EverFocus EPTZ3100 surveillance camera
Contents
1. Note In order to protect the bulb from dirt and scrape please put on the gloves before installing the bulb 8 Turn on the power and start to operate the EPTZ3000I 2 24 2 5 Accessories 2 5 1 EPTZ CPMA Ceiling Pendant Mount Adapter The pole mount is used for installing a speed dome on the ceiling indoors or outdoors The extension poles are available for the pole mount 2 5 2 EPTZ PMA Pole Mount Adapter The pole adapter is used for installing a wall mount bracket to a pole indoors or outdoors 2 5 3 EPTZ CMA Corner Mount Adapter 2 25 The corner mount are used for installing a wall mount bracket to a 270 corner of walls indoors or outdoors 2 26 3 EPTZ3000 EPTZ3000 1 CAMERA SETUP MENU In this section setup and operation guide of EPTZ3000 EPTZ3000I will be introduced There are 25 items of the setting menu However there is only one line on the line display so using some combination keys to operate is necessary 3 1 Structure of the Setup Menu MENU Press Press Shift ltems to enter camera setup menu 1 CAM ID 2 DZOOM 3 FOCUS 4 RIS 5 DAY NIGHT 6 S SHUTTER 7 DISPLAY 8 WBC MODE 9 TITLE DISP 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 ALM INT ALM IN2 ALM IN3 ALM IN4 ALM IN PRIO ALM OUT WDR SHUTTER AGC DNR PRIVATE ZONE AUTO REGRESS MOTION TOUR X CNT2. MIS im DB Olle im DI 177 212 214 220 222 223 211 2 16 179 2 3 2 Communication Protocol Setting The 1 2 and 3 bits of the SW2 are used to set communication protocol The factory default protocol is EVF PELCO D EVF AUTO Seep PELCO P A TYPE Protocol Baud Rate Terminal Resistance Notice Please make sure the power is off before setting and restart the EPTZ3000 EPTZ3000I to enable a new value after changing Set all of protocol switches to ON the speed EPTZ3000 EPTZ3000I will enter a self test mode 2 3 3 Transmission Speed Setting Baud Rate Setting The 4 and 5 bits of the SW2 on the PCB board are used to set the Baud Rate The default baud rate setting is 9600 9600 BPS 4800 BPS 2400BPS 1200 BPS Protocol Baud Rate Terminal Resistance 2 17 Notice Please make sure the power is off before setting and restart the EPTZSOOO EPTZ3000I to enable a new value after changing 2 18 2 4 Rack and Speed Dome Installation 2 4 1 Installation Requirements 1 Installation should be handled by a qualified service agent and should comply with all local regulations Service personnel should expect potential problems such as surface strength surface material falling objects outer breaches building vibration or other similar conditions 2 Check for all necessary materials and ensure if the selected installation loc
3. 122 F Focus Control One push Auto Manual Horizontal Rotation Speed 0 1 s 360 s 1 239 grade shift gears Horizontal Rotation Range 360 unlimited rotation Tilt Rotation Range 180 pendulum motion Auto Zoom Speed Control Control speed auto adjusted according to zoom length changing Auto Pan 2 Points Scanning Can set freely Auto Pan Speed 1 239 grades available 1 5 Dwell Time 2 points 1 239 seconds available Preset Positions 192 positions Running to Position Speed 1 239 grades available Dwell Time at Preset Position 1 239 seconds available Tour 16 groups Tour Point per Group 16 preset positions Fan amp Heater Fan amp Heater auto starts No Position Accuracy 0 1 Alarm 4 in 1 out with tour position auto triggering Built in Menu for Yes Functions Communication RS 485 Communication Speed 1200 2400 4800 9600 bps Built in Protocols Auto EVF Plus D A Type Pelco D Pelco P Address Editable Yes through DIP switch Speed Dome Address 0 255 Manual Pan Tilt Speed Pan 0 01 180 s Tilt 0 01 180 s Weatherproof Ratings IP66 Indoor Safety CE FCC Dimensions 218 5mm W x 267 5mm H 208 5mm W x 221 6mm H Weight 8 6 W x 10 5 H 4 2kg 9 25lbs 8 2 W x 8 7 H 2 15kg 4 8lbs 1 6 1 3 Feature 1 3 1 Prof
