmable security code and entry delay timing e adjustable sensor head e built in high output 105dB alarm e alarm door chime option e panic button e program amp low battery indicator e verification tone for key pad and arm disarm e 9V battery operated AC adaptor compatible not included IMPORTANT SAFETY TIPS e Do not install alarm where it will be exposed to direct sunlight or rain e The alarm siren is very loud never put the unit close to your ear e The unit should be directed away from heat sources such as radiators heating ducts and stoves If the alarm sounds at random it is possibly located too close to a heat source Change the location or direc tion of the unit e If you make an error or the unit does not respond properly during the programming procedure or if you forget the password remove the battery and wait 3 minutes for the unit to rest then replace the battery This resets the system to the default settings so you can begin reprogramming
Download Pdf Manuals
Related Search