Vocopro CDR-1000 PRO
Contents
1. Press the PLAY button on the front panel to begin disc playback Press the buttons once to skip to the previous or next track or hold them down to scan through a track Press the STOP button to cease playback of the disc NOTE You cannot use the RECORDING LEVEL control to adjust the volume when playing a disc in Playback Mode You will need to use the volume on the mixer or amp that you are outputting to Recording onto a Disc Preparing to Record f using a CD R make sure that there is not already data stored on the disc as you will be unable to burn anything onto it f you are going to rewrite onto a CD RW be sure to erase the data using the ERASE feature the CDR 1000 PRO before recording See the Erasing instructions in this manual e f using 8cm CD R RW disc you must use the Digital input on the rear panel of the CDR 1000 PRO The Analog input does not support 8cm CD R RW NOTE Be sure that your disc is clean and in good shape for recording Excessive dust scratches markings etc could prevent successful recording NOTE Make sure all players or mixers are connected to the proper inputs and outputs of the CDR 1000 PRO Most standard CD players Car audio home audio etc do not support CD RW discs If using CD RW discs make sure that your CD player specifies that it is CD RW compatible Operations cont Recording 1 Switch the CDR 1000 PRO to Record Mode by pressing the RECORD butt2. Erasing a Disc Troubleshooting opecifications and Features Features e Burn music to CD R CD RW 8cm CD R and 8cm CD RW live and in real time without a computer Hackmount ready and requires only 1 RU of rackspace e Simple Finalizing of CD R RWs Create CDs that can be played in standard CD players Erase data from CD RW discs e Digital Coaxial audio input compatible with 44 kHz RCA and balanced XLR audio line in out connections Headphone input so you can monitor your recording Create separate tracks while recording live Recording Volume control for pro sounding recordings The analog input does not support 8cm CD R RW discs Use the digital input on the rear panel of the CDR 1000 PRO when burning to CD R RW disc Most standard CD players Car audio home audio etc do not support CD RW discs If using CD RW discs make sure that your CD player specifies that it is CD RW compatible Specifications Compact Disc Recordable Playback format Recording formats CD R CD RW 8cm CD R 8cm CD RW Audio and Data discs Guantization 24 bit linear Sampling Frequency Frequency Response Power Consumption Accessories Power Cord RCA cable 17 x 1 8 x 18 7 1 0 Configuration Analog Input Connector XLR 3 31 Type RCA Input Impedance 10k balanced 10k Analog Output Connector XLR 3 32 Type RCA Output Impedance 600 balanced 600 Head Phone Output Connector Va Stereo
3. NOTE The CDR 1000 PRO will not automatically change to a new track when copying a CD 10 Operations cont Finalizing a Disc After you have finished recording onto a disc you will need to FINALIZE it so that it will be compatible with standard disc players If a disc has not been finalized it can only be played back in the CDR 1000 PRO NOTE The CDR 1000 PRO must be in Playback Mode in order to finalize a disc Make sure it is not in Record Mode Follow these steps to successfully FINALIZE your disc 1 Insert the disc into the CDR 1000 PRO s disc tray and close the tray 2 If in Record Mode press the STOP button to enter Playback Mode The Finalizing function only works in Playback Mode 3 Press the FINALIZE button 4 The display screen will ask you if you want to continue with the finalizing process Press the START button to begin finalizing The display screen will say FINALIZING until the process is finished The display will show how much time is left in the Finalizing process When the disc has been finalized it is ready to be played in standard CD players l e Car stereos CD ROM compatible drives home stereos etc NOTE You will not be able to burn any more music onto a disc once it has been finalized Erasing the Contents of a CD RW The ERASE function only works on CD Rewritable CD RW discs Follow these steps to successfully ERASE the contents of your CD RW disc 1 Insert the CD RW disc into the CD
4. equipment will provide a lifetime of fun and enjoyment Since hearing damage from loud noise is often undetectable until it is too late this manufacturer and the Electronic Industries Association s Consumer Electronics Group recommend you avoid prolonged exposure to excessive noise This list of sound levels is included for your protection Some common decibel ranges Level Example 30 Quiet library Soft whispers 40 Living room Refrigerator Bedroom away from traffic 50 Light traffic Normal Conversation 60 Air Conditioner at 20 ft Sewing machine 70 Vacuum cleaner Hair dryer Noisy Restaurant 80 Average city traffic Garbage disposals Alarm clock at 2 ft The following noises can be dangerous under constant exposure Level Example 90 Subway Motorcycle Truck traffic Lawn Mower 100 Garbage truck Chainsaw Pneumatics drill 120 Rock band concert in front of speakers 140 Gunshot blast Jet plane 180 Rocket launching pad Information courtesy of the Deafness Research Foundation Table of Contents Safety instructions FCC Information Welcome Listening For a Lifetime Specifications and Features Mounting Getting Connected Inputting Audio Switching Between Analog and Digital Outputting Audio Controls and Functions Front Panel Rear Panel Operations Choosing between Playback Mode and Record Mode Preparing a Disc for Playback Playing a Disc Recording on to a Disc Pausing Recording Creating Tracks on a Disc Finalizing a Disc
