Home

Asrock A75 Pro4

1. ISRock A75 Pro4 User Manual Version 1 1 Published June 2011 Copyright 2011 ASRock INC All rights reserved Copyright Notice No part of this manual may be reproduced transcribed transmitted or translated in any language in any form or by any means except duplication of documentation by the purchaser for backup purpose without written consent of ASRock Inc Products and corporate names appearing in this manual may or may not be regis tered trademarks or copyrights of their respective companies and are used only for identi cation or explanation and to the owners bene t without intent to infringe Disclaimer Speci cations and information contained in this manual are furnished for informa tional use only and subject to change without notice and should not be constructed as a commitment by ASRock ASRock assumes no responsibility for any errors or omissions that may appear in this manual With respect to the contents of this manual ASRock does not provide warranty of any kind either expressed or implied including but not limited to the implied warran ties or conditions of merchantability or tness for a particular purpose In no event shall ASRock its directors of cers employees or agents be liable for any indirect special incidental or consequential damages including damages for loss of pro ts loss of business loss of data interruption of business and the like even if ASRock has been advised of the possib
2. PLED PLED PLED Chassis and Power Fan Connectors 4 pin CHA FAN1 see p 12 No 22 3 pin CHA FAN2 see p 12 No 41 3 pin CHA FAN3 see p 12 No 42 3 pin PWR FAN1 see p 12 No 1 CHA FAN SPEED 12V GND FAN SPEED CONTROL PAR FAN SPEED 33 power LED to this header to indicate system power status The LED is on when the system is operating The LED keeps blinking in S1 state The LED is off in S3 S4 state or S5 state power off Please connect the fan cables to the fan connectors and match the black wire to the ground pin CHA FAN1 2 3 fan speed can be controlled through UEFI or AXTU CPU Fan Connectors FAN_SPEED_CONTROL Please connect the CPU fan CPU FAN SPEED 4 pin CPU FAN1 p cable to the connector and see p 12 No 5 pes match the black wire to the Toa A ground pin 4 Though this motherboard provides 4 Pin CPU fan Quiet Fan support the 3 Pin Y CPU fan still can work successfully even without the fan speed control function If you plan to connect the 3 Pin CPU fan to the CPU fan connector on this motherboard please connect it to Pin 1 3 Pin 1 3 Connected LE 3 Pin Fan Installation 3 pin CPU FAN2 GND 12V CPU FAN SPEED see p 12 No 6 B _ ATX Power Connector 12 mA Please connect an ATX power 24 pin ATXPWR1 see p 12 No 9 supply to this connector 1 A Though this motherboard provides 24 pin ATX power connector it can stil
3. Vista Vista 64 bit OS on your system 47 3 UEFI SETUP UTILITY 3 1 Introduction This section explains how to use the UEFI SETUP UTILITY to con gure your SYS tem The SPI Memory on the motherboard stores the UEFI SETUP UTILITY You may run the UEFI SETUP UTILITY when you start up the computer Please press lt F2 gt or lt Del gt during the Power On Self Test POST to enter the UEFI SETUP UTILITY otherwise POST will continue with its test routines If you wish to enter the UEFI SETUP UTILITY after POST restart the system by pressing lt Ctl gt lt Alt gt lt Delete gt or by pressing the reset button on the system chassis You may also restart by turning the system off and then back on Because the UEFI software is constantly being updated the following UEFI setup screens and descriptions are for reference purpose only and they may not exactly match what you see on your screen 3 1 1 UEFI Menu Bar The top of the screen has a menu bar with the following selections Main To set up the system time date information OC Tweaker To set up overclocking features Advanced To set up the advanced UEFI features H W Monitor To display current hardware status Boot To set up the default system device to locate and load the Operating System Security To set up the security features Exit To exit the current screen or the UEFI SETUP UTILITY Use lt gt key or lt gt key to choose among the selections on
4. Write to Read Delay tWTR Use this item to change Write to Read Delay tWTR Auto Manual setting The default is Auto Read to Precharge tRTP Use this item to change Read to Precharge tRTP Auto Manual setting The default is Auto Four Activate Window tFAW Use this item to change Four Activate Window tFAW Auto Manual setting The default is Auto Voltage Control DRAM Voltage Use this to select DRAM Voltage The default value is Auto APU PCIE Voltage VDDP Use this to select APU PCIE Voltage VDDP The default value is Auto APU DRAM PHY Voltage VDDR Use this to select APU DRAM PHY Voltage VDDR The default value is Auto CPU Load Line Calibration CPU Load Line Calibration helps prevent CPU voltage droop when the system is under heavy load SB Voltage Use this to select SB Voltage The default value is Auto Would you like to save current setting user defaults In this option you are allowed to load and save three user defaults according to your own requirements 52 3 4 Advanced Screen In this section you may set the con gurations for the following items CPU Con gu ration Nouth Bridge Con guration South Bridge Con guration Storage Con gura tion Super IO Con guration ACPI Con guration and USB Con guration ASROCK UEFI SETUP UTILITY TOMORROW S TECHNOLOGY TODAY Setting wrong values in this section may cause the system to malfunction Instant Flash Instant Flash is a UEFI ash utility
5. STEP 3 Install Windows XP XP 64 bit OS on your system You can start to install Windows XP XP 64 bit OS on your system At the begin ning of Windows setup press F6 to install a third party AHCI driver When prompt ed insert the SATA3 driver diskette containing the AMD AHCI driver After reading the oppy disk the driver will be presented Select the driver to install according to the OS you install Using SATA3 HDDs without NCQ and Hot Plug functions IDE mode STEP 1 Set up UEFI A Enter UEFI SETUP UTILITY Advanced screen Storage Con guration B Set the SATA Mode option to IDE STEP 2 Install Windows XP XP 64 bit OS on your system 46 2 18 2 Installing Windows 7 7 64 bit Vista Vista 64 bit Without RAID Functions If you want to install Windows 7 7 64 bit Vista Vista 64 bit on your SATA3 HDDs without RAID functions please follow below steps Using SATA3 HDDs with NCQ and Hot Plug functions AHCI mode STEP 1 Set up UEFI A Enter UEFI SETUP UTILITY Advanced screen Storage Con guration B Set the SATA Mode option to AHCI STEP 2 Install Windows 7 7 64 bit Vista Vista 64 bit OS on your system Using SATA3 HDDs without NCQ and Hot Plug functions IDE mode STEP 1 Set up UEFI A Enter UEFI SETUP UTILITY Advanced screen Storage Con guration B Set the SATA Mode option to IDE STEP 2 Install Windows 7 7 64 bit
6. also allows you to install four DDR3 DIMMs for dual channel con guration and please install identical DDR3 DIMMs in all four slots You may refer to the Dual Channel Memory Con guration Table below Dual Channel Memory Configurations DDR3 A1 DDR3 A2 DDR3 B1 DDR3 B2 Blue Slot White Slot Blue Slot White Slot 1 Populated Populated zy Popuated Poputated 3 Populated Populated Populated Populated Forthe con guration 3 please install identical DDR3 DIMMs in all four slots 1 If you want to install two memory modules for optimal compatibility 4 and reliability it is recommended to install them in the slots of the same color In other words install them either in the set of blue slots DDR3 A1 and DDR3_B1 or in the set of white slots DDR3_ A2 and DDR3 B2 2 If only one memory module or three memory modules are installed in the DDR3 DIMM slots on this motherboard it is unable to activate the Dual Channel Memory Technology 3 Ifa pair of memory modules is NOT installed in the same Dual Channel for example installing a pair of memory modules in DDR3 A1 and DDR3 A2 it is unable to activate the Dual Channel Memory Technology 4 It is not allowed to install a DDR or DDR2 memory module into DDR3 slot otherwise this motherboard and DIMM may be dam aged 5 If you adopt DDR3 2400 1866 1600 memory modules on this motherboard it is recommended to install them on DDR3 A2 and DDR3 B
7. three to six 6 Use Surround Display Click and drag the display icons to positions representing the physical setup of your monitors that you would like to use The placement of display icons determines how you move items from one monitor to another HDCP Function HDCP function is supported on this motherboard To use HDCP function with this motherboard you need to adopt the monitor that supports HDCP function as well Therefore you can enjoy the superior display quality with high de nition HDCP encryption contents Please refer to below instruction for more details about HDCP function What is HDCP HDCP stands for High Bandwidth Digital Content Protection a speci cation developed by Intel for protecting digital entertainment content that uses the DVI interface HDCP is a copy protection scheme to eliminate the possibility of intercepting digital data midstream between the video source or transmitter such as a computer DVD player or set top box and the digital display or receiver such as a monitor television or projector In other words HDCP speci cation is designed to protect the integrity of content as it is being transmitted Products compatible with the HDCP scheme such as DVD players satellite and cable HDTV set top boxes as well as few entertainment PCs requires a secure connection to a compliant display Due to the increase in manufacturers employing HDCP in their equipment it is highly recommended tha
