Philips Wireless HD AV Connect SWW1810
Contents
1. e Operations in the 5 15 5 25GHz 5 725 5 825GHz band are restricted to indoor usage only This device complies with Part 15 ofthe FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation IMPORTANT NOTE Radiation Exposure Statement e This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment This equipment should be installed and operated with minimum distance 20cm between the radiator amp your body e This transmitter must not be co located or operating in conjunction with any other antenna or transmitter The country code selection is for non US model only and is not available to all US model Per FCC regulation all wireless product marketed in US must fixed to US operation channels only Notice for Canada This device complies with RSS 210 of the Industry Canada Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation IMPORTANT NOTE Radiation Exposure Statement This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment This equipment should be installed and oper2. ARE NO OTHER EXPRESS OR IMPLIED WARRANTIES Philips liability is limited to repair or at its sole option replacement of the product Incidental special and consequential damages are disclaimed where permitted by law This warranty gives you specific legal rights You may also have other rights that vary from state to state EN 17 9 Frequently asked question The power LED on the receiver is not lit up in red in standby mode The computer screen image is not full screen on my TV 1 2 3 4 5 6 There is no video displayed on my TV screen EN Make sure that there is power supply for the transmitter and receiver Right click on an open space on your desktop Select Graphics Options gt Output to gt Digital Television Now the laptop image will only appear on your IV Once again right click on an open space on your desktop Select Screen Resolution On the pop up box increase the resolution settings till the laptop image better fits your TV screen Select OK and KEEP CHANGES when you are satisfied with your Image size Make sure that the appropriate cables are selected and inserted to the transmitter receiver and HDTV Make sure that you select HDMI as the input source on your HDTV Check the power LED and SOURCE LED on the receiver e Flashing blue power LED Make sure that the transmission range between receiver and transmitter is not over 65 feet 19 7 meters transmission distance Move
3. EN 7 The remote control POWER button INFO button IR button SOURCE button PHILIPS Press to turn the transmitter and receiver on off Displays on the HDTV the connection status of the receiver Press to switch the IR blaster frequency to meet the requirement of the source device Press to switch the audio video source inputs connected to the transmitter The Wireless HD AV Connect gives you a total wireless solution to place your HDTV set or projector anywhere you want The transmitter can transmit uncompressed video content over 65 feet 19 meters without latency The receiver can receive signals for viewing on your HDTV All you need to do is to Note Connect the transmitter to your HD devices Examples of HD devices are cable satellite box Blu Ray HD DVD player game console or computer e These devices must have an HDMI port Connect the receiver to your HDTV set Control the transmitter with the remote control 4 Installation Connect the transmitter to your HD devices You can connect two audio video sources to the transmitter at the same time but only one source can be selected and played 1 Connect the audio video source to the transmitter using the supplied HDMI cable e Connect one end of the HDMI cable to the HDMI IN connector of the transmitter There are two HDMI IN ports but only one HDMI cable is supplied lo connect two audio video sources to
4. Power Source Mode and status LED LED Solid Off Standby mode it is a red power saving mode Flashing Flashing Start up in progress It takes blue blue 15 20 seconds Flashing Flashing Searching available channels blue It occurs when the link cannot establish over 80 seconds after Initialization Solid Flashing On mode but without blue quickly input from the source device Solid Flashing On mode with blue slowly unrecognized video format Solid Solid On mode with recognized blue blue video format e Ifthe link is not established after 80 seconds move the transmitter receiver and HDTV closer to each other The maximum transmission range is up to 65 feet 19 7 meters If more than one set of Philips Wireless HD AV Connect is placed in the same room make sure that the minimum distance among each one Is 6 feet 6 inches 2 meters e If using a computer make sure the video format is supported before the video is displayed see the chapter on Technical data for information e f using a computer and the picture on your TV is not full screen see the chapter on Frequently asked questions for information 6 M ou nt yO ur 5 Hook the key holes at the back of the receiver on the screws receiver You can erther mount the receiver on the wall or on the back of the HDTV Mount your receiver on the wall 1 Select a spot near the HDTV 2 Drill two holes in the wall Make sure that the distan