4. Y CNT PO CNT LOAD DEFAULT EXIT MENU Joystick up down to change subentries and right left to change the setting OFF ON ONE PUSH AUTO MAN AUTO MAN AUTO DAY NIGHT x 4 x8 x12 x16 x32 x64 x128 OFF OFF ON AUTO OUTDOOR AUTO INDOOR ONE PUSH MAN 2000K MAN 3200K MAN 5100K OFF ON OFF N C N O NIGHT N O NIGHT N C OFF N C N O OFF N C N O OFF N C N O 1234 2341 3412 4123 OFF LATCH 3 5 10 20 30 60 SEG LOW MIDDLE HIGH OFF AUTO A FLK 1 60 1 160 1 250 1 1000 1 2500 1 10000 1 120000 X2 X4 X6 X8 OFF LOW MIDDLE HIGH OFF LOW MIDDLE HIGH OFF ON OFF ON OFF LIMIT ENT 0000000001 0000000006 0000000000 3 27 3 1 1 Camera Setup Menu Press Menu to enter camera setup menu Press Shift Joystick up down to change subentries and right left to change the setting 1 CAM ID The name assigned to the camera 2 DZOOM Digital zoom enable or disable ON Enable a digital zoom OFF Disable a digital zoom 3 FOCUS Focus type auto focus manual focus and one push focus are available AUTO Auto focus is enabled MAN Manual focus is enabled ONE PUSH Enable the one push trigger focus mode The focus lens holds the same position until the next trigger command is received This function prevents the wrong focus in dark This option is the default value 4 IRIS Iris type auto iris and m
5. disabled when entering to OSD menu mode HOME Mode The camera view will go back to the home position when there is no keyboard operation in a specific time The home position and the specific time can be set by pressing Set Homel If you set the time to 0 minute then the camera will go back to home if there is no keyboard operation in 5 seconds This is the minimum no action time for HOME mode Note If HOME function is enabled dome will go to home immediately after powering on 4 2 Auto Pan Mode gt Two point auto pan Press A Pan to enter the auto pan mode and then the system will ask you to enter the auto pan speed 1 239 Press Enter to start auto pan In order to set the two points press Set A Pan and then enter the dwell time 1 239 seconds of each point EPTZ3000 begins to pan from point A to point B clockwise 360 auto pan Press Shift to enter the 360 auto pan System will ask you to enter 360 auto pan speed 1 239 The camera will turn 360 automatically but 4 36 not tilt 4 3 Position Setting gt Focus ona preset position Press the number key and then press to focus on the number of preset position or you can press Position then enter the preset position number and then press Enter to focus on the number of preset position gt Preset a position Shift the Joystick to the position you
6. title display 10 ALM IN1 The status of input alarm 1 N O Enable a normal open alarm input N C Enable a normal close alarm input NIGHT N O Dome turns to Night mode if external contact open Dome turns to Day mode if external contact closed NIGHT N C Dome turns to Night mode if external contact closed Dome turns to Day mode if external contact open OFF Disable alarm input 11 ALM IN2 The status of input alarm 2 N O Enable a normal open alarm input N C Enable a normal close alarm input OFF Disable alarm input 12 ALM IN3 The status of input alarm 3 N O Enable a normal open alarm input N C Enable a normal close alarm input OFF Disable alarm input 13 ALM IN4 The status of input alarm 4 N O Enable a normal open alarm input N C Enable a normal close alarm input 3 30 OFF Disable alarm input 14 ALM IN PRIO The priority of alarms 1234 The alarm priority is 1 gt 2 gt 3 gt 4 2341 The alarm priority is 2 gt 3 gt 4 gt 1 3412 The alarm priority is 3 gt 4 gt 1 gt 2 4123 The alarm priority is 4 gt 1 gt 2 gt 3 15 ALM OUT Duration time of the alarm output OFF Disable alarm output 3 5 10 20 30 60 SEC select alarm output s duration time LATCH The alarm output will not stop until there is any operation on keyboard 16 WDR Wide Dynamic Range LOW Low wide dynamic range MIDDLE Middle wide dynamic range HIGH High wide dynamic ra
7. 6A of the tour that you previously set Press Enter to start running the tour Alternatively you could run the tour without entering MENU Press Position 97 to run the tour that you have previously set please be informed that this function is only valid for TOTA If you need to reset press IRIS of the keyboard to exit 24 X CNT X axis counter This counter counts the x axis movement and 1 is counted when the speed dome pans 360 25 Y CNT Y axis counter This counter counts the y axis movement and 1 is counted when the speed dome tilts 180 26 PO CNT Position counter This counter counts the go position times 1 is counted when speed dome goes to a position once 27 LOAD DEFAULT Load default setting Select this item and then press Enter to load default setting Press Clr Menu whenever you want to quit menu setting 28 EXIT To exit Select this item and then press Enter to quit setting Press Clr Menu whenever you want to quit menu setting 3 35 4 EPTZ3000 30001 FUNCTION SETUP AND OPERATION 4 1 Manual Control Mode gt Manual control Shift Joystick Up Down Left Right and turn it Clockwise Counterclockwise to control speed dome Use the control keys which are Zoom Focus and IRIS function keys on the keyboard to Zoom In Out focus N near F Far or IRIS Note Zoom In Out control keys will be