8. 16 Driver Installation Guide To install the drivers to your system please insert the support CD to your optical drive rst Then the drivers compatible to your system can be auto detected and listed on the support CD driver page Please follow the order from up to bottom side to install those required drivers Therefore the drivers you install can work properly 2 17 Installing Windows 7 7 64 bit Vista Vista 64 bit XP XP 64 bit With RAID Functions If you want to install Windows 7 7 64 bit Vista Vista 64 bit XP XP 64 bit on a RAID disk composed of 2 or more SATA3 HDDs with RAID functions please follow below procedures according to the OS you install 2 17 1 Installing Windows XP XP 64 bit With RAID Functions If you want to install Windows XP XP 64 bit on a RAID disk composed of 2 or more SATA3 HDDs with RAID functions please follow below steps STEP 1 Set up UEFI A Enter UEFI SETUP UTILITY Advanced screen Storage Con guration B Set the SATA Mode option to RAID STEP 2 Make a SATA3 Driver Diskette Please use USB floppy or floppy disk A Insert the ASRock Support CD into your optical drive to boot your system B During POST at the beginning of system boot up press lt F11 gt key and then a window for boot devices selection appears Please select CD ROM as the boot device C When you see the message on the screen Generate Serial ATA driver diskette YN pres
9. Dual Monitor and Surround Display Features 26 2 8 ASRock Smart Remote Installation Guide 29 29 Jumpers SNP 30 2 10 Onboard Headers and Connectors rmmrerrrrrnrrrrervrrrnnerrerrrnnnnen 31 21T Sman SNE ed 36 22 DE SG am E on aus ST 2 13 Serial ATA3 SATA3 Hard Disks Installation 41 2 14 Hot Plug and Hot Swap Functions for SATA3 HDDS 41 2 15 SATA3 HDD Hot Plug and Hot SwapFeature and Operation Operation CITE cerner aer spat iR gen hips e dunes 42 2 16 Driver Installation Guide 2 82 rues d rb hte 44 2 17 Installing Windows 7 7 64 bit Vista Vista 64 bit XP XP 64 bit With RAID IF UnhcllOris uiuo ra ts cte itt ao etes 44 2 17 1 Installing Windows XP XP 64 bit With RAID FME 44 2 17 2 Installing Windows 7 7 64 bit Vista Vista 64 bit With RAID Functions 22 somuteS ee eben 45 2 18 Installing Windows 7 7 64 bit Vista Vista 64 bit XP XP 64 bit Without RAID Functions 46 2 18 1 Installing Windows XP XP 64 bit Without RAID ge EEE m 46 2 18 2 Installing Windows 7 7 64 bit Vista Vista 64 bit Without RAID Functions secos eerta o eet ire en ex 47 Contents 9 UEFLSETUP UN se 48 MON 48 VERT AB 48 3 1 2 NN Ek 49 32 Main STEN 49 3 3 OG Tweaker SCIG6h eet b re dex lenia eds 50 3 4 Advanced Screen DT Tm m m 53 3 4 1 CPU Con ODPSUOP eis e
10. Optical SPDIF Out Port 2 x Ready to Use USB 2 0 Ports 1 x eSATA3 Connector 4 x Ready to Use USB 3 0 Ports 1 X RJ 45 LAN Port with LED ACT LINK LED and SPEED LED 1 x IEEE 1394 Port 1 x Clear CMOS Switch with LED HD Audio Jack Rear Speaker Central Bass Line in Front Speaker Microphone see CAUTION 7 4 x USB 3 0 ports support USB 1 0 2 0 3 0 up to 5Gb s Connector 5 x SATA3 6 0Gb s connectors 1x IR header 1 x CIR header 1 x COM port header 1x HDMI SPDIF header 1x IEEE 1394 header 1 x Power LED header CPU Chassis Power FAN connector 24 pin ATX power connector SATA3 5 x SATA3 6 0 Gb s connectors support RAID RAID 0 RAID 1 and RAID 10 NCQ AHCI and Hot Plug functions 8 pin 12V power connector Front panel audio connector 3 x USB 2 0 headers support 6 USB 2 0 ports 1 x Dr Debug 7 Segment Debug LED 1 x Clear CMOS Switch with LED 1 x Power Switch with LED 1 x Reset Switch with LED BIOS Feature 32Mb AMI UEFI Legal BIOS with GUI support Supports Plug and Play ACPI 1 1 Compliance Wake Up Events Supports jumperfree SMBIOS 2 3 1 Support DRAM VDDP VDDR SB Voltage Multi adjustment Support CD Drivers Utilities AntiVirus Software Trial Version AMD Live Explorer AMD Fusion CyberLink MediaEspresso 6 5 Trial ASRock Software Suite CyberLink DVD Suite OEM and Trial Unique Feature ASRock Extreme Tuning Utility AXTU see CAUTI
11. With the internal VGA output sup port DVI D D Sub and HDMI you can easily enjoy the bene ts of dual monitor feature without installing any add on VGA card to this motherboard This mother board also provides independent display controllers for DVI D D Sub and HDMI to support dual VGA output so that DVI D D sub and HDMI can drive same or different display contents To enable dual monitor feature please follow the below steps 1 Connect DVI D monitor cable to DVI D port on the I O panel connect D Sub monitor cable to D Sub port on the I O panel or connect HDMI monitor cable to HDMI port on the I O panel D Sub port DVI D port HDMI port 2 If you have installed onboard VGA driver from our support CD to your system already you can freely enjoy the bene ts of dual monitor function after your system boots If you haven t installed onboard VGA driver yet please install onboard VGA driver from our support CD to your system and restart your computer 1 D Sub DVI D and HDMI monitors cannot be enabled at the same time You can only choose the combination DVI D HDMI or HDMI D Sub 2 When you playback HDCP protected video from Blu ray BD or HD DVD disc the content will be displayed only in one of the two monitors instead of both monitors 3 To support Dual link DVI monitor please do not use D Sub and HDMI ports Please connect the DVI monitor cable to the DVI port only 26 Surround Display Feature This motherb
12. embedded in Flash ROM This conve nient UEFI update tool allows you to update system UEFI without entering operating systems rst like MS DOS or Windows Just launch this tool and save the new UEFI le to your USB ash drive oppy disk or hard drive then you can update your UEFI only in a few clicks without prepar ing an additional oppy diskette or other complicated ash utility Please be noted that the USB ash drive or hard drive must use FAT32 16 12 le system If you execute Instant Flash utility the utility will show the UEFI les and their respective information Select the proper UEFI le to update your UEFI and reboot your system after UEFI update process completes 93 3 4 1 CPU Configuration ASROCK UEFI SETUP UTILITY TOMORROW S TECHNOLOGY TODAY Core C6 Mode Use this item to enable or disable Core C6 mode The default value is Disabled Package C6 Mode This item appears only when you enable the item Core C6 Mode Use this item to enable or disable Package C6 mode The default value is Dis abled Cool n Quiet Use this item to enable or disable AMD s Cool n Quiet technology The default value is Enabled Con guration options Enabled and Disabled If you install Windows 7 Vista and want to enable this function please set this item to Enabled Please note that enabling this function may re duce CPU voltage and memory frequency and lead to system stability or compatibility issue wit
13. some of ASRock motherboards Please refer to ASRock website for the motherboard support list http www asrock com 29 2 9 Jumpers Setup The illustration shows how jumpers are setup When the jumper cap is placed on pins the jumper is Short If no jumper cap F 4 is placed on pins the jumper is Open The illustration shows a 3 pin jumper whose MT eg EEE pint and pin2 are Short when jumper cap Short Open is placed on these 2 pins Jumper Setting Description Clear CMOS Jumper 12 2 3 CLRCMOS1 fe of om see p 12 No 10 Default Clear CMOS Note CLRCMOS1 allows you to clear the data in CMOS To clear and reset the system parameters to default setup please turn off the computer and unplug the power cord from the power supply After waiting for 15 seconds use a jumper cap to short pin2 and pin3 on CLRCMOS1 for 5 seconds However please do not clear the CMOS right after you update the BIOS If you need to clear the CMOS when you just nish updating the BIOS you must boot up the system rst and then shut it down before you do the clear CMOS ac tion Please be noted that the password date time user default pro le 1394 GUID and MAC address will be cleared only if the CMOS battery is removed The Clear CMOS Switch has the same function as the Clear CMOS jumper 30 2 10 Onboard Headers and Connectors Onboard headers and connectors are NOT jumpers Do NOT place jumper caps over these headers and c
14. the D Sub resolution and cause the display abnormal situation It is recom mended to use DVI or HDMI monitor to get better performance Spread Spectrum This item should always be Auto for better system stability AMD Turbo Core Technology This item appears only when the processor you adopt supports this fea ture Use this to select enable or disable AMD Turbo Core Technology Con guration options Auto and Disabled The default value is Auto Processor Maximum Frequency It will display Processor Maximum Frequency for reference Processor Maximum Voltage It will display Processor Maximum Voltage for reference Multiplier Voltage Change This item is set to Auto by default If it is set to Manual you may adjust the value of Processor Frequency and Processor Voltage However it is recommended to keep the default value for system stability CPU Frequency Multiplier For safety and system stability it is not recommended to adjust the value of this item 50 CPU Voltage It allows you to adjust the value of CPU voltage However for safety and system stability it is not recommended to adjust the value of this item DRAM Configuration DRAM Frequency If Auto is selected the motherboard will detect the memory module s inserted and assigns appropriate frequency automatically DRAM Timing Control ASROCK UEFI SETUP UTILITY R sep pee 5 ee 15000 ker a ry s es tS nn al EEE M TOM
15. this header according to the pin assignments below Note the positive and negative pins before connecting the cables PWRBTN Power Switch Connect to the power switch on the chassis front panel You may con gure the way to turn off your system using the power switch 32 Chassis Speaker Header 4 pin SPEAKER 1 see p 12 No 21 Power LED Header 3 pin PLED1 see p 12 No 24 RESET Reset Switch Connect to the reset switch on the chassis front panel Press the reset switch to restart the computer if the computer freezes and fails to per form a normal restart PLED System Power LED Connect to the power status indicator on the chassis front panel The LED is on when the system is operating The LED keeps blinking when the sys tem is in S1 sleep state The LED is off when the system is in S3 S4 sleep state or powered off S5 HDLED Hard Drive Activity LED Connect to the hard drive activity LED on the chassis front panel The LED is on when the hard drive is reading or writing data The front panel design may differ by chassis A front panel module mainly consists of power switch reset switch power LED hard drive activity LED speaker and etc When connecting your chassis front panel module to this header make sure the wire assignments and the pin assign ments are matched correctly SPEAKER DUMMY URAMAT HRY D U T T speaker to this header Please connect the chassis Please connect the chassis
