Revo REVDN650-1 surveillance camera
Contents
1. 1 TABLE OF CONTENTS INTRODUCTION ereccion 4 CAMERA CONNECTIONS coronan 5 INSTALLATION mm nnn nnn nnn nnn 6 LENS ADJUSTMENT ona 7 DC AUTO IRIS LENS nnn ee eor reo nnn nnn 8 OPERATING CAMERA eoo eno en reno nn enn 8 CAMERA ADJUSTMENT eoo re o nr reno nnn enn 9 EXTERNAL DIMENSION eoo eroe nn eon 16 SPECIFICATIONS eo erro reo nnn nnn nnn nnn nen 17 INTRODUCTION The camera provided high quality image using SONY Wide Dynamic 1 3 CCD and digital signal processing LSIs Features 1 3 Super HADII PS 960H CCD Super high resolution of 650TV lines 0 4 lux Color 0 04 lux B W 0 001 lux Low Shutter F1 4 Sensitivity Auto Electronic Shutter 1 60 1 50 1 100 000 and manual electronic shutter modes 1 60 1 50 1 10 000 On Screen Display OSD Auto and Manual white balance modes Support Line Lock external synchronization Digital PTZ Digital Effect H V reverse 180 degree rotate inverse freeze 2D NR 3D NR DNR Demo Back Light Compensation Back Light Masking MAX 15 area Excessive High Light Compensation Wide Dynamic Range x512 Various Detection Method zone detection motion trace face trace mine area absent detection cross object counting2. Load Default Setup gt Yes Load default to current configuration and return to previous menu gt No No operation and return to previous menu 17 EXTERNAL DIMENSION 99 0 INNER 993 0 9 N LO N e 1 A 0146 3 0 1 in 2 5mm thick Window Size impact resistant P C LEXAN 3 93 in 10cm diameter Cable Entry One 1 opening holes Weight Unit 1 54 Ib 700 g Shipping 2 11 Ib 960 kg SPECIFICATIONS MODEL NTSC PAL Power Power source DC 12V AC 24V 10 Power consumption 4 5 Watts Image sensor 1 3 Super HADII PS 960H CCD Total pixels 1028 H x508 V 1028 H x596 V Effective pixels 976 H x494 V 976 H x582 v Scanning system 2 1 interlace Scanning frequency 15 734KHz H x59 94Hz V 15 625KHz H x50Hz V Sync System Internal Line lock Resolution 650TVL Min illumination 0 4 Lux COLOR 0 04 Lux B W 0 001 Lux Slow shutter Video output 1 0 Vp p 75 ohm composite S N ratio 50dB AGC OFF Camera control RS485 Faxtrax Pelco D Pelco P Lens 2 8mm 12 0mm F 1 4 D amp N DC IRIS Vari Focal Lens White Balance Auto CRS Push amp Hold Indoor Outdoor FL User Auto Exposure Auto Manual Shutter Flickerless Low Light Control Offset Add AGC Off Low Middle High Shutter Speed 1 60 1 10 000
3. Low Mid High 3 2D NR Select 2D noise reduction level 0 6 gt 2D NR Noise reduction on a frame 4 3D NR Select 3D noise reduction level 0 31 gt 3D NR Noise reduction through the several frame 5 DNR Demo Select DNR Demo Display On Off using the Left and Right Buttons None DNR Effect DNR Applied Display Display lt Effect Special gt 1 d Effect Digital Effect Select digital Flip Rotate state Off Rotation Mirror V Flip 2 Nega Select negative color state on off 3 d PTZ Digital Pan Tilt Zoom Adjust d PTZ gt Func Press the Enter button to turn digital zoom on off gt Zoom Use the Left and Right buttons adjust to digital zoom 0 255 gt Pan amp Tilt Press the Enter button to access the Pan amp Tilt W Usethe Left and Right buttons adjust to digital pan m Use the Up and Down buttons adjust to digital tilt m Press the Enter button to exit gt PT Reset Pan amp Tilt Reset Press the Enter button to reset digital pan and tilt 4 Freeze Select the still mode on off 5 Frame Control Select term of refresh rate for output video This function is useful to reduce the recording to data storage gt Func Select frame control mode to ON OFF and Auto 14 m Auto mode When motion is not detected output video is being refresh in configured interval And when the motion is detected output video is switched to real time video m ON Always refresh in configured interval m OFF Alw
