Da-Lite Advantage Electrol 50" x 80"
Contents
1. GROUND 240VOLT AC 50HZ 240 VOLT WIRING DIAGRAM FOR STANDARD POWER SOURCE WALL SWITCH GREEN YELLOW GROUND Da Lite offers two styles of 240 volt wall switches for standard operation Please see wiring diagram included in wall switch box included with screen BLACK WHITE FRONT OF BACK OF WALL WALL SWITCH SWITCH me BLACK 5 12 VOLT SCREEN FIGURE 6 TRIGGER ON PROJECTOR FIGURE 7 CAUTION THE PROJECTOR MUST BE TURNED OFF BEFORE CONNECTING THE TRIGGER WIRES TO THE PROJECTOR FAILURE TO DO SO MAY DAMAGE THE CONTROLLER 1 Use 2 conductor 20 24 gauge wire to extend the low voltage connection from the projector s 5 12 volt screen trigger output to the length required to reach the VPI When extending the low voltage connection from the projector s screen trigger output be sure to maintain the proper polarity The red wire from the VPI is the signal and the black wire from the VPI is the ground 2 Connect the wires from the VPI that are labeled Low Voltage Connection to the end of the extended screen trigger wires above 240V WIRING DIAGRAM WITH OPTIONAL BUILT IN OPTIONAL IR AND RF LOW VOLTAGE CONTROL REMOTE CONTROL LOW VOLTAGE WALL SWITCH UP DI N GND 5V BROWN2. The Da Lite Difference Instruction Book for ADVANTAGE ELECTROL ee TN DA LITE es DA LITE SCREEN COMPANY INC 3100 North Detroit Street Post Office Box 137 Warsaw Indiana 46581 0137 Phone 574 267 8101 800 622 3737 Fax 574 267 7804 Toll Free Fax 877 325 4832 www da lite com e mail info da lite com IMPORTANT SAFETY INSTRUCTIONS When using your video equipment basic safety precautions should always be followed including the following 1 Read and understand all instructions before using 2 Position the cord so that it will not be tripped over pulled or contact hot surfaces 3 If an extension cord is necessary a cord with a current rating at least equal to that of the appliance should be used Cords rated for less amperage than the appliance may overheat 4 To reduce the risk of electric shock do not disassemble this appliance Contact an authorized service dealer when repair work is required Incorrect reassembly can cause electric shock when the appliance is used subsequently 5 The use of an accessory attachment not recommended by the manufacturer may cause a risk of fire electric shock or injury to persons SAVE THESE INSTRUCTIONS PRE INSTALLATION 1 Carefully unpack case from shipping carton DO NOT unpack fabric and roller assembly yet 2 Make sure to recheck measurement of case for proper installation clearance 3 Remove any protective foam or tape from case CASE INSTALLAT
3. HOT GREEN 240VAC 50HZ 3 POSITION GROUND MUST BE CONNECTED TO BUILDING GROUND GROUND TO CASE DRY CONTACTS ILT RJ9 PIN OUTS IMPORTANT NOTE The wall switch is REQUIRED to make any limit switch adjustments EVEN if a third party control a system is used Therefore it is advised to wire the PrE switch or provide a 4 conductor connection that Is A vine accessible FIGURE 8 TROUBLESHOOTING Visit www da lite com products tutorials php to find installation and troubleshooting tutorials You will also find a link to Live Chat for interactive support and you can contact us by email at info da lite com or by phone at 800 622 3737 or 574 267 8101 with any troubleshooting questions SYMPTOM 1 Screen will not operate Motor does not hum 2 Screen does not stop at correct position 3 Noise NOTE Screen will operate with a low pitched hum 4 Coasting 5 Fabric hangs crooked Incorrect line voltage b Blown fuse Tripped circuit breaker d No power to operating switch or junction Power at junction box e Thermal overload tripped f Broken wire in the down or up position g Defective motor limit switch or capacitor h Capacitor burned out Limit switch out of adjustment a Squeaking rubber end plug rubbing on motor b Grinding Foreign object in screen rubbing on roller or fabric c Gea