8. InstallatiON iese ee ee neeese 2 22 2 5 A CCOSSOMGS ee ek eb ee ei ek n ke be ke ke Si ie ke be ke ee bo 2 25 2 5 1 EPTZ CPMA Ceiling Pendant Mount Adapter sesse sesse esse 2 25 2 5 2 EPTZ PMA Pole Mount Adaptet ccccceeeeessseeeeceeeeeeeeeeeeees 2 25 2 5 3 EPTZ CMA Corner Mount Adaptet cccceeesssseeecceeeeeeeeeeeeees 2 25 1 1 3 EPTZ3OOU EPTZ3000I CAMERA SETUP MENU ees ee ee ees ees esse ee 3 27 3 1 Structure of the Setup Menu sssseeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeenseeeeneees 3 27 3 1 1 Camera Setup Menu issie ee Re 3 28 4 EPTZ3000 3000I FUNCTION SETUP AND OPERATION ese 4 36 4 1 Manual Control Mode esse ees ee ed ek N EE dk ke Ke Nee KG dek dood 4 36 4 2 Auto Pan Mode ie iese se Ese Ee Re WE Ede NR ee eks oge eN ee ee ewe Es in 4 36 4 3 Positi n Setting iss ee EE Nee ee ee N see Ee ee ase ee ge 4 37 4 4 OUI OCS EE EE E EE E 4 38 4 5 Alarm Link to a PoSItiOn TOUF civics ss ardvs sesse kende REEN KEN ER EN Ke ee de ewe 4 39 4 6 Other operations si AE EER EKS GR EER ORN ERKEN ER EK eN ER RGN GR Re 4 40 APPENDIX The Alarm VO Connection sesse ees RR EER EE RR RR ER ER EE 4 41 1 2 1 EPTZ3000 EPTZ30001 OVERVIEW 1 1 Introduction EPTZ3000 EPTZ3000I an intelligent high speed dome camera is ready to secure your property with its omni directional and exact monitoring A 30X optical and 8X digital zoom combining with a high perform
9. Night ICR mode is AUTO it cannot be controlled by preset position setting gt Set the parameter of a preset position Press Set Position to set the parameter of a preset position You can set the going to speed 1 239 dwell time 1 239 seconds and the title of the position Shift the joystick Right Left to change bits and shift the Joystick Up Down to change the alphanumeric characteristic The available alphanumeric characteristics are O 9 A Z amp anda space gt Delete a preset position Press Clr Position to delete a preset position The system will ask you to enter the position number that you would like to delete and then press Enter 4 4 Tour Mode In the tour mode you can set a tour for viewing There are 16 tours can be set and 16 preset positions in a tour gt One way tour Mode Press to enter the tour mode The system will ask you 4 38 to enter the tour number you would like to run and starts the tour after pressing Ente To preset a tour before running is necessary Preset a one way tour Press Set to preset a one way tour The system will ask you to enter preset position numbers The positions need to be preset After finish entering all positions press to quit and then press to save the tour gt To and fro tour mode Press Shift Tour to run a to and fro tour The system will ask y
10. PTZ3000 EPTZ3000I The two switches are used to set address protocol Baud Rate video format and terminal resistance 1 9 1 4 EPTZ3OOO EPTZ3000I Connection 110V AG al Sa i 24V AC 3 5A Adapter l BNC Video Out 1 0Vpp 0 2V 759 RS485 Tx RS485 Control Line RS485 Tx ee N EPTZ3000 nite EPTZ3000I Alarm 2 Alarm 3 i 4 ALARM INPUTS Alarm 4 GROUND ALARM OUTPUTS 1 5 EPTZ3000 EPTZ3000 Quick Operation Guide Work with EKB500 EPTZSOOO EPTZ3000I and EKB500 Keyboard can work together by using factory default setting You just need to connect cables by the following steps 1 Connect the RS 485 cable to EPTZ3000 EPTZ3000I and a keyboard EKB500 2 Connect a video cable from EPTZ3000 EPTZ3000 to a monitor 3 Connect the power to the EPTZ3000 EPTZ3000I and a keyboard EKB500 After the EPTZ3000 EPTZ3000I finishes the self test mode you can start to operate the EPTZ3000 EPTZ3000I via the keyboard To operate the EPTZ3000 EPTZ3000I 1 Shift the Joystick up down or right left to view from camera 2 Turn the top of the Joystick to zoom in out 3 Press Zoom In Out Focus F N and IRIS function keys to operate the EPTZ3000 EPTZ3000I 1 11 2 EPTZ3000 EPTZ3000 INSTALLATION 2 1 Packing List There are 3 boxes that are housing bulb and mechanical part with a camera module one wall mount b