4. Select mask area 1 15 2 Func Select mask function Privacy BLM Both Off Privacy Area to screen on the display gt BLM Back Light Mask m Selected BL Mask area that will be except of the auto exposure 11 m f there is a high light installed in a limited environment such as an apartment parking garage or gas station entrance removing the high light makes it possible to view car license plates efficiently gt Both Privacy function and BLM function on gt Off Function off 3 Edit Mask area edit gt Edit mode take effect during Func not Off Size adjust the size of the Privacy and BLM mask area Posi adjust the position of the Privacy and BLM mask area Tilt adjust tilting of Privacy and BLM mask area Color Select Privacy and BLM mask 0 14 Transparency Select Privacy mask transparency Default 3 0 3 Mosaic Select Privacy and BLM mask mosaic On Off Adj Mosaic Adjust Privacy and BLM mask mosaic level 0 31 lt Detection gt 1 Func Detection function selection gt OFF Detection function off gt Zone Area motion detection mode m Zone Select Motion detection zone Zone1 4 W Func Select Motion detection on off W Size Press Enter button to adjust the size of the Motion detection area m Posi Press Enter button to adjust the position of the Motion detection area W Link Zoom Select Motion detection with D PTZ function that On Off When the motion triggered in the area zoom
5. entrance counting Day amp Night Auto Manual External Filter delay Various Alarm Method Period Snooze Polarity Select Privacy Mask or Mosaic MAX 15 area 4 point polygonal transparency Scene Change Detection Sens Up x32 White Pixel Remove Frame Control Auto 1 7 sec System Lock 4 Digit password RS 485 Remote camera control F1 4 D amp N DC iris vari focal lens Operates in 12VDC or 24VAC User Certified Listed Class 2 power source only CAMERA CONNECTIONS Connection Cable Description ojo He Description RED AC24V DC12V WHITE AC24V DC12V ORANGE ADKEY BROWN GND BLUE RS485 GREEN RS485 YELLOW ALARM OUT GRAY DN EXT IN BLACK amp WHITE DN EXT OUT BLACK GND SKY BLUE UTP optional PINK UTP optional 1 External Day Night Control To select Day Night mode using external equipment by connecting control lines to the appropriate terminals gt DAY amp NIGHT OUTPUT Black amp White Is the camera function that can turn on an external IR LED Lamp by detecting the sensitivity on the AGC level when the D amp N mode is set AUTO on the OSD menu of the camera Black amp White O 5V 10mA IR LED ON NIGHT gt DAY amp NIGHT EXTERNAL INPUT Gray Is the camera function that can be switched to DAY Mode or NIGHT mode by receiving the D amp N on off signal from external light sensor or IR LED LAMP This needs the D a
6. 1 50 1 10 000 Auto 1 100 000 Auto 1 100 000 BLC EHLC AUTO SPOT ZONE BLM Camera Title Alpha Numeric F Display On Off Cam ID Title U DNR 2DNR 3D NR Gain Adjust DNR Demo N Day amp Night Auto Day Night Ext C Video Analytics Zone Motion trace Face trace Minefield Absent Cross T y Entrance Scene Change Detection Privacy zone Max 15 Tilt Color Transparency Mosaic General O Effect V Flip Mirror Rotation Nega amp Posi Freeze Sharpness N Sense up x32 Sharpness 0 15 steps Cam ID 001 255 WDR WDR x512 Level Adjust D Zoom x256 D Zoom D PTZ Support Bad Pixel Adj Done Max 64 point Detected pixel display System Lock Lock Unlock need Password input when Locked Frame Control Auto Off 7Sec Use for saving storage Other Function Admin Password Alarm Setting Period Snooze Polarity Power input Terminal block Video output BNC UTP optional Lens mount Fixed Mount Connec Lens 2 8mm 12 0mm F 1 4 D amp N DC IRIS Vari Focal Lens tor Operating Temp 10 C to 50 C amp etc Operating humidity Less than 90 External dimension 146 W x 114 H x Weight 700g 19 MEMO WDR Super High Resolution Day amp Night Color Camera PRINTED IN KOREA 50302586B