4. approximately two feet then lower again Repeat until desired picture surface position is attained WHITE ADJUSTMENT KNOB DOWN MOTOR MOUNT BRACKET BLACK ADJUSTMENT KNOB UP FIGURE 1 SCREEN ADJUSTMENT FOR 220 240V SCREENS WITHOUT BUILT IN LOW VOLTAGE CONTROL Surface travel is stopped automatically in the fully opened and closed positions by limit switches that are properly adjusted at Da Lite Should it be necessary to adjust for more or less drop of picture proceed in the following manner NOTE Use a screw driver or 5 32 Allen wrench to make adjustments MORE SCREEN DROP 1 Place operating switch in down position 2 When the screen stops turn the white down limit knob Fig 2 one turn counterclockwise Test by raising picture surface approximately two feet then lower again Repeat until desired picture surface position is attained LESS SCREEN DROP 1 Raise picture surface approximately two feet above desired level 2 Place operating switch in off position 3 Turn the white down limit knob Fig 2 one turn clockwise Test by N MOTOR POWER CONNECTOR MOTOR raising picture surface KNOB DOWN approximately two feet then lower again Repeat until desired picture surface position is attained MOTOR MOUNT BRACKET RED ADJUSTMENT KNOB UP FIGURE 2 SCREEN ADJU
5. apply to equipment showing evidence of misuse abuse or accidental damage or which has been tampered with or repaired by a person other than authorized Da Lite personnel Da Lite s sole obligation under this warranty shall be to repair or to replace at Da Lite s option the defective part of the merchandise Returns for service should be made to your Da Lite dealer If it is necessary for the dealer to return the screen or part to Da Lite transportation expenses to and from Da Lite are payable by the purchaser and Da Lite is not responsible for damage in shipment To protect yourself against damage or loss in transit insure the product and prepay all transportation expenses THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING WARRANTIES AS TO FITNESS FOR USE AND MERCHANT ABILITY Any implied warranties of fitness for use or merchantability that may be mandated by statute or rule of law are limited to the one 1 year warranty period This warranty gives you specific legal rights and you may also have other rights which vary from state to state NO LIABILITY IS ASSUMED FOR EXPENSES OR DAMAGES RESULTING FROM INTERRUPTION IN OPERATION OF EQUIPMENT OR FOR INCIDENTAL DIRECT OR CONSEQUENTIAL DAMAGES OF ANY NATURE In the event that there is a defect in materials or workmanship of a Da Lite product you may contact our Sales Partners at PO Box 137 Warsaw IN 46581 0137 574 267 8101 800 622 3737 IMPORTANT TH
6. position slide the 3 position switch to the off center position The down limit switch is now set 5 To adjust the up limit switch slide the 3 position switch to the up position Press and hold the up button to run the screen up to the desired stop position Release the button to stop the screen DO NOT PUSH THE STOP BUTTON 6 When the screen is in the desired up position slide the 3 position switch to the off center position The up limit switch is now set 7 To test limit switch setting make sure the 3 position switch is in the off center position Press and release the up or down button on the wall switch to operate the screen 8 Replace switch and cover plate on the wall NOTE If stop button is pressed the wall switch will reverse direction To correct this press the stop button again This will reset the switch You will have to re set both the up and the down limit settings IMPORTANT NOTE The wall switch is REQUIRED to make any limit switch adjustments EVEN if a third party control system is used Therefore it is advised to wire the switch or provide a 4 conductor connection that is accessible ADVANTAGE ELECTROL INSTALLATION VARIABLE POSITION MOUNTING BRACKET MOTOR END AUDIENCE SIDE 3 8 THREADED ROD NOT INCLUDED ATTACHED TO ELECTRICAL MOUNTING BRACKET JUNCTION BOX SELF TRIMMING _ FINISHED FLANGE CEILING 7 3 4 SEE DET
7. 4 20 nuts securely Complete electrical hook up by snapping motor wire connector into case connector Carefully remove paper and tape from roller assembly DO NOT use a knife or sharp object to cut tape you will damage the screen Pull orange string Test installation by running screen up and down a few times Be prepared to stop screen Standard Duty Cycle 1 MIN ON 3 MIN OFF Re install access door Procedure is reverse of removal step 1 1 SCREEN ADJUSTMENT FOR 120V SCREENS WITHOUT BUILT IN LOW VOLTAGE CONTROL Surface travel is stopped automatically in the fully opened and closed positions by limit switches that are properly adjusted at Da Lite Should it be necessary to adjust for more or less drop of picture proceed in the following manner Remove two screws to remove access door NOTE Use a screw driver or 5 32 Allen wrench to make adjustments MORE SCREEN DROP 1 Place operating switch in down position 2 When the screen stops turn the white down limit knob Fig 1 one turn counterclockwise Test by raising picture surface approximately two feet then lower again Repeat until desired picture surface position is attained LESS SCREEN DROP 1 Raise picture surface approximately two feet above desired level MOTOR POWER CONNECTOR MOTOR 2 Place operating switch in off position 3 Turn the white down limit knob Fig 1 one turn clockwise Test by raising picture surface