11. Speed Dome EP T Z3000 EP T Z30001 USER MANUAL N z Table of Contents EPTZSOOO EPTZ3000I OVERVIEW esse ee ee ee ee ee sees EER RR RR RR RR eeee ee ee EE 1 3 1 1 Introductio n s misisse N ee aana eara Rn 1 3 1 2 Specifications sies KAREE SEGE RS GR N GN Ed ee Ge ke Rd ee dee ek WE ananasai 1 5 1 3 Feature EE RE EE 1 7 1 3 1 Profile of EETZAOOOEP TZSOOO ss ED EE ED N ee N Ee 1 7 1 3 2 EPTZ3000 EPTZ30001 Base Board sesse ee ese ee esse ee ee ee ee ee ee ee ee 1 8 1 3 3 EPTZ3000 EPTZ30001 Control Board sesse esse esse ese ee ee ee ee ee 1 9 1 4 EPTZ3000 EPTZ30001 Connection sesse eene ee ee RR Re RR RR Re ee RR RE 1 10 1 5 EPTZ3OOO EPTZ3000I Quick Operation Guide Work with EKB500 1 11 EPTZ3000 EPTZ30001 INSTALLATION ee ee ees ees see ee RR Re RR ee ek eeee ae 2 12 2 1 Packing Lists ed nss ede dn ed ne dd ne ei oe ve did ee dd we ed Ke 2 12 2 2 Gable DE te oe ER EE nananana dasdnda avisava sanaaa da duasa saadaan aueia 2 12 2 3 LE UST se EA A AE E E A A T 2 13 2 3 1 Address Setting Ee ee EE ED ee Ag ER Pe 2 14 2 3 2 Communication Protocol Setting RIESE EE ge Ee ESE 2 17 2 3 3 Transmission Speed Setting Baud Rate Setting see 2 17 2 4 Rack and Speed Dome Installation ccccssceseseeeeeeeeeeeeeeeeeeeeeeeeeeeees 2 19 2 4 1 Installation Reguirements ii iii RR 2 19 2 4 2 EPTZ3000 Dome Camera Wall Mount Installation 2 19 2 4 3 EPTZ3000I Dome Camera
12. ance chip makes captured images clear and vivid The other powerful camera functions EPTZ3000 EPTZ3000I equips with gt gt Vv Vv MV WV V Wide Dynamic makes objects clear in a high illumination background Vertical double density interline CCD with a slower shutter and true Day Night function Electronics flip no mechanical flip is necessary 520 color 570 B amp W TVL PAL NTSC image formats support Auto and fast focus increases the searching speed and precision Auto Iris adjusts the monitoring image to the best brightness White Balance function makes the shades of color more natural in different light conditions Color B amp W images auto switching to enhance the sensitivity in a low light condition or at night Private zone protects your privacy 1 3 Furthermore the micro control unit enables camera a nimble and exact movement from minimal 0 01 sec to maximal 360 sec It can go to every preset position in 1 second lt also has other advantages such as gt gt 192 preset positions are available 16 cruise tours can be set and each tour contains up to 16 positions Up to 256 speed domes can be supported on a RS 485 bus when all speed domes are controlled by keyboard EKB500 Auto heater and fan to fit all kinds of temperature outdoor models Built in 4 alarm inputs and 1 alarm output All of the features make the intelligent high speed dome camera works for a wide range and demanding appli
13. anical part to the two bolts on the base of the housing and twist the mechanical part clockwise a little bit in order to engage it with the base Screw the two bolts on the base and then connect and fix the connection bus to the PCB board on the mechanical part FEEL ee PS gt gla Note The camera module on the mechanical part is very sensitive Please be careful when installing this part 6 Remove the lens protection cover before installing the bulb Align the 3 bolt holes into the 3 housing bolt holes and screw three M3 bolts with the attached small screw driver to fix the bulb _ M3 Blot M3 Blot 2 21 Note In order to protect the bulb from dirt and scrape please put on the gloves before installing the bulb 7 Turn on the power and start to operate the EPTZ3000 Note When turning on the power EPTZ3000 will enter self inspection mode and carry out a self testing program After finishing self inspection you can start to operate the EPTZ3000 2 4 3 EPTZ3000I Dome Camera Installation 1 Take off the housing from the packing and take off the PCB board 4 bolts on it inside the housing 2 Cut the ceiling against the housing s shape with a saw The exact diameter for cutting circle is 202 mm It cannot exceed 213 mm because speed dome housing may across the ceiling without any support Please leave a profound space of 144 5 mm so that the housing can be perfect