7. C 8 32 x 0 75 LENS ADJUSTMENT Field of view Adjust setting 4 8 from Telephoto T to wide W field of View o mo z z Focus Adjust lens focus from near N to infinity Adjust Focus Adjust Angular Field View DC AUTO IRIS LENS 2 6 6mm 4 9mm 2 8 12mm 6 50mm Image Size 1 3 CCD 1 3 CCD 1 3 CCD 1 3 CCD Focal Length 2 6 6 0mm 5 4 0 9 0mm 5 2 8 12mm 5 6 0 50mm 5 APERET 1 16 5 1 1 6 5 1 1 4 5 1 1 6 6 9 Ratio Angular DIAGONAL DIAGONAL DIAGONAL DIAGONAL Field of View 2 6mm 134 6 4mm 92 4 2 8mm 119 9 6mm 58 6 Degree 6mm 59 2 9mm 39 2 12mm 28 8 50mm 7 1 MEE Black Control EE White Control LENS Red Drive Green Drive BEE Brown Damper Yellow Red Damper LENS LENS perk MIA Brown IR filter out Yellow Drive Orange Drive OPERATING CAMERA D Enter Button Up Button Down Button Left Button 9 Right Button Spot Video Output UTP Optional CAMERA ADJUSTMENT lt White Balance gt 1 Auto Auto White Balance AWB mode 1800 K 10500 K 2 Push Hold Push amp Hold Mode gt To find the Optimal setting for the current luminance environment in this mode set the direction towards a sheet of white paper and select Hold and press enter button If the environment changes readjust it 3 CRS Mode Color Rolling Suppression Decrease color rolling effect This operation take some time about 10 seconds and us
8. INSTRUCTION MANUAL WDR Super High Resolution Day amp Night Color Camera Please read this manual thoroughly before use and keep it handy for future reference WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE DO NOT INSERT ANY METALLIC OBJECT THROUGH VENTILATION GRILLS CAUTION CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICABLE PARTS INSIDE REFFER SERVICING TO QUALIFIED SERVICE PERSONNEL EXPLANATION OF GRAPHICAL SYMBOLS The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the product PRECAUTIONS Safety Should any liquid or solid object fall into the cabinet unplug the unit and have it checked by qualified personnel before operating it any further Unplug the unit from the wall outlet if it is not going to be used for several days or more To disconnect the cord pull it out by the plug Never pull the cord itself Allow adequate air circulation to p
9. R WILL BE REQUIRED TO CORRECT THE INTERFERENCE AT HIS OWN EXPENSE CAUTION CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE COULD VOID THE USER S AUTHORITY TO OPERATE THE EQUIPMENT THIS CLASS A DIGITAL APPARATUS COMPLIES WITH CANADIAN ICES 003 CET APPAREIL NUMERIQUE DE LA CLASSE A EST CONFORME A LA NORME NMB 003 DU CANADA CE COMPLIANCE STATEMENT WARNING This is a Class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures IMPORTANT SAFETY INSTRUCTIONS OOP QIN SS eo 10 11 12 13 14 15 16 Read these instructions Keep these instructions Heed all warnings Follow all instructions Do not use this apparatus near water Clean only with dry cloth Do not block any ventilation openings Install in accordance with the m anufacturer s instructions Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat Do not defeat the safety purpose of the polarized or grounding type plu g A polarized plug has two blades with one wider than the other A gro unding type plug has two blades and a third grounding prong The wid e blade or the third prong are provided for your safety If the provided p lug does not fit into your outlet consult an electrician for replacement o f the obsolete