5. ASTER seen omar nora orn BV A Mp3 MEE ees NOTE Match up the colors of the RCA cables to the colors of the inputs White into white and red into red Gar 3 Connecting to the Digital Coaxial input compatible with 44 1 kHz CDG 555 CDR 1000 PRO ANALOG 1 0 INPUT SHT LEFT RIGHT O C2 INBAL BAL 1 Using an RCA cable connect one end to the Digital Input on the rear panel of the CDR 1000 PRO 2 Connect the other end of the RCA cable to the digital coaxial output on your disc player NOTE If your player does not have a digital output you will not be able to use the CDR 1000 PRO s Digital Input 4 0101010101010 Getting Connected cont Switching between Analog and Digital 1 When in Playback Mode press the source button on the front of the CDR 1000 PRO 2 There will be an A in the display screen when in Analog mode and a D when in Digital mode NOTE You will not be able to switch between Analog and Digital modes while the CDR 1000 PRO is in Record Mode ATTENTION If you are burning onto CD R RW you must use the Digital input The Analag input does not support 8cm CD R RWs CDR 1000 PRO Outputting Audio 1 Using Two XLR Cables and Connecting to the BALANCED XLR inputs 1 Connect the female end of each cable to the BALANCED left and right XLR
6. CT SYMBOL button This button is used to open and close the DISC tray 5 PREV lt lt button This button is used to scan backwards through a track or to go back to a PREVIOUS track Press it once to skip to the beginning of the current track twice quickly to jump to the previous track and hold it down to scan backwards through the current track 6 NEXT gt gt button This button is used to scan forwards through a track or to advance to the NEXT track Press it once to skip to the next track and hold it down to scan forwards through the current track 7 PLAY PAUSE button This button is used to begin playing a disc when it is not already playing It will PAUSE disc that is already playing START recording When in Record Mode Press this button while in Record Mode to start recording See the Operations section of this manual for in depth recording instructions Controls and Functions cont Front Panel Controls and Functions 8 STOP CANCEL button This button is used to STOP disc PLAYBACK CANCEL recording When in Record Mode Press this button to stop recording 9 RECORD RECORD symbol button Press this button to switch the CDR 1000 PRO to Record Mode Use this button to start a new track while the CDR 1000 PRO is already recording NOTE Recording will not actually start until you press the START button 10 POWER switch Use this to turn the power on and off 11 RECOR
7. D LEVEL control Use this to adjust the volume level that is being recorded onto the disc NOTE The record level control only adjusts music that is being input into the CDR 1000 PRO It will not control the volume of a disc that is being played in the CDR 1000 PRO s disc player 12 SOURCE button Switches between Analog and Digital input mode Select Analog when using the RCA or XLR audio inputs and Digital when using the Digital Coaxial audio input NOTE The analog input does not support 8cm CD R RW discs Use the Digital input on the rear panel of the CDR 1000 PRO when burning to an 8cm CD R RW disc and make sure it is in Digital input mode 13 ERASE button Use this button to erase data from a CD Rewritable CD RVV disc NOTE This function only works on CD Rewritable CD RW discs and will not work on CD Rs 14 FINALIZE button Use this to finalize a disc Finalizing a disc enables that disc to be played in any standard disc player l e Car stereo home stereo If a disc is not finalized it can only be played in the CDR 1000 PRO s disc player 15 HEADPHONE jack Plug in your headphones here Controls and Functions Rear Panel Controls and Functions AC INPUT 155 SO0V 24 V S0 60HZ BAL UNBAL BAL UNBAL BAL UNBAL BAL UNBAL 1 BALANCED XLR inputs Use these to input stereo audio using a pair of balanced XLR cables CDR 1000 PRO must be in Analog mode 2 UNBALANCED FCA inputs Use these to input