16. your computer Then you will nd ATI Catalyst Control Center on your Windows taskbar Ghamn ri 4 CH 10 54 AM ATI Catalyst Control Center Double click ATI Catalyst Control Center Click View select CrossFi rex and then check the item Enable CrossFireX Select 2 GPUs and click Apply if you install two Radeon graphics cards l irm moneam etan in m anim Seem meis Pur es prap p hag ee eae Fn 22 Although you have selected the option Enable CrossFire the Cross FireX function may not work actually Your computer will automatically reboot After restarting your computer please con rm whether the option Enable CrossFire in ATI Catalyst Control Center is selected or not if not please select it again and then you are able to enjoy the bene t of CrossFireX feature Step 7 You can freely enjoy the bene t of CrossFireX or Quad CrossFirex feature CrossFireX appearing here is a registered trademark of AMD Technologies Inc and is used only for identi cation or explanation and to the owners bene t without intent to infringe For further information of AMD CrossFireX technology please check AMD website for updates and details 23 2 6 AMD Dual Graphics Operation Guide This motherboard supports AMD Dual Graphics feature AMD Dual Graphics brings multi GPU performance capabilities by enabling an AMD A75 FCH Hudson D3 integrated graphics pr
17. 2 slots 17 Installing a DIMM Fw j Please make sure to disconnect power supply before adding or removing DIMMs or the system components Step 1 Unlock a DIMM slot by pressing the retaining clips outward Step 2 Align a DIMM on the slot such that the notch on the DIMM matches the break on the slot z Y IX TEA FA a notch rp qWrpeTPPUI prTUY The DIMM only ts in one correct orientation It will cause permanent damage to the motherboard and the DIMM if you force the DIMM into the slot at incorrect orientation Step 3 Firmly insert the DIMM into the slot until the retaining clips at both ends fully snap back in place and the DIMM is properly seated 2 4 Expansion Slots PCI and PCI Express Slots There are 3 PCI slots and 4 PCI Express slots on this motherboard PCI Slots PCI slots are used to install expansion cards that have the 32 bit PCI interface PCIE Slots PCIE1 PCIE3 PCIE x1 slot White is used for PCI Express cards with x1 lane width cards such as Gigabit LAN card and SATA2 card PCIE2 PCIE x16 slot Blue is used for PCI Express x16 lane width graphics cards or used to install PCI Express graphics cards to support CrossFireX function PCIE4 PCIE x16 slot Blue is used for PCI Express x4 lane width cards or used to install PCI Express graphics cards to support CrossFireX function 1 In single VGA card mode it is recommended to install a PCI Ex press x16 gra
18. 2 x PCI Express 2 0 x16 slots PCIE2 x16 mode PCIE4 x4 mode 2 x PCI Express 2 0 x1 slots 3 x PCI slots Supports AMD Quad CrossFireX CrossFireX and Dual Graphics AMD Radeon HD 65XX 64XX graphics DirectX 11 Pixel Shader 5 0 Max shared memory 512MB see CAUTION 4 Three VGA Output options D Sub DVI D and HDMI see CAUTION 5 Supports HDMI 1 4a Technology with max resolution up to 1920x1200 60Hz Supports Dual link DVI with max resolution up to 2560x1600 75Hz Supports D Sub with max resolution up to 1920x1600 Q 60Hz Supports Auto Lip Sync Deep Color 12bpc xvYCC and HBR High Bit Rate Audio with HDMI Compliant HDMI monitor is required see CAUTION 6 Supports Blu ray Stereoscopic 3D with HDMI 1 4a Supports AMD Steady Video New video post processing capability for automatic jutter reduction on home online video Supports HDCP function with DVI and HDMI ports Supports Full HD 1080p Blu ray BD HD DVD playback with DVI and HDMI ports 7 1 CH HD Audio with Content Protection Realtek ALC892 Audio Codec Premium Blu ray audio support Supports THX TruStudio LAN PCIE x1 Gigabit LAN 10 100 1000 Mb s Realtek RTL8111E Supports Wake On LAN Supports LAN Cable Detection Supports Energy Ef cient Ethernet 802 3az Supports PXE Rear Panel I O I O Panel 1 x PS 2 Mouse Keyboard Port 1 x D Sub Port 1 x DVI D Port 1 x HDMI Port 1 x
19. 32 Front Panel IEEE 1394 Header Clear CMOS Jumper CLRCMOS1 FRONT 1394 White Southbridge Controller 33 Front Panel Audio Header HD AUDIO1 White SATA3 Connector SATA3 5 White 34 PCI Slot PCI3 SATA3 Connector SATA3 4 White 35 PCI Slot PCI2 SATA3 Connector SATA3 3 White 36 PCI Express 2 0 x16 Slot PCIE4 Blue SATA3 Connector SATA3 1 White 37 PCI Slot PCI1 SATA3 Connector SATA3 2 White 38 PCI Express 2 0 x1 Slot PCIE3 White Dr Debug LED 39 PCI Express 2 0 x16 Slot PCIE2 Blue Power Switch PWRBTN 40 PCI Express 2 0 x1 Slot PCIE1 White Reset Switch RSTBTN 41 Chassis Fan Connector CHA FAN2 System Panel Header PANEL1 White 42 Chassis Fan Connector CHA FAN3 Chassis Speaker Header SPEAKER 1 White 12 1 4 I O Panel ky 16 15 14 18 12 11 1 PS 2 Mouse Keyboard Port Green Purple 10 Microphone Pink 2 D Sub Port 11 USB 3 0 Ports USB01 3 USB 2 0 Ports USB23 12 IEEE 1394 Port IEEE 1394 4 LAN RJ 45 Port 13 eSATA3 Connector 5 Central Bass Orange 14 Clear CMOS Switch CLRCBTN 6 Rear Speaker Black 15 HDMI Port 7 Optical SPDIF Out Port 16 DVI D Port 8 Line In Light Blue 17 USB 3 0 Ports USB45 9 Front Speaker Lime It is recommended to install the USB Keyboard Mouse cable to USB 2 0 ports USB23 instead of USB 3 0 ports There are two LED next to the LAN port Please refer to the table below for the LAN port LED indications LAN Port LED Indications Descrip
20. 64 bit OS Right click the desktop choose Properties and select the Settings tab so that you can adjust the parameters of the multi monitor according to the steps below A Click the Identify button to display a large number on each monitor B Right click the display icon in the Display Properties dialog that you wish to be your primary monitor and then select Primary When you use multiple monitors with your card one monitor will always be Primary and all additional monitors will be designated as Secondary C Select the display icon identi ed by the number 2 D Click Extend my Windows desktop onto this monitor E Right click the display icon and select Attached if necessary F Set the Screen Resolution and Color Quality as appropriate for the second monitor Click Apply or OK to apply these new values G Repeat steps C through E for the diaplay icon identi ed by the number one to Six 27 For Windows 7 7 64 bit Vista Vista 64 bit OS Right click the desktop choose Personalize and select the Display Settings tab so that you can adjust the parameters of the multi monitor according to the steps below A Click the number 2 icon B Click the items This is my main monitor and Extend the desktop onto this monitor C Click OK to save your change D Repeat steps A through C for the display icon identi ed by the number
21. 66 1600MHz memory speed is supported depends on the CPU you adopt If you want to adopt DDR3 2400 1866 1600 memory module on this motherboard please refer to the memory support list on our website for the compatible memory modules ASRock website http Awww asrock com Due to the operating system limitation the actual memory size may be less than 4GB for the reservation for system usage under Windows 7 Vista XP For Windows 64 bit OS with 64 bit CPU there is no such limitation The maximum shared memory size is de ned by the chipset vendor and is subject to change Please check AMD website for the latest informa tion You can choose to use two of the three monitors only D Sub DVI D and HDMI monitors cannot be enabled at the same time Besides with the DVI to HDMI adapter the DVI D port can support the same features as HDMIport xvYCC and Deep Color are only supported under Windows 7 64 bit 7 Deep Color mode will be enabled only if the display supports 12bpc in EDID HBR is supported under Windows 7 64 bit 7 Vista 64 bit Vista For microphone input this motherboard supports both stereo and mono modes For audio output this motherboard supports 2 channel 4 chan nel 6 channel and 8 channel modes Please check the table on page 13 for proper connection ASRock Extreme Tuning Utility AXTU is an all in one tool to ne tune different system functions in a user friendly interface which is including Hard
22. IRQ3 and 2E8 IRQ3 58 3 4 6 ACPI Configuration ASROCK UEFI SETUP UTILITY 000 er es meme ER KE T 1 Ht a TOMORROW S TECHNOLOGY TODAY Suspend to RAM Use this item to select whether to auto detect or disable the Suspend to RAM feature Select Auto will enable this feature if the OS supports it Check Ready Bit Use this item to enable or disable the feature Check Ready Bit Restore on AC Power Loss This allows you to set the power state after an unexpected AC power loss If Power Off is selected the AC power remains off when the power re covers If Power On is selected the AC power resumes and the system starts to boot up when the power recovers PS 2 Keyboard Power On Use this item to enable or disable PS 2 keyboard to turn on the system from the power soft off mode PCI Devices Power On Use this item to enable or disable PCI devices to turn on the system from the power soft off mode Ring In Power On Use this item to enable or disable Ring In signals to turn on the system from the power soft off mode RTC Alarm Power On Use this item to enable or disable RTC Real Time Clock to power on the system USB Keyboard Remote Power On Use this item to enable or disable USB Keyboard Remote to power on the system USB Mouse Power On Use this item to enable or disable USB Mouse to power on the system 59 ACPI HPET table Use this item to enable or disable AC