10. and move to the area with D PTZ gt Motion Trace Motion trace mode on W Tracks an object through a scene and generates an alarm gt Face Trace Face Trace mode on m Tracks face through a scene and generate an alarm W Sens Down lower value is more widen the scope to judge face 0 127 W Min Size Minimum face size configuration 0 minimum face size is to none The result of face trace can be inaccuracy Mine By this function User can draw motion detection area with free dotting W Set Mine Press the Enter button to Set Mine mode lt gt Move Mine Zone move using the Left and Right buttons UP Set Mine Zone setting using the Up button DN Clr Mine Zone clear using the Down buttons ENT End Press the Enter button to set Mine mode end W CirAll Press the Enter button to set Mine area clear m Display Select Mine Display On Off 12 gt Absent Press the Enter button to Absent detection mode Detect object appeared or removed the scene m Sens Down Adjust sensitivity of Absent check 0 255 In low luminance environment the accuracy is down of the result Because object color is effect to auto exposure the accuracy is down of the result If the object is too big the accuracy is down of the result Cross Cross counting mode W Zone Select Cross Zone using the Left and Right buttons Zone 1 Zone 2 Size Adjust the size of the Cross zone Posi Adjust the position of the Cross z
11. ays real time video gt Renewal sec Select an interval between two frame When object start moving The output video possible to cut a little time 6 ScnChg Unfoc Select scene change unfocus detection On Off Inform that whether scene have been changed or not Detect breaking or changing in the watching scene Spray Screen Camera Changing Scene gt This function is linked with alarm out In low luminance environment the accuracy is down of the result In very low luminance environment operation is not be performed It is not be performed when moving object is exist lt System Setup gt 1 Cam Info Camera basic information display gt Cam ID Baud rate Protocol Firmware Ver CCD Type Lens Type 2 General Setup System Lock Configuration Lock W When system lock is set to Lock User must to input 4 character password to enter OSD menu Default password is 0000 gt Change PID Change the administrator s password W Move cursor with OSD Key and Press Enter to input the character Comm RS 485 Communication Press the Enter button to access the Comm m Cam ID Select the camera ID 001 255 W Baud Rate Select serial communication speed 2400 4800 9600 19200 W Protocol RS 485 protocol COMMAND FASTRAX PELCO D Pelco D Title Edit camera title 15 Title Site O A w lt gt ENT Del B A Title B Delete character C Character table M D Command line abcdef
12. er can stop this operation by pressing enter button gt When CRS Mode is on color tone can be weak 4 Outdoor Set color temperature to outdoor 6300 K 5 Indoor Set color temperature to indoor 3200 K 6 FL Fluorescent Light Set color temperature to fluorescent light fixed gain 7 User User Set White Balance Adjust red or blue gain gt R R GAIN Adjust R GAIN value 0 255 gt B B GAIN Adjust B GAIN value 0 255 lt Auto Exposure gt 1 SHT s Electronic Shutter Select Shutter mode gt Auto 1 60 1 50 1 100 000 Auto run Manual 8 step from 1 60 1 50 1 10 000 2 FLC Flicker less Flicker less On Off 3 AGC Auto Gain Control AGC Gain Off Low Middle High 4 Sens Up Slow Shutter Maximum Slow Shutter select x2 x32 and Off 5 Offset Add Force the picture to turn up at low luminance environment lt BLC WDR gt 1 Normal AE BLC WDR function off 2 WDR Wide Dynamic Range Wide dynamic range mode on 3 EHLC Excessive High Light Compensation EHLC mode on excessive lighting compensation is performed when the weighting on the high brightness side is increased 4 Auto Auto Weighting BLC Auto weighting BLC on 5 Spot User Setting BLC area Spot metering mode on gt Posi OSD mode to adjust the position of the spot metering area gt Size OSD mode to adjust the size of the spot metering area 6 Zone Preset BLC area Fixed metering area mode 1 9 lt Mask gt 1 Mask
