Pyle PT649D
Contents
1. of DECK A 9 Then press the PLAY button of DECK A 10 Press the RECORD button of DECK B 11 Press the PAUSE again of DECK A to release the pause mode The unit will start the synchronized dubbing operation 12 To stop dubbing operation press the STOP EJECT button of DECK B Note Do not change dubbing speed during dubbing operation SPECIFICATIONS UY DO PPE AE ME neat Stereo double cassette deck Track system 655 4 track 2 channel Tape speed 0000 eee 4 8 cm sec Frequency response 20dB recording Chrome tape cierres 40 15 000Hz 3dB Normal tape 40 14 000Hz 3dB 0 dB recording Chrome tape cescciircsiiiceriri 40 8 000Hz 3dB Normal tape eee 40 8 000Hz 3dB S N ratio 58dB Wow and flutter lt 0 2 DIN45500 Crosstalk anaiari sorire 40dB 1 khz Harmonic distortion less than 1 at 1 Khz OVU 3 H D Normal tape Channel separation 40dB 1 khz GAG cienne iani Deck A For Playback Deck B For recording playback 2 gap ferrite head for erasure Motor DC servo motor x 2 Fast Forward Rewind time Approx 100 sec with C 60 cassette Input terminals LINE IN X 2 Min input level 600mV 0dB Input impedance 50 kQ Output terminals LINE OUT X 2 output level 600mV 0dB output impedance 5 KQ Power requirement AC220V 50Hz power voltage 230V 50Hz For U Kies se er2. record level volume to the left position and vice versa In normal state the sound source level is between the red and green spots that s 0dB 1 Press the TOP EJECT BUTTON and insert a cassette ce 5 2 When Cr02 tape is used for recording press the REC Cr02 switch Press the record button The level meter at the peak level indicator will shift and the REC light will be lit up indicating that recording is underway 4 Press the STOP EJECT button to stop recording at any time Pause Press this button to momentarily stop tape travel during recording Re press this button for pause release and recording restart Dubbing operation DECK A DECK B This unit enables you to dub a recorded tape to another tape by using the built in double deck mechanisms It is performed only one way from DECK A to DECK B Preparation 1 Insert a cassette for playback in DECK A 3 2 Select tape DIRECTION button FFWD or REW for the desired location of the tape to the beginning 3 Insert a cassette into DECK B 4 Select the dubbing speed by the dubbing High speed switch 5 There are two dubbing speeds high speed and normal speed 6 For high speed dubbing press the High speed switch The light at the indicator will be lit up and high speed dubbing is then activated 7 Normal speed dubbing requires no pressing of the High Speed Switch No light will be shown at the indicator at all 8 Press the PAUSE button
3. SPRO 2 PT 649D U Automatic Stop System High Speed Dubbing Dynamic Noise Reduction Adjustable Recording Level 110 200 Volt Switchable Includes 19 Rack Mount Adaptors C 110 220 SWITCHABLE PANEL INFORMATION O0 Q PT 649D NOISE FEDUCTION CICIO O Q 1 ON STANDBY SWITCH Depress button to switch ON the unit Press release to switch OFF unit into STANDBY MODE If the unit is left unattended for long periods remove the 13 AMP plug from the power socket 2 CASSETTE HOLDER 3 DYNAMIC NOISE REDUCTION Switch on Dynamic NR key for better result when tapes with Dynamic Noise reduced are playing 4 PEAK LEVEL INDICATOR These indicate the recording level during recording and output level during playback The LED indication varies with the signal strength during recording and playing REC This lights when Deck B is in the recording the record pause mode HIGH SPEED This lights when in t
4. ect 240V 50Hz For U S A amp Canada 110V 60Hz Power consumption watts VA Rated watts Maximum Dimensions 360mm x 128m x246mm WxHxD Weight 4Kg 8 5 Ibs ACCESSORIES Pin plug cord 2 Design and specifications are subject to change without notice
5. he high speed dubbing PLAY Cr02 METAL This lights when the Cr02 metal function is operated ERC Cr02 This lights when Cr02 function is operated 5 TAPE COUNTER and RESET button DECK B When recording or playing you can use the tape counter to count the tape length 6 REC LEVEL SWITCH Adjust the record level 7 CASSETTE OPERATION BUTTONS e REC gt play Press to play the tape lt 4 lt rewind Press to rewind the tape gt gt fast forward Press to fast forward the tape stop eject Press to stop the tape Pressing this button after the tape stops to open the cassette holder The tape automatically stops when it reaches the end I I pause Press to temporarily stop the tape in the record or playback mode Press it again to release the pause mode and restart the tape 8 REC Cr02 SWITCH For recording with Cr02 tape 9 HIGH SPEED DUBBING SWITCH When you need high dubbing press this switch and the relative light will be lit 10 DUBBING SWITCH Press the DUBBING button when you need Dubbing at normal speed 11 PLAY Cr02 SWITCH When play Cro2 tape press this button OPERATING PROCEDURES VOLTAGE SELECTOR Use this switch to select the proper Voltage for your region Playback a recorded tape DECK A or DECK B 1 Switch on the power of the unit 2 Press the STOP EJECT button and insert a recorded cassette For Cr02 metal tape further press the Cr02 metal switch and the lig
6. ht at the indicator will be lit up Press the PLAY button Adjust the AMPLIFIER VOLUME and GRAPHIC EQUALIZER controls for your desired sound level and taste Press the STOP EJECT button to stop playback at any time Fast forward and rewind DECK A or DECK B For fast winding or rewinding the tape press the FFWD or REW button Press the STOP EJECT button when the desired location has been reached When the end of the tape has been reached the FFWD or REW button will be released automatically Pause DECK A or DECK B Press the PAUSE button to momentarily stop tape travel during playback or recording Re press the button for pause release and playback or recording to re start Full automatic stop DECK A or DECK B Press the STOP EJECT button to stop playback or recording at any time When the end of the tape has been reached any of the PLAY REC REW or FFWD buttons if pressed will be automatically released and the head block completely separates from the tape and capstan This protects tape and prevents pinch roller wearing out RECORDING DECK B When recording use the DECK B Manually level control recording for external source This unit has record level volume to adjust the record level Usually the volume has a center click When it reached the center click position the tapes can be recorded normally If the sound source signal is too strong a red spot will be appeared in the record level indicator You can adjust the
Download Pdf Manuals
Related Search