23. ITY Advanced screen Storage Con guration B Set the SATA Mode option to RAID STEP 2 Use RAID Installation Guide to set RAID configuration Before you start to con gure RAID function you need to check the RAID installation guide in the Support CD for proper con guration Please refer to the BIOS RAID installation guide part of the document in the following path in the Support CD RAID Installation Guide STEP 3 Make a SATA3 Driver Diskette Make a SATA3 driver diskette by following section 2 17 1 step 2 on page 44 STEP 4 Install Windows 7 7 64 bit Vista Vista 64 bit OS on your system 45 2 18 Installing Windows 7 7 64 bit Vista Vista 64 bit XP XP 64 bit Without RAID Functions If you want to install Windows 7 7 64 bit Vista Vista 64 bit XP XP 64 bit OS on your SATA3 HDDs without RAID functions please follow below procedures according to the OS you install 2 18 1 Installing Windows XP XP 64 bit Without RAID Functions If you want to install Windows XP XP 64 bit on your SATA3 HDDs without RAID functions please follow below steps Using SATA3 HDDs with NCQ and Hot Plug functions AHCI mode STEP 1 Set up UEFI A Enter UEFI SETUP UTILITY Advanced screen Storage Con guration B Set the SATA Mode option to AHCI STEP 2 Make a SATA3 Driver Diskette Make a SATA3 driver diskette by following section 2 17 1 step 2 on page 44
24. ON 8 ASRock Instant Boot ASRock Instant Flash see CAUTION 9 ASRock APP Charger see CAUTION 10 ASRock SmartView see CAUTION 11 ASRock XFast USB see CAUTION 12 ASRock On Off Play Technology see CAUTION 13 Hybrid Booster ASRock U COP see CAUTION 14 Hardware CPU Temperature Sensing Monitor Chassis Temperature Sensing CPU Chassis Power Fan Tachometer CPU Chassis Quiet Fan CPU Chassis Fan Multi Speed Control Voltage Monitoring 12V 5V 3 3V Vcore Microsoft Windows 7 7 64 bit Vista Vista 64 bit XP SP3 XP 64 bit compliant Certifications FCC CE WHQL ErP EuP Ready ErP EuP ready power supply is required see CAUTION 15 For detailed product information please visit our website http www asrock com WARNING Please realize that there is a certain risk involved with overclocking including adjusting the setting in the BIOS applying Untied Overclocking Technology or using the third party over clocking tools Overclocking may affect your system stability or even cause damage to the components and devices of your system It should be done at your own risk and expense We are not responsible for possible damage caused by overclocking CAUTION ile This motherboard supports Dual Channel Memory Technology Before you implement Dual Channel Memory Technology make sure to read the installation guide of memory modules on page 17 for proper installation Whether 2400 18
25. ORROW S TECHNOLOGY TODAY Power Down Enable Use this item to enable or disable DDR power down mode Bank Interleaving Interleaving allows memory accesses to be spread out over banks on the same node or accross nodes decreasing access contention Channel Interleaving It allows you to enable Channel Memory Interleaving Con guration op tions Disabled Auto The default value is Auto CAS Latency tCL Use this item to change CAS Latency tCL Auto Manual setting The default is Auto RAS to CAS Delay tRCD Use this item to change RAS to CAS Delay tRCD Auto Manual setting The default is Auto Row Precharge Time tRP Use this item to change Row Precharge Time tRP Auto Manual setting The default is Auto RAS Active Time tRAS Use this item to change RAS Active Time tRAS Auto Manual setting The default is Auto ol Command Rate CR Use this item to change Command Rate CR Auto Manual setting Min 1T Max 2T The default is Auto RAS Cycle Time tRC Use this item to change RAS Cycle Time tRC Auto Manual setting The default is Auto Write Recovery Time tWR Use this item to change Write Recovery Time t WR Auto Manual setting The default is Auto Refresh Cyle Time tRFC Use this item to change Refresh Cyle Time tRFC Auto Manual setting The default is Auto RAS to RAS Delay tRRD Use this item to change RAS to RAS Delay tRRD Auto Manual setting The default is Auto
26. PI HPET Table The default value is Enabled Please set this option to Enabled if you plan to use this moth erboard to submit Windows Vista certi cation 60 3 4 7 USB Configuration ASROCK UEFI SETUP UTILITY TOMORROW S TECHNOLOGY TODAY USB 2 0 Controller Use this item to enable or disable the use of USB 2 0 controller USB 3 0 Controller Use this item to enable or disable the use of USB 3 0 controller Legacy USB Support Use this option to select legacy support for USB devices There are four con guration options Enabled Auto Disabled and UEFI Setup Only The default value is Enabled Please refer to below descriptions for the details of these four options Enabled Enables support for legacy USB Auto Enables legacy support if USB devices are connected Disabled USB devices are not allowed to use under legacy OS and UEFI setup when Disabled is selected If you have USB compatibility is sue it is recommended to select Disabled to enter OS UEFI Setup Only USB devices are allowed to use only under UEFI setup and Windows Linux OS Legacy USB 3 0 Support Use this option to enable or disable legacy support for USB 3 0 devices The default value is Enabled 61 3 5 Hardware Health Event Monitoring Screen In this section it allows you to monitor the status of the hardware on your system including the parameters of the CPU temperature motherboard temperature CPU fan speed chassis f
27. able onboard debug port LED The default value is Auto 56 3 4 4 Storage Configuration ASROCK UEFI SETUP UTILITY TOMORROW S TECHNOLOGY TODAY SATA Controller Use this item to enable or disable the SATA Controller feature SATA Mode Use this item to adjust SATA Mode The default value of this option is IDE Mode Con guration options AHCI Mode RAID Mode and IDE Mode If you set this item to RAID mode it is suggested to install SATA ODD driver on SATA3 5 and eSATA3 ports SATA IDE Combined Mode This item is for SATA3_5 and eSATA3 ports Use this item to enable or dis able SATA IDE combined mode The default value is Enabled If you want to build RAID on SATA3 5 and eSATA3 ports please disable this item Hard Disk S M A R T Use this item to enable or disable the S M A R T Self Monitoring Analy sis and Reporting Technology feature Con guration options Disabled Auto Enabled 57 3 4 5 Super IO Configuration ASROCK UEFI SETUP UTILITY Sl TOMORROW S TECHNOLOGY TODAY Serial Port Use this item to enable or disable the onboard serial port Serial Port Address Use this item to set the address for the onboard serial port Con guration options 3F8 IRQ4 and 3E8 IRQ4 Infrared Port Use this item to enable or disable the onboard infrared port Infrared Port Address Use this item to set the address for the onboard infrared port Con guration options 2F8
28. ader This header can be used to Ielololol 4 pin CIR1 open connect the remote IRRX see p 12 No 29 ATX 5VSB controller receiver Front Panel Audio Header D TNR This is an interface for the front MIC_RET 9 pin HD AUDIO1 OUT RET panel audio cable that allows see p 12 No 33 convenient connection and Beat control of audio devices J_SENSE OUT2 R MIC2 R MIC2 L 1 High De nition Audio supports Jack Sensing but the panel wire on the chassis must support HDA to function correctly Please follow the instruction in our manual and chassis manual to install your system 2 If you use AC 97 audio panel please install it to the front panel audio header as below A Connect Mic IN MIC to MIC2 L B Connect Audio R RIN to OUT2 R and Audio L LIN to OUT2 L C Connect Ground GND to Ground GND D MIC RET and OUT RET are for HD audio panel only You don t need to connect them for AC 97 audio panel E To activate the front mic For Windows XP XP 64 bit OS Select Mixer Select Recorder Then click FrontMic For Windows 7 7 64 bit Vista Vista 64 bit OS Go to the FrontMic Tab in the Realtek Control panel Adjust Recording Volume System Panel Header igi This header accommodates 9 pin PANEL 1 GND several system front panel see p 12 No 20 functions za pe i GHO HOLED HDLEC 53 Connect the power switch reset switch and system status indicator on the chassis to
29. an speed and the critical voltage ASROCK UEFI SETUP UTILITY TOMORROW S TECHNOLOGY TODAY CPU Fan 1 amp 2 Setting This allows you to set the CPU fan 1 amp 2 speed Con guration options Full On and Automatic Mode The default is value Full On Chassis Fan 1 Setting This allows you to set the chassis fan 1 speed Con guration options Full On Manual Mode and Automatic Mode The default is value Full On Chassis Fan 2 Setting This allows you to set the chassis fan 2 speed Con guration options Full On and Manual Mode The default is value Full On Chassis Fan 3 Setting This allows you to set the chassis fan 3 speed Con guration options Full On and Manual Mode The default is value Full On 62 3 6 Boot Screen In this section it will display the available devices on your system for you to con g ure the boot settings and the boot priority ASROCK UEFI SETUP UTILITY TOMORROW S TECHNOLOGY TODAY Setup Prompt Timeout This shows the number of seconds to wait for setup activation key 65535 0xFFFF means inde nite waiting Bootup Num Lock If this item is set to On it will automatically activate the Numeric Lock function after boot up Full Screen Logo Use this item to enable or disable OEM Logo The default value is Enabled AddOn ROM Display Use this option to adjust AddOn ROM Display If you enable the option Full Screen Logo but you want to see the AddOn ROM information when the s
30. at audio ex perience from the portable audio devices such like MP3 player or mobile phone to your PC even when the PC is turned off or in ACPI S5 mode This motherboard also provides a free 3 5mm audio cable optional that ensures users the most convenient computing environment While CPU overheat is detected the system will automatically shutdown Before you resume the system please check if the CPU fan on the moth erboard functions properly and unplug the power cord then plug it back again To improve heat dissipation remember to spray thermal grease between the CPU and the heatsink when you install the PC system 10 15 EuP stands for Energy Using Product was a provision regulated by Eu ropean Union to de ne the power consumption for the completed system According to EuP the total AC power of the completed system shall be under 1 00W in off mode condition To meet EuP standard an EuP ready motherboard and an EuP ready power supply are required According to Intel s suggestion the EuP ready power supply must meet the standard of 5v standby power ef ciency is higher than 50 under 100 mA current consumption For EuP ready power supply selection we recommend you checking with the power supply manufacturer for more details Besides please be noted that if you enable ASRock On Off Play Technology your system will not meet EuP standard To meet EuP standard please dis able ASRock On Off Play Technology rst 11 1 3 Motherboa