8. Jack Load Impedance Maximum Output Level 300mW Coaxial Input IEC60958 Connector Input Impedance NOTE Specifications are subject to change without prior notice Mounting Use the included mounting brackets to mount the CDR 1000 PRO into a 19 rack case The CDR 1000 PRO requires 1 RU of available rackspace Installing the Mounting Brackets onto the CDR 1000 PRO Position the mounting brackets on the CDR 1000 PRO with the tabs facing away from the player Line up the three holes on the mounting bracket with three holes on the sides of the CDR 1000 PRO Use the included screws to secure the brackets on each side of the CDR 1000 PRO NOTE You will need a screwdriver for securing the rack ears Screwdriver not included Mounting the CDR 1000 PRO Into a Rackcase To mount carefully place the CDR 1000 PRO in the rack space of your case The CDR 1000 PRO takes 4 screws to mount Make sure holes are aligned evenly Use an alternating X rota tion when screwing to ensure even tension and alignment You will need 19 Rack Case 4 Mounting Screws Phillips head Screwdriver bo oo oo oo o Getting Connected Connecting the Headphones Using headphones with connection connect them to the HEADPHONE input jack on the CDR 1000 PRO Inputting Audio The CDR 1000 PRO can be easily integrated into your audio system for easy recording and without compromising th
9. NEZ 929 727 THE SINGER S ULTIMATE CHOICE COR IGOOPRO Em CDB 1O0O0 O0 PRO Professional Single Rack CD Recorder and Player U D C U JJ Safety Instructions CAUTION RISK OF SHOCK CAUTION To reduce the risk of electric shock do not remove cover or back No user serviceable parts inside Only refer servicing to qualified service personnel Explanation of Graphical Symbols The lightning flash amp arrowhead symbol within an equilateral triangle is intended to alert you to the presence of danger The exclamation point within an equilateral triangle is intended to alert you to the presence of important operating and servicing instructions WARNING To reduce the risk of fire or electric shock do not expose this unit to rain or moisture 1 Read Instructions All the safety and operating instructions should be read before the appliance is operated 2 Retain Instructions The safety and operating instructions should be retained for future reference 3 Heed Warnings All warnings on the appliance and in the operating instructions should be adhered to 4 Follow Instructions All operating and use instructions should be followed 5 Attachments Do not use attachments not recommended by the product manufacturer as they may cause hazards 6 Water and Moisture Do not use this unit near water For example near a bathtu
10. R 1000 PRO s disc tray and close the tray 2 If in recording mode press the STOP button to enter Playback Mode The Erasing function only works in Playback Mode 3 Press the ERASE button The LCD display will ask you if you are sure you want to ERASE 4 Press the START button to begin erasing the data from the CD RW disc The display will show how much time is left in the erasing process CDR 1000 PRO NODC T 12 Finalizing 85 18 Audio NOTE The erasing process cannot be cancelled once it has begun so be sure that you want to erase the disc Disclaimer VocoPro will not be held liable for any erased data PIC of the display showing this info 41 Troubleshooting Problem There is no power when the power switch is turned on The input source i e disc player karaoke machine is playing but there is no sound from the output source i e amp or mixer The LED display says ERROR FINALIZED DISC The LED display says ERROR CDRW DISC ONLY The final recording sounds too loud or distorted am unable to record onto an CD R RW disc The CD RW disc will not play in my CD player Car audio home audio etc Solution sure the power cord is firmly connected to the AC IN terminal on the back of the CDG 1000 PRO Make sure the power cord is securely connected to the power outlet or the surge protector power strip sure your surge pr
11. b or in a wet basement and the like 7 Carts and Stands The appliance should be used only with a cart or stand that is recommended by the manufacturer 7 A An appliance and cart combination should be moved with care Quick stops excessive force and uneven surfaces may cause an overturn 8 Ventilation The appliance should be situated so its location does not interfere with its proper ventilation For example the appliance should not be situated on a bed sofa rug or similar surface that may block the ventilation slots 9 Heat The appliance should be situated away from heat sources such as radiators heat registers Stoves or other appliances including amplifiers that produce heat 10 Power Sources The appliance should be connected to a power supply only of the type described in the operating instructions or as marked on the appliance 11 Grounding or Polarization Precautions should be taken so that the grounding or polarization means of an appliance is not defeated 12 Power Cord Protection Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them paying particular attention to cords at plugs convenience receptacles and the point where they exit from the appliance 13 Cleaning Unplug this unit from the wall outlet before cleaning Do not use liquid cleaners or aerosol cleaners Use a damp cloth for cleaning 14 Pow