8. AIL 3 8 THREADED ROD NOT SUPPLIED HANGER BRACKET DETAILA ADVANTAGE ELECTROL INSTALLATION FOR 120V SCREENS 120V WIRING DIAGRAM FOR STANDARD WALL SWITCH JUNCTION BOX LOCATED IN LEFT ENDCAP A SINGLE SWITCH CANNOT USED TO OPERATE MORE THAN ONE SCREEN CONTACT THE FACTORY FOR FURTHER INFORMATION SPDT SWITCH WITH CENTER OFF THIS SWITCH CAN NOT BE USED WITH LVC 120V WIRING DIAGRAM WITH OPTIONAL BUILT IN VIDEO PROJECTOR INTERFACE CAUTION THE PROJECTOR MUST BE TURNED OFF BEFORE CONNECTING THE TRIGGER WIRES TO THE PROJECTOR FAILURE TO DO SO MAY DAMAGE THE CONTROLLER Use 2 conductor 20 24 gauge wire to extend the low voltage connection from the projector s 5 or 12 volt screen trigger output to the length required to reach the VPI When extending the low voltage connection from the projector s screen trigger output polarity does not matter red and black wires from the VPI are interchangeable IMPORTANT NOTE The wall switch is REQUIRED to make any limit switch adjustments EVEN if a third party control system is used Therefore it is advised to wire the switch or provide a 3 conductor connection that is accessible 3 conductor 20 24 gauge wire can be used in place of the supplied RJ 14 cable to connect the wall switch Connect the BUS terminals on the wall switch to the corresponding BUS terminals on the splitter board AC COMMON AC HOT 120VAC 60HZ 1 AMP BLA
9. CK YELLOW FRONT OF WALL SWITCH BACK OF WALL SWITCH A 5 12 VOLT SCREEN TRIGGER ON PROJECTOR FIGURE 3 RJ 22 JACK RJ 22 OUTPUT bown_ _ DRY CONTACTS COMMON Bus jH By BUS RJ 45 RECEPTACLE MODULE GREEN GROUND 4 BLACK HOT WHITE COMMON GROUND MUST BE CONNECTED TO BUILDING GROUND POWER INPUT 120VAC 60HZ FIGURE 4 ADVANTAGE ELECTROL INSTALLATION FOR 120V SCREENS RJ 14 PIN OUTS RJ 22 PIN OUTS 120V WIRING DIAG RAM TAB IS FACING UP TAB IS FACING UP WITH OPTIONAL BUILT IN LOW VOLTAGE CONTROL RJ 45 PIN OUTS TAB IS FACING UP RJ 45 RECEPTACLE RJ 45 JACK FRONT OF BACK OF WALL SWITCH WALL SWITCH POWER WIRE 3 conductor 20 24 gauge wire can be used in place of the supplied RJ 14 cable to connect the wall switch Connect the BUS terminals on the wall switch to the corresponding BUS terminals on the splitter board IMPORTANT NOTE GREEN GROUND L The wall switch is REQUIRED to make any limit switch BLACK HOT 7 adjustments EVEN if a third party control system is WHITE COMMON GROUND MUST BE used Therefore it is advised to wire the switch or CONNECTED TO provide a 3 conductor connection that is accessible POWER INPUT 120VAC 60HZ ADVANTAGE ELECTROL INSTALLATION FOR 220 240V SCREENS 240V WIRING DIAGRAM WITH OPTIONAL BUILT IN VIDEO PROJECTOR INTERFACE BROWN DOWN BROWN HON BLUE COMMON BLUE COMMON BLACK UP GREEN E
10. ION Remove 2 screws to open junction box Hang case and attach to support structure with bolts See suggested methods of installation on page 5 Tighten bolts until trim flange is flush with ceiling NOTE For proper operation screen assembly must be level after installation Install electrical connections that applies to your unit Make sure to review the wiring diagram for proper hook up NOTE Must be installed in accordance with the requirements of the Local Building Codes the Canadian Electrical Code CEC CAN CSA C22 1 and the National Electric Code NEC NFPA 70 Replace junction box cover and secure with 2 screws SCREEN AND ROLLER ASSEMBLY INSTALLATION If your screen was shipped with the motor and roller already installed proceed to step 6 1 Remove access door First remove the 2 screws from the ends Be sure to support the door during this step to avoid injury Then lift the door slightly and pull away from the edge of the case Carefully unpack screen and roller assembly Leave packing paper on roller To install screen and roller assembly insert the motor end into the motor mount bracket as shown in Fig 1 Loosen but do not remove two 1 4 20 nuts securing pin end bracket stage left to the case housing Slide the bracket towards the end of the case Insert the motor end square shaft into the motor end bracket and secure with the clip Insert the tip of the roller pin into the bracket and position Tighten the 1