31. ation 66 Installing OS on a HDD Larger Than 2TB This motherboard is adopting UEFI BIOS that allows Windows OS to be installed on a large size HDD gt 2TB Please follow below procedure to install the operating system 1 Please make sure to use Windows Vista 64 bit with SP1 or above or Windows 7 64 bit 2 Press F2 or Delete at system POST Set AHCI Mode in UEFI Setup Utility gt Advanced Storage Con guration SATA Mode 3 Choose the item UEFI xxx to boot in UEFI Setup Utility gt Boot gt Boot Option 1 xxx is the device which contains your Windows installation les Normally it is an optical drive You can also press lt F11 gt to launch boot menu at system POST and choose the item UEFI xxx to boot 4 Start Windows installation 67
32. chten ERRRR ee nent 54 3 4 2 North Bridge Con GUrATON s nee 55 3 4 3 South Bridge Con guration eeessssssssse 56 3 4 4 Storage Corn QurallODcssescssesnvnte sien sx that enne nee 57 3 4 5 Super IO Con Jurallori cerit t ibn tri te Sinne 58 940 ACPI Con QU i FERE IIR eme 59 3 4 7 USB Con Ur ter 61 3 5 Hardware Health Event Monitoring Screen 62 3 6 Boot Screen sieut pan xor oe diib ne bi dta g eme enee trim usaba otte one 63 Sd FEN ENN 64 OA SEN Ne 65 4 Software Support ss 66 4 1 Install Operating System 66 4 2 Support CD Information uanmaearsimrjennemednnaemesnuinivneivn 66 42 1 Running Support CD cett neismoniirstesnnse 66 422 Drivers MN 66 4 2 3 Utilities MONS E 66 4 24 Lomacnbmaibnusu orakler bes ee 66 1 Introduction Thank you for purchasing ASRock A75 Pro4 motherboard a reliable motherboard produced under ASRock s consistently stringent quality control It delivers excellent performance with robust design conforming to ASRock s commitment to quality and endurance In this manual chapter 1 and 2 contain introduction of the motherboard and step by step guide to the hardware installation Chapter 3 and 4 contain the con guration guide to BIOS setup and information of the Support CD Because the motherboard speci cations and the BIOS software might be updated the content of this manual will be subject to change without notice In case any modi cat
33. d you purchase not bundled with this motherboard Please refer to your graphics card vendor for details Connect the DVI monitor cable to the DVI connector on the Radeon graph ics card on PCIE2 slot You may use the DVI to D Sub adapter to convert the DVI connector to D Sub interface and then connect the D Sub monitor cable to the DVI to D Sub adapter 21 2 5 2 Driver Installation and Setup Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Power on your computer and boot into OS Remove the AMD driver if you have any VGA driver installed in your sys tem The Catalyst Uninstaller is an optional download We recommend using this utility to uninstall any previously installed Catalyst drivers prior to installation Please check AMD website for AMD driver updates Install the required drivers to your system For Windows XP OS A AMD recommends Windows XP Service Pack 2 or higher to be installed If you have Windows XP Service Pack 2 or higher installed in your system there is no need to download it again http www microsoft com windowsxp sp2 default mspx B You must have Microsoft NET Framework installed prior to downloading and installing the CATALYST Control Center Please check Microsoft website for details For Windows 7 Vista OS Install the CATALYST Control Center Please check AMD website for de tails Restart your computer Install the VGA card drivers to your system and restart
34. ding has failed 0x52 Memory initialization error Invalid memory size or memory modules do not o4 CPU mismatch 0x58 CPU self test failed or possible CPU cache error 0x59 CPU micro code is not found or micro code update is failed SA 0x5C 0x5F Reserved for future AMI error codes S3 Resume is stared S3 Resume PPI is called by the DXE IPL S3 Boot Script execution Video repost OE ONE S3 Resume PPI not Found OxEA S3 Resume Boot Script Error S3 OS Wake Error 3 OS Wake Error Cid Recovery condition triggered by rmware Auto recovery 0X61 NVRAM initialization 38 x62 Installation of the South Bridge Runtime Services 0x63 CPU DXE initialization is started x64 CPU DXE initialization CPU module speci c 0x65 CPU DXE initialization CPU module speci c x66 CPU DXE initialization CPU module speci c x67 68 x69 North Bridge DXE initialization North Bridge module speci c x6 xir 70 South Bridge DXE Initialization South Bridge module speci c South Bridge DXE Initialization South Bridge module speci c x76 South Bridge DXE Initialization South Bridge module speci c x78 ACPI module initialization x80 Ox8F OEM DXE initialization codes Boot Device Selection BDS phase is started Driver connecting is started PCI Bus initialization is started PCI Bus Request Resources POBus Request Resors S 39 E 0 Error loading Boot Option Loadlmage returned error Boot Option is failed Star
35. e auto matically enabled when you install AMD RADEON HD6670 6570 6450 graphics card The default value is Auto DVI Function Use this to select DVI function when you install the DVI to HDMI adapter to DVI port Con guration options as Dual Link DVI and as HDMI If you select as Dual Link DVI you can use Dual Link DVI monitor without au dio function If you select as HDMI you can use HDMI monitor with audio function The default value is as Dual Link DVI 55 3 4 3 South Bridge Configuration ASROCK UEFI SETUP UTILITY TOMORROW S TECHNOLOGY TODAY Onboard HD Audio Select Auto Enabled or Disabled for the onboard HD Audio feature If you select Auto the onboard HD Audio will be disabled when PCI Sound Card is plugged Front Panel Select Auto or Disabled for the onboard HD Audio Front Panel On Off Play Use this item to enable or disable On Off Play Technology The defaultval ue is Enabled When On Off Play is enabled Deep Sx will be disabled If you want to enable Deep Sx please disable On Off Play rst Onboard LAN This allows you to enable or disable the onboard LAN feature Onboard IEEE 1394 This allows you to enable or disable the onboard IEEE 1394 feature Good Night LED Enable this option to turn off Power LED and Port80 LED when the system is power on The keyboard LED will also be turned off in S1 S3 and S4 state The default value is Auto Onboard Debug Port LED Use this to enable or dis
36. em devices 65 4 Software Support 4 1 Install Operating System This motherboard supports various Microsoft Windows operating systems 7 7 64 bit Vista Vista 64 bit XP SP3 XP 64 bit Because motherboard settings and hardware options vary use the setup procedures in this chapter for general reference only Refer to your OS documentation for more information 4 2 Support CD Information The Support CD that came with the motherboard contains necessary drivers and useful utilities that enhance the motherboard features 4 2 1 Running The Support CD To begin using the support CD insert the CD into your CD ROM drive The CD automatically displays the Main Menu if AUTORUN is enabled in your com puter If the Main Menu did not appear automatically locate and double click on the le ASSETUP EXE from the BIN folder in the Support CD to display the menus 4 2 2 Drivers Menu The Drivers Menu shows the available devices drivers if the system detects the installed devices Please install the necessary drivers to activate the devices 4 2 3 Utilities Menu The Utilities Menu shows the applications software that the motherboard sup ports Click on a speci c item then follow the installation wizard to install it 4 2 4 Contact Information If you need to contact ASRock or want to know more about ASRock welcome to visit ASRock s website at http www asrock com or you may contact your dealer for further inform
37. emove any component ensure that the power is switched off or the power cord is detached from the power supply Failure to do so may cause severe damage to the motherboard peripherals and or components 1 Unplug the power cord from the wall socket before touching any component 2 To avoid damaging the motherboard components due to static elec tricity NEVER place your motherboard directly on the carpet or the like Also remember to use a grounded wrist strap or touch a safety grounded object before you handle components 3 Hold components by the edges and do not touch the ICs 4 Whenever you uninstall any component place it on a grounded anti static pad or in the bag that comes with the component 5 When placing screws into the screw holes to secure the mother board to the chassis please do not over tighten the screws Doing so may damage the motherboard 15 2 1 CPU Installation Step 1 Unlock the socket by lifting the lever upto a 90 angle Step 2 Position the CPU directly above the socket such that the CPU corner with the golden triangle matches the socket corner with a small triangle Step 3 Carefully insert the CPU into the socket until it ts in place The CPU ts only in one correct orientation DO NOT force the CPU into the socket to avoid bending of the pins Step 4 When the CPU is in place press it rmly on the socket while you push down the socket lever to secure the CPU The lever clicks on t
38. h some memory modules or power supplies Please set this item to Disable if above issue occurs SVM When this option is set to Enabled a VMM Virtual Machine Architecture can utilize the additional hardware capabilities provided by AMD V The default value is Enabled Con guration options Enabled and Disabled CPU Thermal Throttle Use this item to enable CPU internal thermal control mechanism to keep the CPU from overheated The default value is Auto 54 3 4 2 North Bridge Configuration ASROCK UEFI SETUP UTILITY a mate be eee hed ol TOMORROW S TECHNOLOGY TODAY Primary Graphics Adapter This item will switch the PCI Bus scanning order while searching for video card It allows you to select the type of Primary VGA in case of multiple video controllers The default value of this feature is PCI Express Con guration options Onboard PCI and PCI Express Share Memory This allows you to set the share memory feature The default value is Auto Configuration options Auto 32MB 64MB 128MB 256MB and 512MB Onboard HDMI HD Audio This allows you to enable or disable the Onboard HDMI HD Audio fea ture Dual Graphics This item appears only when you install AMD RADEON HD6670 6570 6450 graphics card on this motherboard Use this to enable or disable Dual Graphics feature If you enable this option the primary monitor will be onboard VGA If you select Auto Dual Graphics function will b