12. contained in this manual meets FCC requirements Modifications not expressly approved by Vocopro may void your authority granted by the FCC to use this product 2 IMPORTANT When connecting this product to accessories and or another product use only high quality shielded cables Cable s supplied with this product MUST be used Follow all installation instructions Failure to follow instructions could void your FCC authorization to use this product in the U S A 3 NOTE This product has been tested and found to comply with the requirements listed in FCC Regulations Part 15 for Class B digital devices Compliance with these requirements provides a reasonable level of assurances that your use of this product in a residential environment will not result in harmful interference with other electronic devices This equipment generates uses radio frequencies and if not installed and used according to the instructions found in the owner s manual may cause interference harmful to the operation of other electronic devices Compliance with FCC regulations does not guarantee that interference will not occur in all installations If this product is found to be the source of interference which can be determined by turning the unit Off and On please try to eliminate the problem by using one of the following measures Relocate either this product or the device that is being affected by the interference Use power outlets that are on differ
13. e overall sound quality Refer to the instructions below when con necting your CDR 1000 PRO NOTE There are three options for inputting audio to the CDR 1000 PRO Balanced XLR Analog Unbalanced RCA Analog Digital Coaxial Digital NOTE The CDR 1000 PRO needs to be in ANALOG mode if using either XLR or RCA and in DIGITAL mode when using the Digital Coaxial input 1 Using Two Balanced XLR Cables and Connecting to the BALANCED XLR inputs NOTE The CDR 1000 PRO must in ANALOG mode 1 Connect the male end of each cable to the BALANCED left and right inputs on the rear panel of the CDR 1000 PRO 2 Connect the female end of each cable to the left and right outputs of your player or mixer CDR 1000 PRO OUTPUT ANALOG i n Peur BAL UNBAL BAL UNBAL CDR 1000 PRO Getting Connected cont ANALOG 1 0 INPUT CDR 1000 PRO OUTPUT INPUT DVX 880 PRO NOTE The CDR 1000 PRO must be in ANALOG mode e Go NOTE The CDR 1000 PRO must be DIGITAL mode 2 Using two RCA red and white Cables and Connecting to the UNBALANCED RCA inputs 1 Connect an end of each cable to the UNBALANCED left and right inputs on the rear panel of the CDR 1000 PRO 2 Connect the other end of each cable to the left and right outputs of your player mixer or amp GIG M
14. ent branch circuit breaker or fuse circuits or install AC line filter s In the case of radio or TV interference relocate reorient the antenna If the antenna lead in is 300 ohm ribbon lead change the lead in to coaxial type cable If these corrective measures do not produce satisfactory results please contact your local retailer authorized to distribute Vocopro products If you can not locate the appropriate retailer please contact Vocopro 1728 Curtiss Court La Verne CA 91750 CAUTION The apparatus is not disconnected from the AC power Source so long as it is connected to the wall outlet even if the apparatus itself is turned off To fully insure that the apparatus is indeed fully void if residual power leave unit disconnected from the AC outlet for at least fifteen seconds CAUTION READ THIS BEFORE OPERATING YOUR UNIT 1 To ensure the finest performance please read this manual carefully Keep it in a safe place for future reference 2 Install your unit in a cool dry clean place away from windows heat sources and too much vibration dust moisture or cold Avoid sources of hum transformers v motors To prevent fire or electrical shock do not expose to rain and water 3 Do not operate the unit upside down 4 Never open the cabinet If a foreign object drops into the Set contact your dealer 5 Place the unit in a location with adequate air circulation Do not interfere with its proper ventilation th
15. er lines An outdoor antenna should be located away from power lines 15 Nonuse Periods The power cord of the appliance should be unplugged from the outlet when left unused for a long period of time 16 Object and Liquid Entry Care should be taken so that objects do not fall and liquids are not spilled into the enclosure through openings 17 Damage Requiring Service The appliance should be serviced by qualified service personnel when The power supply cord or plug has been damaged or Objects have fallen into the appliance or The appliance has been exposed to rain or The appliance does not appear to operate normally or exhibits a marked change in performance or The appliance has been dropped or the enclosure damaged m OOU 18 Servicing The user should not attempt to service the appliance beyond that described in the operating instructions All other servicing should be referred to qualified service personnel Note To CATV system installer s U S A This reminder is provided to call the CATV system installer s attention to Article 820 40 of the NEC that provides guidelines for proper grounding and in particular specifies that the cable ground shall be connected as close to the point of cable entry as practical FCC INFORMATION U S A 1 IMPORTANT NOTICE DO NOT MODIFY THIS UNIT This product when installed as indicated in the instructions