14. anual iris are available AUTO Auto iris is enabled MAN Manual iris is enabled 5 Day Night IR cut setting AUTO Auto ICR mode is enabled IR cut filter will open automatically in low lux NIGHT IR cut filter is always open No IR cut for true day night model only DAY IR cut filter is always close 3 28 6 SSHUTTER Slow electrical shutter In order to enhance the view in the low lux environment slow shutter allows more light go through the shutter X4 4 time slow shutter X8 8 time slow shutter X12 12 time slow shutter X16 16 time slow shutter X32 32 time slow shutter X64 64 time slow shutter X128 128 time slow shutter OFF Disable auto slow shutter 7 DISPLAY Display the zoom multiple ON Display the zoom multiple OFF Disable the zoom multiple display 8 WBC MODE White balance control mode AUTO OUTDOOR Auto white balance compensation with wider range Default value AUTO INDOOR Auto white balance compensation ONE PUSH One Push Auto White Balance Mode MAN 2000K Manual white balance compensation in 2000K color temperature MAN 3200K Manual white balance compensation in 3200K color temperature MAN 5100K Manual white balance compensation in 5100K color temperature Note WEC setting will affect the wide dynamic range or other image performance To adjust a proper value is important 3 29 9 TITLE DISP Display the title ON Display the title OFF Disable the
15. ation is suitable for the EPTZ3000 EPTZ3000I 2 4 2 EPTZ3000 Dome Camera Wall Mount Installation Note Installation location that is a wall a pole or a ceiling needs to support above five times the total weight of the camera assembly about 16 kg to avoid shaken images and dropping 1 Set wall mount bracket on the wall Mark the center of the holes on the wall against the bracket holes Use a drill to make 4 holes that can be nailed 4 0 25 X 1 25 screws at the marks Note The length of the screws depends on the surface material The mentioned screws are used in the normal concrete surface 2 19 2 Thread the cable through the hole in the wall mount bracket and screw in 4 M8 nuts for mounting the bracket 3 Take off the housing from the packing and take off the PCB board 4 bolts on it inside the housing Thread the cable through the top of the housing Fix the housing on the wall mount bracket and screw in 3 M5 bolts Hex on the top of the bracket with the attached Hex Allen wrench to fix the housing gt Ee Oo O sa ED OR KS OOO J is Hl 4 Connect the cable connectors to the nodes on the PCB board and then fix the PCB board in the housing by screwing 4 bolts on it Note Please notice the polarity of control line The EPTZ3000 will not work if the polarity of control line is mis connected 2 20 5 Align the two screw holes on the bottom of mech
16. cation such as banks airports stations casinos streets of cities intelligent buildings and etc 1 4 1 2 Specifications Model EPTZ3000 outdoor EPTZ3000I indoor Pickup Device 1 4 Vertical double density interline CCD Video Format NTSC or PAL Scanning System NTSC 525 TV lines 60 fields sec PAL 625 TV lines 50 fields sec Picture Elements Horizontal Resolution 768 x 494 NTSC 752 x 582 PAL 520 TVL Color 570TVL B W Sensitivity S N Ratio 0 3 Lux F 1 6 Color 0 05 Lux F 1 6 B W Over 52dB Electronic Shutter 128x Slow Shutter ON 1 60 1 120 000 sec NTSC 128x Slow Shutter ON 1 50 1 120 000 sec PAL Digital Slow Shutter OFF 4x 8x 12x 16x 32x 64x 128x selectable Shutter Selection AUTO A FLK Manual x8 1 120000 selectable Lens Type 30x optical zoom f 3 3 mm wide to 99mm tele F1 6 to F3 2 Zoom Ratio 240x max 30x Optical and 8x Digital Zoom True Day Night Auto Manual ICR Black Light Comp No Auto Gain Control Auto Manual White Balance Auto Indoor Auto Outdoor One push Man 2000K 3200K 5100K selectable Video Output BNC 1 0Vp p 750hm Sync Mode Power Source Line Lock Internal Sync 24VAC Power Consumption 24VAC 18W Max without 24VAC 18W Max heater 18W 24VAC 66W Max with heater 70W Operating Temperature 40 C 50 40 F 122 F 0 C 50 C 32 F
17. d transmission speed have to be set consistently with the control device such as a keyboard or a DVR Notice Please make sure the power is off before setting and restart the EPTZ3000 EPTZ3000I to enable a new value after changing 2 13 2 3 1 Address Setting The address code of the EPTZ3000 EPTZ3000 should be set to correspond properly with a control device to control multiple dome cameras The address codes are made up by the dipswitch SW1 8 bits on the PCB board The 8 bits dipswitch indicates the binary coded of the address and there are 256 addresses can be selected 0 255 28 256 It also means that there are up to 256 dome cameras that can cascade on the RS 485 bus The dipswitch setting and the indicated address are represented in the following chart Note The factory default address is 1 Notice Please make sure the power is off before setting and restart the EPTZ3000 EPTZ3000I to enable a new value after changing 2 14 Address Switch Address Switch Address Switch Address Switch ON 95 Oo Er Ole Me Me Ma om m C Me Ms Me m 31 Oie OE Oie Me Me Me 2 15 Address Switch Address 193 194 196 198 199 203 Switch 171 Address Switch Address Switch 204 He mi Olle Ole His Hie m DI 172 206 He mi Olle Clie Ms Me Ma 174 207 He mi Olle Ole His Me Ma 175 209 Me mi Ee