39. he side tab to indicate that it is locked LeVer 902 UP 1 d Socket Corner Small Triangle STEP 2 STEP 3 STEP 4 Lift Up The Socket Lever Match The CPU Golden Triangle Push Down And Lock To The Socket Corner Small The Socket Lever Triangle 2 2 Installation of CPU Fan and Heatsink After you install the CPU into this motherboard it is necessary to install a larger heatsink and cooling fan to dissipate heat You also need to spray thermal grease between the CPU and the heatsink to improve heat dis sipation Make sure that the CPU and the heatsink are securely fastened and in good contact with each other Then connect the CPU fan to the CPU FAN connector CPU FAN see Page 12 No 5 or CPU FAN2 see Page 12 No 6 For proper installation please kindly refer to the instruction manuals of the CPU fan and the heatsink 2 3 Installation of Memory Modules DIMM This motherboard provides four 240 pin DDR3 Double Data Rate 3 DIMM slots and supports Dual Channel Memory Technology For dual channel con guration you always need to install identical the same brand speed size and chip type DDR3 DIMM pair in the slots of the same color In other words you have to install identical DDR3 DIMM pair in Dual Channel A DDR3_ A1 and DDR3 B1 Blue slots see p 12 No 7 or identical DDR3 DIMM pair in Dual Channel B DDR3 A2 and DDR3 B2 White slots see p 12 No 8 so that Dual Channel Memory Technology can be activated This motherboard
40. ility of such damages arising from any defect or error in the manual or product FC This device complies with Part 15 of the FCC Rules Operation is subject to the fol lowing two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation CALIFORNIA USA ONLY The Lithium battery adopted on this motherboard contains Perchlorate a toxic substance controlled in Perchlorate Best Management Practices BMP regulations passed by the California Legislature When you discard the Lithium battery in Cali fornia USA please follow the related regulations in advance Perchlorate Material special handling may apply see www dtsc ca gov hazardouswaste perchlorate ASRock Website http www asrock com l OCTO a 5 Vel Package CODIGOS nn MORE NE ERE REO neu EE en 5 1 2 Speci AO Rm 6 13 IWOMMEIDOAIG Layout auras 12 e e S 13 TONO r UE 15 Pre installation Precautions cccccssecccsseecceecccneeecseeeseusecsesesaues 15 PI ANN 16 2 2 Installation of CPU Fan and Heatsink 16 2 3 Installation of Memory Modules DIMM 17 2 4 Expansion Slots PCI and PCI Express Slots 19 2 5 CrossFirex and Quad CrossFirex Operation Guide 20 2 6 Dual Graphics Operation Guide rrarnrrrrannnorrrnnnnorrannnvnnrnnnnennn 24 2 7
41. ions of this manual occur the updated ver sion will be available on ASRock website without further notice You may nd the latest VGA cards and CPU support lists on ASRock website as well ASRock website http www asrock com If you require technical support related to this motherboard please visit our website for speci c information about the model you are using www asrock com support index asp 1 1 Package Contents ASRock A75 Pro4 Motherboard ATX Form Factor 12 0 in x 8 8 in 30 5 cm x 22 4 cm ASRock A75 Pro4 Quick Installation Guide ASRock A75 Pro4 Support CD 4 x Serial ATA SATA Data Cables Optional 1 x 3 5mm Audio Cable Optional 1 x I O Panel Shield ASRock Reminds You To get better performance in Windows 7 7 64 bit Vista Vista 64 bit it is recommended to set the BIOS option in Storage Con guration to AHCI mode For the BIOS setup please refer to the User Manual in our support CD for details 1 2 Specifications Platform ATX Form Factor 12 0 in x 8 8 in 30 5 cm x 22 4 cm All Solid Capacitor design Support for Socket FM1 100W processors V4 1 Power Phase Design Supports AMD s Cool n Quiet Technology UMI Link GEN2 Dual Channel DDR3 Memory Technology see CAUTION 1 4 x DDR3 DIMM slots Support DDR3 2400 OC 1866 1600 1333 1066 800 non ECC un buffered memory see CAUTION 2 Max capacity of system memory 32GB see CAUTION 3 Expansion Slot
42. l work if you adopt a traditional 20 pin ATX power supply To use the 20 pin ATX power supply please plug your power supply along with Pin 1 and Pin 13 20 Pin ATX Power Supply Installation ATX 12V Power Connector POE Please connect an ATX 12V 8 pin ATX12V1 power supply to this connector see p 12 No 2 1 Though this motherboard provides 8 pin ATX 12V power connector it can still work ba if you adopt a traditional 4 pin ATX 12V power supply To use the 4 zs 4 pin ATX power supply please plug your power supply along with cr Pin 1 and Pin 5 4 Pin ATX 12V Power Supply Installation s IEEE 1394 Header RXTPAM 0 Besides one default IEEE 1394 9 pin FRONT 1394 T RXrPBM 0 port on the I O panel there is see p 12 No 32 one IEEE 1394 header FRONT 1394 on this motherboard This IEEE 1394 header can support one IEEE 1394 port RXTPAP O 34 Serial port Header 9 pin COM1 see p 12 No 30 HDMI SPDIF Header 2 pin HDMI SPDIF1 see p 12 No 31 GND SPDIFOUT 35 This COM1 header supports a serial port module HDMI SPDIF header providing SPDIF audio output to HDMI VGA card allows the system to connect HDMI Digital TV projector LCD devices Please connect the HDMI SPDIF connector of HDMI VGA card to this header 2 11 Smart Switches This motherboard has three smart switches power switch reset switch and clear CMOS switch allowing users to quickly turn on off or reset the system
43. lt as RAID 1 then it is called Hot Swap for the ac tion to insert and remove the SATA3 HDDs while the system is still power on and in working condition 41 2 15 SATAS HDD Hot Plug Feature and Operation Guide This motherboard supports Hot Plug feature for SATA3 HDD in RAID AHCI mode Please read below operation guide of Hot Plug feature carefully Before you process the SATA3 HDD Hot Plug please check below cable accessories from the motherboard gift box pack A 7 pin SATA data cable B SATA power cable with SATA 15 pin power connector interface A SATA data cable Red B SATA power cable The SATA 15 pin power 1x4 pin conventional connector connector Black connect power connector White to SATA3 HDD connect to power supply Caution 1 Without SATA 15 pin power connector interface the SATA3 Hot Plug cannot be processed 2 Even some SATA3 HDDs provide both SATA 15 pin power connector and IDE 1x4 pin conventional power connector interfaces the IDE 1x4 pin conventional power connector interface is de nitely not able to support Hot Plug and will cause the HDD damage and data loss Points of attention before you process the Hot Plug 1 Below operation procedure is designed only for our motherboard which supports SATA3 HDD Hot Plug The SATA3 Hot Plug feature might not be supported by the chipset because of its limitation the SATA3 Hot Plug support information of our motherboard is indicated in the product spec on o
44. oard supports surround display upgrade With the internal VGA output support DVI D D Sub and HDMI and external add on PCI Express VGA cards you can easily enjoy the bene ts of surround display feature Please refer to the following steps to set up a surround display environment 1 Install the PCI Express VGA cards on PCIE2 and PCIE4 slots Please refer to page 19 for proper expansion card installation procedures for details 2 Connect DVI D monitor cable to DVI D port on the I O panel connect D Sub monitor cable to D Sub port on the I O panel or connect HDMI monitor cable to HDMI port on the I O panel Then connect other monitor cables to the corresponding connectors of the add on PCI Express VGA cards on PCIE2 and PCIE4 slots 3 Boot your system Press lt F2 gt or lt Del gt to enter UEFI setup Enter Share Memory option to adjust the memory capability to 32MB 64MB 128MB 256MB or 512MB to enable the function of D sub Please make sure that the value you select is less than the total capability of the system memory If you do not adjust the UEFI setup the default value of Share Memory Auto will disable D Sub function when the add on VGA card is inserted to this motherboard 4 Install the onboard VGA driver and the add on PCI Express VGA card driver to your system If you have installed the drivers already there is no need to install them again 5 Set up a multi monitor display For Windows XP XP
45. ocessor and a discrete graphics processor to operate simultaneously with combined output to a single display for blisteringly fast frame rates Currently AMD Dual Graphics Technology is only supported with Windows 7 OS and is not available with Windows Vista XP OS What does an AMD Dual Graphics system include An AMD Dual Graphics system includes an AMD Radeon HD 65XX 64XX graphics processor and a motherboard based on an AMD A75 FCH Hudson D3 integrated chipset all operating in a Windows 7 environment Please refer to below PCI Express graphics card support list for AMD Dual Graphics For the future update of more compatible PCI Express graphics cards please visit AMD website for further information Chipset Model i river AMD RADEON HD6670 ASUS DIS PCIE2 1 ASUS HDMI EAH6670 DI 1GD3 1G DDR3 8 86 8 86 8 86 AMD RADEON HD6570 MSI DIS PCIE2 1 MSI HDMI R6570 MD1GD3 LP 1G DDR3 AMD RADEON HD6450 MSI DIS PCIE2 1 MSI HDMI R6450 MD1GD3 LP 1G DDR3 Enjoy the benefit of AMD Dual Graphics Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Please keep the default UEFI setting of Dual Graphics option on Auto Install one AMD RADEON HD6670 6570 6450 PCI Express graphics card to PCIE2 slot blue Connect the monitor cable to the onboard VGA port Please be noted that the current VGA driver VBIOS can allow Dual Graphics output from on board display only For any future update please refer to ou