11. IS WARRANTY SHALL NOT BE VALID AND DA LITE SHALL NOT BE BOUND BY THIS WARRANTY IF THE PRODUCT IS NOT OPERATED IN ACCORDANCE WITH DA LITE S WRITTEN INSTRUCTIONS Keep your sales receipt to prove the date of purchase and your original ownership Printed in U S A 84214 Rev 9 11
12. STMENT FOR 120V SCREENS WITH A BUILT IN LOW VOLTAGE CONTROL OR VPI 1 Locate the wall switch and remove the cover plate from the 3 button wall switch and remove the switch from the junction box 2 Locate the two tactile buttons on the back of the switch They are square silver with black round buttons See Figure 4 VPI or Figure 5 LVC for diagram 3 To adjust the down limit switch press and hold the down tactile button until the LED on back of switch turns solid red This will put the motor in limit set mode Turn the wall switch over and use the down button on front of switch Press and hold until the desired travel position is reached If you travel to far down you can press the up to move the screen upward If you press and let go of either up or down button the motor will do a small jog in that direction for finer adjustment of screen Once desired position is reached turn switch over press and hold down tactile button until the LED on back of switch blinks red twice The down limit is now set 4 To adjust the up limit switch press and hold the up tactile button until the LED on back of switch turns solid green This will put the motor in limit set mode Turn the wall switch over and use the up button on front of switch Press and hold until the desired travel position is reached If you travel to far up you can press the down to move the screen downward If you press and let go of either up or down button the motor will do a small jog in th
13. at direction for finer adjustment of screen Once desired position is reached turn switch over press and hold up tactile button until the LED on back of switch blinks green twice The up limit is now set 5 To test limit switch setting press and release the up or down button on the wall switch to operate the screen 6 Replace switch and cover plate on the wall NOTE If the screen is in limit set mode and no buttons are pushed for 20 seconds the LED on the back of the wall switch will turn off the motor will return to run mode and no changes will be saved If this occurs return to step 3 for down limit adjustment or step 4 for up limit adjustment IMPORTANT NOTE The wall switch is REQUIRED to make any limit switch adjustments EVEN if a third party control system is used Therefore it is advised to wire the switch or provide a 3 conductor connection that is accessible SCREEN ADJUSTMENT FOR 220V 240V SCREENS WITH A BUILT IN LOW VOLTAGE CONTROL 1 Remove the cover plate from the 3 button wall switch and remove the switch from the junction box 2 Locate small 3 position switch on back of wall switch See Figure 5 for 120V screens or Figure 8 for 220 240V screens 3 To adjust the down limit switch slide the 3 position switch to the down position Press and hold the down button to run the screen down to the desired stop position Release the button to stop the screen DO NOT PUSH THE STOP BUTTON 4 When the screen is in the desired down
14. r noise a Defective brake a Screen not installed properly b Fabric has backed up inside case c Fabric is damaged A SOLUTION Verify 115 125V or 220 240V If insufficient voltage rewire incoming electric line Replace fuse Reset circuit breaker Check above Tighten all loose wire connections Correct any improper connections Down Position Check for power across black and white leads Up Position Check for power across red and white leads Let motor cool down for 15 minutes Try again Check for continuity Cut off old splice and reconnect Replace motor assembly NOTE Motor is a sealed assembly Replace motor assembly See Screen Adjustment section Center roller in case Remove Replace motor assembly Replace motor assembly Check for level and plumb Adjust down limit switch slowly until roller is exposed and wrinkle comes out then readjust for proper drop Replace fabric LIMITED ONE YEAR WARRANTY ON DA LITE PRESENTATION PRODUCTS Da Lite Screen Company Inc warrants its products to the original purchaser only to be free from defects in materials and workmanship for a period of one 1 year from the date of purchase by the original purchaser provided they are properly operated according to Da Lite s instructions and are not damaged due to improper handling or treatment after shipment from the factory This warranty does not
Download Pdf Manuals
Related Search