13. ghijklm C Clear Clear Title nopqrstuvwxyz 0123456789 ABCDEFGHIJKLM NOPQRSTUVWXYZ Cancel Cancel editing Accept Save Title Clear Cancel Accep D gt Display Display item select W Cam ID Camera ID display On Off W Title Title display On Off gt Alarm Period a Alarm Out Event WD 2 Time Snooze W Period Alarm out period 5sec 10sec 20sec 30sec 1min 5min Cont W Snooze Alarm out snooze Off 5sec 10sec 20sec 30sec 1min 5min m Active pol Alarm output active state configuration Low High gt System Init m Cancel Back to General Setup Menu W Confirm Initialize all data Factory Default 3 Lens gt Iris DC Video Manual Lens selected Iris adjust AE Speed m DC lensand video lens can adjust AE Speed gt Normal AE Ref Auto Exposure Reference Level Press the Enter button to access the AE Ref W RefLvl Adjust AE base reference level gt WDR Ref Press the Enter button to access the WDR Ref W Ref Lvl Adjust the WDR long time control Base Reference Level 4 LLC Line Lock Control Press the Enter button to access the Line Lock mode gt Func Select Line Lock function On Off using the Left and Right buttons gt Phase Adjust Line Lock sync phase using the Left and Right buttons 0 100 16 Activate only AC power inputted 5 White Pixel Det Exe Press Enter button to turn White Pixel Compensation mode Start W ENT to Adj Press Enter button to star
14. mp N Mode to be set to External on the OSD menu of the camera to work GNO el Close contact NIGHT DAY amp NIGHT INPUT Open contact DAY 2 Alarm Out gt Motion detection signals are output through this port YELLOW AND GND gt Active state is configurable 3 Power Input Terminal RED amp WHITE DC Power is recommended to use the DC power supply that can support inrush current over 0 75A 4 Camera Control gt GREEN RS 485 gt BLUE RS 485 5 UTP optional gt Video signal through out the UTP Cable SKY BLUE amp PINK 7 INSTALLATION 1 Loosen the four torx screws located midway up the front of the housing leave the screws intact in the front portion Fig 1 2 Drill the mounting location using the bottom of the housing as a Drilling guide label Fig 3 3 Attach the housing to the ceiling using suitable fasteners M6x35 tapping screws are supplied only use if they are suitable Fig 3 4 Closing the housing using the loosen torx screws Fig 2 Torx screws M5x10 4x Torx screws M5x10 4x Seal around i the housing Figure 1 Figure 2 base tightly L abel is attached at the bottom CEILING WALL 4 Drilling Guide Label Mounting Screw M6X35 4x e Figure 3 Rubber Washers 4x MOUNTING HOUSING TO AN ELECTRICAL BACK BOX The housing can also be mounted on a 4s electrical box Rubber _S Washers 4x 3 J d A Torx screws UN
15. one Direction Select Cross Direction Alarm Cnt Set alarm out cross count Alarm count number is delaying number before output alarm Reset Cnt Cross count reset If object is passing so fast through the two area counting is not operating In this case adjust to expand space between two area or decrease size of area If passing object is too long counting result can be inaccuracy In this case adjust to expand space between two area or adjust to decrease size of area If two object passing the area in the same time the results can be inaccuracy Entrance Entrance counting mode The object move in through the entrance counting number increases m Size Press Enter button adjust the size of the Entrance zone W Posi Press Enter button adjust the Position of the Entrance zone m Alarm Cnt Set alarm out entrance count Alarm count number is delaying number before output alarm W Reset Cnt Entrance count reset 2 Sens Down Adjust to Motion Sensitivity using left right Buttons 13 Crossing object is not considered Several objects will not be detected If the distance is increases between the camera and entrance the result can be inaccuracy Camera Installed at the ceiling Crossing object is none One object is passing Several Object Crossing Object The distance is too long lt Picture DNR gt 1 Sharpness Adjust sharpness of outlines 0 15 2 Resolution Select high resolution mode