16. is will cause the internal temperature to rise and may result in a failure 6 Do not use force on switches knobs or cords When moving the unit first turn the unit off Then gently disconnect the power plug and the cords connecting to other equipment Never pull the cord itself 7 Do not attempt to clean the unit with chemical solvents this might damage the finish Use a clean dry cloth 8 Be sure to read the Troubleshooting section on common operating errors before concluding that your unit is faulty 9 This unit consumes a fair amount of power even when the power switch is turned off We recommend that you unplug the power cord from the wall outlet if the unit is not going to be used for a long time This will save electricity and help prevent fire hazards To disconnect the cord pull it out by grasping the plug Never pull the cord itself 10 To prevent lightning damage pull out the power cord and remove the antenna cable during an electrical storm 11 The general digital signals may interfere with other equipment such as tuners or receivers Move the system farther away from such equipment if interference is observed NOTE Please check the copyright laws in your country before recording from records compact discs radio etc Recording of copyrighted material may infringe copyright laws NGEN D 2 ULTIMATE CHOICE OF KARAOKE ENTERTAINMENT Welcome And Thank you for purchasing the CDR 1000 PRO fr
17. olume meter stay around the middle Make sure the disc has been FINALIZED See instruc tions on finalizing a disc in the Operations section of this manual The disc you ve inserted is corrupted or not compatible with the CDR 1000 PRO Use a different disc or a differ ent brand of disc The disc is not compatible or damaged e It is a DVD disc CDR 1000 PRO does not read DVD discs 7 7 ULTIMATE CHOICE OF KARAOKE ENTERTAINMENT Vocopro 2005 V 1 1 W WW VOCOPRO COM
18. om VocoPro your ultimate choice in Karaoke entertainment With years of experience in the music entertainment business VocoPro is a leading manufacturer of Karaoke equipment and has been providing patrons of bars churches schools clubs and individual consumers the opportunity to sound like a star with full scale club models in home systems and mobile units All our products offer solid performance and sound reliability and to further strengthen our commitment to customer satisfaction we have customer service and technical support professionals ready to assist you with your needs We have provided some contact information for you below VocoPro 1728 Curtiss Court La Verne CA 91750 Toll Free 800 678 5348 TEL 909 593 8893 FAX 909 593 8890 VocoPro Company Email Directory Customer Service amp General Information info vocopro com Tech Support techsupport vocopro com Remember Our Website Be sure to visit the VocoPro website www vocopro com for the latest information on new products packages and promos And while you re there don t forget to check out our Club VocoPro for Karaoke news and events chat rooms club directories and even a Service directory We look forward to hearing you sound like a PRO with VocoPro your ultimate choice in Karaoke entertainment FOR YOUR RECORDS Please record the model number and serial number below for easy reference in case of loss or theft These numbers are located on the rea
19. on 2 To begin recording press the START button The LCD display will say RECORDING and show the track num ber along with the elapsed recording time 3 To stop recording press the CANCEL button This will also cause you to exit Record Mode CDR 1000 PRO CDR 1000 PRO MICI ET xz 02 Recording 06 25 Audio A 01 Input Rnalog 04 12 Audio NOTE For optimum recording quality be sure that the recording volume level is neither too high nor too low Refer to the input volume meter when adjusting recording volume If the orange bars at the top light up then the input level is too loud and it could cause distortion on the recording Pausing Recording To pause recording 1 While a disc is recording press the PLAY PAUSE button The LCD display will say PAUSE 2 To resume recording press the PLAY PAUSE button while the recording process is paused The LCD display will say RECORDING Creating Tracks on a Disc On music CDs each song is on a different track The CDR 1000 PRO allows you to easily create these tracks on a disc so that you can jump to a certain song To create a track 1 While the disc is already recording press the RECORD button 2 Recording will pause for 5 seconds 3 The track number will change and the disc will begin recording on a new track CDR 1000 PRO VALID 02 Recording 06 25 Audio A