46. onnectors Placing jumper caps over the headers and connectors will cause permanent damage of the motherboard Serial ATA3 Connectors SATA3 1 see p 12 No 15 SATA3 2 see p 12 No 16 SATA3 3 see p 12 No 14 SATA3 4 see p 12 No 13 SATA3 5 see p 12 No 12 Serial ATA SATA Data Cable Optional 3 5mm Audio Cable Optional USB 2 0 Headers 9 pin USB6 7 see p 12 No 28 9 pin USB8 9 see p 12 No 27 9 pin USB10 11 see p 12 No 25 SATA3 5 These ve Serial ATA3 Imm SATA3 connectors support lt FY FY SATA data cables for internal Al 2 storage devices The current 5 LE 5 SATA3 interface allows up to if i 6 0 Gb s data transfer rate lt lt Either end of the SATA data cable can be connected to the SATA3 hard disk or the SATA3 connector on this motherboard i Either end of the 3 5mm audio cable can be connected to the portable audio devices such as MP3 player and mobile phone or the Line in port of your PC mE Besides two default USB 2 0 Ten ports on the I O panel there B are three USB 2 0 headers on this motherboard Each USB 2 0 header can support two USB 2 0 ports P 8 USB PWR USB PWR P 1 P411 GND DUMMY GND P 10 P 10 USB_PWR 31 Infrared Module Header This header supports an 5 pin IR1 E optional wireless transmitting see p 12 No 23 i and receiving infrared module GND IRRX Consumer Infrared Module He
47. or clear the CMOS values Power Switch Power Switch is a smart switch PWRBTN see p 12 No 18 allowing users to quickly turn on off the system e Reset Switch Reset Switch is a smart switch RSTBTN RESET allowing users to quickly reset see p 12 No 19 the system Clear CMOS Switch Clear CMOS Switch is a smart CLRCBTN aa switch allowing users to quickly see p 13 No 14 clear the CMOS values 36 2 12 Dr Debug Dr Debug is used to provide code information which makes troubleshooting even easier Please see the diagrams below for reading the Dr Debug codes Power on Reset type detection soft hard Ox0A OEM initialization after microcode loading Microcode not loaded PEI Core is started A Ox1A Pre memory South Bridge initialization South Bridge module speci c Ox1B Pre memory South Bridge initialization South Bridge module speci c XID UXZA OEM pre memory initialization codes MA a e o 0x2F Memory initialization other CPU post memory initialization Application Processor s AP initialization CPU post memory initialization Boot Strap Processor BSP selection 0x36 CPU post memory initialization System Management Mode SMM initialization 37 0x37 0x38 0x38 GA EE mec 0x30 OE Ox3F Ox4E OEM post memory initialization codes DXE IPL is started Memory initialization error Invalid memory type or incompatible memory speed 0x51 Memory initialization error SPD rea
48. performance and image quality in any 3D application Currently CrossFireX feature is supported with Windows XP with Service Pack 2 Vista 7 OS Quad CrossFireX feature are supported with Windows Vista 7 OS only Please check AMD website for AMD CrossFireX driver updates 4 1 If a customer incorrectly configures their system they will not see the 3 performance bene ts of CrossFirex All three CrossFireX components a CrossFireX Ready graphics card a CrossFireX Ready motherboard and a CrossFireX Edition co processor graphics card must be installed correctly to bene t from the CrossFireX multi GPU platform 2 If you pair a 12 pipe CrossFireX Edition card with a 16 pipe card both cards will operate as 12 pipe cards while in CrossFireX mode 2 5 Graphics Card Setup w AN Different CrossFireX cards may require different methods to enable CrossFi reX feature For other CrossFireX cards that AMD has released or will release in the future please refer to AMD graphics card manuals for detailed installation guide Step 1 Insert one Radeon graphics card into PCIE2 slot and the other Radeon graphics card to PCIEA slot Make sure that the cards are properly seated on the slots 20 Step 2 Step 3 Connect two Radeon graphics cards by installing CrossFire Bridge on CrossFire Bridge Interconnects on the top of Radeon graphics cards CrossFire Bridge is provided with the graphics car
49. phics card on PCIE2 slot 2 In CrossFireX mode please install PCI Express x16 graphics cards on PCIE2 and PCIE4 slots 3 Please connect a chassis fan to motherboard chassis fan connec tor CHA FAN1 CHA FAN2 or CHA FAN3 when using multiple graphics cards for better thermal environment Installing an expansion card Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Before installing the expansion card please make sure that the power supply is switched off or the power cord is unplugged Please read the documentation of the expansion card and make necessary hardware settings for the card before you start the installation Remove the system unit cover if your motherboard is already installed in a chassis Remove the bracket facing the slot that you intend to use Keep the screws for later use Align the card connector with the slot and press rmly until the card is completely seated on the slot Fasten the card to the chassis with screws Replace the system cover 19 2 5 CrossFirex and Quad CrossFirex Operation Guide This motherboard supports CrossFireX and Quad CrossFireX feature CrossFireX technology offers the most advantageous means available of combining multiple high performance Graphics Processing Units GPU in a single PC Combining a range of different operating modes with intelligent software design and an innovative interconnect mechanism CrossFirex enables the highest possible level of
50. r website for further information Boot into OS Please remove the AMD driver if you have any VGA driver installed in your system Install the onboard VGA driver from our support CD to your system for both the onboard VGA and the discrete graphics card Restart your computer Right click the desktop Click AMD VISION Engine Control Center to enter AMD VISION Engine Control Center AMD VISION Engine Control Center View b Sort by Refresh Paste Paste shortcut New gt Screen resolution gt Gadgets EX Personalize 24 Step 7 You can also click AMD VISION Engine Control Center on your Windows taskbar to enter AMD VISION Engine Control Center Customize 3 55 AM AMD VISION Engine Control Center Step 8 In AMD VISION Engine Control Center please choose Performance Click AMD CrossFire vio AMD WOO regire Control Carrier We AMD VISION begir Corral Center Step 10 Reboot your system Then you can freely enjoy the bene t of Dual Graphics feature Dual Graphics appearing here is a registered trademark of AMD Technologies Inc and is used only for identi cation or explanation and to the owners bene t without intent to infringe For further information of AMD Dual Graphics technology please check AMD website for up dates and details 25 2 7 Dual Monitor and Surround Display Features Dual Monitor Feature This motherboard supports dual monitor feature
51. rd Layout NO oO BB WD 10 11 12 13 14 15 16 17 18 19 20 21 1 2 3 4 5 6 7 8 22 4cm 8 8 in X a m i o O 3 e s2 SEE E lle al ME MSRock i 5 xl A75 Pro4 3 40 Dual Graphics 39 PCIE2 i Ez DX11 38 pcies AMD 37 USB 3 0 El rus d un Pen rer ias ErP EuPReady XFastUsB 7 Nm 13 m am me 5 35 PCI2 sil LE 1394a RoHS E 16 A PCI3 ee Seto 33 32 31 30 2928 27 26 25 2423 22 21 20 Power Fan Connector PWR FAN1 22 Chassis Fan Connector CHA FAN1 ATX 12V Power Connector ATX12V1 23 Infrared Module Header IR1 CPU Heatsink Retention Module 24 Power LED Header PLED1 CPU Socket 25 USB 2 0 Header USB10 11 Blue CPU Fan Connector CPU FAN1 26 SPI Flash Memory 32Mb CPU Fan Connector CPU FAN2 27 USB 2 0 Header USB8 9 Blue 2 x 240 pin DDR3 DIMM Slots 28 USB 2 0 Header USB6 7 Blue Dual Channel A DDR3 A1 DDR3_B1 Blue 29 Consumer Infrared Module Header CIR1 2 x 240 pin DDR3 DIMM Slots 30 COM Port Header COM1 Dual Channel B DDR3 A2 DDR3 B2 White 31 HDMI SPDIF Header HDMI SPDIF1 White ATX Power Connector ATXPWR1
52. s Y D Then you will see these messages Please insert a diskette into the floppy drive WARNING Formatting the floppy diskette will lose ALL data in it Start to format and copy files YN Please inserta oppy diskette into the oppy drive and press any key E The system will start to format the oppy diskette and copy SATA3 drivers into the oppy diskette 44 STEP 3 Use RAID Installation Guide to set RAID configuration Before you start to con gure RAID function you need to check the RAID installation guide in the Support CD for proper con guration Please refer to the BIOS RAID installation guide part of the document in the following path in the Support CD RAID Installation Guide STEP 4 Install Windows XP XP 64 bit OS on your system After step 1 2 3 you can start to install Windows XP XP 64 bit OS on your system At the beginning of Windows setup press F6 to install a third party RAID driver When prompted insert the SATA3 driver diskette containing the AMD RAID driver After reading the oppy disk the driver will be presented Select the driver to install according to the OS you install 2 17 2 Installing Windows 7 7 64 bit Vista Vista 64 bit With RAID Functions If you want to install Windows 7 7 64 bit Vista Vista 64 bit on a RAID disk composed of 2 or more SATA3 HDDs with RAID functions please follow below steps STEP 1 Set up UEFI A Enter UEFI SETUP UTIL
53. t the HDTV or LCD monitor you purchase is compatible 28 2 8 ASRock Smart Remote Installation Guide ASRock Smart Remote is only used for ASRock motherboard with CIR header Please refer to below procedures for the quick installation and usage of ASRock Smart Remote Step1 Find the CIR header located next to the USB 2 0 header on ASRock motherboard USB 2 0 header 9 pin blue CIR header 4 pin white Step2 Connect the front USB cable to the di USB 2 0 header as below pin 1 5 and the CIR header Please make sure the wire assignments and the 1 pin assignments are matched correctly Step3 Install Multi Angle CIR Receiver to the front USB port If Multi Angle CIR Receiver cannot successfully receive the infrared signals from MCE Remote Controller please try to install it to the other front USB port 3 CIR sensors in different angles 1 Only one of the front USB port can support CIR function When the CIR function is enabled the other port will remain USB function 2 Multi Angle CIR Receiver is used for front USB only Please do not use the rear USB bracket to connect it on the rear panel Multi Angle CIR Receiver can receive the multi direction infrared signals top down and front which is compatible with most of the chassis on the market 3 The Multi Angle CIR Receiver does not support Hot Plug function Please install it before you boot the system ASRock Smart Remote is only supported by