16. outlet Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from th e apparatus Only use attachments accessories specified by the manufacturer Use only with the cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart is used use cau tion when moving the cart apparatus combination to avoid injury from ti p over Unplug this apparatus during lightning storms or when unused for long periods of time Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power su pply cord or plug is damaged liquid has been moisture does not oper ate normally or has been dropped CAUTION THESE SERVICING INSTRUCTIONS ARE FOR USE B Y QUALIFIED SERVICE PERSONNEL ONLY TO REDUCE THE RIS K OF ELECTRIC SHOCK DO NOT PERFORM ANY SERVICING OT HER THAN THAT CONTAINED IN THE OPERATING INSTRUCTION S UNLESS YOU QRE QUALIFIED TO DO SO Use Certified Listed Class 2 power source only CONTENTS OF PACKAGE The package contains the following Camera in Housing 1 Instruction Manual This Document 1 Accessory Kit for Installing 1 Drilling guide label
17. revent internal heat build up Do not place the unit on soft surfaces rugs carpets sofas etc or near materials curtains draperies that may block the ventilation holes Height and vertical linearity controls located on the rear panel are for special adjustments by qualified personnel only Installation Do not install the unit in an extremely hot or humid place or in a place subject to excessive dust mechanical vibration The unit is not designed to be waterproof Exposure to rain or water may damage the unit Cleaning Clean the unit with a slightly damp soft cloth Use a mild household detergent Never use strong solvents such as thinner or benzine as they might damage the finish of the unit Retain the original carton and packing materials for safe transport of this unit in the future FCC COMPLIANCE STATEMENT INFORMATION TO THE USER THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS FOR A CLASS A DIGITAL DEVICE PURSUANT TO PART 15 OF THE FCC RULES THESE LIMITS ARE DESIGNED TO PROVIDE REASONABLE PROTECTION AGAINST HARMFUL INTERFERENCE WHEN THE EQUIPMENT IS OPERATED IN A COMMERCIAL ENVIRONMENT THIS EQUIPMENT GENERATES USES AND CAN RADIATE RADIO FREQUENCY ENERGY AND IF NOT INSTALLED AND USED IN ACCORDANCE WITH THE INSTRUCTION MANUAL MAY CAUSE HARMFUL INTERFERENCE TO RADIO COMMUNICATIONS OPERATION OF THIS EQUIPMENT IN A RESIDENTIAL AREA IS LIKELY TO CAUSE HARMFUL INTERFERENCE IN WHICH CASE THE USE
18. t White Pixel Compensation start m Proc Process to find white pixel W Done Process ended gt Det Count Result of white pixel detection gt Func Select erasing white pixel function On Off using the Left and Right buttons gt Det Level Select the judgment level of white pixel using the Left and Right buttons 1 16 gt Det View Select display of detected white pixel 6 Day Night gt Mode Select D amp N mode m Auto Filter operates automatically according to brightness Day The camera outputs the video image only in color Night The camera outputs the video image only in black and white Ext This menu automatically converts the COLOR Mode into the B W Mode or vice versa depending on illumination with an external sensor gt Night Mode Select B W Burst On Off gt Delay s Adjust the working time of the filter when D amp N mode is Auto 1 60 sec gt D gt N Level Select switching level Day to Night when D amp N mode is Auto 0 15 gt N gt D Level Select switching level Night to Color when D amp N mode is Auto 0 15 lt Bottom Line Menus gt When user entered in main menu and sub menus following menus will be appeared l Main Manu menu in bottom lines A Exit Save amp Exit B Load Load Default Value Il Sub Menu menu in bottom lines A Return Return to previous menu B Exit Save amp Exit 1 Exit Menu gt Save amp Exit Current environment values save Exit Disappear menu osd 2
Download Pdf Manuals
Related Search