5. stick the IR blaster extender cable onto the front panel of the HD device 3 After the IR blaster extender cable is connected to the transmitter you can control your HD device with the remote control Make sure that the remote control points to the receiver 4 ifthe distance between the receiver and receiver has obstruction e g the receiver is mounted at the back of the HDTV plug the IR sensor extender cable into the IR IN jack of the receiver 5 Extend and stick the IR sensor extender cable onto the front side of your HDTV Note The IR blaster support 47KHz remote signal protocol while the IR sensor supports 36KHz 56KHz NEC RC5 RC6 remote signal protocol Install remote control batteries BI Caution e Risk of explosion Keep batteries away from heat sunshine or fire Never discard batteries in fire e Risk of decreased battery life Never mix different brands or types of batteries e Risk of product damage When the remote control is not used for long periods remove the batteries 1 Open the battery compartment 2 Insert two AAA batteries with correct polarity as indicated 3 Close the battery compartment 5 Activate your Wireless HD AV Connect and set up the link Turn on the power of your HDTV HDMI 1 MN Go to the source menu under the settings menu of your HDTV 2 Select the HDMI input to which the receiver Is connected On screen
6. the transmitter closer to the receiver e Solid blue power LED slow and flashing source LED 1 Make sure that the frame rate and video resolution of your source device equipment are supported and conformed to the technical specification 2 Connect the source device to your TV with an HDMI cable to check the compatibility of the video format 3 Make sure that the video solution your source device Is supported See the chapter Technical data e Solid blue power LED quick and flashing source LED 1 Make sure that the proper cables are connected among the transmitter receiver and HDTV 2 Make sure that the source devices connected to the transmitter are powered on If the picture quality is poor Make sure that the video resolution of your source device what do do matches the resolution of your HDTV e Make sure that the transmission range between receiver and transmitter is not over 65 feet 19 7 meters transmission distance For information see the chapter on Technical data cannot hear any sound or the Make sure that the TV volume is adjusted correctly sound is poor what do do Make sure that the TV volume is not set to minimum or the sound Is not muted e Make sure that the audio format is supported e Make sure the HDMI cable of the transmitter is connected correctly Tip For information see the chapter on Technical data section Product specification cannot contro
7. where they exit from the apparatus Only use attachments accessories specified by the manufacturer 12 Use only with the cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart Is used use caution when moving the cart apparatus combination to avoid Injury from tip over 13 Unplug this apparatus during lightning storms or when unused for long periods of time Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped 15 Battery usage CAUTION To prevent battery leakage which may result in bodily injury property damage or damage to the unit e Do not mix batteries old and new or carbon and alkaline etc e Remove batteries when the unit is not used for a long time Apparatus shall not be exposed to dripping or splashing 47 Do not place any sources of danger on the apparatus e g liquid filled objects lighted candles Warning e Use only the provided power adapter EN 5 2 Your Wireless HD AV Connect Congratulations on your purchase and welcome to Philips To fully benefit from the support that Philips offers register your product at www philips co
8. Register your product and get support at www philips com welcome SWW1810 PHILIPS BE EN User manual 3 PHILIPS Contents 1 Important 4 Safety 4 2 Your Wireless HD AV Connect 6 What is in the box 6 3 Overview 7 The transmitter The receiver The remote control 8 4 Installation J Connect the transmitter to your HD devices 9 Connect the receiver to the HDTV set 9 Connect the IR blaster and IR sensor extender cables 10 Install remote control batteries 10 5 Activate your Wireless HD AV Connect and set up the link T Turn on the power of your HDTV 11 Activate the wireless link 12 6 Mount your receiver 13 Mount your receiver on the wall 13 Mount your receiver on the back of the HDTV 14 7 Technical data 13 Supported resolution 15 Product specifications 15 8 Notice 16 Notice for USA 16 Notice for Canada 16 Recycling 17 Disposal of your old product and batteries 17 One Year Limited Warranty 17 9 Frequently asked question 18 EN 1 Important Safety CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN NN This bolt of lightning indicates uninsulated material within your unit may cause an electrical shock A A The exclamation mark calls attention to features for which you should read the enclosed literature closely to prevent operating and maintenance problems UN Warning CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PART