20. otector power strip is plugged in and turned on Press the record button to switch the CDG 1000 PRO to recording mode The input audio can only be heard when the CDG 1000 PRO is in recording mode sure the audio ins and outs are connected prop erly f using the Analog RCA inputs be sure the CDR 1000 PRO is in ANALOG mode and if using the DIGITAL input make sure it is in DIGITAL mode f the disc is finalized it cannot be recorded on Put in a blank or non Finalized disc for recording This happens if you try to ERASE a CD R The ERASE function only works on CD Rewritables CD RWs The recording volume may have been set too high Try re recording and adjust the recording volume so that the bars on the Input Volume meter do not reach the orange bars Make sure you are connected to the Digital input The Analog input does not support 8cm discs Most standard CD players Car audio home audio etc do not support CD RW discs If using CD RW discs make sure that your CD player specifies that it is CD RW compatible 12 Troubleshooting Problem The final recording is not loud enough The disc will not play in other disc players The LED display says UNKNOWN The LCD display says DISC when there is a disc is in the disc tray Solution The recording volume may have been set too low Try re recording and adjust the recording volume so that the bars on the Input V
21. outputs on the rear panel of the CDR 1000 PRO 2 Connect the male end of each cable to the left and right XLR inputs of your mixer or amp 2 Using two RCA red and white Cables and Connecting to the UNBALANCED RCA inputs 1 Connect one end of each cable to the UNBALANCED left and right RCA outputs on the rear panel of the CDR 1000 PRO 2 Connect the other end of each cable to the left and right RCA inputs of your player mixer or All In One system BECA IET CDR 1000 PRO INPUT OO tine NOTE Match up the colors of the cables to the colors of the inputs White into white and red into red Controls and Functions Front Panel Controls and Functions NAOC TO 1 DISC tray Insert discs here Open and close the disc tray using the EJECT button 2 LED DISPLAY Displays information regarding the CDR 1000 PRO s operating status 3 INPUT VOLUME meter Displays the volume level that is being input for recording Use the RECORD LEVEL control to keep the volume from peaking or from being too low The volume is peaking when the orange bars at the top of the meter are lit For best results the meter should remain in the middle Doing so should prevent unwanted distortion which is present when the recording level is too loud If it is too low the recording will be difficult to hear when played back 4 EJECT EJE
22. r panel of the unit Space is also provided for other relevant information Model Number Serial Number Date of Purchase Place of Purchase Listening For A Lifetime Selecting fine audio equipment such as the unit you ve just purchased is only the start of your musical enjoyment Now it s time to consider how you can maximize the fun and excitement your equipment offers VocoPro and the Electronic Industries Association s Consumer Electronics Group want you to get the most out of your equipment by playing it at a safe level One that lets the sound come through loud and clear without annoying blaring or distortion and most importantly without affecting your sensitive hearing Sound can be deceiving Over time your hearing comfort level adapts to a higher volume of sound So what sounds normal can actually be loud and harmful to your hearing Guard against this by setting your equipment at a safe level BEFORE your hearing adapts To establish a safe level Start your volume control at a low setting Slowly increase the sound until you can hear it comfortably and clearly and without distortion Once you have established a comfortable sound level Set the dial and leave it there Pay attention to the different levels in various recordings Taking a minute to do this now will help to prevent hearing damage or loss in the future After all we want you listening for a lifetime Used wisely your new sound
23. stereo audio using Left and Right red and white RCA cables CDR 1000 PRO must be in Analog mode 3 BALANCED XLR outputs Use these to output stereo audio using a pair balanced XLR cables 4 UNBALANCED RCA outputs Use these to output stereo audio using Left and Right red and white RCA cables 5 DIGITAL INPUT Connect a player using a digital coaxial connection CDR 1000 PRO must be in Digital mode Compatible with 44 1 kHz digital signal 8 AC IN terminal Connect AC main power cord from the wall outlet to this terminal Operations Choosing Playback Mode or Record Mode When you first turn on the CDR 1000 PRO it will be in Playback Mode Before you can begin recording it must be in Record Mode Press the RECORD button to enter into Record Mode and follow the operating instructions in this manual Press the CANCEL button to exit Record Mode and return to Playback Mode NOTE Music from your audio input source cannot be heard when the CDG 1000 PRO is in Playback Mode CDR 1000 PRO Preparing a Disc for Playback Turn the power on by switching the POWER button on the front panel to the ON position Press the EJECT button on the front panel to open the disc tray Insert a disc data side down into the round recess in the tray NOTE Be sure that your disc is clean and in good shape for playback Excessive dust scratches markings etc could prevent normal disc playback Playing a Disc
Download Pdf Manuals
Related Search