18. for Auto Pan function When Motion is ON you can use Auto Pan function simply by pressing Shift A Pan of the keyboard according to A Pan position you have set OFF Motion limitation function is disabled LIMIT Press Enter first The message NOW LIMIT OFF shows up press Enter again The message CHANGE ON shows up press Enter to change To change the value back to OFF simply follow the same steps again If you need to reset press IRIS of the keyboard to exit 23 TOUR Tour setting or tour run option Press Enter first to enter tour mode Shift joystick to right and left lt gt shift SET or RUN option Shift the joystick up for returning to previous setting Press Enter to confirm For Tour setting Shift joystick to right and left lt gt for changing Set Numeral TO1A T16A then press Enter to confirm Shift joystick to right and left for selecting PRE Numeral position from 01 99 then press Enter to confirm Shift joystick up and down to adjust DWL dwell time from 0 99 sec then press Enter to confirm Shift joystick to right and left for adjusting speed 5 235 with an interval of 5 then press 3 34 Enter to confirm For Tour Run Shift joystick to right and left for selecting RUN NUM T01A T1
19. ile of EPTZ3000 EPTZ3000I EPTZ3000 Wall Mount Bracket M5 Bolt Hex x3 Base PCB board Control board NN Connection Bus Housing Power Cable Inner Housing BNC Cable ay RS485 Cable Ma Bolt x8 Mechanical Part Ee Camera Module Bub Power Cable Base PCB board PR BNC Cable Control board N Clip RS485 Cable Housing Connection Bus Ceiling ____ Mechanical Part saan A SS Camera Module 1 7 1 3 2 EPTZSOOO EPTZ3000I Base Board The base board that is on the bottom of the housing connects to power cable video cable control cable alarm cable fan and heater In order to connect to cables the board needs to be taken off and put back after finishing connecting to all cables The connectors of cable names are marked on the board in white text The details of the alarm connector JP5 are shown on the APPENDIX A For EPTZ3000 outdoor model JP1 JP3 and JP6 that are two pin connectors need to be taken off during installing JP1 and JP3 are connectors for heater and they can be switched JP6 is a fan controller connector that turns on off of the fan The 3 cables are too short to be connected to a wrong connector when putting them back o D 3S gt EPTZ3000I Baseboard 1 8 1 3 3 EPTZSOOU EPTZ3000I Control Board The PCB board with two dipswitches is the control board of E
20. ly inserted to the ceiling 3 Thread the cable through the screw and the hole on the top of the housing and tighten up the screw to fix the cable 4 Place the housing into the hole that you just made Fix the housing on the ceiling with two clips adjust the screws of clips to make the housing perfectly fit to the ceiling 5 Connect the cable connectors to the nodes on the base board and then fix the base board in the housing by screwing 4 bolts on it 2 22 Cut the ceiling 202 mm Oo 4 4 8 Sd00000 EE Bessssssel Oo Note Please notice the polarity of control line The EPTZ30001 will not work if the polarity of control line is mis connected 6 Align the two screw holes on the bottom of mechanical part to the two bolts on the base of the housing and twist the mechanical part clockwise a little bit in order to engage it with the base Screw the two bolts on the base and then connect and fix the connection bus to the PCB board on the mechanical part 2 23 Note The camera module on the mechanical part is very sensitive Please be careful when installing this part 7 Remove the lens protection cover before installing the bulb Screw the connection wire to the housing in order to prevent the bulb from being drop down Align the 2 buttons on the bulb base with the 2 buttons on the housing and push bulb base to clip the housing id ER Connection wire jt Button