9. S INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL To reduce the risk of fire or electric shock this apparatus should not be exposed to rain or moisture and objects filled with liquids such as vases should not be placed on this apparatus Caution e To prevent electric shock fully insert the plug For regions with polarized plugs lo prevent electric shock match wide blade to wide slot Important Safety Instructions Read these instructions Keep these instructions Heed all warnings Follow all instructions 0000 N EN 5 Do not use this apparatus near water 6 Clean only with dry cloth 7 Do not block any ventilation openings Install in accordance with the manufacturer s instructions Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat 9 Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong are provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet AC Polarized Plug Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point
10. ated with minimum distance 20cm between the radiator amp your body EL Caution The device for operation in the band 5150 5250 MHz is only for indoor use to reduce the potential for harmful interference to co channel mobile satellite systems the maximum antenna gain permitted for devices in the band 5725 5825 MHz shall comply with the e i rp limits specified for point to point and non point to point operation as appropriate Recycling ab Your product is designed and manufactured with high quality materials and components which can be recycled and reused Never dispose of your product with other household waste Please inform yourself about the local rules on the separate collection of electrical and electronic products The correct disposal of your old product helps prevent potentially negative consequences on the environment and human health The packaging of this product Is intended to be recycled Contact your local authorities for information about how to recycle the packaging When this logo is attached to a product it means a financial contribution has been paid to the associated national recovery and recycling system Disposal of your old product and batteries Your product is designed and manufactured with high quality materials and components which can be recycled and reused Never dispose of your product with other household waste Please inform yourself about the local rules on t
11. ce between the two holes is 1 25 32 45 mm and the diameter of the hole is 3 16 5 mm 3 Punch the supplied two anchors into the two holes on the wall A Put the two screws into the anchors and leave 1 8 3 mm to mount the receiver on EN 13 Mount your receiver on the back of the HDTV 1 Remove the white protective film from one of the supplied adhesive tapes 2 Secure the glued side of the adhesive tape and attach it to the central bottom area of the receiver 3 Select a flat location on the rear side of the HDTV 4 Remove the white protective film from the other adhesive tape 5 Secure the glued side of the adhesive tape and attach it to the selected rear side of the HDTV 6 Align the adhesive tape on the receiver with the one on the HDTV until both the receiver and HDTV are mounted together firmly e The use of adhesive tapes is an alternative mounting option when the receiver cannot be fixed When you mount the receiver at the back of the HDTV avoid blocking the ventilation holes of the HDTV For safety reason check regularly if the HDTV and recelver are mounted together firmly The receiver is not recommended for in the wall installation Technical data Supported resolution V
12. display on HDTV On screen display lg 227 x and Y Y al HDMI CHA Y al HDMI CH1 ji Y al HDMI Mode and status Standby mode it is a power saving mode Start up In progress It takes 15 20 seconas Searching available channels It occurs when the link cannot establish over 80 seconds after Initialization On mode with unrecognized video format On mode but without input from the source device On mode with recognized video CH1 1080P format EN 11 Activate the wireless link Switch on the transmitter and receiver In standby mode a red power LED displays on the transmitter and receiver You can then turn on the transmitter and receiver in the following ways PHILIPS Press on the remote control L gt Both the transmitter and receiver are turned on NE Press O on the transmitter and receiver Establish the link between the transmitter and receiver A flashing blue power LED displays until the signal link between the two units are established Normally it takes around 15 20 seconds for the link to establish successfully 12 EN Select the source on the transmitter Press the source buttons on the remote control transmitter or receiver until you see the available video from your device Tip e For information on the LED indicator status see the section on LED indicator status of the transmitter LED indicator status of the transmitter and receiver
13. he separate collection of electrical and electronic products and batteries The correct disposal of these products helps prevent potentially negative consequences on the environment and human health Your product contains batteries which cannot be disposed of with normal household waste Please inform yourself about the local rules on separate collection of batteries The correct disposal of batteries helps prevent potentially negative consequences on the environment and human health Please visit www recycle philips com for additional information on a recycling center In your area HIGH DEFINITION MULTIMEDIA INTERFACE HDMI and HDMI logo and High Definition Multimedia Interface are trademarks or registered trademarks of HDMI licensing LLC in the United States and other countries One Year Limited Warranty Philips warrants that this product shall be free from defects in material workmanship and assembly under normal use in accordance with the specifications and warnings for a period of one year from the date of purchase This warranty extends only to the original purchaser of the product and is not transferable lo exercise your rights under this warranty you must provide proof of purchase in the form of an original sales receipt that shows the product name and the date of purchase For customer support or to obtain warranty service please visit our website www philips com support or dial in 1 888 744 5477 THERE
