Digitus DN-60011-1 network switch
Contents
1. 16 24 Port Desktop amp Rack mountable Fast Ethernet Switch User Manual Certification FE FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help To assure continued compliance any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this equipment Example use only shielded interface cables when connecting to computer or2. peripheral devices FCC Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment This transmitter must not be co located or operating in conjunction with any other antenna or transmitter This equipment complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation Caution The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment Such modifications could void the user authority to operate the equipment Package Contents The following items should be found in your package 16 24 Port Desktop or Rack mountable Fast Ethernet Switch Power Adapter User Manual gt Rack Brackets gt Screws Make sure that the package contains above items If any of the above items is missing or damaged please contact the store you bought this product from Content 1 INTRODUCTION 1 1 PRODUCT OVERVIEW 1 2 MAIN FEATURES 1 3 STANDARDS 1 4 WORKING ENVIRONMENT 2 INSTALLATION 2 1 BEFORE INSTALLATION 2 2 INSTALLATION 2 3 CONNECTING THE 16 24 PoRT DESKTOP amp RACK MOUNTABLE FAST ETHERNET SWITCH TO YOUR NETWORK 2 4 LED INDICATORS 3 TROUBLESHOOTING onan 1 I
3. ON Plug and Play 1 3 Standards IEEE 802 3 10Base T IEEE 802 3u 100Base TX IEEE 802 3x Flow Control IEEE 802 3az VV V ON 1 4 Working Environment Temperature gt 0 to 40 C operating gt 40 70 C storage Humidity gt 10 to 90 non condensing operating gt 5 to 90 non condensing storage Power gt 100 240VAC 50 60Hz 2 Installation 2 1 Before Installation Take note of the following conditions before using your switch Install the 16 24 port desktop amp rack mountable fast Ethernet switch in a fairly cool and dry place See Working Environment for the acceptable operating temperature and humidity ranges gt Install the switch in a site free from strong electromagnetic sources vibration dust and direct sunlight gt Leave at least 10cm of space to both the left and right of the switch for ventilation gt Visually inspect the AC power jack and make sure the power adapter cord is securely connected gt Do not place items on top of switch 2 2 Installation Desktop or Shelf Installation When installing the switch on a desk or shelf the rubber feet included with the device should first be attached Attach these cushioning feet on the bottom at each corner of the device Allow enough ventilation space between the device and the objects around it gt Rack Installation The Switch can be mounted in an standard 1U rack space To install attach the mounting brackets one
4. et 2 The Link LED is not lit Make sure the network configuration of connecting device is correct and network card and drivers are installed correctly gt Check the cable connections gt sure the cable distance between the switch and other IEEE802 3 compatible network device does not exceed 100 meters 3 Performance is bad gt Check the status of Ethernet switching If Ethernet switching is set to full duplex on one device but a partner is set to half duplex then performance will be poor gt sure the cable between the switch and other IEEE802 3 compatible network device is Category 5 UTP or better 4 Some devices can t talk to other devices on the network Check status of the Link LEDs to make sure devices are linked Make sure that the devices network configurations are correct gt Reset the switch if needed
5. ntroduction 1 1 Product Overview The 16 24 Port Desktop amp Rack mountable Fast Ethernet Switch is designed to allow simultaneous transmission of multiple packets via an internal high speed data channel This means that it can partition a network more efficiently than bridges or routers in most environments This 16 24 Port Desktop amp Rack mountable Fast Ethernet Switch is a highly reliable network switch and is the ideal device for bridging Ethernet to Fast Ethernet work groups or networks Simple and cost effective it supports IEEE802 3 10Base T Ethernet and IEEE802 3u 100Base TX Fast Ethernet Designed specifically for connecting work group devices and desktops companies no longer have to invest in expensive and inflexible switches engineered primarily for backbone implementations Companies can deploy this scalable affordable switch that increases the aggregate bandwidth of the network by boosting throughput to the work groups that need it most 1 2 Main Features Compliant with IEEE802 3 10Base T Ethernet IEEE802 3u 100Base TX 16 24 port 10 100Mbps TX Auto Negotiation Ethernet Switch 3 2 4 8Gbps switching fabric capacity Full Half Duplex capability on each TX port Supports TP interface Auto MDIX function for auto TX RX swap IEEE802 3x flow control for full duplex back pressure function for VV VV ON V half duplex operation Supports up to 8K MAC addresses LED indicators for simple diagnostics Built in power supply VV ON
6. on each side and secure them with the screws provided Then use the screws provided with the rack to mount the Switch in the rack 2 3 Connecting the 16 24 Port Desktop amp Rack Mountable Fast Ethernet Switch to Your Network Description Function PWR Connect to power adapter provided with unit Don t use other power adapters as your switch could be damaged These ports support network speeds of 10Mbps or 100Mbps and can operate in half and full duplex transfer modes These ports also support automatic MDI MDIX detection 1X 16X 24X which gives the Switch true plug and play capabilities Just connect any network cable from a device to the switch and the switch will automatically detect the settings of the device and adjust itself accordingly 2 4 LED Indicators The LED Indicators will allow you to monitor diagnose and troubleshoot any potential problem with the switch connection or attached devices LED Function On Power on diti Off Power off ON Corresponding port connection normal LINK ACT Flashing ponding port data transmitting Off Corresponding port connection abnormal not connected 10 100M ON Corresponding port works at 100Mbps OFF Corresponding port works at 10Mbps 3 Troubleshooting 1 The Power LED is not lit gt Check if the AC power cord is well connected Try to unplug and plug back in the power cord to the switch or try another power outl
Download Pdf Manuals
Related Search