21. nge OFF Disable wide dynamic range 17 SHUTTER Electrical shutter mode AUTO Auto electrical shutter A FLK Anti Flicker Camera will auto adjust the shutter to reduce the flicker caused by fluorescent light 1 60 NTSC and 1 50 PAL default manual shutter 1 160 1 160 sec shutter for both NTSC and PAL 1 250 1 250 sec shutter for both NTSC and PAL 3 31 1 1000 1 1000 sec shutter for both NTSC and PAL 1 2500 1 2500 sec shutter for both NTSC and PAL 1 10000 1 10000 sec shutter for both NTSC and PAL 1 120000 1 120000 sec shutter for both NTSC and PAL x2 two time default manual shutter x4 four time default manual shutter x6 six time default manual shutter x8 eight time default manual shutter 18 AGC Auto Gain Control OFF Auto Gain Control Off LOW Low Auto Gain Control MIDDLE Middle Auto Gain Control HIGH High Auto Gain Control Note AGC setting will affect the wide dynamic range or other image performance To adjust a proper value is important 19 DNR Dynamic Noise Reduction OFF Dynamic Noise Reduction Off LOW Low Dynamic Noise Reduction MIDDLE Middle Dynamic Noise Reduction HIGH High Dynamic Noise Reduction 20 PRIVATE ZONE Private zone masking ON Enable the private zone masking 3 32 OFF Disable the private zone masking Press Enter to enter private zone setup mode and the masking will turn into red You can set the masking size and position in the private zone setu
22. ou to enter the tour number you would like to run and starts the tour after pressing Enter To preset a tour before running it is necessary Note 1 The difference between the One way tour mode and To and fro tour mode is that the return modes are different For example There is a tour with 3 preset positions 1 2 and 3 The camera runs 1 2 38 1 2 8 in the One way tour mode and 1 2 38 2 1 in the To and fro tour mode Note 2 You could set a pattern tour Press Set Tour and input 0 press Enter Sway the joystick to record the entire tour Press Stop to stop recording tour To view this pattern tour simply press Tour and input tour number 0 4 5 Alarm Link to a Position Tour EPTZ3000 EPTZ3000I have 4 alarm inputs that can be set to link to a position or a tour when an alarm is triggered gt Setan alarm link Press F1 to set an alarm link Enter the alarm number and then press Enter Switch the Joystick up down to select a position or a tour enter a position or tour number and then press to confirm the alarm link setting If you set the position number to 99 the dome will do a 360 degree auto scan or 4 39 AB two point pan if limit is ON If you set the position number to 98 the dome will do a frame scan gt Delete an alarm link Press F1 to delete a link of alarm to position tour Note 1 Af
23. p mode In this mode you can press Shift 6 to increase masking horizontal size Shift 4 to decrease masking horizontal size Shift 2 to increase masking vertical size Shift to decrease masking vertical size Shift Joystick to select the position where the masking is located Enter to confirm the size and position and then the masking will turn into green again If you use Pelco protocol keyboard command of private zone setting will be different Press IRIS to enter private zone setup mode and the masking will turn into red You can set the masking size and position in the private zone setup mode In this mode you can press Focus F to decrease masking size Focus N to increase masking size IRIS to switch the mask horizontal or vertical direction Shift Joystick to select the position where the masking is located IRIS to confirm the size and position and then the masking will turn into green again 3 33 21 AUTO REGRESS Auto regress to the shortest path during set a position It can shorten the response delay and increase the response performance and speed dome lifetime ON Enable the auto regress function OFF Disable the auto regress function 22 MOTION This is used to set a limitation
24. racket one power adapter and one tool packet in the package The detail accessories list below gt gt gt gt gt gt Housing x1 Bulb x1 Mechanical part with a camera module x1 Wall mount bracket x1 Adapter x1 Tool packet Glove x2 M5 Hex Allen wrench x1 Pin connector x1 M5 screw Hex x3 for wall mount bracket fixing gt M3 screw x3 for bulb fixing 2 2 Cable Needed Power Cable An adapter with 24V AC 3 5A output provides the power to the EPTZ3000 EPTZ3000I An extension power line may be needed Note The input AC voltage range of an adapter depends on different area Please make sure the voltage range before installing 2 12 Video Cable A BNC cable is used for connecting