14. ideo format Resolution timings Primary CEA video timing 480p 640x480p 59 94 60Hz 480p 720x480p 59 94Hz 480p 720x480p 60Hz 576p 720x576p 50Hz 720p 1280x720p 50Hz 720p 1280x720p 59 94 60Hz 10801 1920x10801 50Hz 1080i 1920x1080 59 94 60Hz 1080p 60 1920x1080p 50Hz 1080p 60 1920x1080p 59 94 60Hz Secondary CEA video timing 1080p 24 1920x1080p 23 98 24Hz 1080p 24 1920x1080p 25Hz 1080p 24 1920x1080p 29 97 30Hz Product specifications General specification Video resolution HDMI input 1080p 10801 720p 576p 480p Supported audio formats Digital audio up to 6 Mbps AC3 and DTS Analog audio 32 96 KHz and 16 24 bits per audio sample Transmission distance Maximum 65 feet 19 7 meters Antennas High performance internal antennas Operating frequencies 5 15 5 25 5 25 5 825 GHz Power supply Input AC 100 240V Output DC 5V 2A Operating temperature OO EO Transmitter interfaces A V interfaces HDMI input Two Type A Control signal interfaces IR blaster extender 2 5mm jack Power interface Power input 5V DC jack Switches Top power switch One Top source switch One LEDs Power LED 1 x blue red LED Source LED 2 x blue LED Dimensions 194 8 x 146 8 x 31 mm W x L x H Receiver interfaces A V interfaces HDMI output One Type A Control signal interfaces IR sensor available Power interface Power input 5V DC jack Switches Top power switch One T
15. l the source e Make sure that the IR blaster and IR sensor extender cables are device with the IR blaster facing the IR lens ofthe HD device Press the IR button on the remote control to change the IR blaster frequency based on the requirement of the source device Tip For information see the chapter Installation section Connect to IR blaster and IR sensor extender cables EN 19 20 EN a PHILIPS 2011 Koninklijke Philips Electronics N V IFU SWW1810 EN V2 0 All rights reserved WK11485
16. m welcome What is in the box Note e Make sure you have all these items in the box Contact your dealer for any missing or damaged items PHILIPS Transmitter PHILIPS PHILIPS Receiver PHILIPS Remote control 6 EN HDMI cable IR blaster extender cable Power adapter for the transmitter and receiver x 2 IR sensor extender cable Pe En iD Anchors x 2 Adhesive tape x 2 Screws x 2 Quick start guide User manual 3 Overview The transmitter Front view DOD PHILIPS 1 Source LEDs t displays the current source input 2 SOURCE Press to switch the button source input of the transmitter 3 Power button Press to turn the with the LED transmitter on off indicator Rear view YO 00 QU 1 DC IN jack Connect the power adapter of the transmitter 2 amp 3 HDMIIN Connect the HD audio adapters video device with the HDMI cables a IR OUT Plug in the IR blaster blaster extender cable extender jack The receiver Top view DOD 4 m 2 2 2 2 PHILIPS 1 Source LEDs Indicators for HDMI and HDMI2 2 Power Press to turn the receiver button with on off the LED indicator 3 Source Press to select the button source input Rear view D ODD 1 DCIN Connect the power adapter jack of the receiver 2 HDMI Connect the HDTV with an OUT HDMI cable adapter 3 IR IN jack Plug in the IR sensor extender cable
17. op source switch One LEDs Power LED 1 x blue red LED Source LED 2 x blue LED Signal quality status On screen display Dimensions 194 8 x 146 8 x 31 mm W x L x H EN 15 8 Notice Notice for USA This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help FCC Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment
18. the transmitter at the same time you need an additional HDMI cable e Connect the other end of the HDMI cable to the HDMI OUT connector of the video source 2 Connect the supplied power adapter to the transmitter e Connect one end of the power adapter to the DC IN jack of the transmitter e Connect the other end of the power adapter to a power outlet L The power button of the transmitter is lit in solid blue and turns red In standby mode Connect the receiver to the HDTV set High Def Flat panel TV 1 Connect the receiver with an additional HDMI cable not supplied e Connect one end of the HDMI cable to the receiver e Connect the other end to the HDMI IN connector of your HDTV 2 Connect the supplied power adapter to the receiver e Connect one end of the power adapter to the DC IN jack of the receiver e Connect the other end of the power adapter to a power outlet Ls The power button of the receiver is lit in solid blue and turns red In standby mode EN 9 Connect the IR blaster and IR sensor extender cables Tip e If you cannot use the remote control of your device follow the steps in this section to connect the sensor extender cables HDMI D sww1810T Connect the infrared blaster or sensor extender cables if necessary 1 Plug the IR blaster extender cable into the IR OUT blaster extender jack of the transmitter 2 Extend and
Download Pdf Manuals
Related Search