54. the menu bar and then press Enter to get into the sub screen 48 3 1 2 Navigation Keys Please check the following table for the function description of each navigation key Navigation Key s Function Description Moves cursor left or right to select Screens p U Moves cursor up or down to select items To change option for the selected items lt Enter gt To bring up the selected screen lt F1 gt To display the General Help Screen lt F9 gt To load optimal default values for all the settings lt F10 gt To save changes and exit the UEFI SETUP UTILITY lt ESC gt To jump to the Exit Screen or exit the current screen 3 2 Main Screen When you enter the UEFI SETUP UTILITY the Main screen will appear and display the system overview ASROCK UEFI SETUP UTILITY TOMORROW S TECHHOLOOY TODAY System Time Hour Minute Second Use this item to specify the system time System Date Day Month Date Year Use this item to specify the system date 49 3 3 OC Tweaker Screen In the OC Tweaker screen you can set up overclocking features ASROCK UEFI SETUP UTILITY TOMORROW S TECHNOLOGY TODAY CPU Configuration Overclock Mode Use this to select Overclock Mode Configuration options Auto and Manual The default value is Auto APU PCIE Frequency MHz This item appears only when you set the item Overclock Mode to Manual The default value is 100 Please be noted that overclocking may reduce
55. tion No Link On ACT LINK SPEED SPEED LED LED LED Status 10Mbps connection Blinking Data Activity 100Mbps connection 1Gbps connection LAN Port If you use 2 channel speaker please connect the speaker s plug into Front Speaker Jack See the table below for connection details in accordance with the type of speaker you use TABLE for Audio Output Connection Audio Output Channels Front Speaker Rear Speaker Central Bass Line In or Side Speaker 13 To enable Multi Streaming function you need to connect a front panel audio cable to the front panel audio header After restarting your computer you will nd Mixer tool on your system Please select Mixer ToolBox L3 click Enable playback multi streaming and click ok Choose 2CH 4CH 6CH or 8CH and then you are allowed to select Realtek HDA Pri mary output to use Rear Speaker Central Bass and Front Speaker or select Realtek HDA Audio 2nd output to use front panel audio eSATA3 connector supports SATA Gen3 in cable 1M 14 2 Installation This is an ATX form factor 12 0 in x 8 8 in 30 5 cm x 22 4 cm motherboard Before you install the motherboard study the con guration of your chassis to ensure that the motherboard ts into it Pre installation Precautions Take note of the following precautions before you install motherboard components or change any motherboard settings 4 Before you install or r
56. tlmage returned error Flash update is failed Reset protocol is not available 40 2 13 Serial ATA3 SATA3 Hard Disks Installation This motherboard adopts AMD A75 FCH Hudson D3 chipset that supports Serial ATA3 SATA3 hard disks and RAID RAID 0 RAID 1 and RAID 10 functions You may install SATA3 hard disks on this motherboard for internal storage devices This section will guide you to install the SATA3 hard disks STEP 1 Install the SATA3 hard disks into the drive bays of your chassis STEP 2 Connect the SATA power cable to the SATA3 hard disk STEP 3 Connect one end of the SATA data cable to the motherboard s SATA3 con nector STEP 4 Connect the other end of the SATA data cable to the SATA3 hard disk 2 14 Hot Plug and Hot Swap Functions for SATA3 HDDs This motherboard supports Hot Plug and Hot Swap functions for SATA3 in RAID AHCI mode AMD A75 FCH Hudson D3 chipset provides hardware support for Advanced Host controller Interface AHCI a new programming interface for SATA host controllers developed thru a joint industry effort 4 1 NOTE 7 What is Hot Plug Function If the SATA3 HDDs are NOT set for RAID con guration it is called Hot Plug for the action to insert and remove the SATA3 HDDs while the system is still power on and in working condition However please note that it cannot perform Hot Plug if the OS has been installed into the SATA3 HDD What is Hot Swap Function If SATA3 HDDs are bui
57. ur website www asrock com 2 Make sure your SATA3 HDD can support Hot Plug function from your dealer or HDD user manual The SATA3 HDD which cannot support Hot Plug function will be damaged under the Hot Plug operation 3 Please make sure the SATA3 driver is installed into system properly The latest SATA3 driver is available on our support website www asrock com 4 Make sure to use the SATA power cable amp data cable which are from our motherboard package 5 Please follow below instructions step by step to reduce the risk of HDD crash or data loss 42 How to Hot Plug a SATA3 HDD Points of attention before you process the Hot Plug Please do follow below instruction sequence to process the Hot Plug improper procedure will cause the SATA3 HDD damage and data loss SRE Please connect SATA power cable 1x4 pin O4 Connect SATA data cable to end White to the power supply 1x4 pin the motherboard s SATAII SATA3 cable connector SATA power cable 1x4 pin Ipower connector White Sie Connect SATA 15 pin power cable jeg Connect SATA data cable to the connector Black end to SATA3 HDD SATA3 HDD 27 o IR i i i uns How to Hot Unplug a SATA3 HDD Points of attention before you process the Hot Unplug Please do follow below instruction sequence to process the Hot Unplug improper procedure will cause the SATA3 HDD damage and data loss Unplug SATA data cable from SATA3 HDD side 43 2
58. ware Monitor Fan Control Overclocking OC DNA and IES In Hard ware Monitor it shows the major readings of your system In Fan Control it shows the fan speed and temperature for you to adjust In Overclock ing you are allowed to overclock CPU frequency for optimal system performance In OC DNA you can save your OC settings as a pro le and share with your friends Your friends then can load the OC pro le to their own system to get the same OC settings In IES Intelligent Energy Saver the voltage regulator can reduce the number of output phases to improve ef ciency when the CPU cores are idle without sacri cing com puting performance Please visit our website for the operation procedures of ASRock Extreme Tuning Utility AXTU ASRock website http www asrock com 10 dde 123 T3 14 ASRock Instant Flash is a BIOS ash utility embedded in Flash ROM This convenient BIOS update tool allows you to update system BIOS without entering operating systems rst like MS DOS or Windows With this utility you can press lt F6 gt key during the POST or press lt F2 gt key to BIOS setup menu to access ASRock Instant Flash Just launch this tool and save the new BIOS le to your USB ash drive oppy disk or hard drive then you can update your BIOS only in a few clicks without prepar ing an additional oppy diskette or other complicated ash utility Please be noted that the USB ash drive or hard drive must use FAT32 16 12 le system If
59. you desire a faster less restricted way of charging your Apple devices such as iPhone iPod iPad Touch ASRock has prepared a wonderful solu tion for you ASRock APP Charger Simply installing the APP Charger driver it makes your iPhone charged much quickly from your computer and up to 40 faster than before ASRock APP Charger allows you to quickly charge many Apple devices simultaneously and even supports continuous charging when your PC enters into Standby mode S1 Sus pend to RAM S3 hibernation mode S4 or power off S5 With APP Charger driver installed you can easily enjoy the marvelous charging experience than ever ASRock website http www asrock com Feature AppCharger index asp SmartView a new function of internet browser is the smart start page for IE that combines your most visited web sites your history your Facebook friends and your real time newsfeed into an enhanced view for a more personal Internet experience ASRock motherboards are exclusively equipped with the SmartView utility that helps you keep in touch with friends on the go To use SmartView feature please make sure your OS version is Windows 7 7 64 bit Vista Vista 64 bit and your browser version is IE8 ASRock website http www asrock com Feature SmartView index asp ASRock XFast USB can boost USB storage device performance The performance may depend on the property of the device ASRock On Off Play Technology allows users to enjoy the gre
60. ystem boots please select Enabled Con guration options Enabled and Disabled The default value is Enabled Boot Failure Guard Enable or disable the feature of Boot Failure Guard Boot Failure Guard Count Enable or disable the feature of Boot Failure Guard Count Boot From Onboard LAN Use this item to enable or disable the Boot From Onboard LAN feature 63 3 7 Security Screen In this section you may set or change the supervisor user password for the system For the user password you may also clear it ASROCK UEFI SETUP UTILITY TOMORROW S TECHNOLOGY TODAY 64 3 8 Exit Screen ASROCK UEFI SETUP UTILITY TOMORROW S TECHNOLOGY TODAY Save Changes and Exit When you select this option it will pop out the following message Save con guration changes and exit setup Select OK to save the changes and exit the UEFI SETUP UTILITY Discard Changes and Exit When you select this option it will pop out the following message Discard changes and exit setup Select OK to exit the UEFI SETUP UTILITY without saving any changes Discard Changes When you select this option it will pop out the following message Discard changes Select OK to discard all changes Load UEFI Defaults Load UEFI default values for all the setup questions F9 key can be used for this operation Launch EFI Shell from filesystem device Attempts to Launch EFI Shell application Shell64 efi from one of the available lesyst

Asrock A75 Pro4

Contents

Download Pdf Manuals

Related Search

Related Contents