an EPTZ3000 EPTZ30001 to a DVR or a monitor An amplifier may be needed if the video cable is too long Control Cable Basically EPTZ3OOO EPTZ3000I uses a differential pair to connect to other devices by cascading A cable that has low signal decline can be used as a control cable Alarm Cable An alarm cable is not included in the packing list A suitable wire that has low signal decline can be used as an alarm cable 2 3 Initial Setup Initial setup includes dome address communication protocol transmission speed video format and terminal resistance settings All of the settings should be confirmed before the dome is installed The control related setting that is address communication protocol an
25. s product is designed and manufactured with high quality materials and hergeste components which can be recycled and reused ponente i i Dieses Symbol be dis sposed ne separately from vali household elektronische Ger te waste Please dispose of this equipment at your local collection systems for used electrical and electronic product wir lel Please help us to conserve the environment we ive in 4 42 Europe Office Albert Einstein Strasse 1 D 46446 Emmerich Germany TEL 49 2822 9394 0 www everfocus de China Beijing Office Room B 05D 1 KESHI PLAZA Shangdi Information Industry Base Haidian District Beijing China 100085 TEL 86 10 62973336 37 38 39 FAX 86 10 62971423 www everfocus com cn Japan Office 1809 WBG MARIBU East 18F 2 6 Nakase Mihama ku Chiba city 261 7118 Japan TEL 81 43 212 8188 FAX 81 43 297 0081 www everfocus com Ihr EverFocus Produkt wurde entwickelt und estellt mit qualitativ hochwertigen Materialien e recycelt und wie verwendet wer eni danen deutet cers elektrische und Helfen Sie uns bitte die Umwelt zu erhalten in der ben EverFocus P N MW01G0070C Ver F
26. ter alarm output signal is terminated the speed dome will resume action or return to its original position Note 2 After powering on the speed dome it will detect alarm status automatically 4 6 Other Operations The EPTZ3000 EPTZ30001 can work with a DVR that has PTZ control functions and a matching protocol The available control functions depend on different DVRs The EPTZ3000 EPTZ3000I can work with a keyboard that has PTZ control functions and a matching protocol The available control functions depend on different keyboards 4 40 APPENDIX The Alarm I O Connection There are 4 alarm inputs and 1 alarm output available The alarm VO connector that is marked as JP5 is a nine pin connector lt is located on the PCB board of the housing JP5 1 is 9 1 Alarm Input 3 i 2 Ground 3 Alarm Input 2 K or 4 Alarm Input 1 5 Ground 6 Alarm Input 0 7 Normal Open N O 8 Common COM 9 Normal Close N C 4 41 EverFocus Electronics Corp Head Office 12F No 79 Sec 1 Shin Tai Wu Road Hsi Chih Taipei Taiwan TEL 886 2 26982334 FAX 886 2 26982380 www everfocus com tw USA L A Office 1801 Highland Ave Unit A Duarte CA 91010 U S A TEL 1 626 844 8888 FAX 1 626 844 8838 www everfocus com USA N Y Office 415 Oser Avenue Unit S Hauppauge NY 11788 Tel 631 436 5070 Fax 631 436 5027 www everfocus com Your EverFocu
27. would like to preset and then press Shift Position The system will ask you to enter the preset position number 1 192 and then press to save the position There are up to 192 positions can be preset Three specific preset positions can be set as follows 92 gt Set Left Limit Stop A position 93 gt Set Right Limit Stop B position 95 gt Enter Menu mode Use keyboard control keys to control OSD items Focus F to go downward Focus N to go upward IRIS go to previous setting and IRIS 4 to exit You can directly go to the following specific preset positions 33 gt Rotation of 180 degree 34 gt Go to Home position if Home Position is set by EVF Keyboard 96 gt Stop Scan 97 gt Start running tour 98 gt Frame scan 60 degree step Default speed is 32 It can be changed by EVF Keyboard Shift setting speed 4 37 Dwell time default is 2 sec It can be changed by EVF Keyboard Sel setting dwell time of A pos or B pos 99 gt Auto scan 360 degree Default speed is 32 It can be changed by EVF Keyboard Shift setting speed We can even set camera s ICR Day Night function with RS 485 command via keyboard How to do this Press Position 88 to link to Day mode or Position 89 to link to Night mode ICR AUTO message will be shown on the right bottom part of the screen If OSD Day
Download Pdf Manuals
Related Search